Search Documents

By R. E. T. Hill

"A laboratory study was undertaken to determine the condensed equilibrium phase relations at 600°C in that portion of the quaternary Fe-Ni-Cu-S system which lies in the neighbourhood of the monosulphide solid solution (MSS). The study sought to determine to w hat extent copper affects the temperatures of stability and compositions of iron-nickel sulphides in bulk compositions similar to those of massive Fe-Ni-Cu ores. Experimental data, including stable phase assemblages and phase compositions, are presented.In the quaternary system at 600°C MSS forms stable phase assemblages with pentlandite, chalcopyrite solid solution, pyrite and vaesite. Over the range of bulk compositions displayed by natural ores copper as well as metal/sulphur ratio have a significant effect on the thermal stability of pyrite and pentlandite. Errors therefore accompany the widespread practice of ignoring copper or chalcopyrite when the mineralogical and compositional changes that have accompanied the initial cooling of primary magmatic sulphides or their subsequent homogenization during isochemical metamorphism are being deciphered. These errors are most significant for ores the bulk compositions of which lie tow ard the sulphur-deficient side of the cupriferous MSS. Temperatures as much as 300°C above the copper-absent value are possible for the interpreted upper stability limits of pentlandite in these ores.The experimental data show that up to 2.0 at% copper can occur in pentlandite stable at 600°C in a bulk composition equivalent to natural magmatic ores. This is equivalent to nearly 10 vol% chalcopyrite. Pentlandite contains more copper than coexisting MSS and the copper content of both phases increases with increasing iron."

Jan 1, 1984

By Xie Zhang, Jiang Diao, Xin Qiu, Lu Jiang, Bing Xie, Hong-Yi Li

"Duplex converter process, in which the first converter is used for removing phosphorus from hot metal (De-P), is an important way to produce low P-content and ultra-low P-content steels. In order to improve phosphorization removal and formation of slag with high basicity at relatively low temperature during dephosphorization converter process, effects of temperature, silicon content in hot metal and varied compositions of the De-P converter slag on phosphorus distribution between the slag and hot metal were investigated with thermodynamic calculations and by laboratory scale experiments in present work. Results showed that phosphorus distribution ratio between slag and metal was varied in 10.6~26.6 when basicity of the slag was in the range of 1.5~2.1 at 1370, and the distribution ratio was increased with increasing basicity and Fe10 content in the slag.IntroductionIt is known that phosphorus exists in steel in the form of solid solution, which can significantly improve strength and hardness of steel at room temperature. However, the plasticity and toughness of steel, especially the low temperature plasticity is sharply reduced and leads to high ductile-brittle transition temperature. This phenomenon is commonly known as cold brittleness of steel [1~3]. Hence, phosphorus should be removed as much as possible in the steelmaking process, because it is generally harmful to the iron and steel products."

Jan 1, 2013

By V. A. Chanturiya

The results study the minerals oxidation were obtained by us during the methods of microscopic, FT-IR spectroscopic, XRD and chemical analyses of sulphides in tailings of copper-nickel wastes in Kola peninsula. Sulphide minerals begin to oxidize already at the stage of stockpiling and initial stages of storing. The proportion of non-ferrous metals and magnesium oxide increases with time, calcium partially precipitating in the form of gypsum. Comparison of heavy metal contents in pore solutions in cur-rent and stale copper-nickel ore concentration tailings has revealed a significant difference in practically all the parameters. The lower metal contents in current tailing pore solutions (by 5~30 times) are probably due to the presence of float reagent residues blocking oxidation. Much lower concentrations of magnesium and calcium can be accounted for by the difference in kinetics: the rate of sulphide oxidation at this stage is much higher than that of solution interaction with non-metallic minerals as the result of which the solid phase ? solution equilibrium is not achieved. It is generally believed worldwide that it the mining wastes with acidic pore solutions that pose the greatest hazard for the environment. Our findings suggest that although the solution pH in all the samples is higher than 7.8, the contain heavy metal concentrations by far exceeding permissible values. The direct determination of the total and silicate Ni contents in the tailings from current production and in storage tailings has shown that both sulphide and silicate Ni forms occur in tailings. However, the role of silicate Ni is much larger in the storage tailings. The average silicate Ni content accounts for 10% of the bulk Ni content in the current tailings and it increases to 40% in the storage tailings. Thus, the storage tailings are marked not only by sulphide oxidation and the removal of water-soluble sulfates, but also by the interaction of sulfates with the silicate matrix. Although complete equilibrium is not achieved even within 30 yr under polar-region conditions, the major part of the Ni in fine-grained fractions passes into silicate form. The probability of Ni transition to the silicate form directly correlates with the dispersion of the material and the amount of chemically reactive serpentine and hydrochlorite. The migration of Ni as sulfates and its precipitation by chemically active silicates distorts the distribution of this component in the coarse- and fine-grained fractions that are typical of tailings from the current production of copper-nickel ores. On the one hand, the variation of the mode of Ni occurrence in storage tailings lowers the value of technogenic raw materials as a source of this metal.

