Search Documents

By C. F. Feng, L. Froyen

"In-situ processes have emerged as new and promising techniques for metal matrix composite fabrication. They offer significant technical and economic advantages over conventional processing. One of the in-situ processing routes that have been used is reactive free sintering of a mixture of powder reactants. However, materials synthesised via this route are always porous because of density differences between reactants and products. An example are the porous Al/(TiB2+Ah03) MMCs obtained by heating powder mixtures of Al+ Ti02+B with Ti02 and B in stoichiometric ratios for forming TiB2• In this study, porous Al/(TiB2+Ah03) composites were further processed by hot-pressing at temperatures above 600°C. This processing cycle was designed so that the composites could be densified. Furthermore, the reaction kinetics of the in-situ processing are studied by means of DSC analysis measured at different heating rates. The activation energies of the three intermediate steps that are involved in the reactive processing for preparing AV(TiB2+Alz03) MMCs are determined to be 923 kJ/mole, 241 kJ/mole and 235 kJ/mole respectively.XRD proved that the hot-pressed products consist of Al, TiB2 and Al203- Properties of the products are assessed by microstructural characterisation (LOM, SEM and EDS), microhardness, Young's modulus and bending tests. The results show that good microstructures, elastic properties and strengths, as well as acceptable ductilities were achieved. For the composition 79.74wt% Al-15.95wt% Ti0z-4.31wt% B, after the reactive free-sintering and hot-pressing cycles, Young's modulus is 105 GPa, bending strength is 509 MPa and maximum strain is 5.0%; for composition 88.73wt% Al-8.87wt% Ti0z-2.40wt% B, they are 89 GPa, 311 MPa and 8.2% respectively. It can be seen that the properties of products can be tailored by adjusting the relative amounts of reactants in green samples. Furthermore, for comparison reasons, Al and a binary system Al-Ti02 were identically processed as the ternary systems. Their microstructures and properties were studied."

Jan 1, 1998

By E. A. Werner, A. Pichler, A. Spalek, G. Reisner, P. Stiaszny

"Interstitial free (IF) sheet steels are used for complex shaped parts because of their excellent formability. If a deep drawn part is subjected· to a impact deformation at low temperature brittle fracture of the part may occur. This phenomenon\ is called secondary work embrittlement (SWE). One possibility to characterize this material/structural behavior is the drop-weight test. The result of .this .test is a temperature at and below which a crack can initiated in a deep drawn part under the investigated set of parameters. This paper addresses the influence of the preforming process on the sus- . . ceptibili.ty of IF steels to SWE.IntroductionInterstiiial:free (IF-) steels are frequently used in the automotive industry for complex· shaped p·arts because of their excellent deep drawability. The microstructure of the steel consists of a highly ductile ferritic matrix with embedded precipitates of nitrides and/or carbides. Brittle fracture can occur in deep drawn parts, if they are subjected to a high speed deformation at lo""w temperature. This phenomenon is called ~econdary Work gmbrittlement (SWE) [1-11]. Up to now there are no standardized testing procedures available to quantify the sensibility of IF-sheet steel to SWE. Neveitheless, a reasonable testing procedure which allows to quantify the tendency of a predeformed part to SWE is necessary for further material development. A commonly used test method is the drop-weight test performed at low temperatures. In such ·tests a cone-like drop weight expands a deep drawn cylindrical cup [l-3, 6, 8, 9, 11]. From this expansion experiment the temperature is determined at and below which a brittle crack can be initiated in the deep drawn cup under the investigated impact test parameters. The highest measured temperature at which a deep drawn cup fails by brittle fracture is called frack appearances !emperature (CAPT). The lower the value of the CAPT the lower is the sensibility of a deep drawn part of IF-sheet steel to SWE. This paper aims to clarify the role of the preforming process on the impact behavior of an IF steel. For this purpose a numerical analysis of the deep drawing process and cup expansion tests are conducted."

