Search Documents

By W. W. Adams

In mining coal, the Nation's principal mineral fuel, loss of life has been much lower recently than in earlier years when coal mining contributed so heavily to the industrial-accident death toll in the United States. Particularly notable has been the relatively small number of deaths during the past few years compared with the number that occurred 20 or 30 years ago. Reports received by the United States Bureau of Mines, covering all commercially operated mines that were active during all or any part of the calendar year 1935, showed that accidents during that year had resulted in the loss of 1,242 lives. This death toll, although regrettable, represents a material improvement over the industry's experience during most years prior to 1935, and especially over the industry's worst year, 1907, when 3,242 men were killed. Fewer lives were lost in 1933, when 1,064 men were killed at work, than during any year for which complete figures are available.

Jan 1, 1938

By W. W. Adams

The accident-prevention record of the coal-mining industry in the United States was more favorable in 1936 than in 1935, both from the standpoint of the relative safety of the individual miner on the job and of the price in life and limb that the Nation paid for its year's supply of coal. The increase in relative safety of the individual miner was indicated by a lower death rate and a lower injury rate than in the preceding year per million man-hours of exposure to the hazards of mining; that is, per million hours of work performed by the employees. (See table 1.) A reduction in the price in life and limb that the Nation paid for a year's supply of coal was indicated by a smaller death rate and a smaller injury rate per million tons of coal produced. Thus the individual miner was a better insurance risk, as far as accidents were concerned, in 1936 than in 1935, and a ton of coal used in the homes and industries of the country represented less human suffering than in 1935. The two points of view are distinct, and both should be kept in mind when considering accidents and safety in coal mining or in other industries. More men were employed in 1936 than in 1935, and more workdays were available for the individual miner. Large gains were also made in the total number of man-shifts and man-hours worked in the industry as a whole. In number of tons of coal mined, 1936 showed large gains over 1935. Moreover, the average output of coal per man-hour worked was higher in 1936 than in 1935. All of these gains were made without lengthening the average number of hours of work per man per day.

Jan 1, 1939

By W. W. Adams

Coal mining in the United States, had a somewhat higher death rate per million man-hours of exposure among the employees in 1937 than in 1933 to 1936. However, the rate in 1937 was lower and therefore more favorable than that in any year since 1921 but previous to 1933. The nonfatal injury record, which began in 1930, was lower and therefore better in 1937 than in any other year since 1930. Separate figures covering bituminous-coal mines in all States showed a lower fatality rate in 1937 than in any year since 1920 but before 1933, and a lower nonfatal injury rate than that of any year since 1930 except 1933 and 1936. Reports for anthracite mines in Pennsylvania revealed a better safety record for fatal accidents in 1937 than in any year since 1930 except 1933, 1934, and 1936 and a better record for nonfatal injuries than in any year since 1930 except 1933.

Jan 1, 1940

By W. W. Adams

Every man-hour of work performed in and about the coal mines of the United States had a 2-percent heavier death load from accidents in 1938 than in 1937. This is an unorthodox way of stating that the death rate per million man-hours of exposure or employment was 2 percent higher in 1938 than in 1937, increasing from 1.74 to 1.78. Thus the average miner had a 2-percent greater chance of being killed in 1938 than he had in 1937. The average quantity of coal resulting from 1 man-hour of work increased 3.6 percent -from 0.615 ton in 1937 to 0.637 ton in 1938. The production of the average ton of coal was accompanied by a slightly smaller loss of life in 1938 than in 1937, the accident rate being 2.793 per million tons in 1938 compared with 2.833 in 1937.

