Search Documents

Laboratory experiments show that the delay detonators, either electric (copper coated or aluminium) or non-electric (down-the-hole) as generally used in opencast mines and quarries have some scattering from the actual firing time due to manufacturing inaccuracy and variations in basic ingredients of the product. This scattering varies from 1 to 4 % depending on the product quality. Due to this component scatter, adverse blasting effects like misfires, overbreak, underbreak or fly-rock may occur if the design patterns are not judiciously made. It has also direct impact on muck profile and fragmentation.

Jan 1, 1999

By N Gkikizas-Lampropoulis

Selection of delay times to optimize fragmentation has been a controversial topic among researchers and blasting practitioners. This paper interprets previous experimental information on the effect of delay on fragmentation with the aid of some new experimental observations of the time of detachment of the free face of the blast as well as results of numerical modelling. It was shown that detachment of the burden occurs at delays shorter than the one which produced optimum fragmentation in the experiments, suggesting some fragmentation improvement due to gas action. In addition, at the spacing to burden ratio of the experiments, the damage zone from an earlier detonating charge extends the distance to the neighboring charge, essentially affecting the burden of some of the holes of the blast, at detonation time. Computer modelling demonstrated that increased spacing results is less overlap of stress induced damage zones meaning that there is less influence of delay on stress wave induced fragmentation. It was also shown that simultaneous initiation results in less back break, while increased back break may result even with short delay times.

Jan 1, 2016

By Martin F. Milligan

THIS short discussion of the effects of deoxidation on the mechanical properties of cast steels is intended to serve as general introduction to the subject of this afternoon's session. The subject is covered in detail in Mr. Carter's excellent paper. My material has been collected from the works of various investigators, several of whom are present today. For a definition of deoxidation, as applied to steel-furnace melting practice, we can best go to Briggs' book, "The Metallurgy of Steel Castings." Briggs says that deoxidation "includes all the phenomena in the final preparation of steel that would permit it to solidify free from gas cavities and from dissolved oxygen of all kinds." Various practices are used by welters to produce these end results.

Jan 1, 1947

By Chen Zhang

Polycrystalline Ti-rich NiTi thin films have been deposited from a single NiTi target using a DC magnetron sputtering system. Free standing film was obtained by using a single crystal silicon substrate. Thickness ofthe thin films is controlled at around 12 pm. In this investigation, the effect of deposition temperature on the microstructure and transformation temperatures of the thin films is studied. Influence of post heat treatment temperatures on the properties of the thin films is also investigated. Transformation temperatures of the thin films are determined by differential scanning calorimetry (DSC). The surface microstructure of the thin films is studied using a scanning electron microscope (SEM), and the crystallinity is determined using x-ray diffractometry. It is found that the thin film deposited on a hot substrate is crystalline even when the substrate temperature is as low as 300°C, while the normal crystallization temperature for an amorphous thin film is around 500°C. The microstructure of the film deposited on a hot substrate shows a very fine grain size. The grain size increases with increasing substrate temperature during deposition. The effect of post deposition heat treatment on grain size is minimal.

Jan 1, 1999

By S. Zhao, S. P. He, M. Y. Zhu, Y. Tao

"The effect of two refining slags (A: 1.0–1.8 CaO/Al2O3 ratio, 11–20 wt% SiO2; and B: 1.0–1.2 CaO/SiO2 ratio, 25–35 wt% Al2O3) on the inclusion morphology of a carbon structural steel (Q235B) was studied by controlling the balance between the steel and the refining slag at 1600ºC in a Si–Mo resistance laboratory furnace. The results showed that most of the inclusions in the molten steel balanced with slag A were formed by a lowmelting CaO–MgO–Al2O3–SiO2 system with a total oxygen content (T[O]) being fixed at 6–13 ppm. The inclusions in liquid steel balanced with the slag B were mostly formed by the CaO–MnO–Al2O3–SiO2 system, with T[O] controlled to 19–26 ppm. The overall size of the inclusions under balance conditions was higher in the steel reacted with the slag B than that reacted with slag A, with the latter showing more inclusions smaller than 3 um. In order to generate a large number of spherical CaO–MgO–Al2O3–SiO2 inclusions smaller than 3 ??m while decreasing the T[O] in the resulting steel, the composition of slag A should be used. This composition allowed improving the cleanliness of the slab, and is also advantageous for the castability of the molten steel. IntroductionThe sample used in this study was a typical carbon steel manufactured by CQ Steel. The galvanized, tinned, and plastic composite steel plates made of the original plates are used extensively for decorative panels, general dust pipes, drums, instrument cases, switchboxes, and train cars, among other uses. The target control composition is shown in Table I. The S and P contents are usually fixed during production below 0.020 and 0.025 wt%, respectively, with the aim of reducing longitudinal cracks on the slab surface."