Jan 1, 2000

By Jan Vrestal, Josef Tomiska, Pavel Broz

"Thermodynamic investigations on fcc solid ternary Fe-Ni-Cr alloys have been performed by means of the computer-aided Knudsen cell mass spectrometry. Ternary T.AP.-series (Thermodynamically adapted power series) are used for the algebraic representation of the thermodynamic excess properties. At 1650 K the molar excess Gibbs energy GE is negative over the whole field of stable fcc phase. The molar heat of mixing HE is exothermic in the predominant part of the fcc phase field. Only between the section with a constant ratio of mole fraction Xcr/XNi = 0.64 and the fcc phase field boundary the HE values are slightly endothermic. The results of this work can be used successfully for phase diagram calculations.IntroductionThermodynamic investigations on multicomponent alloy systems such as the Fe-Ni-Cr ternary system including the three binary boundary systems are very time-wasting and usually beset with considerable experimental difficulties. Additionally, the required experimental equipment is very expansive and the obtained results are not always satistying. Therefore it is understandable that many phase diagram calculations are based only on few experimental values of the molar excess free Gibbs energy GE. Consequently, Kundrat and Elliott [1] as well as Hillert and Qiu [2] used in their reassessments of the phase diagram of the Fe-Ni-Cr system thermodynamic data mainly assumed and/or optimized by means of various reasoning.Lee [3] reported recently, a revision of the used thermodynamic description of the Fe-Ni liquid phase is necessary to obtain a better agreement with the experimental data on the bcc/liquid or fcc/liquid tie lines and liquidus temperatures in the Fe-rich region of the Fe-Ni-Cr ternary system than in the previous assessments. This is 'in full agreement with mass spectrometric investigations of Fe-Ni alloys in the liquid and in the fcc solid phase, published earlier [4,5]. Indeed, phase diagram calculations based upon the molar excess free Gibbs energies GE obtained in these studies yield liquidus and solidus lines in excellent agreement with experimental phase diagram data [5]. Nevertheless, these experimental data have not been considered later on any more, not even in the revision by Lee [3]."

Jan 1, 1996

By Motohiro Horiguchi, Kazuo Ichii, Toshio Oishi

"As a fundamental study to prepare copper-based alloys with rare earths (RE: La, Gd, Nd, Ce and Y) without any inclusions, the solubility of rare earth in liquid copper was experimentally determined. Liquid copper alloys were equilibrated with carbon and rare earth carbide in a graphite crucible in an argon atmosphere at 1523-1873 K.Solubilities of rare earth in liquid copper were determined by approaching the equilibrium values from both the lower and the ·higher concentrations than those expected· in the preliminary experiments. They were expressed as a function of temperature. Carbon in Cu-RE alloy was also analyzed and thermodynamically discussed.IntroductionOver the past several years, the demand for highly conductive and high strength copper-based alloys, such as Cu-Cr, Cu-Zr and Cu-Cr-Zr for use in electronic materials has increased.1 -7 These alloying elements are very reactive and easily oxidized to form oxide inclusions during melting. To avoid the oxide inclusions, it may be effective to utilize the strong reducing power of carbon in conditions under which no carbides form.In this study, to provide fundamental data for producing Cu-RE( rare earth) alloys without any inclusions, the solubility of rare earth in liquid copper in equilibrium with .carbon .was determined and discussed on the basis of the experimental results and the thermodynamic data.ExperimentalSample preparation for equilibrium experimentsOxygen-free copper (99.99%), lanthanum (99.9%), gadolinium (99.9%), neodymium (99.9%), cerium (99.9%) and yttrium (99.9%), and their oxides were used as starting materials.Each rare earth carbide was prepared by mixing rare earth oxide with carbon, which is a little more than the stoichiometric composition, pressing it into a tablet form and sintering at about 2000.K for 20 ks in a vacuum furnace using a graphite crucible. Powder X-ray analysis showed that only the carbon and rare earth carbide (REC2) was present in each sample.Cu-RE mother alloys (5-20 mass % RE) were prepared beforehand by mixing metallic rare earth with oxygen-free copper, and melting in an electric arc furnace."

