Search Documents

By Guodong Li, Chenlin Wang, Zibiao Yu, Bo Xu

Abandoned coal mines have many underground space resources, such as roadways, shafts, and gobs. Among them, abandoned roadways are the best gas storage space for underground compressed air energy storage (CAES). However, CAES caverns have high air pressure and strict sealing requirements. Therefore, the stability and sealing of abandoned roadways under high internal pressure must be analyzed. Afterward, the suitability of abandoned roadways used for CAES caverns should be evaluated. In this study, the numerical simulation software FLAC3D was used to calculate the stress, deformation, plastic zone volume, and pore pressure of surrounding rock in an abandoned roadway under 10 MPa internal pressure. The influence of buried depth, surrounding rock grade, and in situ stress state on roadway stability and the effect of surrounding rock permeability on roadway sealing were analyzed. Results showed that the stress, displacement, and plastic zone volume of surrounding rock were affected by high internal pressure when the buried depth was less than 300 m, but high internal pressure had little effect on them when the buried depth was more than 300 m. The suitable range of buried depth was more than 300 m. The optimal choice of surrounding rock grade was I and II, followed by grades III, IV, and V. The optimal choice of in situ stress state was σH > σh > σv, followed by σH > σv > σh and σv > σH > σh. The sensitivity of the stability evaluation parameters was ranked in descending order as follows: buried depth, surrounding rock grade, and in situ stress state. When the surrounding rock permeability was less than 1 × 10− 14m2, the 24-h air leakage rate of the roadway was less than 1%. The suitable range of surrounding rock permeability was less than 1 × 10− 14m2.

May 23, 2023

By C. Newman

"Over the past decade, as conventional underground deposits have been depleted, mining operations have been forced to produce at greater depths and in more geologically and geometrically challenging conditions. As such, there has been a global increase in the application of cemented paste backfill (CPB) in tabular deposits utilizing open stope mining method with a delayed backfill placement. Despite the extensive use of CPB, many fundamental factors affecting the design of safe and economical fill structures are still not well understood. A critical issue in the design of backfilled stopes is the determination of stress states within the fill material itself as well as the surrounding rock mass. Analytical equations provide a means of quickly evaluating the effectiveness of a given design. However, in developing these equations large assumptions are implemented to simplify the design problem. It is important that one understands these simplifications as well as their effect on the overall design. This paper investigates common analytical equations utilized in the evaluation of single vertical backfilled stopes and their assumptions through comparisons to numerical modeling results. INTRODUCTION AND BACKGROUND As the mining industry continues to produce at greater depths and in more geometrically and geologically complex conditions, cemented paste backfill (CPB) has gained traction as a means of providing localized ground support in modern stope-and-fill mining operations. The application of CPB in stope-and-fill mining as a ground support material has led to the reduction of mine waste costs, while increasing both mine production and stability. In an attempt to achieve total extraction of the mining reserve, stope-and-fill mining operations often employ a primary-secondary excavation-support sequence (see Figure 1). In this practice, primary stopes are initially excavated and then backfilled in a two-stage pour; plug and final pours. During the first stage (plug), a CPB material with increased cementitious content is placed at the bottom of the stope providing a strong base from which to build a backfill structure as well as protect mine works from material breakthrough. Following placement, the backfill plug is allowed to cure to a given strength as designated by the mine design. Upon achieving the required cure strength, a less cementitious CPB material is used to backfill the remaining stope area. This is referred to as the final pour stage. With all primary stopes excavated and supported using backfill, the extraction of the secondary stopes commences as primary stopes are utilized as artificial pillars. While the application of CPB in a primary-secondary extraction-support mining sequence allows for a substantial increase in reserve recovery, it is imperative the mining personnel and planning engineers have a clear understanding of the material’s behavior and stress interaction with the surrounding rock mass to ensure the most efficient, cost-effective, and safe extraction of underground deposits."