Jan 1, 1941

By W. W. Adams

Coal mining in the United States established a good safety record in 1939. The death and injury rates per man-hour of exposure to risk were favorable compared with most previous years, and the number of persons killed or injured in proportion to the quantity of coal mined was also lower than in any other year for which figures are available. Moreover, productivity per man-hour was higher than ever before. The number of man-hours of work performed increased 9 percent over 1938, but there was a slight decrease in the number of men employed. Reports from operating companies showed 539,375 men employed during the year, and the period of operation averaged 179 workdays per man. Man-hours of work numbered more than 678 million. Accidents to the workers resulted in 1,078 fatalities and 54,015 nonfatal disabling injuries, causing disability of the employee for more than the remainder of the clay on which the accident occurred. For each million man-hours of exposure of the employees to mining hazards the fatality rate was 1.59 compared with 1.78 for 1938, and the injury rate was 79.65 compared with 82.61 for 1938. Production of coal averaged 0.661 ton per man-hour compared with 0.637 ton in 1938. The weighted average length of the workday was 7.03 hours or virtually the same as the previous year's average of 7.04 hours. Measured in man-hours, the average period of employment per man was 1,257 hours in 1939 and 1,147 hours in 1938.

Jan 1, 1942

By W. W. Adams

With production of coal per man-hour of work highest in history, the coal mines of the United States established a lower accident-frequency4 rate in 1942 than in any year since 1930, the first for which the Bureau of Mines, United States Department of the Interior, collected complete reports of nonfatal as well as fatal injuries. Reports from mine operators and State mining departments showed that 530,861 men were employed in and about coal mines during the calendar year 1942. This number does not include office employees or coke-oven workers. The figure represents a decrease of 15,831 men from the previous year, owing to losses of men to the military services and to more lucrative employment in the munitions and other industries. The loss of men was offset to some degree by an increase in the number of days of mine activity and the average number of hours of work per man during the year. The volume of work done during 1942 was 910 million man-hours, 11 percent more than in 1941. The average employee worked 243 days, 30 days more than in 1941. Production reached the unprecedented total of 640 million short tons, an increase of 12 percent over 1941; 582 million tons came from the bituminous fields of the United States and 58 million tons from the anthracite fields of Pennsylvania. To produce this quantity of coal 1,471 men sacrified their lives, and 69,564 men suffered nonfatal injuries that disabled them for more than the remainder of the day on which the accident occurred. The nonfatal injuries were divided into three groups: 65 caused permanent total disability, 2,045 caused permanent partial disability, and 67,454 caused temporary disability of 1 day or more but did not result in the loss of, or permanent loss of use of, any part of the body.

Jan 1, 1944

By W. W. Adams

The safety record established by the coal-mining industry of the United States during 1934, although not as favorable as that for the previous year, was better than the record for any other year during the period 1930-34 for which complete figures covering fatal and nonfatal accidents at the mines are available. The number of accidents was 89.98 per million man-hours of employment compared with 86.74 for the year 1933, the latter being the lowest rate in any of the 5 years referred to. The rate was 105.60 for 1930, the first year covered by available data. Employment increased in 1934; the number of workers represented an increase of 8 percent over the year 1933, man-shifts of labor increased 16 percent, and the number of man-hours of labor increased 7 percent. The total number of man-hours of employment also exceeded the number reported for 1932, and was almost equal to the record for 1931.

Jan 1, 1936

By W. W. Adams

With production of coal per man-hour of work at a higher level than ever before, the coal-mining industry of the United States established a near-record in lowering the accident rate of nonfatal injuries per million man-hours of exposure in 1940, the injury rate being lower, except for 1939, than in any year since 1930, the first year for which comparable figures for nonfatal accidents were collected by the. Bureau of Mines, United States Department of the Interior. The rate for fatal accidents, on the other hand, was not as low or favorable as in 1939, nor was it as low as in many years since 1910, the earliest year for which fatality rates were complete for all coal-mining States. Accident and employment reports received from mine operators and fatal-accident reports from State mining departments and inspectors showed that 533,267 men were employed at coal mules in 1940, exclusive of the number employed at coke ovens, Although this number represented 6,108 fewer employees than in 1939, a large increase was made in the volume of work performed and in the quan¬tity of coal produced. In 1940 the amount of labor performed at coal mines was 748 million man-hours, a gain of more than 10 percent over the previous year. The average employee worked 199 days, an increase of 20 workdays per man. Production of coal was nearly 513 million tons, an increase of 14 percent, of which more than 461 million tons was bituminous coal and more than 51 million tons was Pennsylvania anthracite. Accidents to mine workers caused the death of 1,388 employees; in addition, 59,781 employees were injured, and each injury resulted in disability of the employee for more than the remainder of the day on which the accident occurred.