Jan 1, 2017

By M. Epiney, A. Ghahreman, R. Kim1and

"Pre-oxidation and cyanide leaching behavior of gold in the presence of sulfide minerals were reviewed, focused on the effects of oxygen injection in the gold leaching process. Generally, pre-oxidation and gold leaching kinetics from iron sulfide refractory minerals, such as pyrite, pyrrhotite, marcasite, pentlandite and arsenopyrite, can be enhanced with higher dissolved oxygen (DO) concentration. However, most of copper sulfide minerals dissolved well both in water and cyanide solutions, and copper from the minerals consumed DO and cyanide to oxidize and leach. Only in the presence of chalcopyrite, gold leaching was effectively occurred with increasing DO. However, chalcocite and covellite severely retarded gold leaching. Stibnite, an antimony mineral, formed a passive film on the gold surface under any DO conditions, and it slowed gold leaching. This impeding effect can be alleviated by leaching at low pH or adding lead salt. Using oxygen and lead together can make synergistic effect in oxidation of sulfide minerals and can enhance gold extraction. Depending on the mineralogical characteristics of the ore, the optimum DO and lead concentrations can be optimized. However, lead can cause environmental problems, and so its dosage should be minimized or eliminated by substituting it with oxygen injection.INTRODUCTIONGold ores containing sulfide minerals are becoming more significant as high grade gold oxide deposits are continuously becoming difficult to find. In light of this situation, to produce more gold, recovery methods from refractory gold ore containing various sulfide minerals should be investigated. Generally, sulfide minerals have impeding effects on gold leaching: formation of a passive film on the gold surface, high consumption of chemicalssuch as cyanide and oxygenduring leaching, reduction of gold cyanide by sulfide ions, etc. (Senanayake, 2008). Therefore, sulfides must be properly treated for better gold recovery. Pre-oxidation of sulfide minerals by injecting pure oxygen can decrease the impeding effects in gold leaching. Prior to cyanidation, sulfide minerals can be oxidized to metal hydroxide and sulfate form, which consume negligible cyanide in the following cyanidation circuit (Bodnaras et al., 1993). Moreover, gold cyanidation can be enhanced by increasing concentration of the dissolved oxygen (DO). In general, the optimum concentration ratio of [CN-]/[O2] is calculated as 6, but it goes higher in the real system (Marsden &House, 2006), which means that the reaction is typically controlled by DO concentration."

Jan 1, 2017

By Rina Kim

There are many factors which affect the gold cyanidation mechanism— mineral composition, free cyanide and dissolved oxygen (DO) concentrations, heavy metal additions, etc. This study combines electrochemistry and surface analysis methods to examine the effectiveness of the above factors on gold cyanidation process. Three gold ore samples were used in this study. Sample 1 was a pyrite concentrate, contained mercury and silver. Sample 2 also contained sulfide minerals, including galena. Sample 3 contained pyrite with sphalerite and galena. In the case of samples 1 and 2, the presence of heavy metals enhanced gold cyanidation kinetics, though the addition of higher DO was not effective on improving the kinetics. Sample 3 showed an opposite behavior: the kinetics was not enhanced by galena, because of its relatively small amount, however, the use of higher DO made improvement in the gold leaching kinetics, likely caused by iron species generated by pyrite oxidation.

