Search Documents

By H. J. Garcia

Biodegradation of cyanide by microorganisms isolated from solids previously exposed to cyanide has been investigated. Initial sodium cyanide concentration was 300 ppm at pH 10.5. The kinetics of biodegradation were found to be first order with respect to cyanide concentration, and the overall reaction rate constant is k = 0.102 day-1. The activation energy and the frequency factor were determined to be { A }Ea = 5.45 Kcal/mol and A = 1.28 x 10-2 sec-1, respectively. Based on these values, thermodynamic properties of an intermediate activated complex were assessed. All tests resulted in cyanide concentrations less than 0.1 ppm in about 35 days at 250C, whereas at 350C the time of biodegradation to reach this cyanide level was 30 days. Kinetic data were also established to relate biodegradation to amount of inoculum. The maximum theoretically-attainable rate, Vm , and the optimum amount of inoculum, K , were determined to be 4.8 x 10-4 M NaCN/day and 7.5 % of amount of inoculum. With respect to the mechanism of biodegradation, cyanide was shown to decompose to carbonate, bicarbonate and ammonia. Titrimetric analyses revealed concentrations of 5.6 x 10-3, 4.8 x 10-3 M, and 70.2 ppm for carbonate, bicarbonate and ammonia, respectively. The average cell population was determined to be 3.75 x 108 cells/mL.

Jan 1, 1994

By J. E. Wey

Extraction of cobalt from cobalt sulfide and cobaltite flotation concentrate from the Blackbird Mine, Idaho, was investigated using an adapted strain of Thiobacillus ferrooxidans. Cobalt extractions as high as 100% were realized in the inoculated experiments, whereas only 4% extraction was obtained in the sterile run. The influence of pulp density on the rate and extent of cobalt extraction was also determined. It was found that the extraction of cobalt followed predominantly the indirect mode of bacterial activity. In this process, ferric iron oxidizes cobaltite to cobalt sulfate and ferric arsenate while being reduced to its ferrous state; the bacteria continuously re-oxidize ferrous to ferric iron. Electrochemical measurements using cyclic voltammetry suggested that cobaltite oxidation involved a number of intermediate reactions.

Jan 1, 1993

By H. Kamiya, H. Hasegawa, M. Nojiri, S. Matsui, Y. Fukuda, M. Tsukada

"The present paper focuses on the action mechanism of anionic polymer dispersants in dense Si3N4 and SiC suspension. An atomic force microscope (AFM) was used to determine the relationship between the macroscopic suspension viscosity and the microscopic adsorbed structure of a polymer dispersant at the solid / liquid interface. The surface interactions within the suspensions were analyzed in various dispersant pH and additive conditions. The addition of an anionic polymer dispersant decreased Si3N4 and SiC suspension viscosity and increased electro-steric repulsion force on the non-oxide surface in solution at pH> 6 which was the isoelectric point of the materials. It was assumed that the increase of repulsive force was promoted by a hydrophobic adsorption of polymer dispersant on the non-oxide particles.IntroductionThe surface of silicon nitride and silicon carbide powders in a water suspension system has quite a complex molecular structure. In the case of Si3N4, hydroxyl and ammonium groups form on the surface and the pH of the suspension is increased from neutral to about 10 due to surface oxidation. The particle surface is negatively charged in alkaline solutions (pH=10), because the isoelectric point of silicon nitride exists in the pH range from 5 to 6. However, in spite of charging the negative surface charge, an anionic polymeric dispersant is generally used for the reduction in slurry viscosity.In dense SiC suspensions, an anionic polymer dispersant is generally used in order to disperse aggregates and reduce the suspension viscosity, too. Since an anionic dispersant is used in alkaline solutions higher than the isoelectric point of silicon carbide, the dispersant adsorbed on the negative charged surfaces of SiC.Few researchers have discussed and estimated the adsorption mechanism and structure of anionic polymeric dispersants on silicon nitride and silicon carbide surfaces. This is because it is difficult to observe the structure and measure the interaction at the solid/liquid interfuce directly. However, new developments in surface-force measurement technology have enabled the determination of non-DLVO type interaction for analyzing aggregation behavior2. The use of the AFM for analyzing the effects of various surfactants and co-polymers on colloidal dispersions and solid surfaces has also begun to rapidly expand to characterize the interaction between solid surfaces."

