Search Documents

By C. W. Lawr

THE ores mined by the Santa Gertrudis Co. at Pachuca, Mexico, are mainly silver-bearing; they also yield some gold and carry a little copper. Strong cyanide solutions are used to dissolve the silver and gold, and the mechanical loss of cyanide at the tailings filter has been considerable. Prior to the year 1923, the pulp, after agitation, was given a 35 to 37-min. wash with barren solution in a Butters-type leaf filter; the discharged slime cake was repulped and pumped into eight Merrill self-sluicing slime presses in which the slime was given a further wash with barren solution for 25 to 35 min., followed by a 10-min. water wash. At that time the barren solution titrated around 0.350 per cent. free KCN and 0.500 per cent. total KCN. (Aero brand cyanide is used.) It can readily be seen that a 10-min. water wash would leave considerable cyanide in the filter cake, which of course was a total loss. This averaged 0.522 kg. (1.15 lb.) KCN per ton of solution. As the daily discharge to. the dam was 1600 tons1 of slime of a 2: 1 ratio of liquid to solid, the value of this mechanical loss of cyanide was an important item and its recovery held alluring possibilities.

Jan 1, 1929

By A. Khodadadi, M. Abdolahi, P. Taimory

Cyanide is used by the mining and chemical industries in tremendous quantities without attention being given to its hazardous properties. The use of cyanide compounds in mining is one of the most important environmental issues for the mining industry due to the acutely toxic properties of many cyanide compounds to humans and aquatic life. Cyanide tends to react readily with most other chemical elements, producing a wide variety of toxic, cyanide-related compounds and because cyanide is carbon based an organic compound it reacts readily with other carbon-based matter, including living organisms. This research is aimed at investigating a feasible and economical technique for the removal of cyanide from tailing wastewater of Muteh gold mine. In this research, removal from Muteh factory's waste water, was achieved at Tarbiat Modares University's mineral processing laboratory through the oxidation of cyanide by calcium hypochlorite. Cyanide oxidizes and changes to cyanide (CNO-) which is 1000 times less environmentally hazards than cyanide. Cyanide titration was accomplished using Rhodanine solution and silver Nitrate. Cyanide concentration in the wastewater, was 270 mg/L. Cyanide removal was achieved at an optimum pH of 12.3. However, at higher temperatures, cyanide removal was complete at this pH level. Optimum Dosage for complete removal of cyanide using calcium hypochlorite was 1.43g/L.

Jan 1, 2005

By G. Van Weert, J. F. Breedveld

Both regular and Silver Impregnated Activated Carbon (SIAC) were studied for their effectiveness in removing WAD (Weak Acid Dissociated) cyanides from solutions at pH = 10. SIAC has already been shown to be effective in the removal of free cyanide down to 30 ppb or less. The present work deals with complexed cyanides. Zinc cyanide was used to represent the WAD component. At pH=10, in either batch or column tests it was not possible to lower the total cyanide in solution from either 30 or 8 ppm to less than 1 ppm, using SIAC, regular activated carbon as received, or after grinding. Silver (metal) impregnation of the carbon was not beneficial in the removal of WAD cyanide. However, when silver is added as silver ions (nitrate), the cyanide is adsorbed as silver cyanide in preference to zinc cyanide. The latter compound converts to zinc (hydr) oxide. This way, the cyanide concentration in solution can be lowered below 1 ppm, even when zinc cyanide is already adsorbed on the carbon used. A single exploratory test with added copper ions indicated a similar effect for that system.

Jan 1, 2004

By Charles H. Buclmam

"Environmental regulatory requirements for discharge of solutions and closure of operations for the gold mineral processing industry have been gradually lowered and in certain instances have been targeted to USEP A inorganic drinking water standards for dissolved ions in solution. The use of jar tests for water treatment process development is suitable for preliminary scoping work to be conducted in the research laboratory, as well as for optimization studies at the site of the treatment requirement. This paper will describe experimental methods which were performed using standard jar test equipment in efforts to produce solutions which meet USEP A inorganic drinking water standards after chemical treatment of cyanide solutions. The materials tested included gold bearing pregnant solutions from heap leaching operations, gold plant barren solutions from the Merrill-Crowe zinc cementation gold recovery process and gold heap leach wash solutions after carbon-in-column gold recovery. Experiments included cyanide destruction with sodium hypochlorite and arsenic and selenium co-precipitation coupled with mercury precipitation.IntroductionCyanide leaching solutions are used to selectively dissolve metallic gold from commercially viable mineral deposits. The heap leaching process involves stacking of gold bearing ores on specially designed solution containment pads and percolating alkaline cyanide solutions through the ore to dissolve the gold. Pregnant solutions containing the dissolved gold are collected and sent through a gold recovery process. After selective recovery of the gold, the barren solutions are recycled to the gold extraction process after adjustment of the solution alkalinity and available cyanide concentrations."