By John C. Nigro

Bench scale and pilot plant research was conducted using dolomites (CaO,MgO) lime as the basic additive in the preparation of self-fluxed pellets from a typical magnetic taconite concentrate (5.57 S_2). The specific objective of this investigation was to ascertain the viability of the magnesia lime pellets in high temperature oxidizing and reducing atmospheres. Pellet basicity and induration temperature were major parameters affecting fired pellet quality; temperatures ranging from 1,200° to 1,250" C appeared to be the most favorable for production of self-fluxed pellets with basesities (B) above 1.0. Comparison of the mechani¬cal and metallurgical properties of regular (acid) and self-fluxed pellets (B 1.55) produced under similar conditions in a modified grate pelletizing machine showed that the self-fluxed pellets were more resistant to abrasion and to high and low temperature reduction disintegration, an important consideration in commercial application. The Plus 3 mesh Linder index increased from 68 percent (regular pellets) to over 90 percent (self-fluxed pellets). The reducibility and swelling indices of the self-fluxed pellets were found to be comparable to the regular pellets.

Jan 1, 1972

By T. Belem

In-stope backfill will cure under effective stress, which develops due to a combination of mechanical consolidation (free draining material) and ??chemical consolidation?? (self-desiccation mechanism). A good knowledge of all the drainage and consolidation characteristics of cemented paste backfill is crucial for a better design of underground backfilling sequencing. From many of the existing results and studies done by various authors, as well as the availability of some in-stope backfill pressure data measurements during and after filling, it is possible of developing a procedure of backfilling sequencing. Hence, the objective of this study is to provide a guide for underground backfilling sequencing in the view of preventing the development of excess pore pressure that will affect both the stability of the barricades and the strength development of the backfill. This will be possible by considering the interaction between consolidation/drainage rate, filling rate and binder hydration rate.

Aug 1, 2013

By K Le Bron

Fatalities that occurred because of rock falls in off-reef excavations (excluding shafts) over the last three years range between ten per cent and 20 per cent of the total number of fatalities that have occurred due to rock falls in the South African mining industry. These rock falls, mostly exacerbated by blasting practices, occur because of failure on discontinuities within the rock mass. Among other reasons of their occurrence is insufficient support installation or the incorrect assessment of rock mass conditions. This report presents qualitative analysis intended to outline rock stability conditions in tunnels subjected to dynamic loading. Seismic waves including those created by firing an explosive charge in tunnel rocks are considered. The rock behaviour is monitored using geophones and extensometers variably installed to record the near and far effects of roof bolt support units on a dynamically loaded rock. The paper discusses the results of field investigations.

Jan 1, 1999

By H. Doostmohammadi

During the tapping of liquid steel from Electric Arc Furnace (EAF), some slag is carried over into the ladle. High levels of FeO and MnO in slag carryover increase the oxygen activity in steel melt leading to oxide inclusion formation during the ladle treatment. The demand on cleaner steels requires minimization of carryover slag. In this work, the effect of EAF slag carryover on ladle slag-steel equilibrium calculations for a hot working tool steel was studied. Steel and slag sampling were done in Uddeholm Tooling AB in Sweden. XRF and OES techniques were used to determine chemical composition of samples. The quantity of slag carryover was calculated based on a mass balance followed by thermodynamic calculations on metal-slag equilibrium using Thermo-Calc software. The agreement between predictions and experimentally determined compositions was good. This leads to the development of a prediction method for optimizing the production of other tool steel grades.