Jan 1, 2000

By Guo Xian Jian

In this paper, the gas composition calculations on the FeS-H20 system at elevated temperature were performed. The results show that the gas constituents are H20, S02, H2S, Sj, H2, and O2 and the order of the compositions partial pressure is PH2o> PH2 >PSO2 >PSj >PH2S >PO2 when FeS is oxidized into Fe304 and FeO by steam in the temperature of 700°C -960°C, the Claus process occurs with the decrease of gas temperature in the off-gas and the S02 and H2S in the gas are transformed into Sj , the critical temperature for the transformation is 600°C, and conversion percent of Sj is 97% at 330°C,

Jan 1, 1996

By Tingyao Liu, Lihui Han, Qing Liu, Bao Wang, Teng Yang, Yong Sheng

This paper mainly investigates the mass transfer phenomena of rare-earth concentrate from leaching process in Rushton stirred tank reactor with rotate speed of 100-600 rpm. In the research, a certain amount of sphere particles with 50-450 μm in diameter is treated as the mineral particles. Comparison of laboratory experiment data with numerical simulation is performed. The results show that the critical impeller speed for complete dispersion is 300 rpm. And the maximum value of turbulence kinetic energy appeared 15 mm away from paddle, where the mixing time is decreased 55% and 80%, respectively, when mineral particles are injected into stirred tank through one or four filling ports. Moreover, with mixing process going on, the numbers of particles near the paddle region accounts for as much as 58% of the total amount. Meanwhile, following the particle diameter increasing, the particle concentration of the upper part of stirred tank reactor is increased.

Jan 1, 2015

By Jean P. Murray

The extractive metallurgical industry is a major consumer of high-temperature process heat. It is, consequently, a major contributor of C02 emissions and other greenhouse gases derived from the combustion of fossil fuels for heat and electricity generation, or from the process itself. These emissions can be substantially reduced by replacing fossil fuels with solar energy as the source of process heat. Concentrated solar radiation can supply a large amount of thermal energy to endothermic reactions at temperatures exceeding 2000 K. Another potential for C02 emission reduction exists as well. Thermodynamically, the total amount of energy required for metal production at any given temperature is the enthalpy change of the reaction, AH. Of this total, an amount equal to the Gibbs free energy AG must be supplied as high quality energy in the form of electrical work or by using a reducing agent. Many conventional metallurgical electrolytic processes and reducing furnaces are unable to add only the thermodynamically required electricaVchemical energy due to process inefficiencies. Electrical work in excess of AG for the reaction may be used to supply process heat, or excess chemical reducing agent burned to supply process heat. Besides the thermodynamic and economic drawback, this inefficiency results in excess C02 emissions derived from the combustion of fossil fuels. With these practices, energy becomes an important cost element of the metal produced. Highly-concentrated solar energy has the demonstrated potential to separate these two forms of process energies, allowing the addition of only the thermodynamically required high-quality energy while high-temperature solar process heat is provided to the reactor. Examples of metal oxide reduction processes that have been studied experimentally in solar furnaces include the production of Fe, Al, AI/Si alloy, Mg, Zn, Tic, Sic, CaC2, TIN, Si3N4, and AIN by carbothermic reduction of their oxides, and the high-temperature solar- electrothermal reduction of ZnO.

Jan 1, 1999

By Lin Li, Wen Shi, Hua Wang

"Specimens of the ultra-low carbon bake hardening steel were soaked for 1 min to 5 min, and then cooled by water quenching. The internal friction experiments were carried out to detect the spectra of the specimens. Results show that Snoek peaks are present in all the specimens, however, an obvious Snoek-Koster peak is found only in the 5 min-annealed specimen. Besides, tensile results indicate that the bake hardening values increase with the annealing time prolonging from 1 min to 3 min, but decrease as the annealing time prolongs further to 5 min. The solute distributions in the specimens were characterized by three dimensional atom probe. Some segregated C and V are found in the 1 min-annealed specimen, and the C and V contents decrease as annealing time prolongs to 5 min.1. IntroductionAs an excellent member of automotive body panel materials, various types of bake hardening (BH) steels have been developed since 1980s. Bake hardening property, as one of the most important mechanical properties, has been studied by many researchers [ 1-5]. As is known, BH phenomenon is generally controlled by the interaction between solute C and dislocations. The Snoek peak of internal friction (IF) is very popular in the investigation of solute C [6-9]. However, result of internal friction cannot suggest the distribution pattern of solute C as well as its influence on BH phenomenon.Three dimensional atom probe (3DAP) can diagnose solute element atoms as well as nano-sized precipitates, and it is the only instrument that currently can identify the identities of individual atoms in a material and measure their spatial coordinates with the resolution close to 0.3 nm [10]. There have been a number of studies about using 3DAP to detect solute elements as well as nanometer sized precipitates [11-19]. For example, Hono et al. [16] used 3DAP to determine the solute elements in an age-hardened Mg-Ca-Zn alloy, and they also obtained the distribution patterns of the observed elements."