Jan 1, 1997

By Kambhampati C. Rao, Cecil Lue-Hing, Nabih P. Kelada, William B. Willborn

improvements in the analytical techniques for cyanide speciation can furnish useful information about the behavior of the different cyanide species in the receiving environment. This could be of help to the environmentally concerned public and the regulatory agencies in the assessment of cyanide limits for effluents, stream quality, and land disposal of cyanide bearing wastes. In addition the ability to distinguish the free cyanide and the weakly bound cyanide from the strong ULTRAVIOLET IRRADIATION UNIT (LAMP, COIU3' HOUSING) FIGURE 1 complexes, as well as transformation to thiocyanate is also needed by different industries, such as mining and metal finishing, etc., to evaluate the efficiency of several processes. Cyanide has been used for the recovery of gold since the late 19th century. Although cyanide leach solutions are mostly recovered and used again, a large quantity of cyanide bearing wastewater becomes unfit for use and has to be treated before it can be released into natural waterways.

Jan 1, 1992

By A. G. Roach

IT IS generally stated that the gold ores of Nova Scotia are free-milling, and for the most part this is true. However, there is a certain proportion of the gold finely disseminated throughout the sulphides, notably arsenopyrite, and this gold is definitely not recoverable as 'free-milling' gold by amalgamation. The proportion of free-milling gold to total gold seems to vary widely in different localities in the Province and is lowest in deposits of the fissure-vein type. The problem of recovery of these relatively recalcitrant values is usually one of economics, in some plac.es a simple gravity concentrate being of such low tenor that its extraction and subsequent disposal will not bear the costs involved. In other cases, such a high percentage of values escapes from the mortars and plates that concentration is definitely indicated. The size of the mining operation is also an important factor. In the large majority of cases, however, some concentrating step is warranted, even if the resulting concentrate is stock-piled until sufficient has accumulated to justify further treatment.

Jan 1, 1940

By JIAQI JIN, Joe Milbourne, Maoming Fan

Gold is very important to support the financial system, and to be used in industries of the jewelry, high-tech fields such as electronics and aerospace, etc. Gold is mainly extracted from three types of ores: primary ore (vein gold), placer (alluvial gold) and associated ore. Cyanide was widely used in gold ore flotation to depress gangue minerals and leaching/cyanidation. The process of extracting gold from gold ore, its separation and flotation concentrate, specifically through a technique called cyanidation or cyanide leaching. This method, which has been dominant since the 1970s, utilizes a dilute solution of cyanide to dissolve gold from the ore. While effective, the use of cyanide raises environmental and safety concerns due to its high toxicity. Cyanide spills can have severe environmental consequences. This has led to the exploration of alternative, environmentally friendly reagents. This paper discusses processing results using the alternative flotation depressants such as sodium sulfite (Na2SO3), etc. to produce a goldrich flotation concentrate for sale to a smelter or as feed to an alternative leaching agent. and methods to extract gold from ore without relying on cyanide.

Feb 22, 2026

By Roger L. Beals, George A. Tweedy

I. INTRODUCTION. THE results of the cyanide-operations, given in detail in the following paper, show the progress that is being made at the Minas del Tajo. The old pan-amalgamation process, in operation up to and including 1905, while paying a profit on high-grade ores, was no longer able to treat profitably the ores in sight at that time, hence an alteration in the process was imperative. The success of this alteration is eloquently expressed by the following data Pan- Amalgamation. Cyanidation. 1905. 1907. 1903. Tons treated, . . 51,387 53,983 69,300 Value per ton (U. S. currency),. $10.75 $8.39 $8.28 Extraction, per cent., 65.00 88.50 S7.45 Extraction, per ton. .- $7.00 $7.4.; $7.24 Total cost, per ton treated, 6.50 4.311 4.01 Profit, per ton treated, . . 0.50 3.07 3.23.;