Jan 1, 2018

By WenJun Dong

This paper presents the stability assessment of the steel pipe piles that are used to support a deadman beam to anchor an adjacent bulkhead wall. Finite element analyses are performed to assess the stability of the bulkhead wall and determine the required tie-back force to the pile. The piles are relatively close to the bulkhead wall such that their soil resistance wedge zones are not fully developed but truncated by the bulkhead wall. The reduced lateral resistance capacity of the anchor piles is determined by applying the Coulomb wedge method on the truncated soil passive zones between the pile and wall. Both the conventional soldier pile stability (in terms of force and moment equilibrium) and Winkler soil spring (for soil-pile-interaction) analyses are used to assess the stability of the anchor piles.

Sep 8, 2021

By M. Z. Emad, N. Abbas, Y. Majeed

Room-and-pillar mining is commonly employed for the extraction of rock salt in undergroundmines. Pillar stress is a major concern in these mines as it is directly related to stability and mineralrecovery. In this study a flat jack method was used to measure pillar stresses in three undergroundrock salt mines in Pakistan. The field work included determination of in-situ stress, in-situ elastic modulus, recording of field variables (pillar length and width, height and width of opening, opening width to height ratio, extraction ratio, and overburden height) and collection of salt block samples. The geomechanical properties of rock salt (uniaxial compressive strength, Young’s modulus, Brazilian tensile strength, and density) were also determined to estimate overburden stress, pillar strength, and factor of safety (both estimated and actual). It was found that the measured pillar stresses are proportional to the overburden stress values, with their magnitude ranging from 6.05 MPa to 11.97 Mpa, and the pillars were found to be stable. Regression analysis was performed to develop statistical models for in-situ stress and in-situ elastic modulus. Finally a quick guideline chart was developed to determine the suitable length of pillar for a given span and required level of safety.

Jun 5, 2023

By Hongwei Wang, PEIPEI CAO, Yongping Wu, JIANQIANG JIAO

In the fully mechanized top caving mining of steeply inclined, extra-thick seams with variable angles, the mechanisms of roof rock movement, failure, caving and filling are highly complex. This is due to the varying angle of coal seam in different areas, which makes rock–equipment stability control challenging. In this paper, the surrounding rock deformation and failure mechanisms, bearing structure of the overburden, and working characteristics of the supports are elucidated. The principle and key technologies of rock–equipment stability control are presented and applied to control the overburden of the regional failure and realize safe and efficient mining of the working face.

By T. Carageorgos

The removal of arsenic from process streams as ferric arsenate compounds is being practised by mining industries. Therefore, the solubility and stability of these solids is of considerable importance to the mining plants that have to keep the environment free from pollutants. There is some information on the solubility of the ferric arsenate compounds, mainly on scorodite, obtained from synthetic solution. However, there is not so much work on ferric arsenate compounds formed at high temperatures (175 - 230°C) during the leaching process. In the present work, the solubility of the ferric arsenate compounds formed during acidic pressure oxidation of arsenopyrite is presented. The results of the solubility tests showed that the ferric arsenate compounds formed at high temperatures (200 - 230°C) and high pressures (1034 - 1551 kPa 0,) released arsenic into solution in amounts less than 1.2 ppm and iron in amounts no higher than 1.0 ppm. So, they seem to be potential compounds for arsenic and iron disposal.

Jan 1, 1998

By R-H Yoon

The thin film pressure balance (TFPB) technique was used to measure the kinetics of thinning of single foam films and disjoining pressures in the presence of sodium dodecyl sulfate (SDS) and electrolyte (NaCl). The results were analysed in view of the Reynolds equation to determine the role of surface forces in film thinning. It was found that film thinning is controlled by surface forces at thicknesses below approximately 200 nm. It was also found that hydrophobic force plays an important role particularly at low SDS and NaCl concentrations. The values of the hydrophobic force constant (K232) estimated from the film thinning experiments were used to predict the disjoining pressure isotherm using the extended DLVO theory, which were found to be in excellent agreement with experiment. The TFPB technique was also used to measure the equilibrium thicknesses (He) of the foam films stabilised by a non-ionic surfactant, n-octanol, in the presence of NaCl. At a given ionic strength, He increased noticeably with increasing octanol concentration at very low concentrations. This observation suggests that hydrophobic force is at its maximum level in the absence of surfactant and decreases with increasing surfactant concentration. The results obtained with the single foam films were used to explain the stability of the three-dimensional foams.