Jan 1, 2000

By Animesh Jha, Catherine Davey

"Carbothermic reduction and nitridation reactions using synthetic kaolinite mineral were investigated for the formation of silicon based nitrogen ceramics. The temperature dependence of the reaction rate and its effect on phases formed are reported. The effect of the reactivity of carbon on the kinetics of formation of AIN and ShN4 is discussed. Using the standard Gibbs free energy values for the formation of nitrides and oxides of aluminium and silicon, a log po2 verses I/T diagram is constructed. The experimental data results are discussed and compared with the predicted phase equilibria. We also report the influence of sub-oxide gaseous species on the microstructure of the ceramic phases produced.IntroductionSynthetic kaolinite is a clay containing alumina, silica and water of crystallisation, and has a chemical formula 3(Al2O 3.2SiO2.2H2O). This mineral is relatively inexpensive and, is therefore an ideal candidate for use in the production of ceramic powder mixtures for example silicon nitride and aluminium nitride for composite material formation, When the mineral is heated, the water of crystallisation from the crystal lattice is lost via the 3(Al2O 3.2SiO2.2H2O) = 3(Al2O3.2SiO2) + 6H2O reaction. It has been shown [1·2j that on further heating to 1673K, the anhydrous kaolinite decomposes to a mixture of mulllte and silica, 3(Al2O3.2SiO2) = 3Al2O 3.2SiO2 + 4SiO2 which is consistent with the alumina-silica phase diagram, shown in figure 1.The binary alumina-silica phase diagram has a well-defined sub-eutectic immiscibility dome and this characteristic dernixing behaviour is reflected in the thermal decomposition of anhydrous kaolinite consequently the microstructural features resemble the spinodal decomposition process. It is well established that the spinodal decomposition process raises the nucleation frequency due to their low free energy barrier, (?G). The small magnitude of this barrier consequently promotes the evolution of a very fine microstructure. The process of spinodal decomposition is therefore expected to be influential during the reduction-nitridation of kaolinite minerals."

Jan 1, 1996

By Jafar Safarian, Merete Tangstad, Leiv Kolbeinsen

"Silicon and its binary alloys have several applications in metallurgical, chemical, photovoltaic and semiconductor industries. Silicon goes to its liquid state within its production, refining and when it is alloyed with other elements. Therefore, the characterization of silicon melts thermodynamics is important and useful. The liquidus and activities in several silicon binary systems have been recently calculated by the application of two liquidus constants, which were established using the experimentally determined liquidus data. In the present study, the thermodynamic properties of six silicon binary melts, which are simple eutectics, are calculated by analytical approaches. In this case, the changes in the partial and integral Gibbs free energies and enthalpies of mixing are calculated and compared with the experimental data in literature. The enthalpies are calculated by two methods and the calculation results are compared to the data from the literature. It is shown that thermodynamic properties of silicon binary melts can be accurately predicted without the use of complicated thermodynamic software.IntroductionSilicon and its alloys have several industrial applications. Silicon is used for making aluminium-silicon alloys to produce cast parts, mainly for automotive industry. Silicon in the form of ferro-silicon is used to deoxidize and alloy steel and cast iron. The photovoltaic (PV) industry has had a rapid growth in the recent years and silicon is the dominant material used for the fabrication of solar cells. Silicon is primarily produced through carbothermic reduction of quartz in electric arc furnaces and the produced metallurgical grade silicon (MG-Si) contains around 1 wt% impurities. It is further refined to produce solar grade silicon (SoG-Si) with above 99.9999 wt% Si to fulfil the chemical requirement for PV application. Since molten silicon is processed all along the metallurgical route, obtaining fundamental thermodynamics knowledge about silicon melts is valuable for the related industries."

Jan 1, 2012

By J. R. Bhamidipati, Nagy EI-Kaddah

"Over the years, mathematical modeling has been established as a viable tool for design and analysis of melting and solidification processes. Modeling of electromagnetic casting and melting systems involves three coupled problems -- determination of the containment field, the shape of the meniscus, and the temperature field -- which have to be solved simultaneously. One of the difficulties in numerical simulation of these systems is in defining and gridding the solution domain as the meniscus shape of the liquid region is not known a priori. This paper describes a methodology for solving these coupled problems in a two-dimensional electromagnetic containment field. This method is based on the solution of the electromagnetic, free surface dynamic, and heat transfer equations in a fixed domain in computational space by mapping the physical space into an invariant computational space during the search for the equilibrium shape using a variable non-orthogonal coordinate transformation. This approach, also, eliminates the need for regridding the liquid and solid regions during phase change. This methodology is demonstrated for two electromagnetic confinement systems -- the Magnetic Suspension Melting process and the electromagnetic casting of aluminum. The model predictions are in good agreement with available data for these systems. It is suggested that the methodology presented here is likely to provide a useful tool in the design, analysis, and optimization of electromagnetic confinement systems. IntroductionDuring the past decade, mathematical modeling has emerged as a viable tool for the design, analysis, and optimization of casting and melting processes /1-2/. It is generally recognized that the usefulness of modeling to study the interplay between the various process parameters without resorting to extensive experimentation relies heavily on accurate representation of the physical phenomena in these systems. In modeling electromagnetic confinement casting and melting systems, it is important that the model address all aspects of electromagnetic field interaction with the metal, if accurate predictions are to be obtained /3/. The electromagnetic field affects the heat transfer phenomena primarily through joule heating. In addition, the electromagnetic forces play a key role in heat redistribution in the molten pool via melt stirring, and, in confinement systems, support the molten metal pool."

