Search Documents

By J. L. Gissy, G. H. Schippereit, J. B. Schroder

THE existence of mechanical anisotropy in hexagonal metals is well known.' One possible method of measuring the degree of anisotropy in a metal is to make hardness measurements on the different planes of a single crystal. So far as is known, no single-crystal hardness data have been reported in the literature for alpha titanium. To obtain an estimate of the variation in hardness with crystallographic direction in titanium, Knoop hardness measurements were made on single crystals of electrorefined alpha titanium obtained from the Bureau of Mines, Boulder City, Nev. The hardness of arc-melted ingots prepared from this material was 64 Bhn (1000-kg load, 30 sec). Crystals of sufficient size were mounted in epoxy resin with the basal plane exposed. They were then polished and etched to remove excess plastic resin and work-hardened surface material. The crystals were then examined by x-ray diffraction, using the back-reflection Laue technique to insure that the crystals were properly oriented and strain free. After Knoop hardness readings (100 or 200-g load) were taken on the exposed surface, the crystals were remounted to expose a prismatic face and the foregoing procedure was repeated. Hardness values for various orientations are listed in Table I. The data show a difference between the hardness of the basal planes and that of the prismatic planes, as anticipated. More striking is the hardness difference observed between different orientations of the indentor on the prismatic planes as shown in Table I and Fig. 1. All of the indentations shown in Fig. 1 were made with a 100-g load. The long axis of indentation A is parallel to the unique (c) axis of the crystal. The deformation marks visible around indentations A and C of Fig. 1 are probably slip traces of the (10.0) system reported by Rosi, et al. The greater hardness observed when the long axis of the indentor was perpendicular to the unique axis of the crystal (indention B) is probably caused by the opera-

Jan 1, 1959

By E. H. Greener, M. E. Fine

The internal friction (1/Q) of cobalt Fig. 1 (measured by an electrostatic dynamic method1) near 250°C begins to increase rapidly on heating and continues to increase until 560°C, the highest tem- perature measured. In the plot of log of 1/Q against 1/T, above 250°C the data nearly fit two straight lines intersecting at 400°C, approximately the temperature of the hexagonal-cubic transformation. The higher temperature branch corresponds to an effective activation energy of 6500 cal per mole, the lower temperature branch 11,000 cal per mole. Young's modulus Fig. 2 increases approximately

Jan 1, 1959

By G. W. Preckshot, J. W. Gorman

MOLTEN metals offer an excellent medium for the study of molecular diffusion and interphase transfer. In the absence of intermetallic compound formation, solutions of molten metals are solutions of elements. Therefore, complicating factors such as molecular structure, dissociation, association, polarization, and so on, are generally absent. Further, metals remain in the liquid state over a wide range of temperature. Thus, the effect of temperature on transport processes can be studied in more detail. Although some data are available for the diffusion of metals in the molten state at high temperatures,"""".'!' the most useful and accurate data are those for the diffusion of various elements in mercury at room temperature. The effective radius of diffusion for the various elements in mercury may be calculated from the Stokes-Einstein relation.'-These calculated radii are compared with the atomic and ionic radii calculated from X-ray data on crystals." The effective radii of diffusion of the alkali and alkali-earth metals correspond to those of the neutral atom; those of cadmium, silver, lead, zinc, thallium, bismuth, and tin correspond to ionic radii; and those of copper and gold indicate larger radii due to association with mercury or more likely, faulty diffusion data. Independent evidence"' supports the notion that alkali metals are uncharged in amalgams. The concept of metals moving free of their conductance electrons in the liquid state has been discussed by Eyring, et al,'" in connection with studies on the viscosity of pure molten metals. Considering the approximate nature of the tabulated atomic and ionic radii and the variance in the diffusion measurements, the application of the Stokes-Einstein equation to the diffusion of metals in mercury gives gratifying results. It is noted that a number of these metals have article radii eaual to or less than those of the solvent mercury.".'*,"' Soba1,'" sing the inaccurate Roberts-Austin20 data, indicated that the effective radius of diffusion might well be a function of temperature. Additionally in studies of mass transfer between phases, many conflicting opinions have been expressed concerning the assumption of equilibrium at the interface." ,","," The results of the present work on the diffusion of solid copper in molten lead throws light on the tempera- ture variation of the diffusion radius as well as the extent of the interfacial resistance. The theoretical background and experimental procedure are presented here in detail. Results on other systems will be presented in subsequent papers. Nomenclature The following nomenclature is used in the paper: A—cross-sectional area of diffusion column, sq cm C, C,—concentration of solution and saturated solution respectively, g per cc D,D'—-diffusivity, sq cm per sec e—Naperian base h—ratio, k/D k—mass-transfer coefficient, cm per sec L—diffusion column length, cm n—series index q—flux, g per sq cm-sec r—radius, cm or A R—-gas constant t—time, sec T—temperature, K V—volume, cc w—weight of copper-lead alloy on copper cylinder WT—-total copper transferred to lead diffusion, column, g Z—distance from top of diffusion column, cm 2'—distance from copper-lead interface, cm (2' = L-2) u,,—roots of diffusion equation Mathematical Apparatus The model shown in Fig. 1 applies to the diffusion of solid copper into molten lead. Here Fick's first law may be written where all terms are defined in the nomenclature. It is assumed that the volume of the lead column is constant. This is justified since experimental densities compared favorably with calculated densities based on perfect interstitial mixing. Thus there is no counter diffusion of lead. It is clear that 2 in Equation [I] should be measured relative to the interface which moves relative to the diffusion cell but not to the liquid phase. Hence, the frame of reference is the plane of the copper-lead interface. The diffusivity calculated at constant volume, D", is that defined by Hartly and Crank" and is designated herein as D. No Interfacial Resistance—The two situations of the presence and absence of interfacial resistance will be treated. The simplest is the latter which re-

