Search Documents

By Michael Clar

Total suspended solids (TSS), generally referred to simply as sediment, is one of the four major parameters of water pollution associated with surface mining activities. The other three para¬meters are iron, manganese and pH. Currently the Environmental Protection Agency (EPA) is in the process of developing and implement¬ing effluent limitations for these pollutants pursuant to section 301 of the Federal Water Pollution Control Act Amendments of 1972, 33 USC 1811.1 To date, effluent guidelines for existing point sources have been published, and guidelines for new sources are forthcoming. The effluent limits which have already been developed for TSS have been subjected to some controversy.1 Some industry spokesmen have indicated that they may be unable to meet these effluent limitation guidelines for TSS. The industry claims that in certain areas the suggested limit is unattainable since high suspended solid loads already exist in streams due to numerous and various sources of nonpoint pollution which include agriculture, silviculture and urban construction for which no TSS effluent limits have been set. An opposite viewpoint asserts that the TSS limitations are too lenient since permit data from the Regions (U.S. EPA Regions) indicates present compliance for several companies under more stringent TSS limits. The experience at the Centralia mine in Washington is one example.2

Jan 1, 1977

By G. W. Poling

Sedimentation behaviour of siliceous mill tailings derived from a magnetite-chalcopyrite ore in fresh water, fresh water - sea water mixtures and full-salinity sea waters are compared. Results of batch settling tests are presented in the form of settling curves and solids flux curves. The addition of a few per cent of sea water markedly enhanced the zone sedimentation rate due to particle agglomeration caused by a reduction in zeta potential of the suspended solids. The presence of a small amount of residual, previously magnetized magnetite in the tailings also enhanced agglomeration and sedimentation. The significance of these results to submarine disposal of mill tailings is discussed.

Jan 1, 1973

By A. V. Bauman

"Important for thickening processes is the ability of slurries to form under certain conditions aggregation and sedimentation stable systems. Substantial part of difficult to sediment solid particles in such systems may be in colloidal state. The technique to study the sedimentation and aggregative stability of the slurry developed by the author with co-authors makes possible to define kinetics of changes in the aggregative stability of the system with solid phase varying concentration in it and produce data on sedimentation stability of the system in preliminary investigation of the thickening process. Research of aggregative and sedimentation stability of the slurry complement standard methods of laboratory studies to prevent errors in development of water-slime thickening balance and water circulation to design new and upgrade existing processing plants. Statistical analysis of process audits of more than one hundred upgraded and newly commissioned processing plants carried out in recent fifteen years showed that more than two-thirds of problems arising in commissioning the processing plants are associated with misdesign and errors in thickening and water circulation system. Among the main reasons of process design failures are: non-conformity of actual characteristics of the raw material to design characteristics, low quality of preliminary studies at the stage of sedimentation process simulation, design failures, wrongly selected equipment for the thickening and water circulations systems. As of today a number of problems associated with laboratory studies of sedimentation process, first of all, with interpretation of precipitation curves produced at the stage of laboratory refinement of the thickening process have been pinpointed. (Bauman A.V. Outstanding issues in design of thickening and water circulation diagrams in processing plants // Ore processing. 2016. ?3 P. 58-62) ?????? ?.?. ?????????? ??????? ?????????????? ???? ???????? ? ??????????? ?????????????? ??????. // ?????????? ???. 2016. ?3. ?. 58-62))"

Jan 1, 2018

By S. Nafisi

Permanent mould casting may be regarded as a near net shape manufacturing process where simple to very complex shaped engineering components are fabricated with high degree of precision in a metallic mould, In this group, High Pressure Die Casting (HPDC), have attracted more attention because of its production rate, where both liquid and semisolid metals (SSM) can be cast with high degree of precision and versatility. The SEED process, Swirled Enthalpy Equilibration Device, the new process for semi solid metals slurry production route, consists of two steps: The initial step involves extracting specified amount of heat from the molten metal to generate liquid-solid slurry, i.e, mushy structure, followed by drainage of remaining liquid to produce a compact free standing feedstock for rheocasting operation. In this paper, microstructural evolution during the process and some initial casting results of automotive components an also reported.