Jan 1, 2014

By S. N. Yu

Tele-operation manipulators applied in this paper are systems for the remote handling and management of pyroprocessing related facilities in an Argon cell of the KAERI (Korea Atomic Energy Research Institute). Generally, these kinds of systems are composed of a master-slave system and its peripherals installed along the wall of the cell, with the master transmitting the user?s own motion to the gripper directly. This study introduced various considerations and modifications to improve the remote handling performance. The analysis of an operator's ability using his/her own upper arm motion range while manipulating the MSM, and considerations of its manipulation margin and the related tool modifications are also included. Finally, the test results of several remote handling tasks are presented, and an adequate operation strategy for the tele-operation system of hot-cell type facilities is proposed.

Aug 1, 2013

By Meifeng Zhi, Yuqing Niu, Xixin Chang, Fengqi Zhao, Weimin Qiu, Hao Wang, Zhenqian Wen, Zujun Shu

An applicable Eluex process was developed for acid in-situ leaching (ISL) uranium mine in Bayanwula. In this process, uranium was adsorbed with strong base anion resin from the pregnant solution, then the loaded resin was eluted by sulfuric acid. After D2EHPA extraction, the concentrated eluate was enriched, and the loaded organic phase was stripped by sodium carbonate. The yellow cake was obtained by sodium hydroxide precipitation at last. The uranium concentration in the loaded strip solution was 52.8 g/L. Parameters of the process were determined, and the impact of the Eluex process in underground leaching was also investigated. In industrial design, 95% of raffinate went back to elution and 5% back to in-situ leaching. No significant effect on uranium leaching or resin adsorption was found.

Jan 1, 2020

By Fabian Laumen, Sunny Schoone, Felix Leaman, ELISABETH CLAUSEN

The acoustic emission (AE) technology has a high potential for flow characterization in hydraulic transport processes. For instance, in deep-sea mining, there are applications where manganese nodules are transported from the bottom of the sea to the surface or a transport ship. Here, an AE-based flow characterization system plays an important role to avoid the transport of non-related objects. However, the structural materials for the components of this system must be carefully selected to ensure resistance against corrosion and a good AE signal transmission. Therefore, in this experimental study, we evaluated the AE attenuation behavior of four different materials that can be employed in marine environments due to their properties. The results were obtained using thin plates and they indicate which materials have the highest and lowest attenuations. Moreover, we provide insights regarding the different wave modes that propagate on the plates.