Jan 1, 2011

By Brandon R. Ball

An investigation of the effects of ozone and ozone-induced hydroxyl radical on reducing whole effluent toxicity is described and discussed relative to the application of ozone for industrial water treatment. Results from operation of an ozone system treating industrial effluent from a lead and zinc mine in Colorado are presented. The mine discharges 1,000 gpm of wastewater into a tributary of the Arkansas River and has historically exceeded Whole Effluent Toxicity (WET) limits and on occasion has exceeded numeric limits for copper, ammonia, and cyanide. Based on results of a Toxicity Identification Evaluation (TIE) conducted on the effluent and individual process waste streams, the source of effluent toxicity is believed to be primarily associated with organic reagents used in the milling process. Based on test results, an applied ozone to COD ratio of 3: 1 by weight and a contact time of 30 minutes was found to be effective for reducing whole effluent toxicity at pH 11 but not at pH 7, indicating oxidation by hydroxyl radical to be the dominant mechanism responsible for toxic-ity reduction. At an applied ozone to COD ratio of 3:1 and a pH of 11, toxicity was improved from 0 percent survival to 100 percent survival for Ceriodaphnia dubia and fathead minnow (Pimephales promelas) based

Jan 1, 1996

By Farhang Hedjazi

Anglo Asian Mining have recently installed an industrial-scale UF/RO plant to treat process liquors from the integrated heap leach/agitation leach/ resin-in-pulp gold ore treatment facilities at their Gedabek gold-copper mine in Azerbaijan. The UF/RO plant is designed to treat 60 m3/h of leach solution to produce discharge quality water. The RO concentrate, which contains elevated concentrations of copper, silver and cyanide, is sent to the company’s SART plant for the recovery of the metal values as a precipitated sulphide concentrate and the cyanide, which is recycled to leaching. The new water treatment plant improves the sustainability of the operations at Gedabek by enabling replacement of fresh water input with RO permeate and safe discharge of permeate to the environment, during periods of excess water balance. The paper includes pilot plant data and early results from the full-scale plant.

By John Dasher

One of our War Plants processed Bolivian concentrates as low as 17% Sn by the Arnhem process (pressure leach with HCL) and sent the waste acid down a ditch to Galveston Bay where the chlorides, mostly iron, hydrolyzed. Oyster men, and Texas, demandedimpoundment until a disposal process could be developed. A recycle process found by lab work was recommended, piloted and a plant built. This involved cementation of As Sb, Cu, Bi and Ag on light moving scrap iron and of Sn & Pb on Al turnings (then not recyclable), evaporation and crystallization of hydrous FeCl2, roasting crystals in a muffle furnace and absorbing HCI for reuse. The residue from leaching the low grade concentrates was floated to remove undissolved sulfides, classified and passed over sand and slimes tables to get a smeltable concentrate, a discardable sand tail and a slimes tail worth treating After desliming at 2 micro meters cassiterite, oxide flotation gave good, lab results; but commercial equipment wasn't adequate then. Chloride volatilization, with or without smelting gave high recoveries of Sn as SnCl2, whose marketing was questionable. I have heard this was finally fluxed and smelted.