Jan 1, 2009

By Julian Johnson

The effect of changing redox potential (Eh) on the high temperature sulfuric acid leaching of Western Australian dry-land nickel laterite ores has been investigated. In particular, the effect of added reductant (sulfur, sodium sulfite) or oxidant (potassium chromate) on Eh, leaching kinetics, metal extractions, acid utilisation and leach residues has been determined. Three separate ores - nonhonitic ores from Murrin Mumn and Bulong, and limonitic ore from Cawse - were used in the study. Sulfur addition varied from 0 to 7.8 kg/t ore. The total acid loading was kept constant at 430 kg/t (Murrin Murrin ore) and 330 kglt (Cawse ore), whilst acid loading for Bulong ore was varied according to the presence of either reductant or oxidant. The extraction of both nickel and cobalt from limonite ore remained unaffected when small amounts of sulfkr were added, but addition of even small amounts of reductant to nontronitic ore decreased both nickel and cobalt extraction. Increased manganese and iron dissolution were observed as the levels of reductant increased, accompanied by a decrease in chromium dissolution. As the iron dissolution increased, free acidity decreased, with a subsequent decrease in nickel extraction. In contrast, addition of oxidant lead to reduced iron and manganese dissolution and slower extraction of nickel and cobalt. Keywords: Limonite, Nonhonite, Eh, Nickel Extraction

Jan 1, 2004

By L. G. Wang

The stability of foams and froth plays an important role in flotation, in which small amounts of relatively weak non-ionic surfactants (frothers) are used to produce air bubbles and foams. In the present work, factors affecting the stability of the foams produced in the presence of common frothers, such as n-pentanol, n-octanol, methyl isobutyl carbinol (MIBC), and polypropylene glycol (PPG), have been studied. We used the thin film pressure balance (TFPB) technique of Schelud-ko-Exerowa type to measure the equilibrium film thicknesses. The results were used to determine the contributions from the various surface forces to the disjoining pressures in the thin lamellae (foam) films formed between air bubbles. In addition, we used a model developed by Wang and Yoon (Colloids and Surfaces A: Physicochem. Eng. Aspects, 2006) to calculate the elasticities of the lamellae films at the critical thicknesses at which films rupture. The surface forces and elasticity da-ta were then compared with the foam stabilities in the presence of the various flotation frothers. It was found that foam stabilities are controlled by both film elasticity and surface forces, the relative contributions of which change with frother type and concentration. In general, surface forces play a more important role at relatively low frother concentrations, while elasticity plays a more important role at higher concentrations. At the frother additions usually employed in the mining industry, MIBC relies on surface forces while PPG-400 relies on film elasticity in producing stable foams. The former is capable of dampening the hydrophobic force, which is a major attractive force destabilizing lamellae films, while the latter is capable of reducing surface tensions at low concentrations.

Jan 1, 2014

By Guillermo Krstulovich

Pillar strength is a fundamental variable in the design of room and pillar mining. A number of researchers have investigated the strength of mine pillars by loading cubical, cylindrical and rectangular model pillars to failure in a compression testing machine (1). Several of these researchers have observed an increase in the compressive strength of model pillar with an increase in friction at the platen-specimen interface (2, 3, 4, 5). It has been postulated that the friction prevents lateral expansion of the specimen, thereby exerting a confining pressure at the interface. Seldenrath and Gramberg in their work with cylindrical specimens of limestone and marble noted that the effect of clamping the ends of the specimens, i.e., to restrict lateral movement of the specimen face, was to increase the compressive strength about 10% for marble and from 50-75% for the limestone, as compared to the same type of specimens when tested with the end planes free (6). No attempt was made to determine the confining pressure exerted by the clamps. In recent years, Bureau of Mines has conducted an extensive study, similar to Seldenrath and Gramberg's, with dog bone specimens. The confining pressure exerted by the clamps was determined and an increase in the compressive strength with increasing confining pressure noted (7, 8).

Jan 1, 1970

By Evangelos Petrakis, Kostas Komnitsas

This study investigates the evolution of dimensional properties of grinding products, namely, the mass, the surface area, the length, and the number of particle distributions with the energy input in a ball mill. The size analysis of the mill products enables the calculation of the mass distribution of each material at predetermined size classes and then the determination of the other dimensional properties by taking into consideration the geometry of the particles. Based on the distribution of dimensional properties, an effort was made to determine whether the grinding products are fractal in nature. The effect of material type and grinding conditions on the relationship between the dimensional properties and the specific energy input was also investigated. Special importance was assigned to the study of the specific surface area and the surface area production rate, both during the initial grinding stages and at higher energy levels. The determination of the surface area production rate allows the identification of the grinding limit and the maximum specific surface area which could theoretically be achieved. This approach has as ultimate objective the maximization of energy efficiency and subsequently the minimization of the high grinding cost.