Mar 2, 2023

By M. R. Shahan, W. R. Reed, S. Klima, T. W. Beck, Y. Zheng

Testing was conducted to determine the ability of foam to maintain roof coverage in a simulated longwall mining environment. Approximately 27 percent of respirable coal mine dust can be attributed to longwall shield movement, and developing controls for this dust source has been difficult. The application of foam is a possible dust control method for this source. Laboratory testing of two foam agents was conducted to determine the ability of the foam to adhere to a simulated longwall face roof surface. Two different foam generation methods were used: compressed air and blower air. Using a new imaging technology, image processing and analysis utilizing ImageJ software produced quantifiable results of foam roof coverage. For compressed air foam in 3.3 m/s (650 fpm) ventilation, 98 percent of agent A was intact while 95 percent of agent B was intact on the roof at three minutes after application. At 30 minutes after application, 94 percent of agent A was intact while only 20 percent of agent B remained. For blower air in 3.3 m/s (650 fpm) ventilation, the results were dependent upon nozzle type. Three different nozzles were tested. At 30 min after application, 74 to 92 percent of foam agent A remained, while 3 to 50 percent of foam agent B remained. Compressed air foam seems to remain intact for longer durations and is easier to apply than blower air foam. However, more water drained from the foam when using compressed air foam, which demonstrates that blower air foam retains more water at the roof surface. Agent A seemed to be the better performer as far as roof application is concerned. This testing demonstrates that roof application of foam is feasible and is able to withstand a typical face ventilation velocity, establishing this technique’s potential for longwall shield dust control.

Jan 1, 2017

By M. R. Shahan, W. R. Reed, S. Klima, T. W. Beck, Y. Zheng

Testing was conducted to determine the ability of foam to maintain roof coverage in a simulated longwall mining environment. Approximately 27 percent of respirable coal mine dust can be attributed to longwall shield movement, and developing controls for this dust source has been difficult. The application of foam is a possible dust control method for this source. Laboratory testing of two foam agents was conducted to determine the ability of the foam to adhere to a simulated longwall face roof surface. Two different foam generation methods were used: compressed air and blower air. Using a new imaging technology, image processing and analysis utilizing ImageJ software produced quantifiable results of foam roof coverage. For compressed air foam in 3.3 m/s (650 fpm) ventilation, 98 percent of agent A was intact while 95 percent of agent B was intact on the roof at three minutes after application. At 30 minutes after application, 94 percent of agent A was intact while only 20 percent of agent B remained. For blower air in 3.3 m/s (650 fpm) ventilation, the results were dependent upon nozzle type. Three different nozzles were tested. At 30 min after application, 74 to 92 percent of foam agent A remained, while 3 to 50 percent of foam agent B remained. Compressed air foam seems to remain intact for longer durations and is easier to apply than blower air foam. However, more water drained from the foam when using compressed air foam, which demonstrates that blower air foam retains more water at the roof surface. Agent A seemed to be the better performer as far as roof application is concerned. This testing demonstrates that roof application of foam is feasible and is able to withstand a typical face ventilation velocity, establishing this technique’s potential for longwall shield dust control.

Jan 1, 2018

By F. Q. Cheng

As the important potash, the product yield of KCl in winter is low and the resources waste is serious according to the deficiency of collectors, which can be used in this condition currently. This paper studied on the change of contact angle, turbidity, and flotation recovery of KCl particles when different chain lengths, ratios of amines were used as collectors in KCl flotation process to get a new mixed collector. The contact angle values of KCl crystal in its brine solution added different amine collectors were first measured by captive bubble method. The turbidity of brine solutions were then measured by the laboratory turbidimeter at room temperature when different amine collectors were contained. In the end micro-flotation experiment using mixed amine with fixed ratios and ODA as collectors respectively at 5 °C, 23 °C were performed. The results show when the ratio of the mixed amine is DDA- 20%, ODA-60%, C20-20%, the contact angle at KCl surface is the maximum and the hydrophobic state is best. Meanwhile the result of turbidity measurement indicates that the dispersion of mixed amine colloids is better than the ODA collector due to the addition of DDA, which plays the role of frother. The flotation results also prove that the mixed amine is not only fit for the KCl flotation at room temperature but also fit for its flotation at low temperature. This study provides strong technical support to extend the production time of potash business in Chaerhan areas in China.

