Search Documents

By Fritz Kleiner, Walter Meintrup

On Nov. 4, 1981 A/S Sydvaranger's 1-kt/h (1,100-stph) wet-process, iron ore ball mill completed its first four months of uninterrupted, full-load operation in Kirkenes, Norway. This 6.5-m-diam (21-ft-diam) mill is driven by a gearless ring or wraparound 8.1-MW (10,860-hp) motor at 13.1 rpm-a first of a kind in this segment of industry. This article examines reasons for selecting this type of drive over more conventional schemes, lists specific advantages of such large mills, and describes the installation in Norway. History For almost a decade, good operating experiences have been gained with 28 gearless ring motor drives in the cement industry, driving 2.5 to 4-m-diam (8.2 to 13-ft-diam) tube mills with drive powers ranging from about 3-4 MW (4,000 - 8,000 hp). Why then did the mineral ore processing industry hesitate until 1980 to adopt this successful concept for similar applications on ball, semiautogenous, and autogenous mills? There are a number of good reasons in the eyes of conservative mill builders and operators, the most commonly cited ones are: • No operating experience in this segment of specialized industry. • More severe environmental conditions in the wet ore grinding process. • An indifferent attitude of mill builders and electric motor manufacturers towards new drive technologies. • Limited confidence in solid-state power supply systems, such as frequency converters of the required size. There have been and still are numerous problems associated with low-speed geared mill drives of any kind, especially with individual motor/gear sizes approaching or exceeding about 4 MW (5,360 hp). Every mill builder knows about them, but operators learn to accept them as inevitable. The Decision to Change Three things combined to break this technological stalemate: the courage and progressive spirit of one major iron ore processor in Scandinavia, the cooperation of three experienced manufacturers, and an unusual application problem that could not be solved by any conventional approach. The last factor was surely the decisive one, but the first one does not come as a surprise either. The Swedes near Kiruna and the Norwegians around Kirkenes are experienced ore miners and processors, and much credit goes to them for technological breakthroughs in the industry. At A/S Sydvaranger in Kirkenes, above the Polar circle at about the latitude of Alaska's northern tip, the existing grinding facilities, with a total of 14 100 to 240-t/h (110 to 264-stph) ball mills, can not be expanded. Nevertheless, to increase mill throughput, only installing a larger mill in place of an existing smaller one was a practical alternative. For this replacement, the owners set requirements that seemed impossible to meet: • The old 100-t/h (110-stph) ball mill should be replaced with a new ball mill with 10 times the rated throughput, without significantly impairing the operation of the remaining mills, and without significantly changing the mill building. • The new mill should have a variable-speed drive to ultimately optimize the grinding process by means of a closed-loop process¬computer-controlled grinding cycle, and to minimize the specific energy consumption. • Availability, efficiency, and life expectancy of all new components must be higher than those being replaced. • Inrush-current and harmonic loads on the rather weak electric supply line must be minimized to ensure safe plant operation. All old ball mills at A/S Sydvaranger are the geared type, using single synchronous and wound-rotor, slow-speed motors with ring-and-pinion gears. Operators are familiar with the limitations and problems associated with such drives, and they are aware that the following items become major concerns when drive powers are drastically increased: • Gears are subject to wear and tear, require frequent maintenance, and eventual replacement of major parts. • Gears are sensitive to misalignment, overload, and thermal distortion, limiting their useful life. • On dual or quadruple drives, load-sharing and torque oscillations between motors can be a major reason for concern. • At these speeds, ring-and-pinion gears reach their torque transmission capabilities altogether at around 4 MW (5,360 hp) per motor/pinion. To obtain the desired variable-speed performance of the new drive, the only practical and economical conventional solution would have been a frequency-controlled, low- or medium-speed dual motor drive with about 8 MW (10,720 hp) of power. This, however, was not feasible because of limited floor space. Therefore, bids were solicited for the alternative drive method, the gearless ring motor. General Considerations Why are such large mills considered? After all, one could avoid all the problems by simply staying with smaller mill unit sizes. Under competitive pressures of free markets, however, grinding efficiencies and specific energy consumption become key factors in selecting new equipment. Specific energy consumption of ball mills decreases with increas-