Jan 1, 1959

By W. Rostoker, A. S. Yamamoto, K. Anderko

ALTHOUGH the corrosion resistance of magnesium and its alloys is closely related to iron content, there has been no direct measurement of the solid solubility of iron in magnesium. Bulian and Fahrenhors;1 and Mitchel]2 agree that pure iron or a limited terminal solid solution crystallizes from the Mg-rich liquid. For this reason a magnetic-moment method was selected to estimate that portion of the total iron content which is not in solid solution. Since iron in solid solution in magnesium cannot contribute to ferromagnetism, the difference between chemical and magnetic-iron analyses should yield the solid solubility. By experimentation it was found that the melting of pure sublimed magnesium (99.995 wt pet purity) in Armco-iron crucibles at about 800°C is a convenient way to introduce small amounts of iron. Melts retained 5, 10 and 20 min at 800°C analyzed 0.003,, 0.005,, and 0.018 & 0.001 weight pet Fe, respectively, after being stirred, heated to 850°C, and cast into graphite molds. The as-cast alloys were pickled in acid (dilute HC1 + HNO3), annealed at 600°C for 3 days, scalped on a lathe to remove the pitted surface, pickled again, extruded at about 100°C to 3-mm wire, reannealed 41/2 days at 500°C, and water-quenched. The specimens were again scalped, pickled, and used both for chemical and for magnetic analysis. Most of the precautions described were intended to prevent iron pickup by contact with tools or superficial iron enrichment by volatilization of magnesium during heat-treatment. It is believed that the specimens ultimately used for test were homogeneous and characteristic of phase equilibria at 500°C. Magnetic Analyses A susceptibility apparatus of the Curie type was used for magnetic analyses. Field strengths of up to 10,400 oersteds could be generated. By this method, an analytical balance measures the force of attraction which a calibrated magnetic field exerts on a suspended specimen. The force equation is as follows f/m = M dh/dy where f/m = force per unit mass of sample M = magnetic moment per unit mass dH/dy = magnetic field gradient The dH/dy characteristic of the instrument is determined by the use of a standard palladium sample, and the calibration is made independently for all values of H. Since a large finite field is required to saturate an assembly of ferromagnets, it is necessary to measure the apparent magnetic moment for increasing steps of H until a saturation value is obtained. The percentage of iron in the sample as free ferromagnetic iron may then be computed simply C= 100 (M1/M1) where C = percent content of undissolved iron in sample M1 = saturation magnetic moment of sample per unit mass M1 = saturation magnetic moment of iron per unit mass taken as 217 emu-cm per gm There is no serious difficulty in applying this method except for the unusual magnetic behavior of very fine particles of ferromagnetic substances. It has been found and is the basis for a widely accepted theory that with sufficient subdivision, the magnetic fields required to saturate and the coercive force after saturation rise to exceedingly high values. Recent work on precipitates of Fe and Co from copper solid solutions8 showed that about 5000 oersteds were necessary to approach saturation. The magnetic moments as a function of field strength measured in the present investigation are listed in Table I. Only the 0.018 wt pet Fe alloy yielded a magnetization curve with a fairly well-defined saturation plateau at 3.76x10 -2 emu-cm/ gm. This corresponds to 0.017 & 0.001 wt pet Fe in the alloy. This indicates that the solid solubility must be of the order of 0.001 wt pet Fe. The magnetic-moment data of the other two alloys are badly scattered, indicating that the amount of ferromagnetic iron in these samples is so low that the magnetic forces acting on them cannot be measured accurately by the analytical balance used. Nevertheless, the fact that even the 0.003, wt pet Fe alloy shows ferromagnetism indicates that the solid solubility must be below that value. Acknowledgment This work was sponsored by the Pitman-Dunn Laboratory of Frankford Arsenal, Philadelphia, Pa. The support and permission to publish are gratefully acknowledged. References W. Bulian and E. Fahrenhorst: Zeic. Metallkunde, 1942, vol. 34, pp. 116-170. 2 D. W. Mitchell: AIME Transactions, 1948, vol. 175, pp. 570-578. 3 G. Bate, D. Schofield, and W. Sucksmith: Philosophical Magnsine, 1955, vol. 46, pp. 621-631.

Jan 1, 1959

By R. L. Fleischer, B. Chalmers

In order to observe size effects associated with a grain boundary, aluminum single crystals and bicrystals of various cross-sectional dimensions were deformed in tension. Typical stress-strain curves are presented in conjunction with measurements of the effects of changes in crystal dimensions. Some effects of the growth rate used in preparation of crystals are also described. It is indicated that the macroscopic constraints at a grain boundary are responsible for the most prominent grain-boundary effect, the production of multiple slip. Two measurements of the width of the region of double slip are in agreement. It is concluded that the yield stress of aluminum is affected markedly by the inherent oxide coating. THE general problem to be examined is that of dimensional effects in the plastic deformation of metal crystals. These effects will be termed "size effects" and are here defined as follows: A size effect occurs in a series of crystals if their plastic-deformation properties are a function of crystal dimensions. Clearly then size effects depend on the nature of the boundary conditions imposed on the crystal. Crystal boundaries can be of three types: interphase, inter-crystalline, and free surface. Such deformation effects as are caused by distribution of phases, grain size, lineage structure, and single crystal external geometry are specific types of size effects. This discussion will be confined primarily to grain-boundary and single-crystal size effects, though in practice most "single crystals" not only have a number of small angle boundaries but also have one or more surface phases, so that the boundary conditions appropriate to a free surface do not necessarily apply. Hence, to this extent interphase size effects will be considered. The question of size effects associated with grain boundaries (called here intercrystalline size effects)