Sep 1, 2012

By Jing Zhang, Qing Xiao, Xulong Liu, Qiuju Li

"Pickling sludge generated from stainless steel production process contains large quantity of Cr, Ni, and Fe. The disposal of and fill sludge directly not only leads to the heavy metal dissolves in the soil and underwater, but also loss value metals. However, the major mineral phases of value metal are hydroxides and there are lots of calcium fluoride and water in the sludge. So the pickling sludge has to be pretreated before reduction-magnetic separation. The TG analysis, reduction reaction and magnetic separation were all used to study the pickling sludge. The result indicated that up to 900°C the total weight loss of pickling sludge was 22.32%. The mass contents of Fe, Cr and Ni in the tailings (non-magnetic) were 4.27%, 0.067% and 0.041% respectively.IntroductionSince 21st century, the stainless steel production in the world has been continuously increasing because of its excellent performance [1]. However, high stainless steel production means a high pickling sludge production. For example, in a stainless steel plant with waste water quantity of 100m3 /h, the production of pickling sludge will exceed 15 Kt/a. Pickling is essential for generating of a homogeneous and corrosion-resistant surface during stainless steel production subsequent process. Pickling of stainless steels is predominantly carried out with an aggressive solution, sulfuric acid H2S04 or composed of nitric acid HN03 and hydrofluoric acid HF [2]. During the pickling process, the pickling acids are recovered through ion exchange and metal ions such as Fe3+, Cr3+ and Ni2+ get into the acids forming the pickling waste water [3]. Then, the pickling waste water is precipitated with lime, forming pickling hydroxide sludge. It is not feasible to recycle or treat the pickling sludge using conventional methods, because the sludge has high contents of calcium fluoride and water but low contents of iron, chromium and nickel. However, it would also pose a potential environmental problem if deposited outdoors over a long term because it contains heavy metals such as Cr and Ni. At present, solidification/stabilization (S/"

Jan 1, 2014

By Shufeng Yang, Anping Dong, Yongfeng Chen, Jingshe Li, Lifeng Zhang, Liyuan Sun

"Instead of nickel-based stainless steel, a nitrogen-bearing stainless steel was produced to reduce the production cost stemming from the shortage of nickel recourses. Thermodynamic model to calculate the saturation nitrogen content in the stainless steel were developed and the model was validated by experimental measurement. The experiments were performed with a high temperature induction furnace. Nitrogen gas under constant pressure was injected into the crucible with a top lance by which the nitrogen was transferred to the molten stainless steel. The effects of chemical composition, temperature, superficial active elements and nitrogen-flow rate on transferring nitrogen to the steel were investigated and discussed.IntroductionWith the rapid production growth of stainless steels, nitrogen-bearing stainless steel has recently attracted more and more attention for their high strength and excellent corrosion resistance imparted by interstitial nitrogen without decreasing its toughness and ductility. Moreover, the addition of nitrogen to the stainless steel as a substitute for nickel leads a lower consumption of nickel, so significantly lowers the high production cost stemming from the shortage of nickel recourses. However, production of the nitrogen-bearing steel is difficult since nitrogen is a gas element and has a low solubility in the steel. So efficiently increasing the amount of nitrogen in steel continues to be one of the main concerns for the production of nitrogen-bearing steels.Currently there are some special processes to produce austenitic stainless steels with a very high N content, including pressurized electroslag remelting, counter-pressure casting, special induction melting and powder metallurgy, etc [1]. Special expensive vacuum system was required for these processes. Alloying nitrogen at a normal pressure can be performed by alloy addition or gas injection. Blowing nitrogen gas is a more economic and advisable method since the nitrogen-bearing alloy is quite expensive and contains high content of impurities. A number of investigations have been reported on the solubility of nitrogen gas in pure iron [2] but few in iron-based multi-component alloys such as stainless steel.In the current study, the effects of steel chemical composition, temperature, superficial active elements and nitrogen-flow rate on transferring nitrogen to the steel were experimentally investigated with a high temperature induction furnace."

