Search Documents

By Paul Taurasi, Mahmood Khwaja, Anjuli Corcovelos, William Brick

California’s San Diego County Water Authority provides a safe and reliable water supply to more than 3.3 million residents through twenty-four member agencies. The 2nd Aqueduct pipelines, a critical infrastructure consisting of three large-diameter pipelines, are susceptible to natural threats including streambed erosion, channel migration, and seismic hazards within the 3,840-foot-long Moosa Canyon segment of the alignment. A state-of-good repair, hazard mitigation, and resiliency project is progressing to ensure uninterrupted water supply. For each pipeline, a segment will be replaced by tunneling. A high-level project development approach is presented, focusing on alternative selection, environmental and geotechnical considerations, and operations and maintenance constraints.

Jun 13, 2023

By Irene Bendanillo, Canon Cheung, Justin Lianides, Derek Penrice

The SLAC National Accelerator Laboratory’s two-mile-long particle accelerator generates the world’s brightest X-rays from its Linac Coherent Light Source (LCLS) freeelectron laser. This facility has driven groundbreaking discoveries in medicine and industry. The LCLS-II-HE project will provide a significant increase in laser energy, allowing cutting-edge research in fields including biology and environmental science. A key project component is the Low Emittance Injector Tunnel (LEIT), a 240-foot-long tunnel to be built alongside the existing accelerator and connected to it via a 30-footlong Transfer Tunnel. This paper discusses site and scientific constraints that led to the selection of the LEIT configuration: tunnels to be constructed using the sequential excavation method in mixed-face conditions comprising native rock and placed backfill, and critical design considerations including protection of overlying and adjacent historic structures and structural accommodation of near-fault seismic loading.

Jun 13, 2023

By Xiyu Gao, Yi Yang, Mark I. Pownceby, Shuiping Zhong, Miao Chen

In the present study, X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray absorption near edge structure (XANES) spectroscopy, and Raman spectroscopy were used to investigate the effect of chloride ions on chalcopyrite bioleaching and chemical leaching at 25 °C. The leaching results show that the addition of chloride ions suppressed the dissolution of chalcopyrite in both chemical and bacterial leaching. In chemical leaching, the solution redox potential in the experiment without Cl− stayed in a range more suitable for chalcopyrite dissolution compared with experiments with Cl− . In bioleaching, the bacteria activity was suppressed by Cl− leading to low dissolution rates of Cu. Surface morphology and chemical speciation studies confirmed the formation of potassium jarosite on the surface of the chalcopyrite leach residues. In addition, S K-edge XANES indicated the formation of trace amount of elemental sulfur and covellite on the mineral surfaces.

By Lourens Scheepers

Mining induced seismicity and rockbursts have been part of the deep level gold mining industry in South Africa for many years. One could be forgiven for thinking that we should know everything there is to know by now to have rockbursting under control to a level that it has minimal impact on safety and production. Well, we don’t… There are things we know that we know, and they are implemented, or should be. There are thigs we know that we don’t know, and they are researched, or should be. There are things we don’t know that we don’t know, and, well, we don’t know… We know that seismicity and the associated potential for rockbursts generally increase with an increase in stress (increase in mining depth and/or mining span and creation of remnants) and proximity to faults and dykes. We know there are a number of potential sources of events in a mine; that is: mining abutments, pillar abutments, mining faces and geological structures (faults and dykes). We know there are a number of event mechanisms associated with these sources; that is: slip on a geological structure, shear through intact rock and bursting of the rock near the edge of a mining excavation. One of the tools used more and more and with increased success to identify event source mechanisms is Moment-Tensor analysis (MT). This typically assist in differentiating between three event mechanism components: volumetric deformation component, axial deformation component and slip / shear component. The insight gained from MT assist greatly in identifying the most likely event source to assist in understanding the rockmass response to mining. We know that the seismic response in our mines are mining induced (not natural). This may seem trivial, but it is important to realise that we influence the seismic response with the way we mine, and by how much we mine (extraction ratio). Therefore we put design rules and strategies in place to reduce the seismic hazard and we install rockburst support in our mining excavations. We know the seismic response to mining is influenced by the properties of the rockmass, including strength, stiffness and brittleness, but quantifying its influence is typically more difficult than expected. We know numerical modelling can improve the engineer’s understanding of the potential rockmass response associated with designed mining layouts and strategies. For our environment (narrow, tabular large area) elastic boundary element modelling remains the most convenient and practical approach, but it overestimates the stress at mining abutments and underestimates the stress further away from these abutments. Adding a crushing (based in limit equilibrium) modelling approach vastly improves the boundary element modelling ability to simulate the deformed (interpret fractured) zones and associated redistribution of stress. We don’t know how to quantify what an acceptable seismic risk is. We don’t know if we can mine remnants at an acceptable seismic risk. Some remnants are extracted surprisingly easy, others serve us with devastating rockbursts. The limit equilibrium modelling shows potential to significantly improve our ability to quantify the rockburst risk. We don’t know if large-scale preconditioning is possible and will be effective to significantly reduce the seismic risk associated with remnant and pillar mining. Research is required (and has been initiated). Vast areas of ground have been extracted historically in the South African gold fields. Most gold reserves are now in deeper ground (4000 m) and historic remnants (areas left before due to mining difficulties) as well as pillars (regional stability pillars). If we cannot find ways to extract these reserves at acceptable risk levels, the future of the South African gold mining industry is very short.