Jan 1, 1959

By J. O. Betterton, W. M. Spicer

The solubilities of antimony in the a and ß-forms of zirconium were determined between 750" and 1300°C. The a-phase forms by a peritectoid reaction, and the a/(a + ß) and ß/(a + ß) phase boundaries rise in temperature with in- ' creasing antimony. Impurities in the 99.95 pct zirconium were sufficient to influence the phase boundaries and the variation reported is approximate. The restricted solid solubility of the terminal zirconium phases, which is especially characteristic of this system, is thought to result from the low free energy of the Zr2Sb phase. ZIRCONIUM-antimony alloys are important in zirconium alloying studies since antimony is one of the highest valent elements which can be used to make zirconium alloys. The dilute alloys are of further interest as they have somewhat better corrosion resistance' than pure zirconium. The first investigation of the phase diagram was made by Russi and wilhelm2 who found a eutectic reaction, liquid (- 17.5 at. pct Sb) = ß zirconium (- 11 at. pct Sb) + Zr2Sb, at 1430°C'. The Zr2Sb phase was of complicated hexagonal structure, and by thermal analyses of the relatively impure alloys then available, Russi and Wilhelm found evidence for the peritectoid formation of the a-phase. EXPERIMENTAL In the present work, the phase diagram was re-investigated in the region 0 to 5 at. pct Sb and 750" to 1300°C using iodide-zirconium alloys. Details of the procedure have been described earlier. Essentially the alloys were prepared by arc casting and were then examined by the annealing and quenching method. The times of annealing varied from 1 hr at 1300°C to 30 days at 760°C. As in other zirconium phase-diagram studies1"5 the impurities in the zirconium were still sufficient to affect the results, and the experiments will therefore be described in 3 parts. The results from the first 2 parts of the work are shown in Fig. 1. Here the ß/(ß + Zr2Sb) and a/(a + ZrzSb) phase boundaries were determined with alloys made from 99.9 pct zirconium,* and cast under such conditions that the Vickers hardness of a alloys extrapolated to 95 to 110 VPN at 0 at. pct Sb. Such alloys were not suitable for investigations of the (a + ß) region, and the results shown in Fig. 1 near the (a+ ß) and (a +ß + Zr2Sb) regions were determined with purer alloys. These alloys had an extrapolated hardness range of 75 to 85 VPN and were made from 99.95 pct zirconium. A deviation from binary equilibrium occurs in Fig. 1 as indicated by the (a + ß) region of pure

Jan 1, 1959

By M. Metzger, T. A. Read

The strengthening effects of hydroxide and synthetic plastic films in the creep of cadmium crystals were studied. The results were broadly consistent with the naive mechanical model. The dislocation-film reactions and the significance of the macroscopic stresses associated with certain films are discussed in the paper. ALTHOUGH a number of studies have been made of the strengthening of metal single crystals produced by surface films usually less than Ir in thickness, the mechanisms underlying this phenomenon are still not well established. Roscoe' first noted the critical shear stress and the stress-strain curve of cadmium-crystal wires to be raised markedly by the presence of oxide films. Subsequent investigators2-' have confirmed the effect for several metals and films including a number of plated poly-crystalline metal films. Harper and Cottrel1" with a thin film on zinc presumed to have formed as a result of etching and washing treatments) did not detect a strengthening at a rate of extension of 10 ' sec-' although at lo-' sec-' the film raised the flow stress by 7 pct at 0.0005 extension and by 22 pct at 0.01. The marked strengthening at moderate strains thus appeared to be the result of a dynamical effect dependent on the rate and amount of plastic flow. Other observations'. " are consistent with this view. The large effects of films on the tensile creep rate of single crystals were demonstrated when the observation of Andrade and Randall," that the creep rate of cadmium crystals increased on immersion in aaueous solutions of certain cadmium salts. was shown' * to hold only when a film was present initially and was explained by the attack of the solution on the film and the removal of its strengthening effect. Changes in the creep rate interpretable in terms of the removal or formation of various films have been observed by other investigators.3,8,10,31 Certain other experiments have been reported in which surface films or liquid environments have affected the plastic behavior of metals, but these are not within the scope of the present work which deals with the effect of solid films on single-crystal slip. Possible Mechanisms—The film does not significantly reduce the load on the crystal in the elastic range (the elastic moduli of film and crystal are not too greatly different and the area of the film is so small that its share of the load is negligible) so that the initial operation of internal Frank-Read sources is not affected. However, as Fisher" has pointed out, a source terminating on the crystal surface requires only half the critical stress for activation as an internal source of the same length and a relatively strong film (even a very thin one) would pin the free ends of the surface sources so that, if surface sources are responsible for plastic flow in a clean crystal. such a film would increase by roughly a factor of 2 the stress necessary for generation of dislocation loops at a given rate. The other general possibility is that the film resists the passage to the crystal surface of internally generated dislocations. If the film is adherent and if the specimen is to exhibit slip of the same general character as a film-free specimen, the film must deform or fail in shear at the active slip planes. The naive mechanical model, where shear-stress relaxation across the active slip plane in the metal transfers load to the film until it deforms and slip can