Jan 1, 2005

By R. J. Mitchell

"High narrow backfills of significant strike length approach the stress conditions associated with a free standing wall but this lower bound design approach is not considered efficient for earth structures. This paper considers the design of high narrow backfills using upper bound limit analysis, retaining wall theory with backfill arching and centrifuge model tests. Complex toe support situations pertaining to operational factors at Falconbridge's Lockerby Mine are investigated. It is shown that the susceptibility of high narrow fills to toppling is much lower than anticipated from the retaining wall analysis and that toppling can be avoided by a suitable toe support. It is also concluded that adhesion between the fill and an adjacent pillar can markedly increase the stability of the fill. INTRODUCTIONFalconbridge's Lockerby Mine pillar projects will expose cemented tailings backfills to heights (H) up to 55 m. The exposed backfills may have strike lengths (L) greater than the heights but are relatively narrow, having widths (w) of up to 12 m. The bulk cement content of the fills varies from 8.3% (12.1 T:C) to 3.0% (33.1 T:C). Exposed faces may have up to a metre of overhang due to stope overblasting, as shown in Figure 1. These fills have a solids specific gravity of close to 3.0 and were placed at a pulp density of about 68%. The tailings have a fairly uniform grain size with 32% less than 0.075 mm (200 sieve) and about 12% slimes (less than 0.02 mm sizes). The fill exposed by early pillar removal will be backed by adjacent, near vertical, ore pillars. Future pillar removal may expose similar fills which are not supported by an adjacent ore pillar but which will be backed by either an open void or by uncemented backfill. Furthermore, these fills may be undercut when the pillar slot is driven, further reducing stability (case 3, Fig. I) or a wedge could be left to help support the fill (case 2, Fig . 1). This paper presents limit equilibrium analyses for these various backfill conditions in a 22: 1 T:C fill and com- pares the results to data from centrifuge model studies at a scale factor of A= 157 as indicated in Figure I. Prototype fills have a 6 m deep cone plug of 16:1 T:C which is accounted for in the comparison of centrifuge model test with analytical results."

Jan 1, 1989

Hydraulic backfill is generally retained in stopes using permeable barricades. Mitchell et al (1975), Mitchell (1992) and Grice (1989) have shown that under normal drainage conditions, barricades experience low levels of loading. Cowling et al (1988) have also shown that barricades are susceptible to piping failures if excess water has ponded on the upper backfill surface and if leakage of backfill from the barricades has occurred. During 1997, six hydraulic backfill barricades failed in four different Australian mines. Fortunately, in each case, the quantity of backfill slurry released was small, and no injuries to personnel nor damage occurred. Detailed investigation of two of the incidents showed that the primary cause of failure could be attributed to the delivery of excess quantities of transport water from the low-density slurry. For each of the incidents investigated there was evidence of the development of piping failures, which resulted in hydrostatic loading conditions on the barricades from the ponded water on the upper backfill surface. The circular failure surfaces in the barricades were characteristic of the application of point loading conditions. This paper discusses the circumstances that led to these incidents and analyses the modes of failure. The standards for the safe operating of hydraulic backfill systems are reviewed along with requirements for ongoing management and control. The design requirements of barricade construction are analysed and some appropriate guidelines introduced.