Apr 26, 2022

By M. De Ladurantaye-Noël, M. Laliberte

Selenium is widely present in the environment at usually low concentration. It is mostly present in the environment at higher oxidation states, i.e., as selenites and selenates (+4 and +6 oxidation states respectively). It is rarely present as selenides (-2 oxidation state) and almost never found as the element (0 oxidation state). Selenites and selenates are generally soluble in water, as such they cannot easily be removed from water by precipitation. Selenites can form insoluble surface complexes with metal oxides such as ferric hydrous oxide and manganese hydroxide, and can therefore be removed that way. However, it is not so common to find selenites in natural environments as it will quickly oxidize to selenate in aerobic conditions. Elemental selenium can also be produced from selenites or selenates by using a reduction process; the end product is a colloid that can be destabilized to be removed from water using the right chemistry. Because of their toxicity, selenides need to be handled with care, and if present, it can form insoluble metal salts or, at low pH, be emitted as H2Se, a noxious and highly toxic gas. The most favorable selenium forms for its removal are therefore selenite and elemental selenium. Organo-selenium species play a crucial part in understanding selenium toxicity. There are a great number of these species. Basically, any organic species that contains sulfur has an equivalent that contains selenium. Of particular interest is the substitution of sulfur by selenium in the two sulfur-bearing amino acids, cysteine and methionine, resulting in selenocysteine and selenomethionine. Methylseleninic acid (CH3SeO2H) is another organo-selenium specie which has been detected in water treated by biological processes and which is biologically active.

Feb 1, 2023

By N. Sloan Dworian, Alyssa Smith, Ian Kellogg

Many studies have utilized magnetic susceptibility data to fingerprint porphyry copper centers; however, usage of magnetic susceptibility data to identify trends in a Climaxtype molybdenum porphyry deposit is limited. To better understand potential petrophysical signatures in a Climaxtype Mo porphyry deposit, magnetic susceptibility data was gathered at regular intervals from core holes across the Climax Mine, targeting major lithologies and styles of alteration. Preliminary analysis suggests that there are quantifiable patterns which may correspond with the mineralizing intrusions. This data can complement current mapping and exploration techniques to identify Climax-type molybdenum porphyry centers and likewise further the exploration potential for this deposit type.