Jan 1, 2011

By Markus Aspiala, Fiseha Tesfaye, Pekka Taskinen

In this paper, the standard thermodynamic properties of Ag3Sb and Ag6Sb intermetallic compounds have been studied by the solid state EMF-method, using Ag+ ion conducting β- alumina and AgI. The intermetallic compounds were synthesized from pure substances in evacuated silica ampoules and their formation were confirmed by the SEM-EDS analyses. The EMF measurements were made on electrochemical cells of the type [Ag | β-alumina | Ag-Sb] and [Ag | AgI | Ag-Sb]. The usage of β-alumina electrolyte, in this study, enabled thermodynamic measurements of the Ag-Sb-intermetallic compounds above 710 K, hitherto unreported. Based on the new experimental data, thermodynamic properties of the Ag-Sb-intermetallic compounds have been determined. The obtained experimental values have been compared with the available literature data.

Jan 1, 2015

By T. Moodleya, I. Govender

Despite the widespread use of DEM to simulate particle processes, comparatively little work has been done to evaluate its accuracy. One of the reasons is a lack of available measurement techniques that can capture dynamic information at the momentum transfer timescale which is lower than 10-6 s - typical of the kinetics occurring within the drum. This work makes use of Positron Emission Particle Tracking (PEPT), an in-situ method capable of measuring 3D kinematic data at 1000 frames per second. PEPT measurements are performed using 3 mm and 5 mm mono-size glass beads in a 300 mm diameter rotating drum at critical speeds that are relevant to industry. We undertake systematic ‘tuning’ of DEM with a view to optimising the agreement between experiment and simulation. To ensure an equitable comparison scale, both the DEM and PEPT data are coarse grained within representative volume elements. This work seeks to validate DEM predictions against experimentally derived PEPT kinematic measurements. Keywords: PEPT, nuclear imaging, DEM, Tumbling Mills

Jan 1, 2020

By R. W. Charles

The Los Alamos National Laboratory, under the sponsorship of the U.S. Department of Energy; is involved with laboratory and field experiments to assist in development of the Hot Dry Rock concept of geothermal energy. The field program consists of experiments in which hot rock of low permeability is hydraulically fractured between two wellbores. Water is circulated from one well to the other through the fractured hot rock. Our field experiments are designed to test reservoir engineering parameters such as heat-extraction rates, water-loss rates, flow characteristics including impedance and buoyancy, seismic activity, and fluid chemistry. Laboratory experiments were designed to provide information on the mineral-water reactivity encountered during the field program. Two experimental circulation systems tested the rates of dissolution and alteration during dynamic flow. SOlubil ity of rock in agitated systems was studied. Moreover, pure minerals, samples of the granodiorite from the actual reservoir, and Tijeras Canyon granite have been reacted with distilled water and various solutions of NaCl, NaOH, and Na.CO.. The results of these experimental systems are compared to the observations made in field experiments done within the hot dry rock reservoir at a depth of approxi-mately 3 km where the initial rock temperature was 150 to 200°C.

Jan 1, 1981

By Frank Wartman

RECENTLY Horace Freeman1 obtained a patent on a successful method of conducting a roasting procedure described as to general features by Carl Schnabel2 almost forty years ago. Essentially, the Freeman process of roasting consists in introducing the finely powdered sulfide mineral, suspended in air or any other suitable gaseous medium, into the upper portion of a heated chamber. The stream of suspended particles is directed vertically downward. A counter-current stream of gas introduced at the bottom of the chamber flows upward. The mineral particles are oxidized as they fall through the heated atmosphere of the chamber. All air required for the oxidation may be admitted either at the top or the bottom of the chamber, or may be divided between the top and bottom inlets in any desired proportion. Heat may be recovered by passing the gases leaving the furnace through a waste-heat boiler or other form of interchanger. In speaking of the results obtained in roasting pyrite, Freeman says:3 Steam yield from the boiler exceeds 1 pound of steam per pound of pyrite con-sumed, which pays the cost of operation of the burner. The oxide produced is in the form of fused particles or hollow shells of magnetite, containing about 65 per cent of iron. It contains the gangue material ordinarily produced in flotation concentrate, of course, but it is being found that most of this can be eliminated by magnetic separa-tion, and that the sulfur content, as consistently produced, is below 0.2 percent. This material is especially interesting as a high-grade iron ore, free from phosphorus and low in sulfur. It may be sintered or briquetted. It is even more interesting as a raw material for sponge-iron production, to be directly smelted in electric furnaces without the usual cooling of the iron powder and magnetic separation between the reducing kiln and the electric furnace.