Jan 1, 1959

By J. Gurland

A method of measuring the degree of contact between grains of 1 phase in multiphase alloys is derived. It is shown that the number and the areas of contacts between grains can be determined by metallographic analysis. Relations between the area of contact, the dihedral angle, and the mean free path of spherical grains are developed. It is often desirable to interpret the mechanical behavior of alloys in terms of structural features observed under the microscope. A quantitative description of microstructures of multi-phase alloys requires consideration of geometrical and topological factors such as the amount, size, and shape of grains and the continuity of the constituent phases. The number and dimensions of grains may be metallographically determined by applying the methods described by Smith and Guttman1 and by Fullman2 in their papers on the measurement of particle size and internal boundaries in opaque bodies. The present work intends to show that the same methods can be used to evaluate some of the parameters of phase continuity; namely, contiguity, number of contacts, and areas of contact of grains of 1 phase. Application of these concepts may be found in such problems as the calculation of electrical conductivity of 2-phase alloys, or the evaluation of the length of fracture path through grains of a brittle phase more or less dispersed in a matrix. I. DEFINITION The following definitions and derivations are based on 2-phase alloys, of which the units of the microstructure are grains. Contiguity is defined as the average fraction of surface area shared by 1 grain of a phase with all neighboring grains of the same phase. In a 2-phase alloy of constituents A and B, the contiguity of phase B is given by: where Cb is the contiguity of phase B aBß is the average area of contact between a grain of phase B and adjacent grains of phase B, aAB is the average area of contact between a grain of phase B and adjacent grains of phase A. The contiguity is a measure of the average degree of contact between grains of phase B in the 2-phase mixture. The ratio varies from 0 to 1 as the distribution of phase B changes from a completely dispersed to a fully agglomerated structure. Smith and Guttman1 have shown that the relative areas of 2 kinds of interfaces in a volume are directly proportional to the number of interfaces of each type intersected by a random line. The lines can be drawn on metallographically prepared surfaces as long as these are random sections through the sample. The contiguity ratio of phase B then becomes: Cb = 2NBB/NAB + 2N BB [2] where: NBB is the number of interfaces between grains of phase B intersected per unit length of random line. Nab is the number of interfaces between grains of phase B and grains of phase A intersected per unit length of random line. The factor 2 arises in Eq. [2] because each interface B-B is associated with 2 grains of B-phase, whereas the interface A-B involves only 1 grain of B-phase. The calculations of contiguity do not require any assumption as to volume fraction, particle size, or particle shape. Fullman2 gives an expression for the determination of the mean free path between particles. The mean free path PB between grains of phase A, i.e., through grains or agglomerates of phase B, may be found from the relationship: PB =2fB/NAB [3] where fB is the volume fraction of phase B. The calculation of the mean free path is independent of grain shape and grain size distribution. The calculation of the number of contacts and of contact area requires assumptions of grain shape, grain size, and contact shape. In the case of uni-

Jan 1, 1959

By C. F. Lucks, W. D. Wood, H. W. Deem

Electrical ad thermal-conductivity measurements have been made on titanium and 6 titanium alloys. The following expression was derived for calculating thermal conductivity from electrical conductivity: K = 0.626 s T x 10-8 + 0.00497 where K = thermal conductivity, cal sec-1 cm-2 cm0C-1 s = electrical conductivity, ohm-]cm-1 T = temperature, deg Kelvin This expression gives calculated thermal conductivities that are not in error by more than 10 pct from the experimental values for A-55 titanium and the 6 alloys measured; namely, A-110AT, C-110M, C-130AM, Ti-6A1-4V, Ti-140A, and Ti-155A, which are representative of the presently available commercial a and a-ß titanium alloys. THERMAL conduction in a gas, liquid, or amorphous solid is accomplished by energy diffusion from molecule to molecule, a relatively slow process. For this reason, such materials have a low thermal conductivity. When a material is crystalline, there is in addition a heat transfer by a vibratory motion of the crystal lattice. It is the contribution of this lattice conduction that makes a crystal a much better conductor than a gas, liquid, or amorphous solid. Lattice conduction, however, does not account for the relatively enormous thermal conductivity of a metal. This is explained by the freedom of movement of valence electrons. These valence electrons drift in a metal in a direction toward a drop in electrical potential and, to a lesser degree, in the direction of a temperature drop in the metal. Since both the electrical and thermal conductivities of a metal depend upon the presence of free electrons, there should be some relatively simple relation between the two. Wiedemann and Franz in 1653 first discovered an approximate empirical relation between the electrical and thermal conductivities of metals at the same temperature. This ratio varies appreciably with temperature, and Lorenz later showed that by adding a temperature factor to the Wiedemann-Franz ratio the value of K/(s T) is constant, where K is the thermal conductivity, a the electrical conductivity, and T the absolute temperature. This Lorenz constant shows a greater variation for alloys than it does for pure metals, the ratio increasing slightly as the proportion of alloying elements increases. It has been found that a closer correlation between electrical conductivity and thermal conductivity can be obtained by means of an equation of the form K - A s T + B [1] where A and B are constants. In this equation the term AsT is the contribution of electronic conduction and B is the contribution of lattice conduction to the total thermal conductivity. EXPERIMENTAL MEASUREMENTS Electrical-resistivity and thermal-conductivity measurements on titanium and 6 titanium alloys serve as the basis for determining an equation of the K = AsT + B type for titanium alloys. Specimens—Table I shows nominal compositions of the 7 metals on which electrical and thermal conductivities were measured. The electrical and thermal-conductivity specimens for each alloy were taken from stock of the same heat and usually from adjacent sections of the same bar. All of the metals measured were in a mill-annealed condition. Methods—Electrical-resistivity measurements