Jan 1, 2005

By Herman Mendoza, Luisa Ciriaco

An investigation of the seeding mechanism using heterocoagulation and the Derjaguin - Landau - Verwey - Overbeek (DLVO) theory of two pure minerals is the objective of this study. The seed was silica with modal diameters of 4.529 µm (fine particles) and 5.216 µm (coarse particles) and the test powder was hematite with a modal diameter of 0.883 µm. Parameters included variations in the concentration and particle size of silica. Both particles were first subjected to size determination and settling tests via Stoke’s Law. The silica-hematite system was then suspended in 0.001 M KNO3 electrolyte solutions where pH was adjusted. Afterward, the suspension was agitated and was allowed to settle at different time intervals while obtaining turbidity readings. Results through settling time and turbidity vs. pH graphs indicate that maximum heterocoagulation occurs from pH 2 to 5 while minimum heterocoagulation occurs from pH 6 to 7. At these pH levels the zeta potentials of silica and hematite are negative and positive, respectively. On the contrary, repulsive forces dominate the system from pH 8 to 11 due to the particles’ negative zeta potentials. Furthermore, the attachment of hematite to silica increases when the parameters become larger thereby increasing the effectivity of heterocoagulation at acidic to neutral pH levels.

Jan 1, 2014

In Canada and other countries, legislation dealing with accurate factual disclosure for mining projects is being expanded to include more metallurgical design information. Grinding characteristics, metallurgical recovery of contained metal and environmental hazards associated with tailings disposal will be part of the Canadian package. This paper will examine only that portion of the plant design standard practice that relates to grinding ? in SAG mills and ball mills that grind ore from as received crushed material to final ground product that is fed to downstream plant recovery processes. Since grinding plants represent a significant portion of the overall concentrator cost, accountability in grinding design should no longer be left to chance, opinion, or hidden proprietary information. This is the 21st century. It is reasonable to expect that a factual basis will be needed so that a Qualified Person (QP) reviewing the grinding mill design can understand it. That will also involve how many and what quality of samples are taken to define the characteristics of the deposit, the accuracy of the tests used to measure ore hardness and the method by which the dimensions and power of the mills are determined. If these criteria are not met, the QP may have no choice but to call attention to the lack of convincing information regarding the grinding mill design for the project. At the same time clients are expected to demand getting the correct design information at a cheaper price, results in a more timely way, and accurate design to the point where the risk of tonnage shortfalls are reduced or eliminated. Tables will be presented to show how this can be done to current standards using existing technologies. At the same time it is acknowledged that current standards are ill-defined and that to achieve consensus among those involved in SAG mill design work, it may require that a consortium funded project be set up to establish what tests and methods for grinding design are suitable to meet the new standards for metallurgical disclosure. By running parallel design methods on several major projects over a period of 5 years, the process of how to design grinding circuits will be better understood because the projects will start at the design stage, include procurement of the mills and will end with a benchmark test on the plant. Selecting the samples and the best schedule for doing test work on core samples submitted and mill design, will be discussed in this paper. The issue of completing the grinding design in time for early procurement decisions is on the critical path for most major projects. Discussions between mining engineers, geologists and process engineers are needed early in the development cycle, at the scoping study level (SS), preliminary engineering assessment (PEA), prefeasibility study (PFS), and at the feasibility study stage (FS), to ensure that proper planning for design sample selection is done. Using adequate sampling and testing methods in a timely way allows early procurement of the grinding mills and minimizes project risk.

