Search Documents

By Hector O. Romero, Paulo C. Fernández A, Christian Rees Prado, Claudio C. Gajardo

In open-pit mining, estimating post blasting displacement and spillage accurately is essential to guarantee operational efficiency, ensure alignment with production plans and their associated key performance indicators. The absence of predictive modeling tools on blasting operations results in several critical challenges, including operational reworks due to deviations in material displacement, significant discrepancies between mine and plant (ore grade dilution included), misalignment with the reported production plan, and increased operational costs due to inefficient use of resources. This study, conducted at Los Bronces Mine operated by Angloamerican, Chile, addresses the application of a three-dimensional simulation tool that, through numerical modeling, is capable of predicting post blast rock displacement. The implementation was carried out in a pit phase characterized by blasts near the pit boundaries, with a high risk of material spillage and potential blockage of the only access ramp to the extraction levels. By the integration of key design parameters, such as blast pattern geometry, detonating time, explosive charge distribution and pre and post blast survey, an optimal calibration was achieved and validated in seven blasting events to date, reaching an accuracy greater than 80% in estimating post-blast rock displacement and spillage volumes. Furthermore, this study allowed the evaluation of different pattern alternatives with and without spillage mitigation measures (use of air decks near the free face), obtaining a high correlation and accuracy exceeding 95% in predicting the selected design outcome, supporting optimal design selections. The result highlights the usefulness of the model as a decision-support tool for blasting engineers and short-term planning, by reducing the need for unnecessary operational reworks, improving geological and operational reconciliation, and ensuring the alignment of the extracting plan with production targets. The current average deviation is 15%, with higher deviations observed in blasts with smaller volumes of spill or where the simulated sequence was changed before blasting. The use of this type of three-dimensional numerical modeling represents a significant advancement for blast engineering and the optimization of key performance indicators in open-pit mining operations.

Jan 26, 2026

By V. R. Manukonda

Selective flocculation of iron ores is extremely sensitive to the type and the amount of soluble salts in pulp solutions. Chemical precipitation of alkaline earth ions combined with ultrasonic treatment deactivates their adverse effects without using any environmentally ill-defined reagents. The manner in which ultrasonic treatment affects starch adsorption on hematite, dissolution of quartz, and selective flocculation process was investigated. Selective flocculation tests were conducted in the presence of up to 400 ppm calcium ion on a quartz-hematite mixture by precipitation as calcium carbonate, and the role that silicate ion generated by ultrasonic treatment plays in achieving the selectivity of separation is discussed.

Jan 1, 1987

By Raja V. Ramani

Worldwide, promulgation and enforcement of health and safety laws and regulations have been the primary means of ensuring minimum and uniform standards of health and safety in the mining industry. In U.S. coal mines, a new era was ushered-in in 1969 for the control of health hazards from respirable coal mine dust. Since then significant progress has been made on all aspects of the respirable dust problem-its definition, monitoring, reduction, and control. In the intervening years, our ability to monitor, analyze, and characterize the mine atmospheric environment and the health of miners has increased many fold. Also, advancements in production technology have far outdistanced enhancements in environmental control technology. Therefore, questions are continuing to be raised on the adequacy of the characterization and control measures with regard to both the airborne respirable dust in mines and the health effects of respirable dust. Late in 1995, the Secretary of Labor appointed an Advisory Committee on the Elimination of Pneumoconiosis Amona Coal " Mine Workers (Dust Advisory Committee) to review the progress towards elimination of coal worker's pneumoconiosis (CWP) and silicosis, and in the program to control respirable coal mine dust in underground and surface mines, and make recommendations including improved standards and other appropriate measures for the control of exposure to airborne coal mine dust. The Committee's report was released in October, 1996. In this paper, a summary of the recommendations of the Committee is presented. A brief discussion of the background, and the issues and findings leading to the recommendations is also presented. The Committee concluded that the progress made towards making mines safer from the health hazards of respirable coal mine dust is substantial but that it is not sufficient to achieve the intent of the 1969 Coal Act. The Committee's recommendations encompass a wide range of issues addressing permissible exposure limits (PELS), sampling, dust control plans, hazard and medical surveillances, role of miners, training, and research and development.