Feb 1, 1910

By Courtney A. Young

Cyanide is a fast-acting, highly toxic substance but, at the same time, is deemed essential for sustaining life as well 'as our standard of living. In this manuscript, the facts about cyanide are presented beginning with a brief history and definition and ending with a discussion on cyanide alternatives. Other topics include speciation, physical characteristics, toxicity, manufacturing, cyanogenics, cyanide cycle, separation, destruction, and markets including those outside the mining industry. Emphasis, of course, is placed on gold production by leaching and how it is influenced by ore type, mineral characteristics and economics as well as its advantages and disadvantages.

Jan 1, 1998

By C. G. McLachlan

Abstract This paper deals with the application of the cyanide process to recover gold from a pyrite concentrate produced by means of differential flotation. This concentrate before cyanidation contains from 0.09 oz. to 0.14 oz. gold per ton, of which only about 60 per cent is recoverable. The rest is so fine that it remains interlocked in the pyrite and therefore is not acted on by the cyanide. The concentrate also contains about 15 per cent pyrrhotite and 0.4 per cent chalcopyrite, both of which are cyanicides. The cyanicidal effect of the pyrrhotite is inhibited by preacracing the pulp with lime, and maintaining a high lime alkalinity during cyanidation. The effect of the chalcopyrice is reduced as far as possible by removing those particles which are free by means of a further flotation step immediately prior to cyanidation. This involves the flotation of some very fine material. After nullifying as far as possible these two cyanicides, the concentrate is cyanided directly, i.e., without being roasted. This leaves the pyrite available for subsequent sale as a source of sulphur dioxide and sulphuric acid, and the entire residue of the cyamde plant, amounting to about 500 tons per day, 1s now being disposed of in this way. Prior to deciding on direct cyanidation, a number of laboratory roasting tests were made. These showed chat, 1f proper control were exercised, a better recovery of gold could be effected from the roasted product than by the direct method of treatment. The tests also showed that the capital cost o the plant would be much higher than that needed for the procedure adopted. The possibility of subsequently selling the pyrite for its sulphur content would also have been eliminated. Introduction A previous paper has described in considerable detail the application of the flotation process to improve gold recovery from Noranda's milling ore, and in so doing has covered the production of an auriferous pyrite concentrate. The present paper deals with the recovery of gold by cyanidation from that concentrate. This gold, though intimately associated with the pyrite, can, for metallurgical purposes, be considered as all occuring in the native state.

Jan 1, 1946

By T. H. Oxnam

INTRODUCTION. THE predominating value of the ores now being treated by the Palmarejo and Mexican Gold Fields, Ltd., is silver, although some gold is also carried. The present method of treatment consists of wet-crushing and concentrating, followed by the cyanidation of the unroasted sands and slimes. The sands are treated by leaching and the so-called accumulated slimes by a system of agitation and decantation. It is only within very recent years that the cyanidation of unroasted silver-ores has been commercially successful. In fact, at the time operations were begun at the cyanide-plant at Chinipas, February, 1902, I knew of no other leaching-plant treating similar ores successfully. The cyanide treatment of the Palmarejo ores differs but little from the ordinary practice in cyaniding gold-ores; and perhaps but little, if any, new information concerning the metallurgy of silver is to be gleaned from it. PALMAREJO MINE. The Palmarejo mines are located in the southwestern part of the State of Chihuahua, Mexico, on the foothills of the Sierra Madre mountains, at an elevation of 3,200 feet. The mills, 12. miles distant, are situated on the Chinipas river, near the town of Chinipas, which is about 150 miles northeast of Agiabampo, on the Gulf of California. Supplies are shipped via this port as this route is the best and most direct to the property. The ore-bodies in the Palmarejo mines have been deposited. along a series of rock-fractures, caused by an intrusion of eruptive rock. The most important of these fractures or fissures, both in width and value, are the Prieta and Blanca veins, which.