Jan 1, 2012

By Mohamed Elgouhary, Carol L. Tasillo, Daniel Koziol

"The Bolivar Dam, located near the Village of Bolivar, Ohio is one of a system of dams designed to provide flood control and water conservation in the Muskingum Watershed. The Bolivar Dam is a “dry dam” that only impounds water during flood events. In order to address problematic seepage, which negatively affects the structural stability of the dam, the U.S. Army Corps of Engineers (USACE) designed a partial-depth and partial-length Seepage Barrier Wall (SBW) through the upstream slope of the dam. For this project, TREVIICOS constructed a 36 in (914 mm) positive SBW by plastic concrete panel wall method and excavated using hydromill and clamshell equipment. The plastic concrete was manufactured on-site, which allowed for enhanced quality control and prompt service. This required the installation, commissioning and operation of a concrete batch plant on-site. This paper presents the challenging aspects of the design, manufacture and placement of the plastic concrete for the SBW in order to meet contract strength and permeability requirements as well as workability requirements necessary for tremie concrete placement.Project General InformationBolivar Dam is located in Northeast Ohio (Fig. 1). It is one of a system of sixteen dam projects designed to provide flood control and water conservation in the Muskingum Basin, which covers 20 percent of the State of Ohio (Fig. 2). Bolivar Dam is on Sandy Creek, a tributary of the Tuscarawas River.The Dam has been constructed, operated and maintained by the USACE, for the Muskingum Watershed Conservancy District. Its construction was completed in 1937 and it has been in operation for flood control since 1939.Bolivar Dam is a rolled earth fill dam, with a typical embankment section made of a central impervious core flanked upstream and downstream by a pervious outer shell with downstream rock toe. The embankment has a maximum height of 87 ft (26.5 m) and a crest length of 6,300 ft (1,920 m), and is comprised of the main embankment starting on the left abutment of about 1,500 ft (457 m) heading to the Northeast, followed by the terrace embankment of 4,800 ft (1,463 m) heading to the North. An upstream impervious blanket extends up to 500 ft (152 m) upstream of the dam along the majority of its length. The outlet works are to the left of the embankment, and consist of an intake structure with six gates, followed by two outlet conduits that finish in a stilling basin. To the left of the outlet works is the uncontrolled emergency spillway, which was doubled in width to 540 ft (165 m) in 1989, and excavated material utilized for construction of a stability berm against the upstream face of the main embankment. A concrete parapet wall was also installed along the upstream side of the crest during this work. In 1982, a toe drain, downstream filter berm and line of 35 relief wells were installed. The filter berm was recently extended an additional 200 ft (61.0 m) downstream and granular filters were placed over an approximate 2000 linear ft (610 m) reach of the lower terrace slope. (Fig. 3)."

Jan 1, 2016

By K. E. Robinson

During operation of tailings impoundments, water is lost through decanting, evaporation and seepage. Techniques have been developed to regulate or control each of these components. Collectively implemented, these techniques form the basis of tailings impoundment management. Regulation of the rate and level of decanting influences the size of a free water pond, and, thereby, the amount of evaporation and seepage, which are both area-dependent. Conversely, the encouragement of seepage and/or evaporation could also be used to reduce decanting requirements. Management of one of the components of a tailings impoundment's water balance is reflected in changes in the other components. The seepage component has the greatest potential impact on the environment, and consequently requires the closest scrutiny. Water percolating through tailings backfill transports heavy metals and other dissolved solids from the impoundment into the local groundwater regime. Depending on the seepage volume and concentration of contaminants, seepage from impoundments could exceed environmentally tolerable limits. Once mobilized, seepage-borne pollution is much more difficult to treat, mainly because of the problems in collecting the diffusive transportation medium. Pollution abatement measures relative to tailings impoundment seepage depend on seepage prevention or reduction. Seepage control measures include constructing barriers to flow, pump-back systems of interception and restricting the supply of water available for seepage.

Jan 1, 1987

By J. Jeremy Burden, Bruce S. Brown

A major question in the design and permitting of a tailings storage facility is the quality and quantity of seepage which will occur from the base of the tailings facility into the underlying foundation and groundwater regime. A corollary to this is what liner system, if any, is necessary to protect the groundwater regime from unacceptable contamination. Modern tailings storage facilities are generally designed as drained tailings deposits whereby all free water is removed from the facility by decant, drainage and evaporation. This removes the source of on­going seepage and allows for efficient and timely reclamation of the facilities. Quantifying the residual seepage from the base of the tailings deposit is complicated due to the following factors:

Jan 1, 1992

By Eduardo Velasco, Paz Navarro, Alfonso Navarro, Claudio Cimiotti, Alejandro Sanz, Nick Karlin

The LA Effluent Outfall tunnel is a 7-mile long, 18' internal diameter, secondary treated effluent discharge tunnel currently under construction by Dragados USA for the Los Angeles County Sanitation District No. 2 (LACSD). The purpose of this tunnel is to add redundancy and increased capacity for discharge of secondary treated effluent from the LACSD’s Joint Water Pollution Control Plant, located in Wilmington, California within Southern Los Angeles County. Current discharge from this facility flows through two existing tunnels of 8' and 12' horseshoe profile, constructed in 1937 and 1958, respectively. When the new tunnel is complete, it will add an additional capacity of 670MGD in peak wet weather flow conditions. Geology of the roughly 7 mile long tunnel was divided into six reaches by the contract documents. Tunnel Reaches (TR) 1 to 3, comprising 19,550' will be excavated in alluvial sands of the San Pedro and Lakewood formations, with cover ranging from 45 to 90 feet. In this reach the tunnel intersects the seismically active Palos Verdes fault Zone. TR 4 is a 1,600' transitional zone between alluvium and the rock formations of the Palos Verdes (PV) Hills, comprised mostly of Malaga Mudstone. TR’s 5 and 6 total 15,591', and are within the rock formations of the PV Hills with overburden ranging from 315' to 475'. The primary constituent of the PV Hills is Altamira

Jun 13, 2021

By Stefan Mede

Robot Supported Moulding—this is the name of Herrenknecht Formwork’s entry to the world of automated segment production. What had been considered impossible for a long time, has been achieved by Herrenknecht experts together with the Swiss company Marti AG: unmanned segment production on the working line. The moulds open and close autonomously with the help of a hydraulic system. A robot cleans and greases the moulds at one work station and inserts the injection sockets at another. The next step will include further automation and digital networking of all processes from production to installation in the tunnel.

Jun 13, 2021

By K Seddon

Segregation of tailings on deposition can occur as a result of a) sub-aqueous deposition, and b) sub-aerial deposition at lower solids concentrations (i.e. when the solids concentration is less than the segregation threshold). The effects are likely to be more pronounced in the case of subaqueous deposition.This paper presents the results of an investigation of a sub-aqueous tailings facility.Data from the investigation show extreme variations in particle size and density compared to test results for non-segregated ‘all-in” tailings. The results indicate that on segregation both the fine and coarse splits tend towards a well sorted (poorly graded) mix, and both have significantly lower consolidated density than the all in tailings. This result is reasonably well known for the case of the segregated fines (“slimes ponds”) but less appreciated for the coarse fraction. The results suggest that if the effects of segregation are not allowed for, the overall density of the deposit can be seriously over-estimated at the design stage. Also the quantity of water retained in the tailings can significantly influence water recovery and water balance results.CITATION:Seddon, K, 2018. Segregating tailings – effects on density and water retention, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 299–308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Donald Wagstaff, D. Scott Scovire

The Coeur Rochester Mine is the largest primary silver surface mine in North America. Throughout its 17-year life, gold and silver grades leaving the tertiary crusher have typically been, on average, slightly below the mined bench grades as determined by blast hole assays. On a project-to-date basis, this grade variance is well within industry standards. While these variances are acceptable, mine personnel continue to study ways to further minimize the grade differences. One suspected cause for lower than expected head grades are ore loss and dilution resulting from blast-induced shot movement. In regard to grade control, the underlying design principle for non-electric blasts is the generation of uniform movement of the blasted rock material. Using one or two uniform directions of initiation, ore control methods at Rochester currently include adjusting flag lines on the muckpile in an attempt to account for displacement from original, pre-blast locations. To improve upon standard non-electric blasting practices, a series of evaluation blasts using an electronic initiation system (Orica i-konTM) was conducted in the summer of 2002. The primary objective of the evaluation blasts was to design shots that would segregate the ore and waste blocks into distinct muckpiles. Due to surface delay burning front limitations, truly effective ore and waste segregation blasting is difficult to accomplish with non-electric initiation systems for all but the most basic of ore geometries. The electronic detonator evaluation blasts produced visible boundaries in post blast muckpiles, identified by troughs or low areas, that closely matched the actual locations of pre-blast ore control flag lines based on blast hole assays. By blasting the ore and waste into distinguishable piles that were flagged and excavated accordingly, it is believed that blast-induced ore loss and dilution was reduced.