Jan 1, 1997

By T. S. Spicer, C. C. Wright

A CHARACTERISTIC property of bituminous coal is that upon being heated the coal becomes plastic, evolves volatile gases, and finally solidifies into coke This fundamental characteristic is of utmost importance and is utilized in the production of the high-temperature coke upon which the steel industry is so dependent, but from the standpoint of operation in the domestic underfeed stoker this coking tendency seriously interferes with efficient combustion When the coke formed has too strong a structure, certain difficulties result, such as low rate of burning, slow response to heat demand, and, in extreme cases, extinction of fire The plastic mass prevents uniform distribution of air through the fuel bed and, With strongly coking coals, large dense pieces of coke are produced which have much less reacting surface thin was possessed by the original coal In both ignition and combustion of solid fuels, the extent of the reacting surface is an accelerating factor Poor combustion permits a surplus of fuel to accumulate in the furnace because the rate of feed and the rate of combustion are not in equilibrium, and this produces an unbalanced condition detrimental to continued) automatic service In order to burn strongly coking coals satisfactorily in a conventional stoker during the three requisite types of operation continuous, intermittent and hold-fire, frequent attention is necessary Domestic stokers are defined by the industry as residential stoker heaters that burn 60 lb of coal or less per hour With a few exceptions, these units employ the underfeed principle of combustion in which both air and coal move in the same direction up and through the fuel-bed Domestic combustion equipment has difficulty in meeting the problems presented by the several variations in ash and volatile matter, in ash-clinkering tendencies, in coking properties, and in the particle size of bituminous coals The work of Bituminous Coal Research Inc at Battelle Memorial Institute has shown that, of these, coking characteristics and the clinkering tendencies have the greatest effect upon the operation of the conventional clinkering type of stoker Typical coke formations in a clinkering type of underfeed domestic stoker are illustrated in Fig. I, which shows (A) the ideal fuel bed obtained with a noncoking or free-burning coal, (B) the type of fuel bed formed -with, a coal that produces a weal coke, and (C) the type of fuel bed obtained with a strongly coking coal C is characteristic of the fuel bed developed when the average Pennsylvania bituminous coal is ,burned in an underfeed stoker of conventional type It is apparent from these pictures that the formation of coke trees will seriously interfere with the efficient automatic combustion of Pennsylvania bituminous coals

Jan 1, 1942

By J-C. Lv, S. Zhao, F-L. Zhang, T. Yan

"To eliminate nozzle clogging during continuous casting of ship plate steel and reduce the calcium addition required, the composition of CaO-MgOAl2O3 inclusions in the liquid phase region must be controlled. Thermodynamic calculations using FactSage show that when the balanced Al content is 0.03 mass %, aCa in the liquid steel is 1–10 ppm, and aMg is 0.01–0.3 ppm; and when the balanced Al content is 0.06 mass %, aCa in the liquid steel is 1–30 ppm, and aMg is 0.05–0.9 ppm. The CaO-Al2O3-CaS inclusions can be controlled in the liquid region below 1600°C at aCa values of 5 ppm, 15 ppm, and 30 ppm, and the balanced Al content should be controlled in the range of 0.001–0.050, 0.005–0.250, and 0.010–0.50 mass %, respectively. Based on theoretical analysis, the refining slag composition should be controlled to 45–53 mass % CaO, 30–37 mass % Al2O3, 6–12 mass % SiO2, and 6–8 mass % MgO. Optimization of the slag system and steel composition can reduce, or even eliminate, the requirement for calcium treatment. The total oxygen content in the slab can be controlled to 15–21 ppm, with typical micro-inclusions ??10 ??m in size, with compositions in the CaO-Al2O3-MgO and CaO-Al2O3-CaS systems. Introduction With the rapid growth in steel output in China and the changes in the macroeconomic environment, competition in the steel industry has become more intense. The technology for economical cleaning of high-grade steel is important for improving product quality and reducing production costs. However, the functions of refining equipment have not been fully taken into consideration, and the combination of refining methods has not been optimized completely. These problems have become a bottleneck, restricting modern steel enterprises from developing an economic clean steel production process. Ship plate steel produced by the converter long process has been selected as the example in this study. The composition of the steel is shown in Table I. This steel is a high-strength low-alloy steel for rolling media and heavy plates, mainly used for ocean-going vessels and other steel structures. The carbon content in the steel is far from the peritectic point, and the crack sensitivity of the slab surface is weak, so impurities and gas content are strictly limited. Therefore, the process route BOF (basic oxygen furnace) – LF (ladle furnace) – CC (continuous casting) needs to be studied."