Jan 9, 1982

By J. Silva, T. Worsey

The Worsey-Silva equation determines the optimal row timing for the smallest fragmentation and allows fragmentation models to be adjusted due to row timing. The equation utilizes the concept of dynamic confinement to determine when the best time to fire the next row or sequence series would be if the smallest fragmentation is desired. Full-scale testing was conducted at an aggregate quarry in Ontario to support the theory and equation. The full-scale testing comprised six (6) blasts, two (2) different contractors, and three (3) different sequences. The test parameters were kept consistent, besides changing the timing between sequential charges to explore the timing sequence’s influences on fragmentation. From this research, the theory of dynamic confinement relating to row timing was discovered, and the equation to determine the optimal timing for the smallest fragmentation was derived. An equation to adjust fragmentation based on row timing was derived from the full-scale testing and literature review. The Worsey-Silva equation can be used with other fragmentation models as it takes the fragmentation results from the other models and adjusts them based on the row timing used. The paper explains the theory behind the equation, the research supporting the findings, and the developed Worsey-Silva equation for row timing

Jan 1, 2024

By Darren S. Diehm

"Construction for the restoration and expansion of 102-year-old Wrigley Field in Chicago, Illinois began at the conclusion of the 2014 baseball season. This six year project involves structural upgrades to the Stadium, improvements to the facade, infrastructure, restrooms, concourses, suites, press box, and bullpens, as well as the addition of restaurants, patio areas, batting tunnels, video boards, an adjacent Office-retail Tower and a new Hotel. The Bleachers were demolished and replaced, and a new underground Clubhouse was constructed for the Chicago Cubs beneath a new open-air Plaza. The 1060 Project is privately funded, projected at $750 million (US). The work will be completed in phases during consecutive off-seasons, each with a maximum 23-week duration extending through the Chicago winter. Ownership mandated that on-going construction cause no disruption to the Major League Baseball season, have no impact on hosting concerts and other special events, and it should not adversely affect seating capacity, or diminish the fan experience.The 1060 ProjectAfter purchasing the Chicago Cubs baseball team in 2009 from the Tribune Company, the Ricketts family began planning the renovation and improvement of Wrigley Field and its near neighborhood surroundings in Chicago, Illinois. What came to be known as the 1060 Project was officially announced at the annual Cubs Convention in 2013. Construction began on the $750M privately funded project in October 2014 at the conclusion of the Major League Baseball season. In their vision, the Ricketts committed the 1060 Project to three primary goals. First and foremost as a MLB franchise, the work should provide a meaningful contribution toward winning the World Series and ending the championship drought which stretched to the last win in 1908. Second, the project should be focused on preserving and improving Wrigley Field. Finally, the project should be committed to outcomes that enable the team to be a good neighbor and provide economic and social benefit to the local community.Constructed as Weeghman Park in 1914 for an estimated total cost of $250,000, the stadium provided seating for 18,000 fans and a home for the Chi-Feds and Whales of the National Federal League. The Chicago Cubs were enticed to move from the West Side Grounds in 1915. In the next 100 years, the Wrigley Field would be sliced apart and expanded, double its seating capacity with the addition of double deck grandstands, be enclosed by bleachers (and an ivy covered wall), and, in 1988, experience its first nighttime baseball game with the addition of lighting.The 1060 Project has a total budget of $750M, with an expected construction value of $350M. It is projected to add over 2,100 jobs to the economy and be completed before the 2020 baseball season. The work will be completed in phases during consecutive off-seasons, each with a maximum 23-week duration extending through the Chicago winter. Ownership mandated that on-going construction cause no disruption to the Major League Baseball season, have no impact on hosting concerts and other special events, and it should not adversely affect seating capacity, or diminish the fan experience."