By Martin Langenderfer, Catherine Johnson, Phillip Mulligan, Kelly Williams

The physical geometry of a charge has a direct correlation to the geometry of the shock wave. This relationship appears strongest within the boundaries of the visible fireball. As the shock wave propagates outward past the limits of the fireball, the theory states that the geometry of the shock wave should even out and become more spherical. This paper investigates pressure vs. time at two distances, one ‘Near Field’ at the extent of the fireball and one ‘Far Field.' The two Fields were instrumented with three free-Field pressure probes from PCB oriented at 0, 45, and 90 degrees to the front face of the charge, in the same horizontal plane as the charge. This orientation allows for the comparison of the shock wave from the face and vertices of the charge. All the pressure sensors were connected to a Data Acquisition System (DAS) recording at 2 million samples per second (2MS/s). Two high-speed cameras, a Phantom and an MREL Ranger II, recorded the detonations for qualitative examination of the fireball, and the shock wave. Three charge geometries were used and compared to the shock propagation of a sphere. The other geometries tested are cylinders, cubes, and tetrahedrons. Charges were made from a PETN based sheet explosive. In the Near Field, a lower pressure is observed along charge vertices with highest pressures from each face. In the Far Field, vertices record a higher pressure, possibly due to the shock waves from the adjacent faces intersecting, indicating that shock pressures do not always even out in the Far Field. This paper will describe the methodology and findings of this experiment and attempt to determine causality for trends in the data gathered.

Jan 1, 2018

By X. -G. Chen, K. Liu

Nowadays, great interests are rising on aluminum alloys for the applications at elevated temperature, driven by the automotive and aerospace industries requiring high strength, light weight and low cost engineering materials. As one of the most promising candidates, Al-Mn-Mg 3004 alloys is found to possess considerably high mechanical properties and creep resistance at elevated temperature resulted from the precipitation of a large number of thermally stable dispersoids during heat treatment. In present work, the effect of Fe contents on the evolution of microstructure as well as high temperature properties of Al-Mn-Mg 3004 alloys has been investigated. Results show that the dominant intermetallic changes from a-Al(MnFe)Si at 0.1 wt.% Fe to Al6(MnFe) at both 0.3 wt. % and 0.6 wt. % Fe. In the Fe range of 0.1 to 0.6 wt.% studied, a significant improvement on mechanical properties at elevated temperature has been observed due to the precipitation of dispersoids, and the best combination of compression strength and creep resistance at 300°C is obtained in the alloy with an intermediate Fe content (0.3 wt.%) with finest size and highest volume fraction of a-Al(MnFe)Si dispersoids. The superior properties obtained at 300°C makes 3004 alloys more promising for high temperature applications. The relationship between the Fe content and the precipitation of stable dispersoids as well as the materials properties has been discussed.

Jan 1, 2015

By B. van Beek, J. H. Zietsman, A. Lexmond, N. J. Andrew

"In platinum group metals (PGMs) smelting, the slag-to-matte ratios are very high (approximately 4:1 to 9:1). The slag temperature therefore has a strong influence on matte temperature, which is a continual concern due to the low matte melting temperature and its resultant high superheat. Maintaining a stable slag temperature is therefore a critical safety and operational issue. This project aims to improve the understanding of the slag bath temperature drivers so that a more effective slag bath temperature control strategy can be implemented.With the aim of developing a multiphysics model of the furnace, extensive data analysis was performed to develop an in-depth understanding of the process before the start of modelling work. In this work, the effect of fluctuating furnace feed composition on slag temperature was examined. The results are based on equilibrium calculations using FactSage, implemented with ChemApp.A method was developed, using an equilibrium calculation at 25°C, to convert the available chemical assays to approximate mineralogical assays in order to determine the feed enthalpies. Actual 2013 furnace feed data was used and the average specific energy requirement to produce slag and matte at 1600°C was calculated to be 671 kWh/t concentrate. The furnace energy input was then kept constant, and it was found that the slag temperature varies significantly as a function of the feed composition. These results were compared to actual slag temperatures measured on site. It was found that close management of the furnace energy balance is important for maintaining a stable slag temperature."