Jan 1, 1998

Hydraulic backfill is generally retained in slopes using permeable barricades. Mitchell et a! (1975), Mitchell (1992) and Grice (1989) have shown that under normal drainage conditions, barricades experience low levels of loading. Cowling et a! (1988) have also shown that barricades are susceptible to piping failures if excess water has ponded on the upper backfill surface and if leakage of backfill from the barricades has occurred. During 1997, six hydraulic backfill barricades failed in four different Australian mines. Fortunately, in each case, the quantity of backfill slurry released was small, and no injuries to personnel nor damage occurred. Detailed investigation of two of the incidents showed that the primary cause of failure could be attributed to the delivery of excess quantities of transport water from the low-density slurry. For each of the incidents investigated there was evidence of the development of piping failures, which resulted in hydrostatic loading conditions on the barricades from the ponded water on the upper backfill surface. The circular failure surfaces in the barricades were characteristic of the application of point loading Conditions.

Jan 1, 1998

By N. Sheikh

In galena flotation, lead ethyl xanthate, Pb(EtX)2, is precipitated and is physically adsorbed in the form of multilayers on the chemically adsorbed first layer of Pb(EtX). 1,2) The solid particles are coated with layers of Pb(EtX)2 in heterogeneous manner over surface areas possessing both anodic and cathodic character (3,4) It is anticipated that the mode of formation of Pb(EtX)2 and the number of ions present, together with stable or unstable by-product species, have great influence on the surface characteristics of galena. The information obtained from a study of these parameters may have important practical applications in flotation. Lead ethyl xanthate is sparingly soluble in water. The metal and xanthate ions released to the aqueous solution during its dissolution undergo various types of reactions depending upon the pH values of the system. Extensive work (5,6) has been carried out to elucidate the mechanism involved in acid decomposition of xanthate ions. Different decomposition paths (7,8) have been proposed for the hydrolytic decomposition of xanthate in neutral and alkaline solutions, The concentrations of lead ions vary due to a number of chemical reactions, regulated by the pH and the temperature of the bulk phase. The hydrophobic character of Pb(EtX)2 may change with the nature of chemical reactions. Some of the numerous by-product species in solution may adsorb on the solid and change the properties of surface film either favourably or adversely. The flotation performance of galena, therefore, may depend to a considerable extent on the physical and chemical stabil¬ity of Pb(EtX)2 layers. Since little work has been reported in literature dealing with the stability of Pb(EtX)2 and its correlation with the flotation of galena, attempts have been made In this study to evaluate the behaviour of freshly formed Pb(EtX)2 in aqueous systems at various pH values.

Jan 1, 1971

By M. B. Kahle, A. D. Pernichele

Four types of slope failures in waste dumps are recognized debris flow, foundation failure, edge slump, and blowout. The first three types, although at times causing considerable damage to property and interfering with mine operations, are not usually dangerous to personnel because of their slow rate of movement. The fourth type, the blowout, is the most dangerous because of its explosive mode of failure and lack of forewarning. The December 1969 failure at Verona dump is presented as an example of a blowout. Data from piezometer holes indicate that the blowout was due to perched leach solutions near the face of the dump. The level of water in this zone is very closely related to the rate of leach water application on the dump. A detailed analysis of core samples indicates that the impounded water was perched on a zonal accumulation of jarosite which is associated with a buried dump surface. Drain holes proved successful in controlling perched leach solutions in the critical zone near the face of the dump. Monitoring of the water level in the perched zone is considered essential in preventing blowouts. The use of drain and piezometer holes has allowed an increase in the rate of water application on the dump while preventing additional failure.