Jan 1, 1992

By G. B. Harris

Jaguar Nickel Inc. is developing the Sechol Nickel-Cobalt Laterite Project in Guatemala, Central America. Recognizing the potential advantages offered by chloride brine chemistry, Jaguar, at the facilities of Process Research ORTECH Inc, Mississauga, has developed an Atmospheric Chloride Leaching Process using a mixed chloride lixiviant to recover the nickel and cobalt, whilst leaving the majority of the iron and magnesium in the leach residue. Subsequent solution purification and mixed nickel/cobalt hydroxide product recovery is by standard precipitation methods, using recycled caustic magnesia, with a final stage of pyrohydrolysis of a portion of the concentrated magnesium chloride brine for recycling both the caustic magnesia and chloride lixiviant. The flowsheet that has been developed also offers opportunities for by-product recovery and efficient, environmentally clean process effluent management. The paper discusses some of the early leaching results in the context of strong chloride brine chemistry, with emphasis on how the controlling of water activity, hydrogen ion activity and chloride concentration permits the selective leaching of nickel and cobalt from an iron-magnesium matrix. Keywords: nickel, cobalt, iron, magnesium, Sechol, Guatemala, chloride, pyrohydrolysis

Jan 1, 2004

By Li. Jiarong, Zuojian Liang, Qingyan Xu, Baicheng Liu, Shizhong Liu, Hailong Yuan

Single crystal solidification of turbine blades is a key technology for the production of reliable and high efficiency gas turbines. The solidification process of single crystal investment castings causes a number of problems that have to be solved such as the increase of casting defects and complexity of production process. Computer modeling and simulation is helpful to predict the defects and improve the process design. In the paper, a mathematical model for three dimensional simulation of solidification and single crystal growth of investment castings was developed based on CA, mechanism of crystal growth and basic transfer equations such as heat, mass transfer equations. Many factors including constitutional undercooling, curvature undercooling and anisotropy, which had vital influences on microstructure evolution, were considered in the model. Temperature, crystal growth interface and structure defects of investment castings of single crystal superalloy were investigated at withdrawal rates of 4.5mm/min and 7mm/min. Simulated results showed that microstructure evolution and structure defects were predicted reasonably and calculated results were coincident with experimental ones. The study indicated that three dimensional solidification simulation technique is a powerful tool for understanding the fundamental of solidification and the formation of structure defects in single crystal investment castings and finally for optimizing process design.

Jan 1, 2004

By Merete Tangstad, Fei Li

This paper studies the quartz and carbon black pellets at elevated temperature with varying temperature and gas atmosphere. High-purity quartz and commercial ultra-pure carbon black was mixed (carbon content wt.15%), and then pelletized into particles of 1-3mm in diameter. The stoichiometric analysis of the pellet during heating is studied in thermogravimetric analysis (TGA) furnace at different temperature in CO and Ar atmosphere. The microstructure, phase changes and element content of sample before/after heating is characterized by X-ray diffraction, scanning electron microscope, X-ray fluorescence and LECO analyzer. The reaction process can be divided into two stages. Higher temperature and argon atmosphere are the positive parameters for SiC formation.

Jan 1, 2016

By Jianxun Song, Hongmin Zhu, Qiuyu Wang, Jungang Hou, Shuqiang Jiao, Xiaobo Zhu

This work presents the results of a study on the Ti3+/Ti2+ couple redox potentials vs. Cl–/Cl2 at the temperature range (673 to 1073 K) in fused LiCl-KCl eutectic by direct potentiometric method. Initial concentrations of TiClx in solvents did not exceed 5.0 mol%. Basic thermodynamic properties of the reactions TiCl2+1/2Cl2(g)=TiCl3 were calculated using the temperature dependencies of apparent standard potentials of the couples E* Ti3+ /Ti2+.

Jan 1, 2014

By Animesh Jha

Univariant diagrams are constructed for the reduction of nickel and cobalt oxide and sulphide minerals. The results from the carbothermic and hydrogen reduction of sulphide minerals are compared. The importance role of lime and calcium sulphate in controlling the emission of sulphurous- gases during reduction reaction is also explained. The mechanism of carbothermic reduction of nickel sulphide is explained by examining the sulphur exchange and reduction reactions. The phase equilibrium relationships that determine the formation of multicomponent liquid are characterised. Also the governing equilibria for inert atmosphere calcination- roasting of nickel and cobalt sulphide minerals are also described for the metallization of nickel and cobalt.