Jan 1, 1942

By W. W. Adams

With greater production of coal per man-hour of work than ever before achieved, the coal-mining industry of the United States established a better safety record in 1941 than in any year since 1930, the earliest for which complete reports of nonfatal as well as fatal injuries were collected by the Bureau of Mines, United States Department of the Interior. In only one year (1933) of the 12-year period 1930-41 was the fatal-accident rate better than in 1941, whereas the rate for nonfatal accidents was better in 1941 than in any previous year. Accident and employment reports received from mine operators, together with fatal-accident reports received monthly from State mining departments and inspectors, showed that 546,692 men were employed in and about the coal mines of the United States during the calendar year 1941. This number does not include office employees or coke-oven workers. The increase of 1.3,426 over the number of employees in 1940 was accompanied by a gain in man-hours of work performed at the mines and an increase in average number of hours worked per man during the year.

Jan 1, 1944

By Charles T. Holland

ANALYSIS of 117 occurrences of bumps in coal mines shows that 67.6 percent are associated with pillar-line points.4 Slabbing and splitting pillars, development, and other unfavorable milling practices in abutment areas may be a contributory or the primary cause of bumps. The cure for pillar-line bumps is to recognize areas that can be expected to become highly stressed and to project the mining plan and operations to eliminate such areas insofar as possible. If such areas cannot be eliminated, then the mining plan and operations should be projected to avoid the necessity of disturbing these areas before the stresses have been dissipated.

Jan 1, 1954

By George Watkin Evans

The United States Geological Survey has estimated 1 that the State of Washington contains 11,412,000,000 tons of bituminous coal and 52,442,000,000 tons of subbituminous coal, in beds more than 14 inches thick. As the present rate of production is about 4,000,000 tons a year, Washington apparently contains coal enough to supply Pacific coast markets for many years. The character of the coal beds of Washington renders the production of clean coal very difficult, and a considerable proportion of the output is washed before it is marketed. In 1915 Washington ranked fifth among the States in the amount of coal washed, though only twentieth in total output. In that year 37.9 per cent of the coal produced in the State was treated in surface cleaning plants.

Jan 1, 1924

By George Rice

SOME form of longwall mining is generally used in Continental Europe; also in Great Britain where the coal is weak and friable, or the coal bed provides material for pack walls and filling, or where the bottom is soft and squeezes up easily, or the roof is pliable, or the bed is thin and brushing provides building material, or the thick multiple seams are mined in layers, such as the 24-ft. seam at Weymss, Scotland or the 10-yd. pitching bed near Coventry, England. Pillar methods have been retained in British fields where the coal beds are from 5 to 9 ft. (1.5 to 2.7 m.) thick, and free from thick partings or binders or without draw slate, which would provide waste rock for pack walls, or where the roof is hard and requires shooting to bring down and also the bottom or floor is comparatively hard. The room-and-pillar system, by which probably 95 per cent., of the coal of the United States is produced, is now found in only a few mines in Wales, where it is known as the pillar. and .(single) stall method. The American room-and-pillar system is not equivalent to the bord-and-pillar or stoop-and-room system. The essential difference between the bord-and-pillar and the average American room-and-pillar system is probably due to natural conditions. The majority of the coal mines in the United States have a depth of less than 700 ft. (213.m.). The bulk of the coal mined in Europe comes from a depth of more than 1200, ft., while the deepest mines in Great Britain, Belgium, and France reach 3500 to 4000 ft. In deep workings wide spans are impracticable, even with the use of abundant timber; accordingly, as the mines in the United States become deeper the rooms will become narrower and the pillars thicker, and the bulk of the coal will be extracted on the retreat. It is generally conceded, without reference to the cost of production, that the larger the pillars left on the first mining, the more thoroughly can the, coal be extracted. In Europe complete extraction is generally compelled either by the lessors or by the governments; whereas in this