Feb 22, 2026

By K. Louk, E. Gilliland, N. Ripepi, M. Karmis

"Carbon dioxide (CO2) injection in deep unmineable coal seams can enhance coalbed methane (CBM) recovery as well as effectively and permanently store the CO2. Enhanced coalbed methane (ECBM) recovery and CO2 storage capacity can be improved by altering injection parameters including the injection well locations, number of injection wells, and the time and rate of the injection. A sensitivity study was performed with sixteen different injection scenarios on a coalbed methane field in Buchanan County, Virginia to understand the influence of the injection parameters on methane production, CO2 storage and the extent of the CO2 plume. History matching was done for the gas and water production period prior to injection based on field data from an active US Department of Energy funded pilot project. INTRODUCTION The coal structure is a combination of the coal matrix and cleats. In a CBM reservoir, the methane (CH4) is stored in the matrix under adsorption properties, not as a free gas. During CH4 production, the reservoir pressure is reduced and gas is released from the surface of the coal, diffuses through the matrix and transmits to fractures (man-made or natural) via the cleat network. Fractures and cleats are the major parameters that influence gas flow capacity because deliverability of the CH4 to the production well is controlled by the cleat permeability. As gas production continues over time, CH4 desorbs from coal, and coal matrix volume starts to decrease. This volume decrease in the matrix opens up the cleats, matrix shrinkage, which leads to a permeability increase. Several emprical (Harpalani and Schraufnagel 1990a, 1990b; Harpalani and Chen 1995, 1997; Harpalani and Mitra 2010; Pan et al. 2010; Liu et al. 2012; Mitra et al. 2012) and analytical (Palmer 2009; Liu and Harpalani 2013) studies have reported this relationship between pressure and permeability. Those studies showed that permeability is an important parameter in CH4 production performance. Furthermore, during gas production, water is produced through the cleat system as well, therefore gas-water relative permeability must be also considered in evaluating production performance (Gash et al., 1991). In the CO2 injection scenario the opposite occurs because CO2 has a higher adsorption affinity than CH4. CO2 replaces CH4 in the matrix of the coal and increases the volume of the coal matrix, matrix swelling, and results in a permeability decrease. Harpalani and Mitra (2010) concluded in their experimental study that swelling of the coal matrix due to the CO2 injection is two to three times more than the sorption of CH4, resulting in large permeability changes during CO2 injection."

Jan 1, 2016

By A. Halim, J. Gustafsson, A. van Wageningen, J. Johansson, · J. Lööw, K. Kocsis

A major part of the European Union’s (EU) project Sustainable Intelligent Mining System (SIMS) is investigating the development of diesel-free/carbon–neutral underground mines in order to ensure sustainable underground mining in the future. Replacing diesel machines with electric vehicles in underground hard rock mines has been widely acknowledged by the mining industry worldwide as a critical step to improve working conditions by reducing diesel exhaust–related contaminants, to reduce mine ventilation electrical power cost by reducing mine airflow quantity, and to reduce mine greenhouse gas emissions. All of these are major requirements to achieve sustainable future underground mining practices. A field trial of Epiroc’s 2nd generation of Battery Electric Vehicles (BEVs) at Agnico Eagle Finland’s Kittilä mine was conducted during 2019–2020. Vehicles tested were MT42 mine truck, ST14 Load-Haul-Dump (LHD), and Boomer E2 jumbo drill rig. This paper outlines the improvement of the working conditions observed in the field trial, and the opinions of the mine personnel at Kittilä mine on using BEVs instead of diesel machines. Measurements of atmospheric contaminants and air temperatures taken during the field trial clearly demonstrated a significant improvement of working conditions when BEVs were operating as opposed to diesel machines. This field observation was supported by the opinion of the majority of the Kittilä mine workers. However, some remaining concerns must be addressed before BEVs can replace diesel machines.

Oct 25, 2021

Operation of a pilot-scale Floatex density separator was studied using a pyrite concentrate slurry feed. Experimental measurements were further utilized in parameterization of a hindered settling simulation model. The model incorporates particle slip velocity calculation and also a separation efficiency function, adjusted to describe the feed material characteristics. The model was used to compute the overflow and underflow compositions when both fluidization bed pressure and teeter water flow rates were varied. In addition, prediction accuracy and the model validity were evaluated. The simulations gave good results when the teeter interstitial velocities were moderate enough to avoid excessive turbulence in the fluidization. Prediction of the cumulative overflow and underflow size distributions in most experiments yielded essentially less than 10% relative error between the sample data and the estimated value of the 50% passing sizes.

Jan 1, 2011

By R. Q. Honaker

Although the fundamental principles of hindered bed classifiers are relatively simple, the complex interactions between the operating parameters provide a degree of difficulty that hinders the ability for on-line plant optimization. Thus, a dynamic population balance model was developed for determining the hindered settling velocity of particles varying in density and size. The steady-state results of the model include partition curves as a function of particle size and density as well as metallurgical data. A statistical comparison of the simulation results with those obtained from industrial units reveal a high level of accuracy with adjusted R2 values greater than 0.95.