Jan 1, 2018

By C. L. McKenzie

American Girl Mine is located in the Cargo Muchacho Mountains in the southeastern Imperial Valley of Southern California. Production from the current open pit mine and heap leach recovery system began in early 1989. Previous mining and gold recovery took place commencing in 1987 at the Padre Madre site, situated adjacent to the American Girl site to the southwest. In mid-1990, a 790-tonne-per-day underground gold mine and mill went into production. Approximately 6,500 troy ounces of gold per month are recovered from the combined open pit underground mine operation. Copper in the form of Azurite [Cu3(CO3)2(OH)2] and Malachite [Cu2CO3(OH)2] are abundant in the mined ores (Henshaw, 1942). The high solubility of these minerals in caustic cyanide solutions has a negative impact on carbon adsorption and electrowin processes. This paper presents the results of monitoring programs, process chemistry, and control changes introduced at American Girl Mine to abate production complications in the refinery and measures taken to minimize solution gold losses in the adsorption circuit(s).

Jan 1, 1993

By U. Srivastava

In the processing of manganiferous ore, it is useful to control whether the manganese (Mn) goes to the iron product to produce ferromanganese, or to the slag for extraction as a high Mn product. This can be done by manipulating the thermodynamic conditions for manganese oxide(MnO) reduction to control whether it remains as MnO or converts to metallic Mn. Results are presented showing that during production of iron nuggets, reduction of manganese oxide (MnO) can be controlled by changing the furnace temperature and reductant composition appropriately.

Jan 1, 2010

By S. Shairp

The first commercial application of the Dynatec two-stage zinc pressure leach process commenced operation at the metallurgical complex of Hudson Bay Mining and Smelting Co., Limited in Flin Flon, Manitoba in 1993. A key feature of the successful leaching operation is the presence of iron in solution, which facilitates oxygen transfer in the autoclaves and enables rapid oxidation of zinc sulphide minerals. At the same time, the solution from which zinc is recovered must be essentially iron free. Precipitation of iron from the solution starts in the autoclaves and is completed in subsequent atmospheric purification steps. Conveniently, these iron precipitation steps also remove nuisance elements such as arsenic and fluoride from the solution, while producing solids with good liquid-solid separation characteristics. This paper provides an overview of the current operations in Flin Flon, with particular reference to the behaviour and deportment of iron throughout the zinc plant.

Jan 1, 2006

By T. C. Murray

An automatic control system was recently installed to insure the continuity of operation between the ship docking and ore handling facilities and the computerized conveyor-fed sintering plants and blast furnaces. Although the basic concept for material handling has not changed, many innovations including computer control have been implemented.

Jan 1, 1978

By Ernest F. Giovannitti

A couple of years ago, one of the major television networks produced a series on the environment. One episode in the series dealt with the nation's solid waste problem and some of the research being done to solve it. It was interesting to listen to one researcher who was attempting to develop a glass that when broken would dissolve in water. It was said that using this glass would eliminate over 100 million tons of solid wastes each year. At first glance, it would appear that this research-effort would make a significant contribution to environmental pollution control; however, if one pauses to consider the water, he can see that this solution to the solid waste problem may well contribute to a water pollution problem. The dissolved material must either end up in our surface streams or be removed in waste treatment systems. Either alternative may have a more adverse effect on the environment than the original problem. With today's emphasis on the environment, it is important that the effects of our activities be studied in depth. Then, by properly planning the activity, the adverse effects can be minimized. The coal mining industry 100 years ago was in the same boat, as our glass maker, is today. Unfortunately, it too failed to consider all the effects of its activities and as a result, in Pennsylvania, there are over 5000 miles of streams adversely affected by coal mine drainage. The situation is improving, however, because mine operators are beginning to recognize and accept the methods for controlling coal mine drainage. The purpose of this paper is to discuss the measures for the control of coal mine drainage and to set forth the factors that affect these controls.