Jan 1, 1900

By William J. Miles

The markets and applications of Wyoming bentonite deposits are primarily determined by the functional properties of a bentonite ore which results from the unique mineralogy and chemistry of each deposit. Commercial bentonite products contain sodium montmorillonite as the major mineral component, with minor concentrations of accessory minerals such as quartz, opal (silica hydrate), mica, feldspar, gypsum and zeolites. The chemical composition of the sodium montmorillonite influences the functional properties of the bentonite in significant ways. The type and concentration of various accessory minerals also influence the acceptability of the bentonite in each market.

Jan 1, 1995

Wyoming State Geological Survey, Capitol bldg , Cheyenne, Wyoming. John G Marzel, State Geologist. Unfortunately, most of the publications of the Wyoming State Geological Survey are now out of print In particular should be mentioned Bulletins describing the various oil fields of Wyoming, and Bulletin 17, Bibliography and index (1918), all of which are out of print State geologic and topographic maps are also not available. A list of publications will be sent upon request Still available are: Bulletin 18, Mining laws, state and federal (1921), 19, Mineral hot springs of Wyoming (1926), 20, Atlantic City-South Pass gold mining district (1926), Circular 5, Operating regulations to govern the production of oil and gas on state and patented lands (1929). The last two Biennial Reports, issued 1928 and 1930, are still available. The bulletins and reports listed are distributed free.

Jan 1, 1933

By J. B. Hess, R. L. Dietrich

IN the mechanical twinning of magnesium on the {1012} planes the crystallographic deformation is such that, in the direction of the hexagonal axis [0001], twinning is possible only under tension stress, while in the directions perpendicular to the hexagonal axis, twinning is possible only under applied compression. Thus in extruded magnesium and magnesium alloys where the extruded textures are best described as either [1010] or [ 1120] fibers,1 the basal planes are all nearly parallel to the extrusion axis and such material is susceptible to {1012 } twinning by compression in the direction of the extrusion axis. In order to explain the results of cyclic stressing in alternate tension and compression upon the tangent elastic modulus in such material, Dorn and Thomsen2 have postulated that, following twinning under applied compression, a retwinning or untwinning occurs as a result of residual microtensile stresses immediately upon removal of the applied compressive force. Recently, Carapella and Shaw3,4 have used this supposition of untwinning in magnesium in discussing their results on indentation hardness and on cold drawing of MI sheet. In trying to confirm this hypothesis by suitable direct experiments, the authors have been unsuccessful in detecting any evidence whatsoever that untwinning follows the release of applied compression and are forced to conclude that this hypothesis is improbable or, at least, that the quantity of material involved is small. For the experiments, small cylindrical specimens 0.040-in. diam. X 0.120- to 0.140-in. long were etched from 0.0625-in. extruded rod. The ends of the specimens were accurately faced off parallel in a jeweler's lathe. The compression jig was simply an ordinary set of micrometer calipers with an anvil interposed between the spindle and the specimen. The anvil was free to move axially but restrained from rotating so that the rotation of the spindle would not introduce a twisting stress on the specimen. With this arrangement the compressive strains could be estimated to 0.0001 in. and X ray pinhole photographs could be taken with or without load as required. Fig 1 is the pattern of an uncompressed specimen of AZ31 alloy, showing the approximate [1010] extrusion fiber. The X ray beam is normal to the extrusion axis; in this position it is particularly sensitive in detecting twinning if one directs his attention to the diffraction ring from the basal plane. Since twinning on {1012} planes produced an 86° reorientation of the crystal lattice, the original basal reflections occur at the 3 and 9 o'clock positions while the (0002) reflections from any twinned material will occur at the 6 and 12 o'clock positions. Fig 2 shows the same specimen compressed 3.0 pct, photographed while still under load. This strain has been just enough to produce a detectible amount of twinning and the sensitivity is roughly indicated by the fact that no alterations were produced in the intensities or maxima of the other diffraction rings. A strain of