Jan 1, 1959

By W. Rostoker, R. F. Domagala, R. P. Elliott

The phase equilibria of the Hg-Th system over the composition range 0-100 pct Th and temperatures up to 1000°C have been studied for a small-volume, closed system. The solubility of Th in liquid Hg is about 5 pct at 300°C and decreases sharply with decreasing temperature. Two intermediate phases occur, Hg3 Th and HgTh. The structures of these are hexagonal (nonideally close-packed) and face-centered cubic, respectively. The HgTh phase decomposes eutectoidally at 400°-500°C. The solubility of Hg in solid thorium seems to be negligible. AFULL-phase diagram for this system would have to be defined on temperature-composition-pressure co-ordinates. This paper describes the pseudo phase diagram of a closed system, that is, where the alloy enclosed in a small volume equilibrates with a vapor pressure of mercury dictated by composition and temperature. Because of the experimental difficulties in studying a system of this nature, many of the phase relations can only be sketched. Alloy Preparation Alloys over the full range of composition were made from triple distilled mercury and one of two grades of thorium. For the bulk of the work, a calcium-reduced metal in sintered pellet form of reported 99+ pct total thorium content was used. Arc-melted specimens of this thorium gave a hardness of 135 VPN. The microstructure showed small primary dendrites of ThO2. A number of alloy compositions were made with a high-purity, iodide-decomposition thorium metal. The are-melted hardness of a button of this material was 35 VPN. Although the microstructure of the arc-melted specimens showed no dendrites of ThO2, there was definite evidence of an unidentified phase enveloping the grain bound-aries. There were no distinguishable differences between the constitution of alloys made with the two grades of thorium metal. Under normal conditions thorium is not wetted by liquid mercury. The film of ThO2 on all thorium metal cannot be penetrated by either liquid or vaporous mercury. It was therefore necessary to comminute thorium in the presence of mercury under such conditions that oxide films could not reform on the newly exposed metal surfaces. This was accomplished by the use of a high-speed, carbide-tipped rotary cutter incorporated in a chamber purged with argon and connected at the bottom to a demountable Vycor bulb containing a weighed amount of mercury. This experimental device is fully described in a separate paper.1 Alloy compositions were calculated by weighing the empty bulb, the bulb containing the mercury, and the bulb containing the mercury and the thorium chips. Many alloys were analyzed chemically for thorium and/or mercury after subsequent homogenization; the agreement between analyzed and calculated compositions was invariably very close. Bulbs containing the requisite amounts of mercury and fine thorium chips were clamped off, removed to a sealing unit, evacuated and sealed. Amalgamation under these conditions proceeded rapidly even at room temperature. To insure homogeneity, the specimens were annealed to 300-400°C. Alloys containing less than 30 pct Th remained pasty after all treatments, indicating an equilibrium condition of liquid plus solid. Alloys with more than 30 pct Th were transformed into a dark powdery product. These latter specimens were annealed for times of up to 1 week to complete interdiffusion. Many of the alloy compositions are pyrophoric. On exposure to air they oxidize with considerable evolution of heat to a mixture of ThO2 and free mercury. It was mandatory that alloy specimens be handled in a "dry box" purged thoroughly with argon. All X-ray diffraction specimens were powdered, screened, and sealed in capillary tubes within the dry box. Experimental Procedures Thermal analysis experiments, useful only in the mercury-rich region of the system, were conducted with the alloys in their original containers. A reentrant thermocouple well formed an integral part of the bulb. These bulbs were heated in a silicone oil bath and cooled in a dry ice-acetone mixture. The rates of heating and cooling were slowed by immersing the specimen bulb in a larger tube containing silicone oil. This provided a suitable thermal lag. In all tests, pure mercury was run as a basic standard. While the invariant reaction at about the melting point of mercury was detected by thermal analysis, the heat effect at the liquidus was not sufficient to produce an inflection in the cooling curve. It was necessary to determine the liquidus temperatures at the mercury-rich end of the system by "breaks" in electrical reslstivity versus temperature curves for individual alloys. The apparatus for this purpose consisted of a pyrex tube about 2 in. diam and 12 in

Jan 1, 1959

By F. D. Rosenthal, F. J. Dunkerley, G. J. Mills

Activities, free energies, and heats and entropies of mixing of liquid Pb-Zn alloys have been obtained by the electrode-potential method between 400° and 650°C. The large positive deviations observed from Raoult's law are in agreement with the phase diagram, which indicates a wide immiscibility field. A vapor-pressure method was used to extend the activity measurements to 900°C, allowing the maximum of the immiscibility gap to be estimated by thermodynamic calculation. Data on the mono-tectic and eutectic points compare favorably with previously existing work. SEVERAL long-standing methods have been in use for the study of phase diagrams from measurement of the activities of the component metals.' The use of thermodynamic analysis for interpreting equilibria data is comparatively recent, however. Such analysis is usually undertaken by first evaluating the principal thermodynamic functions as, for example, the enthalpy, entropy, and free energy of the alloy constituents. These, in turn, quite often can be correlated with the interatomic potential energies and atomistics of the system, from which a clearer understanding of the causes leading to deviations from ideal behavior is gained. The present study of liquid Pb-Zn alloys is concerned with a determination of these quantities by electrode-potential and vapor-pressure measurements, using these values in calculations involving phase equilibria and to obtain a theoretical insight into an alloy system exhibiting strong positive deviations from ideal metallic solution. A considerable portion of the previously reported work is based on thermal analysis. Supplemented by optical studies of solid alloys, these techniques have revealed the essential nature of the immiscible mixtures that are formed. It is difficult, however, using the phase-