Jan 1, 1999

By Jim Clark

Tunnel boring machine (TBM) tunneling is an ever-increasing prospect for underground construction, and, with each new tunnel bored, there are unknown elements. When boring through the earth, even extensive geotechnical baseline reports can miss fault lines, water inflows, squeezing ground, rock bursting and other types of extreme conditions. This article draws on the consider-able field service experience within Robbins to analyze successful methods of dealing with the most challenging conditions encountered. Many tunnel projects are located in areas with relatively poor access along the tunnel alignment and bored under extremely high overburden. These two factors often result in limited geological information. It would be reason-able to state that the deeper the tunnel, the greater the lev-el of uncertainties. When faced with these uncertainties everyone involved with the project including the owner, the contractor and the machine supplier must be prepared to tackle geological surprises. This article describes the problematic geological conditions and associated difficulties faced on three separate projects and the measures that were taken to overcome these difficulties.

By Efstratios Karampinos, John Hadjigeorgiou, Philippe Morissette

"Ground support is a critical element in maintaining the stability of mining drives in deep and high stress mines. In challenging ground conditions, it is necessary to continuously explore ground support strategies that can control the resulting large deformations. It is an objective of mining operations to optimize the ground support by selecting appropriate systems at the time of installation of each reinforcement element. A successful ground support strategy will result in the use of a system that ensures both the structural and operational integrity of the excavations and mitigates the need for rehabilitation.Preliminary ground support design is often based on empirical observations and methods. Once a design is implemented, field trials, observations and in situ pull tests are used to fine tune or improve the design. Although not often employed during this process, numerical modelling can provide helpful insights into the impact of different ground support strategies. In this respect, it is possible to explore the use of multiple options before selecting the most promising ground support system for implementation in field trials. The challenges associated with the numerical modelling of rock support for mines have been described by Lorig and Varona (2013) and Potvin (2017). The employed numerical models should capture all potential failure modes of reinforcement throughout the mining sequence of the excavation. In particular, it is important to emulate the observed in situ ground support performance, as well as the influence of the installation sequence of the support. However, the time and expertise required for this type of modelling of ground support is often not available at mine sites. Even when the expertise is available, it requires a major time commitment and commitment of resources to set up, run and calibrate the sophisticated models capable of explicitly capturing the behavior of ground support.Rock reinforcement is an integral part of all ground support systems used in underground mines. Long, flexible tendons can reinforce the rock mass deeper into the walls and create a thicker reinforced shell around the underground excavation. This article focuses on the optimization of the cable-bolting strategy in squeezing conditions at the LaRonde Mine in Quebec, Canada by integrating the 3D distinct element method (DEM) in the design process. A calibrated numerical model is used to investigate a series of cable bolt configurations and provide recommendations for the ground support design."

Jan 4, 2018

By Samuel S. Adams

The Permian Salado Formation of west Texas and southeastern New Mexico is composed of halite and subordinate amounts of anhydrite, clay and potassium and magnesium-bearing evaporite minerals. Aspects of the geochemistry of the Salado Formation have been investigated through studies of the stratigraphy, mineral assemblages, textures and minor element content of the salts. These studies provide information on the origin of the evaporites when combined with data on equilibria in saturated salt solutions. The principal potash ore zone in the district is composed essentially of halite (NaC1) and sylvite (KC1). Data on the color, bromide content, and proportions of halite and sylvite suggest that this simple assemblage is the product of a series of replacements rather than primary precipitation. The bromide content of the salts also indicates that the brine which precipitated the Salado Formation was derived from the dissolution of older evaporites rather than the simple evaporation of sea water.