Jan 1, 1972

By C. P. Proctor, E. D. Hummer, J. A. Younkins

COMPARATIVELY little has been published relating practical experience with the control of the solid content of washery water systems that must be "closed." A "closed" system is one that for some reason may not be cleaned by the emission of any effluent of high solid content to be replaced by clean water in order to hold the solid content of the waste water within reasonable bounds for efficient washing. It is the purpose of this paper to describe practical experience with such a water system and to present data that it is hoped may be of some use to those who are faced with a similar problem. The washery clarification system described comprises three thickeners and three filters, and although it is admitted that each of the fields of water settling and thickening and filtration offers a wide scope for investigation, the authors are not attempting to present the answers to these problems but to set down the results of some experience along these lines, making no claims as to the ultimate solution of the problems in hand. The subject of water clarification has vast ramifications; for example, the science of flocculation as applied to water settling and filtering opens up fields of wide possibilities of which as yet little is known. A comparatively recent entry into the field of water treatment, which may offer possibilities of practical application, is the use of "wetting" agents such as "Aerosol." GENERAL ARRANGEMENT OF WATER SYSTEM So that the reader may obtain a comprehensive picture of the factors concerned in the control of a closed water system, it is necessary to give a brief description of the washing plant that is serviced by the water system to be described in the following pages. As we are not primarily concerned with the washing plant in detail, only a brief description of the flow of coal as it relates to the water system will be given here. For a more detailed account of this type of washer, the reader is referred to earlier papers.1.2 The washer, which handles 0 to 4-in. raw coal (750 tons per hour) is an American Rheolaveur plant of two complements; the coarse coal or sealed discharge plant and the fine coal or free discharge plant. The sealed discharge plant (Fig. r) consists of twin 48-in. primary launders, each having two washing boxes, supplemented by one 32-in. rewash launder, which also has two washing boxes. "Push" water for washing and conveying coal in these launders is supplied from a constant-head tank under pressure head of 10 ½ ft. at the point of introduction at the feed end of the launder. This tank also supplies water for upward or vertical currents used in the Rheolaveur or washing boxes. Each box discharges into a sealed boot elevator (Fig. I).

Jan 1, 1942

By Pier-Olivier Devin, Daniel Hodouin, Maryam Sadeghi, COREM, Claude Bazin, François Lavoie

"Spiral concentrators are used for processing coal and heavy minerals such as it is the case for the concentration of iron oxide from light silica gangue. The concentration process for iron ore usually consists of a rougher bank of spirals followed by two stages of spiral cleaning. The process control applied to the concentration circuit aims at maintaining a target iron content of the final concentrate and is mainly conducted by adjusting the wash water addition and the position of the splitter gates at the discharge of the spiral. This paper describes the use of a simulator to study control strategies for a gravity concentration circuit using spirals.INTRODUCTION The Canadian iron ore mines are located in the Northern part of Quebec and in Labrador (Neal, 2000). These iron ores consist mainly of hematite with some ore bodies rich in magnetite and ilmenite. The processing of the coarse hematite iron ore consists of the extraction from an open pit mine, followed by the conventional crushing and autogeneous grinding of the ore to obtain a particle size smaller than 1.2 mm. The ground ore assaying 40% hematite (Fe2O3) with quartz (SiO2) as the main gangue is processed by spirals to produce an iron oxide concentrate assaying 90 to 95% hematite.Spirals separate the particles according to their specific gravity and size (Burt, 1984; Bazin et al., 2014). These environment friendly devices have been used for decades and are still used for the preparation of coal and for the concentration of heavy minerals such as iron oxide (Staff, 1977; Wills, 1992). However very little information is available concerning the control of gravity concentration circuits. This paper analyzes the control practice of a gravity concentration circuit using a simulator. The paper consists of 3 sections. The first section describes the operation of spirals and spiral concentration circuits. The second section briefly describes the simulator and shows some simulation results for a gravity concentration circuit. The third section shows the application of the simulator for the study of control strategies for a spiral concentration circuit."