Jan 1, 1972

By Ljiljana Solujic

The need for the removal of mercury from the precious metals extraction circuits may be influenced by process, environmental, as well as by occupational hazard reasons. In these circuits mercury is mainly present as cyanide complexes. The effectiveness of any stabilization method will be influenced by the high thermodynamic stability mercury-cyano species exhibit in an aqueous solution. In this study, we have investigated the utility of the trisodium salt of trimmercapto-s-triazine (TMT) for precipitation of mercury from the corresponding cyano-complexes. The influence of pH molar ratio of TMT to Hg, coagulant and flocculant additions, excess of free cyanide, as well as the presence of other metal-cyano species on the effectiveness of mercury precipitation were investigated in detail. Also, a "teal world" precious metals mill effluent initially containing ~7 ug/mL (ppm) of Hg was treated and A was found that greater than 99.8% of the mercury was removed from the solution as am insoluble Hg/TMT complex.

Jan 1, 1996

By R. M. S. Häggblad

The article deals with stabilisation and regeneration of Ce02 and Ce02/Zr02 based Pt water gas shift catalysts, subject to high initial deactivation. The reaction gas species effect on the catalyst deactivation was investigated by H2-TPR. Activity measurements enabled the effect of different promoters, some added to the Ce02 based catalysts and some to the Ce02/Zr02 based Pt catalysts, to be investigated. The catalysts were also characterised by BET and CO-TPR. Deactivated catalysts activity was restored by using various regeneration methods. Of the two selected carriers the Ce02/Zr02 based Pt catalyst showed the highest resilience to deactivation. For the two different carriers, Ce02 and Ce02/Zr02, Wand Re were the best promoters when the catalyst was subject to deactivation. Experiments with Hr TPR indicate a fast initial change in the platinum oxides concentration and composition. The CO-TPR was used to make conclusions about the various regeneration effects of water and oxygen on the catalyst. Finally it is suggested that not one deactivation mechanism is possible and which mechanism that dominates is dependant on the catalyst and the reaction gas composition.

Jan 1, 2005

By B. Zeifert, C. Martínez-Morales, A. Romero-Serrano, A. Pineda-Rivera, H. Martínez-Gutiérrez, G. Diaz-Sandi

In this work, the effects of CaO/SiO2 ratio and the FeSO4 and FeS2 contents on the stability of the mineralogical species in chromium-based slags were studied. The chemical stability was evaluated by leaching with an acid solution. The main Cr-compounds in slags with FeSO4 and CaO/SiO2=1 were FeCr2O4 and Ca3Cr2Si3O12, while Cr3S4 predominated in slags with FeS2. The slags with CaO/SiO2=2 mainly contained CaCr2O4. The highest Cr concentration levels in the leaching liquors corresponded to slags with CaO/SiO2= 2, and the lowest Cr concentration corresponded to slags with high FeSO4 or FeS2, owing to the stable binding of chromium in the compounds FeCr2O4, Cr3S4 and FeS•Cr2O3.

Jan 1, 2011

By Helene Kennedy, Josef Macsik, Yvonne Rogbeck, Gregory Makusa, Göran Holm

"Constructions activities in cities often imply large volumes of surplus material which could be treated by stabilization for re-use in new geotechnical constructions. Modification of dredged sediments by e.g. stabilization/solidification (s/s) is an example of sustainable handling option implying dredged contaminated sediments to become a potential resource for civil engineering constructions. The SMOCS project (Sustainable Management of Contaminated Sediments) within the Baltic Sea Region Programme 2007-2013 has developed a guideline based on a sustainability approach free to download at www.smocs.eu. The paper presents key issues in the guideline and highlights the importance of performing a field test as part of the design process. Two field tests with s/s-treated dredged sediments for new port areas are presented. Strength, permeability and leakage properties of s/s-treated contaminated sediments make beneficial use in geo-constructions possible. The influence of possible physical/chemical deterioration processes on the durability has been studied showing that freeze/thaw cycles might degrade the monolith of s/s-treated sediments. Consequently s/s-constructions shall be below freezing depth. Other deterioration processes such as salt and sulfate penetration were found of minor importance. Research is on-going to study the influence of and how to cope with freeze/thaw cycles on the long-term properties.BACKGROUNDConstructions activities in cities often imply large volumes of surplus material which could be treated by stabilization for re-use in new geotechnical constructions. The mechanical and environmental properties of the contaminated sediments could be modified through the stabilization/solidification method (s/s method) and provide a potential resource for civil engineering constructions. The SMOCS project (Sustainable Management of Contaminated Sediments) within the Baltic Sea Region Programme 2007-2013 has developed a guideline on management of contaminated sediments based on a sustainability approach. A field test on the application of the stabilization/solidification method for treatment of dredged soft contaminated sediments was implemented in the Port of Gävle, Sweden. The treated sediments were beneficially used as fill material in the new port area replacing ending natural resources."