Jan 1, 1959

By T. J. Bosworth

The effect of hydrogen pretreatment of alumina, magnesia, and zirconia crucibles on reduced oxygen levels in iron charges has been studied. Hydrogen treatment of commercial high-purity magnesia crucibles was observed to produce as high as 70 pct reduction in oxygen content in iron melts. Hydrogen treatment of the commercial high-purity grade zirconia crucibles produced a 25 pct reduction in oxygen levels in iron melts. An average reduction of Knoop hardness of 47 pct was recorded on the iron charges melted in hydrogen-treated crucibles. On the basis of the experiments and the free-energy diagram, it appears that the major source of reducible oxygen to the iron charge is the suboxides and impurity oxides rather than the major oxide of the crucible. Suitable pretreatment of the crucibles to reduce and remove these oxides yields low oxygen levels in iron melted in the crucibles. DURING the last decade, attempts to produce more pure and uniform alloyed metals have brought about the development of many new melting techniques. Notable among these are vacuum-induction melting, inert and consumable-electrode melting, the cold-mold technique, and numerous techniques for removal of impurities by chemical reaction. However great the achievements in this field, metals must still be melted in contact with media of varying reactivity; i.e., gas, ceramic, and slag. Studies have been made to attain an understanding of the reactions that take place during melting, including slag-metal reactions and equilibria, equilibrium of hydrogen and water vapor, and carbon dioxide and carbon monoxide with oxygen in molten iron. These reactions have been treated quite thoroughly. There is one condition, however, that has been widely overlooked, and, to the author's knowledge, only cursive investigation has been made of it. This is the reaction between the ceramic crucible material and the iron charge. In recent years, Hadley and Bianchi' made a series of studies on hydrogen deoxidation of iron in magnesia crucibles. Bianchi2 studied crucible-FeO equilibria in the temperature range 1525°to 1650°C in high vacuum with, however, inconsistent results. Richardson and Jeffes3 in their series of articles on thermodynamic reactions in the making of iron and steel refer to Wentrup and Hieber's4 work on iron and aluminum deoxidation. Their pork included melting iron in alumina crucibles and measuring the aluminum and oxygen content in the iron. Because of the low values obtained, question has arisen of their analytical accuracy.3 Dastur and chipman5 obtained values on hydrogen-oxygen equilibrium in molten iron contained in alumina crucibles similar to those obtained in experiments in the present program. Hochmann6 studied removal of impurities in chromium irons in high vacuum. His results with respect to oxygen level in chromium-iron melted in magnesia crucibles are consistent with results we have obtained.

Jan 1, 1959

By O. F. Kammerer, W. E. Miller, D. H. Gurinsky, J. Sadofsky, J. R. Weeks

Zirconium and titanium inhibit solution mass transfer of steels by liquid bismuth, mercury, and lead. It is shown that in bismuth and mercury, these adsorb on the surface of the steels and subsequently react with nitrogen and possibly carbon from the steels to form inert, adherent surface layers of ZrN, TiN, or TiN + Tic. Data are presented which describe the condition under which thase deposits form. These inhibitors decrease the solution rate of iron into bismuth, and require a higher supersaturation for precipitation of iron from bismuth. USE of the low-melting heavy metals (bismuth, lead, mercury, and their alloys) as coolants has been limited because solution mass transfer of steels occurs in these liquids; i. e., iron dissolves in the hot sections of the heat transfer circuit and deposits in the colder sections. The rate of solution of iron and the temperature coefficient of solubility are sufficiently great to cause complete or partial stoppage by the deposition in the coldest section of a closed circuit in finite time, even though the actual solubilities are extremely low. In the development of the mercury vapor turbine by the General Electric Co., Nerad and his associates1 discovered that the addition of as little as 1 ppm Ti or Zr to magnesium-deoxidized mercury reduced the mass transfer of ferrous alloys by mercury to a negligible amount. Reid2 reported that titanium was detected chemically on the surface of steels contacted with this mercury alloy in amounts varying from 2.0 to 2.6 mg per sq in., the greatest amount being found in the hottest portion of the circuit. Reid stated that the titanium forms the intermetallic compound Fe2Ti by reaction with iron on the surface of the steels. This compound was presumed to be highly insoluble in mercury. More recently, El-gert and Egan3 have reported a greater than 100-fold reduction in the rate of mass transfer of a 5 pet Cr steel by liquid bismuth upon the addition of titanium (in excess of 50 ppm) and magnesium (350 ppm) in the liquid metal, during experiments performed in thermal convection loops* over the temperature differential 700° to 615° C. Also, Shep-ard and his associates' have reported that the addition of titanium to liquid bismuth and Pb-Bi eutec-tic produced a marked decrease in the rates of solution of both iron and chromium from type 410 steel capsules under static conditions. This inhibiting effect increased with repeated reuse of the capsules. Tests performed in this laboratory under carefully controlled conditions have shown that the addition of zirconium and magnesium, or titanium and magnesium, to liquid bismuth or lead greatly reduces the rate of mass transfer of chromium alloy steels and carbon steels in thermal convection loops with a maximum temperature of 550°C.5-9 The present paper will review the data obtained to date at this laboratory on the behavior of iron and steels in contact with liquid bismuth alloys containing titanium or zirconium, and will attempt to explain the role of the above additives in reducing solution mass transfer. Reaction between the Zirconium or Titanium Dissolved In Liquid Bismuth and an Iron or Steel Surface Reaction between Zirconium Dissolved in Bismuth and the Surface of Pure Iron-—A small pure iron crucible (analyzed by the supplier to contain 0.8 ppm N was contacted with bismuth containing approximately 0.1 pet Mg and varying amounts of a radioactive zirconium tracer. The crucible was then inverted at the temperature of contact. The thin residual layer of adherent bismuth was dissolved in cold, concentrated nitric acid. The crucible surface and the solidified bismuth were then analyzed for radioactive zirconium. An analysis of the activity loss on the crucible surface and the weight loss of the crucible during the nitric acid treatment showed that the acid treatment removed the zirconium that had originally been dissolved in the adherent bismuth, but not any zirconium that may have reacted with the crucible surface. The crucible was then pickled in warm aqua regia to remove all surface activity, hydrogen-fired at 600°C, and recontacted with a new liquid alloy. The results of the experiments contacted 1 hr at 450°C show, Fig. 1, a Langmuir-type adsorption with an adsorption free energy of approximately 17 keal per g atom Zr.5 This deposit was estimated to contain 1 atom of zirconium for each 7 to 8 iron atoms on the crucible surface, assuming a surface roughness factor of the pickled crucibles to be five. Increasing the temperature to 520°C caused consi-