Jan 1, 2016

By B. Das

Most coals are susceptible to spontaneous heating which in turn creates problem to mining, storage and transportation of coal. It is impossible in actual practice o eliminate spontaneous heating but spontaneous combustion can effecively be controlled through a clear understanding of its mechanism and the factors affecting it. There are altogether six stages in the process of spontaneous combustion. This includes the water adsorption stage and six oxidation stages: chemi-sorption (upto 70°C), decomposition of peroxygens (70°C-150°C), oxy-coal formation (150°C-230°C), combustion initiation (230°C) and active combustion (> 230°C). Heat is produced in all these stages. On the other hand heat is also dissipated so that some equilibrium temperature is reached. If this temperature exceeds a certain critical value (generally about 70°C), coal oxidation may advance to spontaneous combustion. The major factors influencing spontaneous combustion of coal are: coal rank, maceral composition,, water, mineral matter, joints and fissures, seam depth and thickness, mine Layout, method of ventilation, etc. Susceptibility is high for low rank coals and generally decreases with increase in rank. Of the macerals, the exinites are generally most susceptible, the inertinites least and the vitrinites somewhere in between. Water plays a major role on the spontaneous heating of coal, assisting in someways and inhibiting in other. Unrecovered coal in the gob (generally in thick seams) is a major source of fire hazards and this is specially important in shallow mine. Proper design of mine ventilation system can substantially reduce the risk of mine fire. Panel layout and load transfer can affect the development of induced cracks which in turn influence spontaneous heating. Finally, the difference between the spontaneous heating of coal in a seam and that in storage or transportation is mainly due to the change in moistured content, air circulation through the coal and coal fragmentation. These aspects have been analyzed in this paper with a view o reducing the risk of spontaneous combustion.

Jan 1, 1986

By John W. Tieman

The increasing magnitude of our nation's pollution problems seems to stem from two main factors: urbanization and technical advance. In 1920, less than half the country's 106 million people lived in cities. Forty years later, the urban population accounted for 70 percent of the nation's 179 million. It is predicted that by the end of the century, 95 percent of the U. S. population, estimated at 280 million, will live in urban areas. As these people live increasingly in city concentrations, their residues also concentrate. With technological advances to support the increasing population, the variety and quantity of goods that we use also increases. New materials and processes result in increases in pollutants, some of them new. The harmfulness of these pollutants is sometimes known, but sometimes only suspected. One pollutant of concern at the present time is sulfur dioxide, the product of combustion of sulfur-containing fuels. Research on processes to remove sulfur oxides from flue gas has been in progress for many years. Pioneers in this field were the British who, in the early 1930's, installed a full-scale flue gas scrubbing unit on a 120 MW boiler using alkaline water from a Thames estuary plus chalk. Since that time, various methods have been studied by many investigators. Federal laws covering air pollution started with the 1955 Air Pollution Control Act. With the advent of the Air Quality Act of 1967, and subsequent publishing of criteria and available technology for control of sulfur oxides in January 1969, the clamor for information on commercially available control techniques to remove sulfur from fossil fuels has rapidly increased. Although many state-of-the-art papers have deluged the literature during the past several years, the research going on in the area of sulfur oxides control is of such importance that periodic reviews are justified. It is the purpose of this paper, therefore, to again review the state-of-the-art, but this time from the stand-point of what is immediately commercially available