Jan 1, 2015

By Joe B. Rosenbaum

Fine-sized mineral wastes discarded by ore milling plants require stabilization to prevent air and water pollution. Methods devised for achieving this stabilization include physical, chemical vegetative, and combination procedures. Although vegetative reclamation is preferred to physical and chemical stabilization, it is difficult to achieve because the wastes are sterile, contain deleterious inorganic salts, and lack the essential nutrients and physical characteristics required for sustaining vegetative growth. Nevertheless, recent research has developed methods for producing vegetative growth on all but excessively acidic, basic, or saline tailings at costs ranging from $100 to $650 per acre. This report summarizes effective procedures developed for vegetating average tailings, the cost differential between the various methods, and suggests procedures that may be applicable for achieving stabilization of pyrite-containing wastes that may oxidize and become excessively acidic. The use of buried layers of sewage sludge to prevent this acidification is discussed.

Jan 1, 1972

By Edwin Ludlow

T HE OPEN FORUM on this subject called by Mr. Hoover at the recent meeting of the Institute' brought out a large number of very able papers, and a very full discussion of all the problems involved. The criticisms of the bituminous industry were: 1. That it was over-developed with the possible output nearly 50 per cent. in excess of the present requirements; that during the summer there were plenty of cars and no orders, and during the winter there were plenty of orders but no cars. 2. That the mines were not properly developed from an engineering standpoint, and that the recovery of the coal varies from 50 per cent. to 95 per cent. 3. That this industry, employing over 600,000 men, could, if running full time, release 100,000 men for other work. 4. That the studies made by the engineers of the Fuel Administration showed that the cost of production increased with a loss of time and that with a 50 per cent. operation the increase in cost was about 40 per cent.

Jan 1, 1920

By U. Oko

The cause and the effect of disposing of tailings water from sulfide ore milling operation were examined. Dissolved metallic ions as well as dissolved sulfur-oxygen compounds (polythionates) can prove injurious to life in water streams. Polythionates originate in alkaline flotation circuits and may cause a severe drop in the pH of stream waters. It is proposed that a suitable "aging" period be allotted to tailings water to ensure complete conversion of polythionates to sulfate prior to neutralization and clarification treatment. Discharging alkaline solid-free tailings water without aging will cause downstream acidification. Artificial oxidation of tailings water can be economical only if the concentration of thiosulfate in solution is low. When the concentration is high, it is possible to reduce the concentration greatly by first acidifying the solution, because at a pH below 4 thiosulfate in water reacts to produce a precipitate of elemental sulfur and higher order polythionates. The residual polythionates can then be oxidized at great savings by natural aging or by chemicals such as ozone, chlorine, or peroxide. Chlorine may be an economical reagent for converting polythionates to sulfuric acid but the residual organo-chlorinated compounds can prove to be toxic to aquatic life. Ozone and hydrogen peroxide which do not leave a residue are preferred oxidizers.

Jan 1, 1976

By Mark Kramer

This paper is limited to treatment of bottom and fly ash waste resulting from WTE and RTE Cogeneration plants, commonly known as trash burners. The body of the paper defines waste generation and conventional treatment schemes. This paper does not identify a best treatment, however, it does offer a general perspective of the treatments to lead the reader to further investigation. Advantages and disadvantages of the ash treatments Is discussed in each treatment section.

Jan 1, 1996