Jan 1, 2004

By K. Johanson, M. Hubert, C. Eckert, D. Ghose

The mining industry routinely processes material with different particle sizes. Coal, nickel ore, copper ore, lignite, shale, and phosphate ore are all examples of materials with wide particle size distributions. It is often assumed that these materials are homogenous and that any particle size distribution has the same chemical activity and composition. It is entirely possible, and quite likely, that chemical composition is a function of particle size distribution. In addition, particle size distributions in ore materials are often responsible for the difference in flow behavior in process equipment. This is evident in coal electrical production facilities. Fine coal may have the same ash content, sulfur content, and BTU value as coarse coal. However, all electrical production facilities know the extreme flow problems that result when attempting to handle wet fine coal. Segregation of these bulk materials is an important issue that must be understood to prevent these cohesive flow problems. Additionally, fertilizers are mixtures of particles with different shape and sizes. These mixtures must remain homogenous to optimize fertilizer performance. Segregation leads to poor product quality. This paper presents a method of measuring the magnitude of sifting segregation occurring in bulk material and the relationship between the strength of the bulk material and the separation tendency. It shows an inverse relationship between the yield strength of the material and the bulk segregation.

Jan 1, 2004

By Bernardo J. Jiménez Vega, Edy L. T. Montalvan

During the last phase of the Circunvalacion Norte project in San Jose, Costa Rica, preliminary designs for an underpass structure of over 16 km (10 miles) considered drilled shafts as an earth retaining system. Since the project’s execution was delayed and close to the deadline, it was necessary to optimize this structure, with the drilled shafts being the most critical aspect. The key element in order to obtain an improved design was characterizing the job site with a specific site study for seismic demand, and the use of advanced numerical modelling, considering soil-structure interaction. The site investigation comprised the CPT, PMT, MASW geophysical tests, deep exploration drilling, and triaxial compression tests. The terrain was modeled using an advanced constitutive model with hardening plasticity calibrated from the triaxial tests. Plaxis software was used to calibrate the seismic model for the terrain and for the dynamic analysis. Two conditions were considered for the retaining structure: free-head and fixed head. A parametric study with drilled shafts of 1.0 m (3.3 ft) and 1.2 m (3.9 ft) in diameter, and center-to-center spacing of 1.3 m (4.3 ft) and 3.0 m (9.8 ft) was conducted in order to obtain an optimized structure. For each condition of the drilled shaft wall, the computed deformations were compared for two spectrum designs: site-specific spectrum and seismic code generic spectrum. Finally, a dynamic analysis was performed to check the performance of the drilled shafts with optimized spacing using a control earthquake. Based upon seismic performance curves, the analysis showed the possibility of greater spacing for the drilled shafts compared to the original design, obtaining a 32% reduction in the total length of the drilled shafts in the project.

Oct 1, 2022

By Don Deardorff, Ke Yang, Yingcai Han, Ken Sorensen, Robert Kruger, Mark Petersen, Diane Fiorelli, Larry Goldfarb, Kathryn Petek, Kwabena Ofori-Awuah