Jan 1, 1948

By M. Friedman

Applications of rock mechanics to the design of engineering structures in rock involve the assumption that the stresses are due entirely to the present applied loads. For instance, it is assumed that the vertical normal stress in undisturbed rock free of topographic effects is equal to the weight per unit area of the overburden. In fact, vertical dilatational strains associated with stresses of more than 100 times the present overburden pressure have been measured by strain-relief methods on outcrops. 1,2 The notion of residual strain (stress) or latent stress3 seems unassailable; and indeed this has long been recognized by metallurgists. It is difficult, however, to assess the residual component of the in-situ state of elastic strain with conventional strain relief methods employed in mines or down boreholes. That is, in principle, the in-situ state results from the superposition of present applied loads (natural or man- induced) and potentially recoverable elastic strains (stresses) that exist in a given volume of material even though there are no external forces across the boundaries of the body (Voight,4 and Fig, 1). Accordingly, only in unloaded blocks can the true residual strains be measured by strain relief methods. Using X-rays, the elastic strains locked within the quartz grains or crystals of a rock can be measured. These strains are known to persist even when the rock is reduced to small chips but to vanish when the rock is disaggregated and the grains are powdered. Although we have just begun to investigate the mechanisms by which the strains are stored (see Preliminary Results), we believe that "pressure solution'' at grain boundaries, secondary cementation under load, permanent ("plastic") deformation, and temperature changes are possible processes. In any event, in our study of naturally deformed rocks, it is significant that we are work-

Jan 1, 1972

By J. D. Nye, I. A. Farr, W. J. D. Stone

"A unique deposit of barite exists near Brookfield, Nova Scotia. The crystals are extremely fine and the whole deposit virtually free of heavy metals. The deposit size was not large enough for conventional uses, such as the production of barium carbonate and drilling mud. In an effort to obtain maximum utilization, a program was begun to determine if U.S.P.-grade pharmaceutical barium sulphate for X-ray diagnosis could be produced. Early work was sufficiently encouraging to institute a development program under the federal Program for Advancement of Industrial Technology. This has been very successfully completed. Canadian and U.S. process patents have been issued, clinical trials have been successful, a production plant has been designed and the plant’s production sold. The processing plant will include magnetic separation for the removal of iron minerals, fine grinding by paddle milling to minus one micron and acid leaching. The process is unique in that at no time is the barium taken into solution.Information is given on the deposit, process, markets, use, plant capital and operating costs, and projected profits. The initial production plant will have an annual capacity of 2,000 tons per year of end product. Capital cost is $850,000 and annual turnover more than $1.5 million. As this capacity only represents approximately 15% of the North American market, rapid plant expansion is foreseen."

Jan 1, 1980

By Chaoxun Zhao, TAIYOU LI, JIAQI JIN, Chen-Luh Lin, Jan D. Miller

A large portion of the energy consumed in copper concentrators is used to reduce the particle size of the feed by crushing and grinding. The cost of metal production could be reduced if low-grade particles of centimeter size were removed prior to further processing. Two copper sulfide ore samples (3 × 1 cm) from Arizona were analyzed by micro X-ray computed tomography (Micro-XCT) to determine the grade of copper sulfide in each particle. For copper ore sample A, a significant number of particles contained very low amounts of copper, while some particles had copper sulfide grains of millimeter size. Based on Micro-XCT, it was expected that 85 percent of copper for sample A could be recovered at 65 percent of mass rejection during preconcentration by sorting. However, in sample B (a different copper ore), distribution of copper sulfide was dispersed primarily in each ore particle, so for the particle size class of 3 × 1 cm, liberation of copper sulfide and gangue minerals was not significant. In view of the XCT results, dual-energy X-ray radiography was used as a basis for sorting. Pilot-scale X-ray sorting of sample A (10 × 1 cm) showed 31 percent rejection of a 0.08 percent Cu gangue product with a corresponding recovery of 90 percent copper.

By Martin Lebeuf

The phenomena occurring in the cathode and at the cathode surface of aluminum electrolysis cells are very important in regards to cathode voltage drop and cathode wear. In the current study, laboratory-scale aluminum electrolysis cell cathodes were analyzed by X-ray microtomography. This technique allows an excellent visualization of the distribution of different substances, if their respective X-ray attenuation coefficients are different enough. In the current case, the important difference in the mean atomic number between cryolitic bath and graphitic carbon results in good contrasts. The volumetric bath penetration profile, porosity and impurities distribution in the cathode were thus obtained. Furthermore, metallic impurities and bath heterogeneities were observed at the cathode surface. Observations were also made with Scanning Electron Microscopy - Energy Dispersive Spectroscopy (SEM-EDS).