Jan 1, 1933

By A. C. Watts

FOR several years, a mine in Colorado experienced considerable trouble from small fires caused by the blasting of coal. Although a well-known make of permissible powder was used, it was first thought that the powder ignited gas that might be present and that this, in turn, set fire to line brattices or to the coal. Experiments were, therefore, conducted with another make of powder, but the results convinced the superintendent of the mine, Robt. Williams, Jr., that the fires were not caused by the powder but by the high-voltage electric current used for detonating the shots. The mine "makes" gas very freely, giving off from three-fourths to a million cubic feet of methane per 24 hours. The coal is a good grade bituminous of a very free burning quality. Electric shot-firing from the outside after all men and animals were outside had been practiced for a number of years. The shooting circuit was connected with the main power circuit at the mouth of each entry. Shooting circuit switches were mounted in boxes, which were kept locked with the handle of the switch, in open position, showing through the bottom of the box. The door of the box could not be shut and locked when the shooting switch was closed. At the entrance to each room, or working place, a small switch, called the miner's switch, was placed on the shooting line. It was the duty of the miner, when entering his place at the beginning of the shift, to see that this switch was open and that it was kept open until he left the place at the end of the shift to go out of the mine. Grounded return was used for main power lines. The current was 500 volts, direct current, with 100 to 300 amp. The nearest working face was 9600 ft. from the shot-firers' switch outside the mine and the most remote working face was 2 ½ miles. The various working faces were scattered over a wide area between these two points.

Jan 9, 1925

By Robert Goodrich

THERE is a small area about Murray where bedded gold quartz veins occur in Prichard slate. The ore taken from the upper levels, during the early days, was free milling and was treated by stamp milling and amalgamation. There was likewise a considerable placer working. The report is current that tungsten (scheelite) was encountered, which interfered with the amalgamation in the stamp mills and which, in placering, collected in the riffles in the sluice boxes and. clogged them. Consequently, in the quartz mines, the scheelite, when encountered, was rejected, being thrown into the waste, sometimes inside the mine and at other times outside on the clump. The free surface ores became worked out and as the ore in depth became pyritic and rebellious to amalgamation the mines closed down. Last spring tungsten ore brought a high price, near $80 per unit, 60 per cent. W03 and up. This so stimulated the output of tungsten ore that old clumps were explored and waste stored in the mines was gone over. Tungsten was likewise mined from virgin ground. So the district produced quite heavily for a time. The condition now is different. The price is not so high, about $20 per unit W03, which makes profits questionable when mining in new ground. The accumulations from early clay mining have been exhausted and the output has greatly declined. The Golden Chest mine was the heaviest producer of tungsten. The months of June and July were spent at this mine studying the problem. Since the mine had produced both gold and tungsten, we looked forward to the problem of recovering both from what might be called a gold-tungsten ore. A study of the Golden Chest vein showed this not to be so there. While gold ore and tungsten ore come from the same vein, the tungsten ore is confined to a more or less disturbed or distorted portion