Design of deep foundations for lateral loads requires an understanding of soil-foundation-structure response during loading. Lateral loads on a deep foundation (piles) could be due to earthquakes, winds, waves, and/or machine vibrations. Over the years, analysis of response of piles due to lateral loads evolved from closed-form solutions to p-y methods to strain wedge to finite element/finite difference modeling. Although analysis of lateral response of piles and shafts is routinely performed, there is no single guidance document and/or standard for design and testing. Several different analytical methods are available for the analysis, and the resulting design can result in significantly different responses which can create confusion. This is especially true for analyzing and designing piles in potentially liquefiable soils with lateral spread issues under seismic conditions.This guidance document is intended to assist geotechnical engineers, pile designers, and contractors in analysis, design, and testing of piles and drilled shafts for lateral loads. This document discusses the background of different analytical and testing procedures and presents the recommended methods for analysis, design and testing of piles for lateral loads.Chapter 1 defines the different kinds of lateral loads to which a single pile or pile group may be subjected. This first chapter also presents different types of piles used to resist lateral loads.Chapter 2 discusses geotechnical issues related to lateral pile design such as liquefaction and lateral spreading and other non-seismic issues. Also addressed in Chapter 2 is geotechnical site characterization (as related to lateral loads) in terms of site investigation, in-situ testing, geophysical testing, laboratory testing, and estimation of soil/rock properties.Chapter 3 discusses the background and available analytical methods and tools for the analysis and design of single piles and drilled shafts. Several methods of analyses from closed-form elastic solutions to the finite element/finite difference solutions and their applicability are discussed. Available commercial computer software packages for analyzing single piles and drilled shafts are also presented.Chapter 4 expands the discussion of single piles and drilled shafts into the analysis and design of pile groups. In addition, group effects, resistance of pile caps, results of previous experimental and analytical studies, and available analysis tools and software for pile groups are discussed.Chapter 5 presents the issue of lateral resistance of piles and drilled shafts as discussed in different national and international building and non-building codes. A summary of extensive research on several codes are presented to facilitate the compliance with different codes.Chapter 6 discusses structural design issues of individual piles and drilled shafts such as depth of fixity.Chapter 7 discusses soil structure interaction issues related to kinematic and inertial effects due to seismic loading and available methods of analyses.Chapter 8 discusses and presents the typical procedures for the lateral load testing of piles. This guideline was developed as an aid to the practicing engineer in providing information, direction and commentary on the lateral design of deep foundations. Although all reasonable effort has been made to accurately compile the material and information contained herein, no warranty is made with regard to any such material or information and the Deep Foundation Institute assumes no responsibility for any possible errors or any direct or indirect result of the use of any such material or information. It is not intended that this document address every factor affecting lateral design for every situation. Therefore it is the responsibility of the person utilizing information from this document to confirm that it is appropriate and correct for their situation as well as to understand and properly apply

Jan 1, 2012

By F. Pinto, C. A. Prato, R. J. Rocca, P. F. J. Huerta Soaje

"The seismic hazard for civil engineering structures is generally defined in terms of deterministic or probabilistic acceleration response spectra at an equivalent rock outcropping. The design of tunnels, however, requires the definition of demands in terms of accelerations at ground surface (near the portals) and in terms of both accelerations and velocities at different depths within the alignment. The design near the portals is controlled by inertial effects and is often times impacted by the possibility of slope instability and rockfall, whereas the design at deep sections is controlled by kinematic effects. These effects are accounted for in practice by introducing deformation patterns in the structure that are related to an assumed wavefield, often times ignoring the effect of the structural stiffness in the response. This paper presents a study regarding the definition of seismic demands for different sections of 14-km long tunnel in the Andes (Argentina-Chile), with a maximum overburden of 1750 m in a seismically active region. The tunnel will pass through volcanic massifs mainly composed by andesites and rhyolites.The study includes the definition of spectrum-compatible seismograms, deconvolution, and definition of accelerations and peak particle velocities for different overburden conditions. A kinematic interaction study for a 500-m tall ventilation chimney shaft is also described, where a simple formulation for the interaction analysis is considered in order to more accurately evaluate shear and bending demands. INTRODUCTIONThe seismic design of linear underground structures, such as shafts and tunnels, generally considers the inertial forces near the shallow sectors (e.g., portals) and the kinematically imposed deformations for the deep sections (e.g., Hashash et al. 2001). The inertial forces are often times evaluated on the basis of design spectra recommended by seismic hazard studies. The kinematic demands for the deeper sections, however, needs to be defined in terms of additional information which is not always indicated by the seismic hazard studies, e.g.; peak particle velocities and accelerations, and their variation with depth. These parameters can be determined by means of a site response analysis, whereby outcrop motions can be deconvoluted in order to evaluate motions inside the ground mass (e.g., Schnabel et al., 1972). Hashash et al. (2001) defines factors that may be used in order to account for attenuation of motions inside the ground mass. However, these factors are provided for depths up to 30 m only, whereas depths of tunnels structures can range up to thousands of meters."