Jan 1, 2011

By Sabri Ergun

This report gives the result of investigations of coals of different rank, coal com¬ponents, chemically and thermally treated and irradiated coals, and sedimented organic matter. In most studies the arbitrary parameters obtained from the usual quantitative profile analyses are not given largely because they lack physical meaning. Instead comp interpretations are offered. X-ray patterns of high-volatile bituminous and lower rank coals are not self¬-sufficient for structural interpretation by the methods of analysis developed to date. The patterns of hydrogenated and dehydrogenated coals indicate that the basic change in the structure of bituminous coals with increase in rank is the conversion of alicyclic structures into aromatic layers. In low-rank anthracites the aromatic layers are about 10 A in size. The increase in rank is the result of coalescence of layers. High-rank anthracites have layer sizes of 25 to 40 A and exhibit the development of three-dimensional (hkl) reflections of graphite, indicating ordering of adjacent layers. In meta-anthracites the layers are > 1000 A and the basic structure is that of defective crystalline graphite. The well-known petrographic components in low-rank coals have different structures; the differences dissappear in low-volatile bituminous and higher rank coals. The patterns of sedimented organic matter, except impsonites, differ from those of coal hydrogen contents are high, and their X-ray patterns are consistent with those of structures. In contrast to normal coals, the patterns of uranium-bearing coals show increased diffuseness with decrease in hydrogen content. The diffuseness is accompanied by increase in the uranium content of the coal. It is very likely that high uranium-bearing coals have predominantly tetrahedral structures.

Jan 1, 1968

By John Norton

IN spite of the very general employment of nitride hardening, there is still considerable doubt as to the real nature of the mechanism involved. Experience has shown that the addition of small amounts of hardening elements to iron or steel results in a wide variety of desirable properties in a nitrided case. Perhaps the foremost of these elements is aluminum and in this investigation an attempt has been made to study the behavior of aluminum during the hardening process. It is believed that the establishment of a complete atomic picture of the metal at various stages of the process will indicate the relationships between the several kinds of atoms and their individual influences on the physical properties in a clear and direct fashion. A consideration of the problem suggests a surprising similarity between the mechanisms of nitride hardening and of age-hardening. It is now generally understood that age-hardening may take place by one of two distinct processes, the first involving the precipitation of a finely dispersed phase and the other being concerned with the modifica-tion of an existing phase. Following much the same line of reasoning, two theories of nitride hardening have been suggested. The first expla-nation, which has been generally discussed, particularly by Fry,1 states in brief that the presence of aluminum causes the precipitation of alumi-num nitride during nitriding and that this finely dispersed phase is the primary cause of hardening. The second explanation, which has not been published but which has been freely discussed by those interested in the problem, postulates the substitution of aluminum atoms for certain of the iron atoms in the several iron-nitrogen phases in the same manner that the substitutional iron-aluminum solid solution is formed. The marked increase in hardness, as compared with the aluminum-free

Jan 1, 1934

By J. D. Miller, C. L. Lin

From mine to mill, the 3D characterization of particles ranging in size from meters to micrometers is now possible. A brief review of X-ray tomography for mineral processing is given with recent advances considered, such as high-speed scanning and image analysis procedures to describe important particle properties, including size, shape and composition. Considering these new 3D characterization tools, applications in mineral processing are discussed for high-resolution X-ray microtomography (HRXMT) laboratory analysis of particles ranging from 20 mm to 5 μm, with a voxel resolution of about 1 μm, including (1) multiphase particle characterization by HRXMT and comparison with scanning electron microscopy (SEM), (2) particle damage state as a result of blasting/comminution, (3) liberation characterization to describe expected separation efficiency, (4) exposed grain surface area analysis to explain the flotation of locked particles, and (5) floc size, shape and water content for polymer-induced flocculation. Finally, applications in mineral processing for plant-site analysis using high-speed X-ray computed tomography (HSXCT) are examined, including, for example, coal washability analysis, the analysis of crusher plant products, and the analysis of pebble phosphate products from central Florida. Scanning rates on the order of 1 kg/min for particle sizes ranging from 150 mm to 1 mm are possible, with a voxel resolution of about 100 μm. For coarse particles smaller than 5 to 10 mm, high scanning rates of more than 300 t/h may be possible at a voxel resolution of about 1 mm.