Jan 1, 1972

By J. W. Smith, J. Van Dusen, A. Papachristodoulou

"As part of a study to evaluate factors affecting tankroom air quality, the mechanism of aerosol generation from bursting bubbles in electrowinning operations has been investigated. Typically 2 to 3 mg/m2.s are produced in zinc tankrooms. Analysis shows that the rate of production of film drops (geometric mean diameter - 2 urn] increases with decreasing bubble size, and that jet droplets (geometric mean diameter - 20 um) are not produced with gas bubble larger than - 4 mm. Both mechanisms of drop formation and current efficiency are affected by surface active agents, with an over-all reduction in emission of up to 60% to 70% being achievable. A source control system which does not adversely affect electrolyte properties is always preferred, and coalescence of all gas bubbles in to a continuous stream of gas at a single point on the electrolyte surface would eliminate aerosol emissions. This objective was the basis for design of a coalescence device which, in laboratory tests, reduced the emission rate by over 95%.The control device fit s over the electrodes in the electrowinning cell and is partially immersed in the electrolyte. A number of changes in the design which resulted in significant improvement in the performance of the device are reported.Field tests have shown that only about 75% of the aerosol below 10 um can be eliminated by coalescence. The remainder (up to 95% of the total) is controlled by coalescence of droplets, by impaction on the exposed collector surface and gravitational settling.The device does not interfere with operation of the tankroom, handles the effect of surges in power during harvesting, and is simple and inexpensive to maintain. IntroductionDuring the electrowinning of metals (such as zinc and copper) gases are evolved along the electrode surface forming small bubbles. The bubbles travel upwards and burst on the electrolyte free surface generating, in this way, small droplets. Because the electrolyte is often highly acidic or contains toxic materials, the whole process can result in the formation of an aerosol in the atmosphere above the electrowinning cells which poses a serious health hazard to workers in the area, and corrodes equipment."

Jan 1, 1988

By Fulian He, Jianhang Chen, Dongdong Chen, Shoubao Zhang

"The Wangjialing Coal Mine is the main colliery of the China Coal Huajin Energy Limited Liability Company. The average thickness of the coal seam in District 201 is 6.21 m. Fully mechanized longwall mining was used in this district. The ventilation roadway of panel 20102 was influenced by the retreat mining of the adjacent panel 20104. Therefore, large deformation and severe roof falls occurred in this roadway, seriously influencing the safety production of this coal mine. To support the roadway, cable truss was proposed to strengthen the reinforcement of this ventilation roadway. First, numerical simulation was used to optimize the reinforcement parameters, including the cable installation angle, cable length, and eccentric distance. Based on numerical simulation results, in-situ tests were conducted in the ventilation roadway of panel 20102 with the cable truss technology. In-situ monitoring results showed that the roof-to-floor convergence and the convergence of roadway on two sides were within the safety range. Furthermore, no apparent separations occurred in the roof. These indicate that based on the designed parameters, the cable truss system can effectively maintain the roadway stability under the severe influence of the adjacent longwall mining.INTRODUCTIONCable bolts are flexible tendons composed of multi steel wires, which are wound into a strand (Chen, Hagan, and Saydam, 2018). They were initially introduced in the hard rock mining industry in the 1960s. Later, they found rapid application in coal mines to maintain the stability of excavations (Wang et al., 2015).The standard cable bolt is composed of seven steel wires with a diameter of 15.2 mm. Laboratory and in-situ tests showed that there is a low bonding capacity between the standard cable bolt and the grout (Craig and Holden, 2014; Chen, Hagan, and Saydam, 2018). Then, modified cable bolts are developed based on the standard cable bolts. They are improved by changing the surface geometry of standard cable bolts, such as birdcaged cable bolts (Hutchins et al., 1990) or nutcaged cable bolts (Hyett et al., 1993). Further tests proved that modified cable bolts have better mechanical interlock and friction between the cable bolt and grout, leading to larger load transfer capacity of cable bolts.Although cable bolts have been used for many years, failure of the cable bolting system still occurs. A common failure mode is the damage of surrounding confining medium while the cable bolt is still hanging in the roof, which is caused by the bond failure of the cable/grout interface (Hutchinson and Diederichs, 1996). To prevent the cable bolting system from failing, the cable truss system is more widely used in mining engineering."