Jan 2, 1921

By Kenneth J. Miller

A novel two-stage froth flotation process to remove pyritic sulfur from fine- size coal is described. The process consists of a first-stage, standard coal flotation step in which high-ash refuse and some of the pyrite are removed as tailings. The first-stage clean coal froth concentrate is then repulped in fresh water, and a coal depressant, a pyrite collector, and a frother are added to float the remaining pyritic material. Laboratory and pilot plant flotation results with coals from the Lower Freeport and Pittsburgh beds are given. The pilot plant test results show that up to 80 percent pyritic sulfur reduction was achieved with the Lower Freeport bed coal and up to 50 percent with the Pittsburgh bed coal. Laboratory and pilot plant results were in excellent agreement, indicating that the process is a viable means of removing much of the sulfur from some coals.

Jan 1, 1974

By H. F. Yancey

The investigations described in this bulletin are confined to a study of the washing characteristics of bituminous coals. The major part of the work was conducted by the Bureau of Mines in cooperation with the Engineering Experiment Station of the University of Illinois and the State of Illinois Geological Survey Division between 1918 and 1924, in accordance with the provisions of an agreement between these agencies. The washing characteristics of coals from many of the important coal-producing fields of the Eastern and Central States were examined. The coals of the Pacific Northwest States and Alaska have been studied separately by McMillan and Bird of the Northwest Experiment Station of the Bureau of Mines at Seattle in cooperation with the College of Mines of the University of Washington.2 OBJECT OF INVESTIGATION The object of the investigation of coal preparation by the Bureau of Mines has been to promote the production of better prepared coal and to facilitate the correct selection and design of coal-preparation plants by obtaining as complete information as possible regarding the washability of the various types of American coals and the treatment best suited to each. In addition, some attention has been given to the development of new methods of washing coal. The work naturally divides itself into three rather distinct steps: (1) Development of a systematic method of examining and testing a coal; (2) classification of the American coals on a basis of the occurrence of the impurities associated with the coal in the beds; (3) examination of one or more representative coals of each type.

Jan 1, 1929

By Robert V. Price

It is a pleasure to be here today to discuss coal's prospects with the Society of Mining Engineers of AIMS--- a group destined to play a crucial role in shaping our national energy future. Much has been said lately about attaining domestic energy self-sufficiency, but to date, little has been done. Oil tankers from Venezuela and Kuwait continue to glide across the seas to meet our incremental energy needs. Meanwhile, our principal domestic energy resources -- oil and natural gas reserves in the Outer Continental Shelf and the oil shale deposits and the coal lands of the West -remain untapped. Help, however, appears to be on the way. In a forceful address last fall, President Ford called for the elimination of oil as a fuel for base-loaded power plants and its replacement with coal by 1980. He also urged the accelerated leasing of federal lands on the Outer Continental Shelf, the resumption of coal leasing on federal lands, and the development of a new energy conservation policy. There are, of course, many details left to be worked out. Language must be developed to put statutory flesh on the conceptual bones spelled out by the President. Congress must act. Regulations must be approved and tested, if need be, in court.

Jan 1, 1975

By Seher Ata

This paper is concerned with the coalescence behaviour of two bubbles in dilute solutions of cetyltrimethylammonium bromide, methyl isobutyl carbonil and triton x-100. Two bubbles were produced at the tips of adjacent capillaries and the time elapsed between the first contact of the bubbles and film rupture was determined by means of a high speed camera. It was found that the amount of surfactant required to stabilise the bubbles increased in order of CTAB>TX-100>MIBC. The probability of coalescence decreased sharply with increasing surfactant concentration in CTAB and TX-100 solutions while with MIBC each bubble pairs resulted in coalescence, giving hundred per-cent coalescence probability.