By Christopher Robben, Alexander Mosser

"X-ray transmission (XRT) sorting has been introduced into the minerals industry in 2006 and has found various applications in diamonds, industrial minerals and metal ore processing since. The technology offers planar projections of the atomic density of single particles similar to the principle known from airport scanners, but being capable of treating up to 150tph per metre working width. In 2010, a pilot operation using a belt-type sensor-based sorter went into production at the Mittersill mine to treat the fraction 16-28mm. After an optimisation phase, the results were superseding expectations and therefore in 2012 a bigger production plant was set up. Two XRT-based sorters are parallel in operation since. One is treating the fine fraction 16-30mm while the other one is treating the coarser fraction 30-60mm after the secondary crushing stage. The XRT sorters are operated with the objective to reject barren waste before it enters the mill and flotation plant. 105,000tpa of waste material are rejected per year and can be sold as aggregate for road construction. This means that about 22% of the run-of-mine ore are rejected at an early stage with a waste reject grade lower than 0.03wt%WO3. The installation has not only led to lower specific operating costs but also led to reduced tailings disposal in an environmentally sensitive area. This allows the mine to reduce its headgrade which allows for a longer mine life. Alternatively it is possible to produce more tungsten concentrate, which is delivered to the smelter. This article will introduce the technological principle of XRT-based sorting and will discuss the flow-sheet of the Mittersill mine. Experiences that have led to the current plant design are described as well as the impact it has on the operation."

Jan 1, 2014

By Finn Ouchterlony, José A. Sanchidrián

"A model for fragmentation in bench blasting that originates from dimensional analysis of fragmentation in asteroid collisions is presented. Percentiles of the size distribution are obtained in the basic model as the product of a rock strength-to-explosive energy ratio, a bench shape factor, a scale factor or characteristic size and a percentage passing-related factor. The parameters of the model are fitted to 169 bench blasts in different sites and rock types, bench geometries and delay times, for which thefragmentation of the muckpile was obtained by sieving. The basic model is found to significantlyimprove with an additional factor describing the rock mass structure in terms of the spacing and orientation of discontinuities, and another one describing the delay between successive contiguous shots; the latter is conveniently formulated as a function of the P-wave velocity and the holes spacing. The rock strength property chosen is the strain energy at rupture that, together with the explosive energy density in the rock (or energy powder factor), forms a combined rock strength/explosive energy nondimensionalfactor. The model, called xP-frag, is applicable from 5 to 100 percentile fragment sizes, with all parameters determined from the fits significant to a 0.05 level. The expected error of the prediction is below 25 % at any percentile. These errors are half to one third of the errors expected with the best prediction models available to date."

Jan 1, 2017

By T. J. White

Xtaltite is the trade name for a generic technology which exploits the well known insolubility of some minerals, which naturally incorporate toxic waste elements, to consolidate and immobilise a range of inorganic waste products. It is a specific case of synthetic mineral immobilisation technology (SMITE) which is already used to immobilise high level nuclear wastes (HLW. Although HLW is highly toxic, it exists in relatively small volumes, occurs in central facilities and may be stabilised at low waste loading (< 10 wt%). In contrast, heavy metal wastes are of considerable volume, therefore Xtalitite waste forms must routinely accommodate high waste loadings (usually in excess of 30 wt% for a particular toxic oxide or combination of oxides) and be suitable for fabrication in remote locations using relatively simple technology. This paper details the methodology underlying Xtaltite, with particular emphasis given to the interplay between solid state chemistry, durability and economic considerations. Specific reference is made to the treatment of arsenious and mercurial wastes.