Jan 1, 1994

By Willem P. C. Duyvesteyn

A novel hydrometallurgical process for Escondida copper concentrates has been developed by The Minerals Laboratory of BHP. The Escondida Process consists of concentrate leaching, solution purification, electrowinning and residue flotation. Part of the copper will be sold as high grade concentrate and part as high purity SX-EW copper. Contrary to previous efforts for the development of a hydrometallurgical process for copper concentrates, this patented process does not advocate the total dissolution of copper. It only aims for the copper that is readily soluble in a mildly oxidizing environment with an ammoniacal or acidic lixiviant. Both lixiviants were studied, but ammonia was preferred because of fast kinetics at ambient temperatures and pressures. By controlling the oxidation potential, the formation of sulfate ions and, consequently, of an ammonium sulfate byproduct, is precluded. These mild leaching conditions also prevent the dissolution of unwanted impurities and result in the production of ultra-high purity electrowon copper. Solution purification is carried out by solvent extraction with LIX-54. The very high loading capacity of this organic results in a compact SX circuit, consisting of two loading, one scrubbing, and one stripping stage. As the organic is selective for simple copper ions, the copper amine complex is broken down and free ammonia is regenerated and recycled for leaching. High purity copper cathodes are produced in a conventional sulfuric acid based electrowinning system. One scrubbing step is needed to separate the ammoniacal circuit from the acid circuit. Limiting copper dissolution to less than 50% also provides an opportunity to produce high grade concentrates by residue flotation. Copper recoveries in excess of 98% with precious metal values reporting to the final concentrate can readily be obtained. Complete breakdown of the copper mineral- pyrite middlings results in a final concentrate grade that can be even higher than the original feed material. The Escondida Process also provides an opportunity to accept lower grade copper concentrates producing improved copper recoveries in the mill and yet high quality concentrates for marketing. The Paul E. Queoeau International

Jan 1, 1993

By A. J. Williams, T. N. Croft, M. Cross

"The computational modelling of extrusion and forging processes is now well established. In this work a novel approach is described which utilises finite volume methods on unstructured meshes. This technique can be used to solve simultaneously for fluid flow, heat transfer and non-linear solid mechanics and their interactions. The approach involves the solution of free surface non-Newtonian fluid flow equations in an Eulerian context to track the behaviour of the workpiece and its extrusion/forging, and the solution of the solid mechanics equations in the Lagrangian context to predict the deformation/stress behaviour of the die. Some preliminary examples of this approach will be discussed.IntroductionThe computational modelling of extrusion and forging processes is now well established. Within the last 20 years the finite element method has become the most commonly used technique to simulate metal forming processes [1]-[4]. The Lagrangian and Eulerian type of formulation have been the two major approaches to this problem.Lagrangian methods are efficient and suitable for handling non-linear problems in which small strains prevail, boundary conditions do not change with the course of deformation, and where mesh distortion is not a critical factor in the analysis. Unfortunately, the above points are essential to any accurate metal forming analysis. The problems of mesh distortion and element entanglement pose a serious drawback on the use of such methods. Some automatic remeshing techniques have been developed for Lagrangian finite element analyses of metal forming problems [5]-[7]. However, these methods are not robust and efficient enough to remedy the mesh distortion problems in general. An alternative is to update the mesh manually but this is not always possible, and even when it is feasible it involves major interaction by the user. In addition, remeshing is usually applied to the whole domain which is not necessary and increases CPU time. The complexities associated with remeshing also affect the ability to parallelise the code."

Jan 1, 2001

By William Petrul

Image analysis studies were performed on mill products from laboratory flotation tests of the Zn-Pb ore from the Faro deposit in Yukon, Canada, to determine mineral liberations at specific grinds and to predict recoveries at optimum flotation conditions. The minimum and optimum grinds for liberating sphalerite and galena were predicted from size analysis data for the minerals in large ore pieces, and determined by image analysis studies of the mill products. The determined optimum grinds are about 2 Tyler mesh sizes larger than predicted because sane of the fine grained sphalerite and galena occurs in interstices between coarser grained pyrite and is liberated when the pyrite grains are broken apart. Materials balance calculations were performed on the analyzed values for the liberated and unliberated sphalerite and galenaa to determine their distributions in the mill products. The laboratory flotation tests recovered 74% of the sphalerite and 83% of the galena in Zn and Pb concentrates respectively. The mineral evaluation study indicates that the optimum recovery for sphalerite and galena are 85 and 83% respectively. The company is currently recovering 80% 'of the sphalerite and 82% of the galena.