Jan 1, 1966

By R. E. Hamilton

Automation is a word whose meaning has been broadened by popular usage to include any labor saving device. We with restrict our usage to the replacement of human judgement by instrumental measurement and mathematical analysis in the control of industrial processes. Mineral concentration is an area which has resisted automation because of the great difficulty in developing measuring instruments which can exist in the rugged environment and can measure useful properties with acceptable accuracy. This is not the only factor limiting progress, but until recently it has been of over-whelming importance. The development of on-stream X-ray analysers, magnetic flowmeters and nuclear density meters for mineral slurries has eliminated this obvious barrier and is enabling us to locate and attack the less obvious problems which still limit our ability to automate concentrators. If we examine the history of automation in industries which are highly automated we find that it has usually gone through three distinct phases. The first phase has been regulation. This is the simplest form of control and involves manipulating some variable whose value is of no importance in order to maintain the value of some other variable which is important at a constant specified value in spite of disturbances which may occur in other variables which affect it. A simple example is the use of a control valve to maintain a constant flow of fluid in a line in spite of changes in pressure in the vessels at the ends of the line. The position of the valve stem is of no consequence, as long as it is within its operating range. Unfortunately we soon run out of variables which can be

Jan 1, 1971

By Eric Jacobs

"Building and operating tunnels has been a highstakes endeavor in terms of costs, complexity, safety and impact on contractors, owners and the public for a long time. There are many variables that need to be closely monitored and managed to construct a tunnel on-time, on-budget and safely. Once built, there are also many elements that need to be monitored and managed to operate a tunnel safely and efficiently.Fundamentally, the risks to the safe and efficient construction and operation of a tunnel are a function of the degree of harm and the likelihood of the harm occurring. From a cyber security perspective, risk assessments used to inform decision makers and support risk responses are typically based on identification of relevant threats; internal and external vulnerabilities; the impact that may occur given the potential for threats to exploit vulnerabilities and the likelihood that harm will occur. This article focuses on creating awareness of vulnerabilities associated with technology used in tunnel construction and operation and some of the challenges associated with remediation of these vulnerabilities. As we all know, technology has been evolving at an accelerating pace and infiltrating every aspect of our lives in new and often exciting ways. In the world of tunneling, sensors and systems that provide position and time have become accurate, rugged and cost-effective enough to come out of the research labs and into the equipment and systems used every day. There are many opportunities to employ connected computing devices and sensors to costeffectively capture, integrate and analyze key data with minimal latency to manage risk better, improve safety and avoid surprises."

Jun 1, 2019

By S. Dereski, G. Chancellor

"INTRODUCTION Barrick Goldstrike underground mine is located in Northern Nevada on the Carlin trend. The underground mine produces approximately 1.5 to 1.8 million tons a year and approximately 400,000 ounces of gold a year. The mine is comprised of two main mining methods, underhand drift and fill and long hole stopeing. The mass blast project stated in 2012 as Value in Use project between Barrick, Southwest Energy and Orica, the goal of this project is to be able to blast an entire drilled stope in one blasting event instead of taking multiple blasts. This will improve productivity by eliminating intermediate blasts, reducing additional blast time, eliminate drill hole cleaning due to the previous blast. Project implantation started in the fourth quarter of 2013 and mass blasting has been common practice throughout all of 2014. STOPPING PRACTICE AT GOLDSTRIKE BEFORE MASS BLAST PROJECT The production from the Goldstrike mine is approximately 70% from stopes. The timely completion of all stoping blocks is imperative to maintaining the plan, delays in the execution of any particular block can have detrimental ripple down effects as neighbouring stoping blocks become delayed. Before the implementation of this project the standard practice for Goldstrike was to: 1. Drill the entire stope 2. Blast a bottom shot, normally between 10 feet and 20 feet off the bottom of the slot rings. This would be mucked out before the next shot 3. Blast a pull through shot, this included the raise and one or two production rings. Again mucking this out before the next shot 4. Blast production rings, one or two more blasts depending on stope size. In most cases between each of these blasts the holes in the other rings of the stope would have to be cleaned. This meant either cleaning manually using air and water, or mechanically cleaning with a bench drill. In many cases this resulted in delays in completing the stoping block."

Jan 1, 2015

By B. J. Arnold

Prior laboratory work has demonstrated -that much of the fine ash-forming minerals entering a flotation froth are there as a result of water carry-over from the bulk contents of the flotation cell (Arnold and Aplan, 1986a). Using a bank of four 300 cu ft WEMCO flotation cells cleaning a well-liberated Lower Kittanning seam coal, test results show that the sulfur and ash content of the froth is directly related to the water content of the froth (or inversely related to the percent of solids in the froth). Reagent changes which result in a watery froth produce a higher ash content in the froth. A direct comparison of laboratory and plant results show that the standard laboratory flotation test produces a product higher in sulfur and ash than that produced in the plant. Caution should be exercised when extrapolating laboratory test results to the plant situation. A method of estimating coal flotation product quality in the plant based on laboratory tests is given.