Jan 1, 2014

By I D. Gregson, A S. Garcia, K M. MacAndrew

The design work undertaken by Rock Mechanics Technology (now part of Golder Associates (Golder)) has played a major part in successfully establishing mechanised room and pillar working in Indian coalmines, both for the development of new districts and for the re-establishment of old districts prior to pillar extraction on panel retreat.Golder has used appropriate design of pillars, extraction sequences and final snook sizes to minimise ground control risks during pillar extraction. Where the strata will not cave reliably, partial extraction systems leaving either a crush pillar or a substantial yield pillar have been adopted.Remote monitoring of selected pillars during the extraction process using stress cells, extensometry and convergence measurements provides confirmation of pillar behaviour and verification of designs.A new telltale device, giving a visible warning of impending caving, is now installed at all Indian pillar extraction sites and is proving very successful.CITATION:MacAndrew, K M, Garcia, A S and Gregson, I D, 2014. Coalmine pillar design and performance during mechanised pillar extraction in India, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 347–358 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By J M. Galvin

History attests to the catastrophic consequences that fire, explosion and contaminated, noxious andirrespirable atmospheres can have for workplace health and safety in underground coal mining. It also confirms that fires and explosions present the greatest risk of partial or total loss of underground mines and equipment and that this risk continues to materialise. The design, implementation, operation and maintenance of the mine ventilation system are core controls for managing the hazards associated with these risks, both for preventing them from materialising and for mitigating their consequences if they do materialise. These are most effective when embedded in a risk management approach.

Oct 12, 2022

By Albert L. Toenges

Early in 1944 the Chilean Government expressed a desire for assistance from the Bureau of Mines in a study of the coal deposits, coal-mining methods, and preparation and benefication of coals in Chile. A Memorandum of Understanding setting forth the purpose of the work was executed by the United States Government and the Government of Chile. Parts of this agreement are quoted: On February 4, 1944, the Ambassador of Chile in Washington expressed the interest of his Government in obtaining the loan of a mission of experts to assist in the conduct of a survey looking toward the utilization of the low-grade coals of Chile and the application of such technology as may be developed for the distillation of these coals and the use of oil shales. The matter has since been the subject of correspondence between the Secretary of State and the United States Department of the Interior, and the latter Department has agreed to cooperate with the Government of Chile, through the Bureau of Mines, subject to the following understanding:

Jan 1, 1948

By H. Walqui, S. K. Kawatra, C. H. N. Jeltema, T. C. Eisele

"The literature contains many cases where the shape of hydrocyclone efficiency curves vary from the ideal “S” shape. These often appear as changes in slope, or inflections. These inflections can be divided into two categories: “coarse” inflections, which are caused by differences in the density of the minerals being separated, and “fine” inflections, for which there are a number of competing hypotheses concerning their cause. The existing literature addresses either the fine inflection or the coarse inflection, but no studies have reported both types of inflection occurring at once in a single hydrocyclone test. This paper presents hydrocyclone results from both in-plant studies and laboratory experiments that show both coarse and fine inflections. The industrial significance of both types of inflections is discussed. Hydrocyclone efficiency curves show the probability of any given particle reporting to the hydrocyclone underflow as a function of its size. Selectivity functions, S(d), are used to represent the fraction of the feed material in size fraction “d” that reports to the hydrocyclone underflow. Plotting this selectivity function against particle size leads to the standard S-shaped efficiency curve shown in Fig. 1. In the “uncorrected” curve, the tail of the curve does not go through 0%, because a portion of the solids are bypassing classification. This happens as a result of their being carried along by the water, and is most important for the finest particles. The curve can be “corrected” based on the fraction of the feed water that reports to the underflow, represented by the bypass fraction, Rf. The corrected curve then normally passes through 0%, as shown in Fig. 1.The act of correcting the curve shifts the value of the d50 size, which is the size that has an equal probability of reporting to either the overflow or to the underflow. Correcting the curve to account for the bypass fraction makes it easier to compare cyclone performance under conditions that cause the quantity of water in the underflow to change, but that do not alter the actual corrected cut size (d50c).The corrected efficiency curve can be expressed closely by equations such as Plitt (1976):"

Jan 1, 2015