Jan 1, 1959

By J. Chipman, T. P. Floridis

The equilibrium of gaseous H2O-H2, mixtures with liquid iron is used to establish the activity coefficient of dissolved oxygen as log f o = — 0.20 [%O]. Discrepancies in earlier work are explained or eliminated. Additions of cobalt, molybdenum, tungsten, and platinum increase the activity coefficient of oxygen whereas copper and gold decrease it. THE importance of dissolved oxygen as a refining agent in liquid steel has led to a number of studies of its thermodynamic properties. It is the purpose of this paper to examine the effects of a number of alloying elements on the activity of oxygen in the steel bath. As a preliminary to the study of the effects of alloying elements, it seemed desirable to examine certain minor discrepancies in the published data on the properties of oxygen in simple iron-oxygen solutions. The activity and free energy of oxygen in liquid iron were studied by chipman1 in 1933 by means of the reaction h2(g)+-o = H2O (g);K; = PH2O/PH2[% O] [1] The data were in fairly good agreement with calculations from results on the similar reaction CO (g) + O- = CO2 (g); K2 =P CO2/P CO [% O] [2] which had been obtained by Vacher and Hamilton2 as an incidental part of their study of the reaction of carbon with oxygen dissolved in the melt. It was found that the equilibrium ratio k1 was not a true constant but varied with the oxygen concentration in the manner shown in Fig. 1, which is copied from the original paper. This early observation has been refuted in subsequent work but is confirmed in the present paper, and an explanation of the discrepancy can now be presented. In Fig. 1, the two points on the extreme right were disregarded in drawing the

Jan 1, 1959

By J. Chipman, N. J. Grant, H. L. Bishop

Lime and dicalcium-silicate crucibles were equilibrated with molten iron and liquid slags containing iron oxide and small amounts of sulfur. The oxygen content of metal, iron oxide activities, and desulfurization values of the slags were determined in the temperature range 1530 to 1700°C. The influence of magnesia in the slag and the temperature dependence of the solubility of lime in liquid iron oxide and the ferric oxide content were established. The temperature contour of the liquidus surface of iron-silicate slags saturated with lime and dicalcium silicate was also established at 1600°C. THE importance of the role that slag composition plays in the refining of steel has been known for many years. Numerous studies have been made using actual plant data in order to establish the relationship between the composition of the slag and metal during the refining of a heat of liquid steel. These results rarely represent equilibrium conditions since completion of the various chemical reactions involved in steelmaking is seldom realized. In order to establish quantitatively the equilibrium conditions existing between the slag and metal, several laboratory studies have been conducted in the past 20 years to determine the reactions important in slag control. These investigations have included studies of simple liquid basic and acid slags as well as more complex slag systems which approach those commonly found during the refining of a heat of steel. Since most of the previous studies of simple basic iron-oxide slags equilibriated with molten iron were made in magnesia crucibles, it was not possible to establish the distribution of sulfur and oxygen between molten iron and slags consisting only of the three essential components, lime, silica, and iron oxide. This investigation was undertaken to establish the equilibrium conditions for simple lime-iron oxide and lime-silica-iron oxide slags. Accordingly, it was expedient to prepare crucibles both of lime and dicalcium silicate to establish the equilibrium conditions between molten iron and iron-oxide slags saturated with the refractory materials and free from other components. The only other studies of the equilibrium between molten iron and lime-saturated slags are those of Fischer and vom Ende, 1, 2 in which the solubility of oxygen was determined in an air atmosphere. The