Jan 1, 2014

By Hassan El-Shall, Ayman El-Midany, Patrick Zhang

Bench and pilot scale testing results suggest that significant improvement in dewatering characteristics of fine particles could be obtained by the addition of fibrous materials. Case studies involving flocculation and dewatering of wastes from phosphate, bauxite, and kaolin processing plants are presented in this paper. Several dewatering techniques were investigated, including sedimentation thickening, filtration, centrifugation, dewatering on screens, and seepage-induced dewatering and consolidation. Advantages and limitations of commercial application of some of the developed techniques arc discussed.

Jan 1, 2004

By C. P. Fang, V. A. Marple, K. L. Rubow, P. H. McMurry

"It has been known for some time that sizes of aqueous particles may be affected by flow-induced relative humidity (RH) changes. The RH of air flowing through an impactor decreases as a result of pressure drop through the impactor and increases because of aerodynamic cooling within the high-speed jets, as illustrated in Figure 1. Because the sizes of aqueous particles depend on RH, the impaction stage on which such particles are collected may be different from the stage where they ought to be col¬lected, based on the particle size at the sampler inlet.Fuchs (1980) reviewed literature on water vapor condensation in impactors. The reviewed impactors operated at jet velocities of 100-250 m/s. Particle size increases ow¬ing to water vapor condensation were found in all cases. In one case (Khorguani et al., 1970), it was found that very small droplets (Dp <_ 0.02 um) containing sodium chloride and silver iodide were collected in an impactor with a cut point of 0.32 µm and a jet velocity of 100 m/s. Fuchs believed that such particles could not be captured in an impactor without having been enlarged by condensation. Winkler (1974) sampled at¬mospheric dust with a rectangular nozzle impactor that had a nozzle cross section of 0.3 x 15 mm, a cut size of 0.4 um, and an average jet velocity of 100 m/s. No adhesive was used on the impaction plate. The collection efficiency increased as air humidity was increased from 20% to 100%. The effect was especially noticeable in the increased collection efficiency for hygroscopic particles, and was attributed to condensation.Extensive theoretical and experimental research work on the distortion of the particle size distributions in impactors was done by Biswas and coworkers (1985, 1987). The impactors employed in the study were a low-pressure impactor with high jet velocity stages (Hering et al., 1978, 1979) and a conventional six-stage impactor, Sierra's model 226, operated in the incompressible regime. Ammonium sulfate aerosols were chosen for the study. In the low-pressure impactor, an orifice operating at a Mach number of 1 causes a sudden pressure drop, significantly reducing the RH in the next two stages (stages 5 and 6). This results in a 0.15-um diameter ammonium sulfate droplet shrinking to about 0.07 um at stage 5 when the inlet RH is 95%. In stage 7, the tempera¬ture drop is considerable because the jet speed is sonic. For an inlet RH of 95%, a 0.03 um droplet grows to about 0.06 um. However, the same size droplet at an inlet RH of 25% grows to only 0.04 um. For the Sierra model 226 cascade impactor that is operated with a Mach number of 0.27 at the last stage (stage VI), it was found that for an inlet RH of about 67%, particle growth would occur in stage VI. At 80% RH, both stages V and VI were affected. Biswas et al. (1987) stated that Mach number alone does not determine the size biasing; the type of aerosol, the inlet conditions, the temperature and pressure ratio, and the impactor geometry (throat length, jet-to-plate distance, etc.) must be considered for each stage in evaluating the distortion of the particle size distribution."

Mar 1, 1992