Jan 1, 1994

By John G. Reid

When the paper "Operations at the Greenvale Nickel Project Mine and Refinery" was delivered at the 1st International Laterite Symposium in February 1979, the Yabulu Caron plant had been operating for four years and production had just stabilized. The design had been based closely on the Caron plant at Nicaro, Cuba, built in 1944, also by Freeport. Yabulu had 10 Herreshoff ore roasters and production in 1978 was 18,682 tonne nickel as impure oxide sinter and 763 tonne cobalt in a mixed sulphide with a cobalt to nickel ratio of 1 :2.5. In the 25 years since the 1st Symposium, two more roasters have been added, but dry ore processing rate has remained relatively unchanged at 2.4M Uyr to allow a lower feed rate per roaster with associated higher recovery. The ore source has changed from the domestic Greenvale mine to imports from New Caledonia, Indonesia and the Philippines. Nickel production between 1978 and 2003 has risen by 67%, cobalt has risen by 146% and the products have changed to high purity nickel compacts and "ChemGrade" cobalt salt. The plant changes that have contributed to the increased recovery, production and product value are discussed. Keywords: Caron, Yabulu, nickel, cobalt, ammonia

Jan 1, 2004

By Ben Burger

This paper describes the design, the first three years of operation and optimization of a large, single stage SAG mill at Minera Yanacocha?s Gold Mill facility located in northern Peru. The Gold Mill was commissioned in March 2008 with a 32? x 32? EGL, 16.5MW single stage SAG mill, to process 5 million tonnes per annum high grade oxide Au/Ag ore. Operational control, feed size distribution, grinding media, mill liner, grate and pulp lifter optimisation have allowed the mill to operate 15-30% above design throughput rates, but with a product P80 coarser than design. As part of the optimization, full grinding circuit surveys were conducted. Historical operating data and survey data were analyzed and used to evaluate possible circuit changes and determine alternative operating strategies. A number of changes were implemented which allowed the SAG mill to operate similarly to a large ball mill and achieve finer mill product that was closer to design. This paper summarizes life to date data analysis and improvements made by Minera Yanacocha as well as the grinding circuit optimisation study conducted by Metso Process Technology and Innovation.

Jan 1, 2012

By E. W. Coderre, R. C. Baxter

"This paper describes the townsite of Wabush and the two railways operated by Wabush Mines for the loading and unloading of iron ore concentrate. The town of Wabush is located approximately 200 air miles north of Sept-Iles, Quebec and is in the Province of Newfoundland and Labrador. Construction of the town-site began in 1961 to provide housing accommodation for the construction force and permanent employees in the mining and milling operations located 4 miles away. Wabush Mines operates two short railway lines in loading and unloading concentrate between the concentrator, located at Wabush, and the pellet plant at Pointe Noire, Quebec. Both of these railways connect with the main line of the Quebec North Shore and Labrador Railway and provide a shuttle service between the two phases of the operation."

Jan 1, 1969

By E. Lee

With the growing environmental concern, as well as the increasing concern for sustainability of natural resources, the need of improving the performance and efficiency of today?s crushers is be-coming increasingly important. However, the development of existing crushers requires an extended basic knowledge about the crushing process itself. The aim of the present study is therefore to find the theoretically optimal way of crushing compressively under given circumstances. In the present paper, optimizations have been performed with the purposes of maximizing product yield and minimizing energy consumption. Performed on an ideal crushing stage free from physical limitations, the optimization results have been obtained in terms of number of compressions and their corresponding compression ratios. Complementing earlier results on interparticle breakage (Hulthén et al., 2006), presented here are thus the results from corresponding optimizations with single particle breakage and interparticle breakage. It is concluded that modern crushers are not working optimally in any of the studied aspects for gneiss. In fact, optimizations indicate that a lowering of the compression ratio, as well as a shortening of the crushing sequence, are theoretically favourable. The outcome of this study is therefore highly promising as to giving new ideas and suggestions of improvements in existing crushers, and can even result in redesign of compression crushers.

Jan 1, 2014