Jan 1, 1993

By Sylwia Zymankowska-Kumon, Rafal Danko, Mariusz Holtzer, Artur Bobrowski, Michal Kubecki

"Moulding sands with furan resin constitute constantly growing part in technologies of producing castings from iron alloys. Due to the presence of harmful substances in resins such as furfuryl alcohol, phenol and formaldehyde, using those mould sands may be hazardous to the natural environment and workers. The general assessment of harmfulness of sands used for molds and cores encompasses 2 basic points: emission of hazardous substances during processes of preparing sands, pouring mold with liquid metals (high temperatures), cooling and shaking-out; possibility of washing out hazardous substances from used sands to the environment, during storage or economic use outside foundries. We present the results of research on the assessment of harmfulness of mould sands with furan resin in the scope of the above points. The research was conducted according to the original method prepared by the authors, which has been used for years in cooperation with various foundries (Poland, abroad).IntroductionSands are used by the foundry industry to create metalcasting moulds, where the individual sand grains are typically bound using bentonite clay and carbonaceous additives or resins. During the casting process, the moulds can be exposed to temperatures as high as 1500°C depending upon the metal being poured. The molten metal causes thermal decomposition of carbonaceous additives or resins, which results in the formation of potentially hazardous organics that are emitted to the atmosphere and condense in the moulding sand [1]. The moulding sands are reclaimed within the foundry, but part of them are eventually discarded in landfills, because it is not longer suitable to make metalcasting molds [2, 3]."

Jan 1, 2013

By Liang Li

Thermodynamic analysis and experiments were conducted in order to verify the feasibility of preparing crude titanium tetrachloride (TiCl4) via the carbochlorination of low-grade titanium slag in molten salt. Titanium slag, assaying 74.6 wt% TiO2 with high calcium and magnesium oxide impurities, was treated by an optimized carbochlorination process in NaCl molten salt. These impurities in the titanium slag were chloridized simultaneously, and chlorination products FeCl2, MnCl2, MgCl2, CaCl2 and CrCl3 were collected in the furnace slag. XRD and SEM/ EDS analysis of residue shown that SiO2 and Al2O3 in titanium slag were difficult to chlorinate completely. Theoretical calculations and industrial-scale experimental studies reveal the content of TiCl4 in the products was more than 98.8 wt% and thus proved the feasibility of utilizing low-grade titanium slag for TiCl4 preparation by molten salt chlorination technology.

By Animesh Jha

The carbothermic reduction of chalcopyrite has been studied in the temperature range 1073 to 1273K in presence of lime. The role of lime during the reduction process is explained and the phase equilibria leading to the metallisation of copper and iron are discussed. The effect of coal and carbon monoxide on the reduction process have been studied and the rate governing steps are identified. This investigation also cites examples of possible mechanisms of physical separation of metallic Cu from iron during the reduction process.

Jan 1, 1992

By D. Lambert

Process modeling for large deformation metal forming processes has been developed into a very successful tool in commercial applications during the last two decades. DEFOR.MTM is a well-known metal forming process simulation program used by many industrial and research institutions. Recent developments include the ability to model multiple deforming body behavior during multi-pass pack rolling and microstructure prediction during multi-pass shape rolling. This paper summarizes how DEFOR.MTM can be applied to a number of rolling processes and briefly describes preliminary work carried out using the ALE technique. Keywords: Simulation, Rolling, Pack, Shape, Microstructure, FEM, ALE, Tantalum

Jan 1, 2003

By Uday B. Pal

In the electrochemical vapor deposition (EVD) process, gaseous cation precursors are passed over one side of a porous substrate, and oxygen is passed on the other side of the substrate. The gases diffuse and react within the porous substrate, and the pores get filled with the desired solid oxide. Subsequent solid state electrochemical transport through the solid oxide in the pores continues the reaction, and the film grows over the porous substrate. The EVD process has been used to deposit lanthanum chromite interconnection films and yttria stabilized zirconia electrolyte films over porous air electrodes. The EVD growth of these solid oxide films is found to be parabolic in nature, which indicates that the solid state transport (diffusion) of ions through the film controls the growth. This solid state transport can be analyzed using Wagner's treatment of the electrochemical transport. Conductivity measurements and the information on the defect structure of the oxide can be combined with the EVD growth rate measurements to calculate the solid state transport properties (transport numbers and partial conductivities) of the rate-controlling minority species in the oxide. Using this approach, the EVD growth of other electronic, mixed conducting and ionic solid oxide films can also be analyzed.

Jan 1, 1992