Jan 1, 1989

By Patrick R. Taylor

Sub-micron sized boron carbide powders have been synthesized in a non-transferred arc thermal plasma reactor. Precursors for this synthesis are boric acid or boron oxide powders and methane. The powders produced were characterized in terms of size, shape and purity. Methods to increase the purity of the product were evaluated and included hot water leaching to remove unreacted oxides and controlled temperature, air roasting to remove excess carbon. Theoretical results are also presented on the thermodynamics and mechanisms of the synthesis reactions.

Jan 1, 1994

By Eoghan T. M Doyle

Oxide mixtures of nickel (NiO), cobalt (COO) and chromium (Cr203) were prepared with graphite in stoichiometric amounts and the powder mixtures were compacted to produce cylindrical pellets. The composition of chromium oxide in these mixtures were varied. Pressed pellets were reduced in a flowing stream of argon-4% hydrogen gas (500 ml/min). Both slow and rapid heating methods were adopted to raise the temperature of a pellet during reduction of oxides to form superalloy powder. The reduction temperature was varied between. 1523 and 1623K. The effect of heating rate and niobium oxide addition on the microstructure of the superalloy produced was studied by using ordinary light and scanning electron microscopes. New phases formed as a result of reduction were identified by X-ray powder diffraction technique. The mechanism of reduction of oxides together with the microstructure of NiCrCo alloy are discussed. The thermodynamics of formation of ternary alloy phase is elucidated on the basis of binary phase equilibria and Gibbs free energy of mixing data for the constituent alloy compositions.

Jan 1, 1992

By Qinmeng Wang

The oxygen bottom blown copper smelting process is a new technology which has been widely applied to the copper production in China. In this work, a computational thermodynamics model for this technology has been established, based on smelting mechanism and theory of Gibbs free energy minimization. The calculated results from the model agree well with the actual industrial data, indicating that the model can be used for the predictions under different operating conditions. The tendencies of the key parameters (such as Cu losses and Fe3O4 content in slag) and the distribution ratios of the minor elements (such as Pb, Zn, As, Sb and Bi) can be predicted by adjusting the oxygen/ore ratio charged into the bottom blown copper smelting furnace. The model can be used to monitor and optimize the industrial operations of the oxygen bottom blown copper smelting process.

By D. C. Lynch

While a sizable amount of data exist as to the activity and distribution of minor elements between matte and metal, there has been no unifying theory presented delineating the form of dissolution of these elements in molten sulfides. In order to alleviate that deficiency the literature concerning the behavior of As, Sb, Bi and Pb in mattes is reviewed. Models present in the literature, regarding the thermochemical behavior of minor elements, are tested, and new models are presented and evaluated using thermodynamic theory. The results of those analyses are used to predict optimum conditions for the volatilization of minor elements. The dearth of data on the behavior of minor elements in nickel mattes requires that this review focus on copper- iron mattes. An effort is made, however, to utilize basic knowledge regarding nickel sulfides and the interaction of nickel with the minor elements to predict the behavior of those elements in nickel-copper and nickel-iron mattes.

Jan 1, 1993

Several processes are now available for the recovery of free and WAD cyanide from gold plant solutions and pulps. In the past, the incentive for evaluating cyanide recovery in gold plant flowsheets has been economic. In many cases, it has been possible to demonstrate (at least in the laboratory and on paper), an improvement in process economics by; (i) reducing the costs of tailings detoxification, (ii) recycling cyanide at lower cost than the purchase/delivery price of new cyanide, and (iii) generating additional revenue via by¬product sales. Despite these convincing arguments, few cyanide recovery plants have been built at operating gold mines. Also, there is arguably an even more compelling reason for mining companies to consider cyanide recycling. With the growing storm of negative public opinion that the use of cyanide in the mining industry is attracting - following several highly publicized spills over the last couple of years - the time has come for the gold industry to demonstrate environmental diligence and stewardship in the use of this commodity that is so vital for their industry. There is no doubt that the widespread implementation of cyanide recycling will reduce the impact of the cyanidation process on the environment, both by reducing the risk of spills (with less cyanide being transported from manufacturing plants to gold mines), and by reducing the loading of toxic and non-toxic metals and ions in the tailings. In this paper, the various processes that are available for cyanide recovery are discussed, along with the process chemistry. Results of several laboratory and pilot plant trials that have been conducted over the last few years are also presented.