Jan 1, 2019

By Fuqiang Zheng, Yufeng Guo, Pengfei Li, Guanzhou Qiu, Tao Jiang, Andrew Yakovlevich Travyanov

Low content of TiO2 and high impurities content of Ca and Mg are the shortcomings of domestic ilmenite. To meet the requirements of the material in the titania produced by chlorination process and titanium sponge industry, enrichment of ilmenite is necessary. In the process of enriching ilmenite, high temperature and reductive condition were beneficial to the formation of anosovite, but the high content of magnesium oxide which was solid soluble in anosovite baffled the following separation. So the effects of pre-oxidation and reductive conditions including reduction temperature, reduction time and hydrogen concentration on the phase composition and metallization rate were studied. The characteristics of reduction samples were analyzed by X-ray diffraction and optical microscope. Results have shown that the reduction product is mainly composed of Fe, Fe(Mg)TiO3 and TiO2 at 1123K, its metallization rate is about 65%,magnesium exists in Fe(Mg)TiO3.

Jan 1, 2015

By Earl Hanson

FIRES in heavily timbered mines are disastrous, involving danger to both life and property. Some mines have been completely ruined or so heavily damaged that reopening them would not pay. Though few mines are entirely free from danger of fire, the risk is minimized by proper care and good design of plant. The Tintic Standard mine is at Dividend, Utah, in the famous Tintic mining district, about 60 miles south of Salt Lake City. The development of the mine was begun in 1907 by the late Mr. E. J. Raddatz and his associates. From the beginning, the work was hampered by high rock temperatures and the presence of high concentrations of rock gases such as carbon dioxide and nitrogen. Development work was carried on with great perseverance for nine years, and resulted in the discovery of ore in 1916. The total production of the Tintic Standard mine to Jan. 1, 1936, amounted to 1,664,388 tons of ore, having a gross value of .$61,996,719.

Jan 1, 1936

By Humberto Tronconi Coelho

The use of friction dampers are wide proposed for a variety of mechanical systems for which it is not possible to apply viscoelastic materials, fluid based dampers or others viscous dampers. An important example is the application of friction dampers in aircraft engines to reduce the blades vibration amplitudes. In most cases, friction dampers have been studied in a passive way, however, a significant improvement can be achieved by controlling the normal force in the contact region. The aim of this paper is to study four control strategies for friction dampers based on three different hysteresis cycles. The first control strategy maximizes the energy removal in each harmonic oscillation cycle, by calculating the optimum normal force based on the last displacement peak. The second control strategy combines the first one with the maximum energy removal strategy used in the smart spring devices. Finally, is presented the strategy which homogenously modulates the friction force. Numerical studies were performed with these four strategies defining the performance metrics. The best control strategy was applied experimentally. The experimental test rig was fully identified and its parameters were used for numerical simulations. The obtained results have shown the good performance for the friction damper and selected strategy, also, the agreement between numerical and experimental results.

Jul 31, 2018

By Michel Ruel

"PID loops – also known as base layers or regulatory controls – form the foundation of any plant’s control layer and it is generally accepted that PID loop health has a direct impact on the plant’s bottom line. Keeping these thousands of control loops in good health has a direct impact on the plant’s bottom line: it reduces variability, improves quality and throughput, and decreases energy costs and raw material usage. This has been well proven and documented in many articles. In the last ten years, technology has evolved: control engineers can now keep track of control loop performance and link it to the root causes of variability. However, they lack industry-wide best practices and criteria for determining what can be considered as excellent, good, fair, or poor performance. To ensure that PID control loops continue to perform well and meet their objectives, control engineers need a combination of (a) an appropriate monitoring technology and (b) best practices for doing the maintenance of base layer controls.Most plants have limited resources and operate with an increasing number of constraints; therefore, using the right tools and including reports in daily workflow is key for success. This paper suggests roles and responsibilities of key players needed to work toward control performance best practices and discuss organisational changes to succeed.INTRODUCTIONAlthough PID controllers are reliable workhorses in the process industry, they are often underrated. Since the 1980’s, computer control has evolved and the control algorithms used by control engineers have become increasingly complex. However, PID controllers still handle over 90% of the control loops in operating plants. Table 1 shows the savings that can be realized by achieving best-practice in several different process control categories (Brisk, 2004). The savings are expressed as a percentage of production costs."

Jan 1, 2011