Jul 1, 1905

By Paul Doherty

Expansion of the global piling industry has been coupled with significant research efforts investigating the mechanisms controlling pile capacity. Static pile design has transitioned from total stress approaches toward effective stress design, with associated improvements in predicting pile performance. As a result, the available literature is heavily skewed toward static capacity prediction. However, when considering piles offshore, the majority of loading is not static but highly variable and cyclic in nature. This paper outlines the additional factors that require consideration for cyclic pile design, including elevated loading rates, cyclic displacements and capacity degradation. A review of the literature identified a number of cyclic pile testing programs which are collated in this paper. General trends are established through comparison of the tests within the database and the conditions where cyclic loading is most likely to be a concern are identified. In particular, loading conditions which involve full plastic shear reversals are seen to cause the most extreme cyclic damage, with the degraded capacity as low as 31% of the precyclic static capacity. The underlying mechanisms which can result in cyclic damage are explored, with particular attention given to the pore pressure response, radial stresses, shear transfer and particle reorientation.

Jan 1, 2009

Stellite-6 coatings were formulated on two Ni-base superalloys, namely Superni 75 and Superni 600, by a shrouded plasma-spray process, and the oxidation behaviour of these coatings has been investigated in air and in an aggressive environment of Na2SO4- 60%V2O5. Accelerated oxidation tests were conducted in a silicon-carbide tube furnace under cyclic conditions at an elevated temperature of 900°C for 50 cycles. Each cycle consisted of 1 h heating and 20 min cooling in air. A thermogravimetric technique was used to approximate the oxidation kinetics. The corrosion scales were characterised by XRD, SEM/EDAX and EPMA analysis. It has been observed that the coatings nearly followed the parabolic rate law of oxidation. Overall weight gain conceived in air was just 51% of that in the aggressive environment in the case of coated Superni 75, whereas in case of coated Superni 600, the cumulative weight gain in air was found to be one-third of that in the Na2SO4-60% V2O5 atmosphere. Furthermore, the coating showed very good adherence to both of the substrates during the course of air oxidation, whereas some superficial cracks were observed near the edges of the specimens during the molten salt induced oxidation. XRD analysis revealed the presence of phase-like CoO, CoCr2O4 and Cr2O3 in the oxide scales, which are reported be protective against high-temperature oxidation. The XRD results were further supported by SEM/EDAX and EPMA.

Jan 1, 2005

By W. Choi

The present study revealed that the bioleachability of a chalcopyrite flotation concentrate is influenced by the semiconductor properties of CuFeS2. The overall reaction of biooxidation,

Jan 1, 1991

By C. -S. Jiang

In most copper refineries, addition agents are added at predetermined rates with no further monitoring of their activity or concentration in the electrolyte. Increasingly stringent cathode quality requirements, and a desire for better process control in tankhouse operations, have recently directed a number of refineries to search for a better addition agent control strategy. Extensive development work has been carried out at the Noranda Technology Centre for the monitor in of glue and thiourea in copper refinery electrolyte using cyclic voltammetry (cv~. Data from both synthetrc and commercial electrolytes are presented, showing the ability of CV to produce reliable and easily identifiable fingerprints of addition agent concentrations in copper refinery electrolyte.

Jan 1, 1991

By A. G. B. Hayes, C. L. Renzoni

"AbstractThis paper provides a rough outline of economic expectations for the near future and then goes on to discuss their effect on the expected demand for metals, using zinc, copper, nickel and aluminum as detailed examples.IntroductionMINING, as you are all painfully aware, is a cyclical business. We believe that it will remain so as long as there are economic cycles.The fortunes of the industry are tied to those sectors of the economy where decisions can be postponed until more favourable times: automobiles, housing, appliances, inventory building and capital spending. Over the past two years, while U.S. GNP fell by 3.8%, automobile production declined by 31 %, from 9.7 million units in 1973 to 6.7 million in 1975. Housing starts plummeted some 43% from 2.1 million units in 1973 to 1.2 million in 1975. Little wonder that U.S. copper consumption fell by 37% and zinc consumption by 38% over the same period.With the rest of the world's economies moving in unison with that of the United States, it is also not surprising that times have been tough for mining.Arthur Burns, chairman of the U.S. Federal Reserve, contends that each recession sows the seeds of its own recovery. The worse the recession, the better the subsequent recovery. If this is true, then the lot of the mining industry should improve significantly over the next two to three years."