Jan 1, 1959

By J. Chipman, N. J. Grant, H. L. Bishop

In a recent review1 of the iron-oxide activity of simple open-hearth type slags containing lime, magnesia, silica, and iron oxide, it was established that activity values were lacking in the range of slag composition most interesting to open-hearth operators. That is, laboratory experimental results were not available for simple slag compositions having basicity ratios ranging from about 1.5 to 4.0 and iron-oxide concentrations ranging from about 10 to 30 pct. However, in order to estimate iron-oxide activities for the range of slag compositions of interest to open-hearth operators, activity values were calculated using ionic concepts of slags by following the treatment of Flood and Grjotheim.2 A study of these data indicated that the desired slag compositions were probably not obtained due to the limited solubility of the basic constituents lime and magnesia. Thus, it was decided to make additional heats equilibrating molten carbon-free iron with slags containing MnO, P2O5, and A12O3 in percentages commonly found in open-hearth refining slags, and to examine the liquid slag field over a greater composition range than that of the simple slags studied previously. The ranges of the constituents used in the present study are summarized as follows: Metal Pct 0 0.070-0.201 PctMn 0.005-0.142 Slag Pet CaO 24.45-41.90 Pct MgO 3.23- 9.21 Pct MnO 1.13- 9.62 Pct FeO 20.08-48.7 Pet Fe2o3 2.23-10.14 Pct SiO, 3.51-28.50 Pct P2O5 0.23- 3.65 Pct A12O3 0.43- 3.38 The experimental procedure consisted of equilibrating the slag and metal in an induction furnace provided with a carbon-arc slag heater as described previously by Winkler and chipman.3 The data obtained were used to establish both the iron-oxide activity values and the activity coefficients for FeO and MnO in the open-hearth type slags. RESULTS AND DISCUSSION I) Iron-Oxide Activity of Open-Hearth Type Slags—The iron-oxide activities of various iron-oxide contents of the open-hearth type slags, as calculated from the oxygen content of the metal by the method of Taylor and Chipman, 4 are plotted against the molar ratio of bases to acids in Fig. 1. The data represent slag-metal studies carried out in the temperature range 1530" to 1700°C. For the purpose of this study, the constituents CaO, MgO, and MnO are assumed equal on a molar basis in their effect on the iron-oxide activity; and, PO2,5 is calculated as an equivalent to SiO2 and A12O3 on a molar basis. The total iron content of the slag is calculated to FeO and is represented by the symbol (FeO) The points presented in Fig. 1 represent the results of this investigation for iron-oxide slags containing between 1 and 8 mol pct MnO and less than about 2 mol pct each of A12o3 and PO2,5 The curved lines shown in Fig. 1 represent the results of the summary1 of the iron-oxide activities of simple slags of the system (CaO + MgO) - SiOz - (FeO),. The solid portions of the curved lines represent experimental data, and the broken portions represent iron-oxide activities calculated from ionic concepts of slags. The iron-oxide values of the open-hearth type slags of this study are in good agreement with the values of the simple iron-oxide slag system. Only a slight modification is indicated. The results of this study suggest that the line for 20 mol pct (FeO), should be lowered slightly in the basicity range 1.5 to about 3.

Jan 1, 1959

By F. D. Delve

RECENT studies by the author on the reduction of titanium from TiO2-bearing slags have been accompanied by difficulties that are attributed to

Jan 1, 1959

By B. Hilscher, P. Nayak, N. Yoon

"The mining industry is currently facing challenges with declining feed grades and is struggling to find solutions to improve the project’s economic value. By means of pre-concentration, ore sorting aims to separate the barren material from the valuable ore to reduce energy consumption and tailings generation, while increasing the feed grade, concentrate grade, mill recovery, and revenue. In addition, ore sorting allows the modification of deposit geometallurgy in order to allow the creation of an optimal mill feed.This paper evaluates the applicability and challenges of ore sorting by utilizing the results from four different mines, and reviews them in detail. The mines include two underground and two open pit mines that are base metal and precioius metal operations. In order to understand the applicability of ore sorting in these operations, initial rock-by-rock test results and different types of assays (atomic adsorption [AA], inductively coupled plasma [ICP], and fire assay) are utilized. Using the assay results, the grade recovery curves for ore sorting are generated and they are further improved by using and developing an ore sorting algorithm, which is discussed in this paper. The application and evaluation of ore sorting in greenfield and brownfield properties will also be discussed.The state of the art ore sorting technologies for both rock-by-rock and bulk sorting are reviewed in this paper. The future technologies on the horizon, including different combinations of sensors, are explained. The sorting technologies include, X-ray transmission (XRT), X-ray fluorescence (XRF), colour, infrared, electromagnetic, and laser induced breakdown spectroscopy (LIBS).IntroductionOre sorting is a sensor-based sorting technique introduced between the excavation stage and processing stage, where the unwanted waste is diverted to the waste dump and only the ore is sent to the mill for further processing. As a result, the quality of the material entering the mill is improved and the dilution of the ore is reduced. In greenfield projects, sensor-based ore sorting provides an opportunity to reduce the capital cost of the project and increase the return on investment (ROI). With most operations currently facing the challenge of finding a high grade deposit, having a sorting unit provides several advantages while keeping the cost at minimum."

Jan 1, 2017

By Yi Luo, Jian Yang, Hua Jiang

Surface subsidence events induced by underground longwall coal-mining operations can cause various disturbances to surface structures, ranging from integrity and stability to functionality problems. Highway bridges, as a kind of special road construction that can only tolerate smaller movements and deformations than road pavements, are particularly susceptible to severe influence caused by subsidence-induced ground movements and deformations. However, based on accurate subsidence prediction and correct influence assessments, efficient and effective mitigation and remediation measures can be designed and implemented to ensure the continuous service of bridges, safety of travelers, and smooth mining operations. In this paper, based on the predicted final and dynamic surface movements and deformations, the techniques to assess subsidence influence on the integrity, stability and functionality of bridge structures (such as decks, beams and abutments) are presented. A number of mitigation measures to protect bridge structures are recommended, along with an actual application case.

By Yi Luo, Jian Yang, Hua Jiang

Surface subsidence events induced by underground longwall coal mining operations can cause various disturbances to surface structures ranging from integrity and stability to functionality problems. Highway bridges, as a kind of special road construction that can only tolerate smaller movements and deformations than road pavements, are particularly susceptible to severe influence caused by subsidence-induced ground movements and deformations. However, based on accurate subsidence prediction and correct influence assessments, efficient and effective mitigation and remediation measures can be designed and implemented to ensure the continuous service of bridges, safety of the travelers and smooth mining operations. In this paper, based on the predicted final and dynamic surface movements and deformations, the techniques to assess subsidence influence on the integrity, stability and functionality of bridge structures (e.g., decks, beams, abutments, etc.) are presented. A number of mitigation measures to protect the bridge structures are recommended along with an actual application case.