Jan 1, 1998

By R. T. Seaman

Pressure oxidative treatment of whole ores and/or mineral concentrates is used to leach or liberate metals of value for downstream recovery. Silver, when present, is often lost in processing, precipitating as a cyanide-insoluble jarosite in the residue. Depending on pressure oxidation conditions, the degree of silver loss to jarosite can vary dramatically. Batch bench-scale testwork is often performed to define that loss, and then assess the implications in continuous operations. This paper focusses specifically on the impact of CESL pressure oxidation conditions on silver recovery, and discusses limitations of batch bench-scale testing as well as means of overcoming these limitations to better predict silver recovery in the scale up from bench-scale to continuous operations. Since silver is only partially soluble in both sulphate and chloride media, it will gradually leach and deport to a jarosite as oxidation progresses. When a silver-insoluble anion, for example iodide, is dosed prior to oxidation, there is a marked improvement in silver recovery from batchgenerated residue; however, that benefit is not consistently seen in continuous operations. The difference has been attributed to the dynamic solution conditions in the batch test, specifically the first few moments of oxidation. Using these principles, a predictive correlation has been established between initial leach concentrations of iron and acid and ultimate silver recovery with iodide addition.

By E. C. T. Chao

Micro-optical and synchrotron radiation-induced X-ray fluorescence (SXRF) techniques have been used to study unoxidized and oxidized samples of Carlintype sedimentar,y rock-hosted disseminated gold ore. In these samples, Where much of the gold is submicroscopic, the SXRF technique, which has a spatial resolution of about 20 ~m and a minimum detection limit (MDL) in the ppm range, is an ideal and necessary tool for precisely locating gold-rich areas in a sample. Gold-rich areas pinpointed by SXRF were later studied in detail by micro-optical methods, principally optical microscopy and scanning electron microscopy with energy-dispersive X-ray analysis (SEM-EDX). In two unoxidized and one oxidized ore samples, SXRF analyses have shown gold to be present predominantly in discrete clay-rich and silicified areas. Gold was not detected by SXRF in association with pyrite or carbonaceous materials. SEM-EDX examination of the gold-bearing areas in the unoxidized samples succeeded in identifying only two free gold particles, 0.2 and 0.5 ~m in size. In the oxidized sample, gold particles appear to be larger (but still submicroscopic) in average size and more evident in micro-optical examination after SXRF location of goldbearing areas. The findings of these studies may help to improve the efficiency of processing and recovery of gold from unoxidized ores.

Jan 1, 1987

By J. R. Odekirk

The nature of mineral distributions and locking characteristics in mill products are important factors in understanding mill performance. Such data are obtained by microscopic point counting methods. Reduction 'of point-count data from volume to weight percentages, and reduction of data for each size fraction back to a head sample requires lengthy hand calculations. The use of computer processing for such data reduction results in obtaining information on a realistic time basis. An example of computer processed point-count data is presented.

Jan 1, 1981

By David R. Brosnahan

Increased Cu grades due to chalcopyrite-rich ore from The Doe Run Company's new Casteel Mine prompted a program to increase Cu recovery. Preliminary tests indicated that prohibitive quantities of FeS2 float with chalcopyrite. Point counting of mill stream samples showed that locking was not a major problem, although grinding to finer particle size enhanced the floatability of both chalcopyrite and marcasite. Backscattered electron images and microprobe analyses of FeSz minerals revealed the presence of Pb which appears to occur as solid solution in marcasite, and as a sub-micron particulate Pb phase in pyrite.

Jan 1, 1987

By R. D. Irwin, W. M. Mullins, E. A. Medina

"Various stability criteria are introduced and thermo-kinetic models for metallurgical processes are used as concrete examples for evaluation. Kinetic criteria for the process of dynamic recrystallization are proposed. These criteria are compared to the non-equilibrium thermodynamic approaches discussed in the literature. The application of macroscopic stability criteria to materials processing is then discussed.IntroductionThe mechanical behavior of metals at elevated temperature is very well predicted by any of several empirical constitutive relations. Typical is the power-law (or Swift's) form,Equationwhere r-is the stress, y is the strain and m, n , t0, y0 and Q are material constants. This form has been used with some success in the metals processing area [1]. In general, though, all of the empirical constitutive equations are static, failing to account for any dynamical properties of the system they seek to describe.The physics of warm deformation is qualitatively well understood. An example is power-law creep, where the dominant mechanism is assumed to be lattice diffusion limited climb of dislocations, which allows the strain-rate to be determined by the applied stress through"

Jan 1, 1997