Jan 1, 1977

By Roy A. Grancher

CYCLING WITH CEMENT "THE WHEEL IS COME FULL CIRCLE" Shakespeare's King Lear Act V, Scene 3, Line 176 The time clock of the cement industry has been turned back to the early 1950s. After the trials and tribulations of the decade of the Sixties, the hands now stand where they did just over twenty years ago. Cement shipments have steadily increased, with a record 419 million barrel level (78.8 million tons) being reached last year. Plants are operating at average utilization rates in excess of 85 percent of rated capacity. The spread between supply and demand has narrowed to where a definite shortage of cement now exists within the industry. The notable and unfortunate difference between the two periods however is that, back then, cement's returns were a respectable 14 to 18 percent, whereas today they stand at less than half those levels. Insufficient return forms the present foundation of the U.S. cement industry. This lack is destined to have a cumulative effect. Just as the industry's balance between supply and demand is returning to favorable proportions, promising a period that has historically and now should generate those profit levels required to modernize and provide for capacity addition, cement instead finds itself frozen by federal price controls into the semi-depressed condition that has existed for over a decade and from which it was just starting to emerge. Capital is not attracted to continued low returns, and increasingly restrictive pollution control measures are necessitating great non-productive expenditures be made as definite costs to stay in business. Even a clouded crystal ball would reveal that additional cement plant closings can be expected.

Jan 1, 1972

By P. R. Taylor

Recent research by the investigators has evaluated the oxidation roasting of refractory gold concentrates in the presence of hydrated lime. (Taylor, 1990, 1991, 1992, 1993). These results have indicated that it may be possible to roast concentrates in such a way as to contain nearly all of the sulfur and arsenic in the roaster calcine and that cyanidation may be possible. To further evaluate the behavior of this type of roasting system a laboratory cyclone reactor was built and operated using pyrite and hydrated lime as a .model system. Approximately 50 years ago, the principle of cyclone firing entered practical boiler construction. The appeal of the cyclone configuration was that it afforded the flash combustion process greater efficiency due to turbulence-induced increased mass transfer, heat exchange, and combustion rates.

Jan 1, 1994

By Norman A. Jull

"IntroductionThe scope of this paper is intended to deal mainly with cyclones in grinding circuits. However, the section on Cyclone Equipment, contains more general descriptions, to cover most of the cyclones used in mineral separation plants.Cyclones as heavy media separation vessels are discussed by Mark Freberg (this volume). Their use in tailings deslirning is discussed by P.C. Lighthall, eta/. (this volume).Cyclone EquipmentCyclone TerminologyApexObviously, the apex of a cone is the smallest end. However, with cyclones the term is usually used for the fitting which is attached there to control discharge of the underflow stream.Note that the cyclone need not be so mounted that the apex is the lowest point, although that is the most common method. Keeping the apex below the rest of the cyclone helps avoid plugging when the underflow contains very large particles and the tonnage of underflow solids can fluctuate.Various devices for adjusting apex diameter or otherwise controlling the underflow are discussed later under ""Cyclone Construction"".BypassingThe transport of a portion of feed slurry directly to underflow so that classification is bypassed by that portion of feed.This action is fundamental in any hydraulic classification, whether gravity or centrifugal, because the large particles going to underflow have some void volume between them, which remains filled with feed slurry.D50By definition, D50 is that particle size which has an equal probability of going to overflow or to underflow.It is calculated by drawing a curve of recovery vs particle size and noting the size at which 500Jo recovery occurs.This may be done equally with corrected or with gross recovery (see below) and the resulting value should therefore be identified as d50c (corrected d50) or as d500 (gross d50).Note also that it is common in industry practice to plot size analysis data on the retained size rather than on the average of passing and retained (the middle of the size band). To portray sizing alone it makes no difference, but to read a D50 value off a curve of corrected or gross recoveries, it is essential to plot those values on the average size of each band."

Jan 1, 1989

By E. S. Allen, P. R. Kruesi, J. L. Lake

An electrochemical process is described for converting concentrates of base-metal sulphides to the corresponding pure metals and elemental sulphur. The application of the process to chalcopyrite is discussed. The process is also of potential interest in processing copper-nickel sulphides, and laboratory data concerning this potential are presented. The process creates neither air nor water pollution.

Jan 1, 1973