Jan 1, 1990

By O. F. Brown

Excavation and loading are primary operations in the surface mine production chain, constituting a significant component of production costs. This makes excavation and loading important cost centers that need to be improved to lower production costs. Optimizing the design and use of excavators will improve energy efficiency in earthmoving operations, and this requires a thorough understanding of the soil-tool interaction process. Modeling the interaction process accurately is the key to this optimization. Experimental and analytical methods have provided limited information on the behavior of soils during excavation. Finite element (Fe) analysis of soil-cutting blade interaction produces some advantages over experimental and analytical methods. However, the soil constitutive equations used in most of the available Fe analyses fail to adequately model the plastic behavior of the soil. This work uses Fe modeling to study the behavior of formation-cutting blade interactions in dozer excavation. The formation is modeled as a nonlinear elastoplastic material using the modified cam-clay (mCC) model. The model accounts for soil-tool interface friction, and progressive and continuous cutting at the blade tip. The results provide soil forces, a progressive developed failure zone and soil displacement fields. The sensitivity analysis of changes in blade angle on cutting force shows that the cutting force increases with increasing blade angle. The cutting depth of the blade had a similar effect on blade cutting force. Increasing the depth of cut increases the required cutting force. Increasing the coefficient of friction at the soil blade interface increases the blade cutting force. Reducing the coefficient of friction at the soil blade interface from 0.3 to 0.05 reduces the cutting force by 22.3%. The percentage represents the maximum potential savings in blade cutting force. This research initiative advances the frontiers of soil-tool interactions during excavations to expand the limited knowledge in this critical area.

Jan 1, 2012

By Alexander N. Winchell

The construction and erection of the Coleraine concentrating plant was commenced in April, 1909, and was completed (with the machinery installed) ready for use in 1910. Attached to the main building is 'a table house large enough to accommodate con¬centrating tables for five units and space for a small machine shop and supply store. For the handling of the' railroad cars in the upper portion of the mill there is provided on the north side of the main structure a trestle approach 650 feet long, and on the south or opposite side a tail track 300 feet long. The latter is so constructed as to permit its being incorporated directly in a possible future extension of the plant. The building, viaduct approach and tail, trestle, as well as the table house, are con¬structed of steel, the total amount used being 6,100 tons. The building is covered by corrugated' steel sheeting over 2 x 6-inch wood sheathing fastened directly to the structural steel. The north end of the trestle approach is connected with the main road-beds forming the track system for delivery of the crude ore to the plant over an embankment of a maximum height of 110 feet containing over 2,000,000 cubic yards of dirt.

Jan 1, 1920

By H. L. Lovall

Huge banks of preparation plant refuse and other non¬saleable materials have accumulated over the years in all major United States coal producing areas. These banks, esthetically and commercially undesirable, can cause air and water pollution and land reclamation and mineral conservation problems for the industry and nearby communities Although some refuse banks have been reworked to recover saleable coal, all remain and accumulation continues. Even those previously processed continue as potential hazards. Among the several problems created by refuse banks, in situ combustion is most treacherous. Of the millions of tons of major accumulations, there are at least 450 refuse banks on, fire at this time Attempts to extinguish such fires are costly, impractical and generally unfruitful. Studies are in progress to evaluate the potential of processing such materials to eliminate the combustion capability and to yield usable fuel and nonfuel products. Aspects of the study now in. development for coal refuse include: (a) evaluation of characteristics (size, sink-float, ash, sulfur and calorific value) of the coal refuse materials which are known to be highly variable, (b) development of an ignition test having significance for in situ conditions, (c) study of processing capabilities (comminution for liberation, pilot plant washing tests), and (d) investigation of potentially significant properties of fuel and nonfuel products which could be altered to enhance their market potential.. Among the latter products are lightweight aggregate, fill for mine slushing operations, construction, etc: Plans are to extend the studies to include the design, erection, and test processing of refuse with a transportable plant,; which could provide basic economic and product utilization data from several locations

Jan 1, 1964