Jan 8, 1917

By L R. Sousa, M He

Rock burst is common in deep underground excavations and is characterised by a violent ejection of block rocks from excavation walls. It is critical to understand the phenomenon of rock burst and particularly the failure mechanism. Laboratory experiments are one of the ways. For that purpose, a rock burst laboratory test system was developed at the State Key Laboratory for Geomechanics and Deep Underground Engineering at the China University of Mining and Technology, Beijing. A true triaxial test system, designated the Deep Underground Rock Burst Analogue Test Machine, was developed, which can transfer a stress state from three-direction-compression on six surfaces to the compression on five surfaces with one set free. The rock burst experimental system comprises an acquisition of acoustic emission signals, a high-speed recording in order to accurately record the kinetic characteristics of rock fragments ejected during a rock burst event and the possibility of infrared thermography showing the surface temperature of the samples. In this paper, analyses of typical results from rock burst tests are presented with a description of the obtained results. The mechanisms of rock burst are illustrated, and a rock burst classification is proposed based on these laboratory tests. For the control of rock burst, the constant resistance, large deformation (CRLD) bolt or anchor is presented for accommodating the large displacement of surrounding rock masses and absorbing the impact of the sudden release of rock burst while outputting a constant resistant force in response to the external load. The CRLD bolt or anchor has had practical applications in underground mines. Finally, in situ tests performed in a tunnel at Qingshui coalmine, China, are analysed in detail.CITATION:He, M and Sousa, L R, 2014. Experiments on rock burst and its control, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 19–32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Orson Cutler Shepard

RECENT research work in the flotation concentration of minerals has been concerned mainly with flotation reagents and the mechanism by which collecting reagents are held to the surface of certain mineral particles. The fundamental question of why air bubbles cling to properly prepared mineral surfaces is usually dismissed with the statement that the surface is air-avid or water-repellent. In my article in MINING AND METALLURGY for June, 1932, I showed theoretically that surface tension relationships govern bubble attachment in Rotation. This explanation has not been accepted by many; probably be¬cause the difficulty of measuring solid-solution surface tensions prevented obtaining experimental evidence. If the surface tensions involved in the system [solution, mineral, air bubble] are responsible for attachment of the air bubble to the mineral, any change in the surface tensions should cause a corresponding change in the attachment of the air bubble. An example in which the mineral-solution surface tension could be varied was found with mercury. When mercury is in contact with solutions of certain electrolytes the surface tension at the contact of mercury and solution can be altered by electrical polarization of the mercury. The surface tension rises to a maximum as the mercury is given an increasing negative potential and then decreases with further increase in potential. The theoretical relation between the surface tensions and the attachment of an air bubble is given by the following equation:

Jan 1, 1936

By Guichao Wang, Geoffrey M. Evans, Graeme J. Jameson

"In this paper we present a new method for studying the detachment of particles from bubbles in a rotating turbulent eddy. The eddy is formed in a wall cavity in a two-dimensional water tunnel with transparent walls. When water flows through the tunnel, a vortical flow field develops in the cavity. The properties of the eddy can be modulated by changing the free-stream velocity of the water in the tunnel. Bubbles are pre-loaded with one or more particles in a fluidized bed flotation device located beneath the vortex cavity. Loaded bubbles are released one at a time into the cavity, and the motion of the bubbleparticle aggregate is studied using a high-speed video camera. The diameters of the particles and the bubbles, and the number of particles initially attached to the bubble, can be varied. The trajectories taken by the bubbles are quite complicated. In some cases, the bubble moves to the centre of the eddy, and particles rotate around its axis. If the rotational speed is sufficient, particles may detach due to centrifugal force. However, other modes were observed, including inertial detachment due to rapid changes in direction of the surface of the bubble, because of changes in trajectory of the bubble as a whole, or because of pulsations and oscillations of the bubble surface. Clusters of bubbles held together by particles were seen to form and reform. In the traditional explanation for the detachment of particles in flotation cells, it is assumed that particles detach from bubbles rotating in an eddy due to centrifugal force (Schulze, 1977). Although the conditions assumed in Schulze's theory may exist, it is only one of a range of phenomena that can lead to the detachment of particles from bubbles in a turbulent vortex.INTRODUCTIONThe recovery of particles by flotation methods is dependent on the particle size. The recovery in the existing flotation machines reaches a peak for particle size, typically in the range of 20 to 100 µm. This size range varies as a function of the particle’s properties (type and composites). For coarser particles, the recovery drops very quickly (Gaudin, Groh & Henderson, 1931; Jowett, 1980). If the upper size limit can be increased for flotation, dramatic savings in the grinding energy can be achieved."

Jan 1, 2016