Jan 1, 2015

By David S. Graham, Benjamin Turner, Paul J. Axtell

Seismic challenges were at the forefront of design for two parallel replacement bridge structures over the Arkansas River as part of the I-30 Crossing Project in Little Rock, Arkansas. Although not an area of the country typically associated with high seismicity, proximity to the New Madrid Fault Zone resulted in design ground motions sufficient to trigger liquefaction in alluvial channel and point bar deposits. A detailed post-award subsurface investigation program utilized CPT with complimentary borings to obtain samples for laboratory testing to assess the continuity of potentially liquefiable layers, from which we concluded that continuous zones of liquefaction across the extent of the north approach could lead to lateral spreading towards the river. An overview of the foundation and superstructure design to resist lateral spreading forces in accordance with the latest published design guidelines and research is presented. Other seismic aspects of the design are covered including timber pile ground improvement to mitigate liquefaction at the north approach embankment and foundation input motions that differ from code-based ground surface motions due to foundation stiffness, strength, and geometry. The project showcases an example of successful collaboration between geotechnical and structural designers with contractor input to address seismic challenges in the South Central US. Furthermore, the importance of considering kinematic demands on columns and other superstructure components – not just foundations – is highlighted.

Sep 8, 2021

By Leo Panian

Over the last decade, drilled and post-grouted micropile foundations have come to be increasingly relied upon for resisting seismic loads in building foundations on the West Coast. Micropiles have been successfully deployed in a range of soil conditions, in vertical as well as battered configurations, to support a variety of structural systems difficult soils. Their high load capacity in tension as well as in compression, their ability to be installed in confined spaces with minimal overhead clearance, and their ability to be directly tested in an installation have made them indispensable for seismic strengthening of existing structures. More recently, growing industry experience along with improvements in design guidelines have led to wider acceptance of micropiles among engineers and building officials. The increasing availability of the specialized materials, coupled with growing familiarity with drilling technologies among design-build contractors has made micropiles more cost-effective and competitive. For the first time, micropiles are finding applications in the construction of new buildings, where they are combined with shallow footings in hybrid foundations to efficiently resist seismic loads. These new applications rely on more intensive engineering analyses to evaluate the performance of micropile foundation systems and develop detailed requirements for design and construction. This paper describes the design approaches and the analytical methods for the seismic design of hybrid micropile foundations, and provides examples of recent construction projects that demonstrate the application.

Jan 1, 2010

By Caroline Gerwig, Joseph R. Wickline, Zach Agioutantis

In longwall mining, the progressive caving of the roof allows stored energy to dissipate over an extended time. However, in some cases, the roof strata above the longwall panel are unusually strong and do not break with the movement of the working face. Instead, the roof material bridges over the expanse of the longwall, forming an unstable beam. Later, when this beam breaks, the stored energy can release suddenly, causing a seismic event to propagate to surrounding mine workings. The focus of this paper is to estimate the size of beams that form over longwall panels to the seismic energy recorded by the mine. Analytical calculations are used to verify two-dimensional models of longwall roof beams to determine the strain energy and gravitational energy developed, which is then released upon strata failure to surrounding mine workings. Models are developed using RS2 to model the stress, strain, and deflection along the bottom of the longwall roof beam to calculate gravitational and strain energies. Gravitational energy is shown to be the main driving factor in energy release, except for the beams with low heights. Analyses allow the determination of beam characteristics based on seismic data. The analysis is refined using swelling factor to compare various beam drop heights. The models show an increase in seismic magnitude for higher drop heights. However, the actual data provided by the Buchanan mine displays a decrease in seismic magnitude with increasing drop height, indicating that energy is dissipated into the broken gob material as drop height increases.

Jul 1, 2023