Search Documents

By Edward Holloway

The basis for the selection of the ultimate pit for an open-pit mining operation is generally opaque. Some form of value-based analysis will generally guide the final decision; however, the value will often gradually plateau while the ultimate pit size continues to increase. There is no established framework to guide specialists in the selection of the ultimate pit, with such decisions regularly made on a somewhat arbitrary basis. The key component that is missing from the analyses typically used to select the size of the ultimate pit is risk. Once risk is quantified within the analysis framework, the decision-mak-ing range is significantly reduced and the process for select-ing the ultimate pit becomes more consistent, replicable and defensible. The technique outlined in this paper provides an approach to including risk in the process used to select the ultimate pit.

Jun 1, 2024

By F. Dehghani, B. Rezaie, T. Ghosh, A. Sachan

Comminution is an integral part of the mineral extraction process. However, the influence of the comminution method (ball and rod mills) on silica and magnetite particle shapes has not been substantially investigated. Shape parameters for fractions of -250+212, -150+125, and -106+75 μm sizes were examined utilizing a scanning electron microscope and a Clemex vision PE image analysis system. The silica particles displayed higher elongation and flatness parameter values for rod mill products, but roundness and relative width parameter values of rod mill products are less than that of the ball mill products. Magnetite particle elongation and flatness parameter values of ball mill products in fraction sizes of -250+212 and -106+75 μm are larger than rod mill products, but roundness and relative width parameter values of ball mill products are smaller than rod-mill products, but for the -150+125 μm size range the result is converse. Furthermore, particle elongation and flatness increased with decreasing particle sizes of silica, whereas, roundness and relative width decreased for both Ball and Rod Mills. In case of magnetite, ball mill products displayed an increase of flatness and particle elongations with decreasing particle sizes but flatness increased and roundness and relative width decreased. Similarly for rod mills, magnetite fractions of -150+125 μm were found to have the largest values of elongation and flatness. INTRODUCTION Comminution alters the size and shape, causes lattice distortion, changes chemical composition, surface area, surface-free energy, and polymorphic transformation of all materials. The quantity and quality of such changes depend on specifications of the material feedstock, the type of mill being utilized, the specific energy input, ambient temperature, and environmental pressure [1]. The shape difference between the milled products depends on different grinding mechanisms and the respective breakage principles that these mechanisms depend on [2, 3]. With decreasing particle sizes, the nature of the particle surface become crucial [1]. The influence of the breakage technique has been found to be non-trivial and heavily dependent on the type of grinding mill used for particle size reduction [4]. Shape is an important industrial parameter for predicting particle behavior in downstream processes. The shape parameter affects the way particles burn, compact, are recovered, flow in fluids, sinter, float, agglomerate, fluidize, interact with pulmonary tissue, cut, abrade, react with chemicals, form structural materials, and retain and permit fluids to flow [5, 6]. The distribution of particle sizes and shapes are important for mining, civil and chemical, pharmaceutical, and various other industries with interest in the population modeling of atmospheric dusts, smoke, and grit [1, 3, 6]. The shape parameter not only affects the chemical, physical, surface properties of particles but is also important for downstream processes [5, 6]. Image analysis has been found to provide detailed information about size and shape of the particles and can be used for the control of product quality [4].

Jan 1, 2019

By Gilles Recher, Jörg Riechers, Albert Lueghamer

"INTRODUCTIONIn view of a global trend towards urbanization, more and more trunk sewers and combined sewer overflow tunnels (CSO) with medium to large diameters and the corresponding link sewers are currently built and under design. Shielded tunnel boring machines using segmental lining as tunnel support represent an efficient solution for construction of new wastewater and supply tunnels. Especially in the field of sewers, the durability of concrete structures both exposed to any groundwater present on its exterior and to aggressive waste water as well as gases on its interior is a key requirement. Despite thorough research on segmental lining and mechanized tunneling machinery, conventional thermoplastic liners show comparatively minimal progress in terms of practical advancements. This is in contrast with the development of the latest segment embedded high density polyethylene (HDPE) system. Based on experiences achieved, this paper discusses the latest development of an integral protective lining system in respect of material characteristics and its adaptability to both project and customers’ demands. Reviewed performances, as the bondage behavior of the embedded HDPE system at axial stress loads due to acting thrust cylinders during ring build as well as the ability to drain pressurized water behind the embedded membrane, tested at full scale segments, are also presented. The paper is round off by presenting first details of sewer projects endeavoring to utilize this cutting-edge solution for an integral concrete protection, which will be commenced beginning of 2016.CASE HISTORIES ENCOURAGE ADVANCEMENTS Past experience has shown that unprotected concrete surfaces as well as chemical based linings such as coatings, sprayed linings and cured in-place-systems cannot reach the desired life times. Also the fact that in deep tunnel sewer system hardly maintenance is possible, a durable and maintenance free system is required which only can be reached by applying mechanical anchored HDPE (CPL)."

Jan 1, 2016

By K. A. McDonald

This paper will describe the experiences of Hibernia Holdings, Inc. in constructing a mineral processing facility in Mexico. It will attempt to set forth a guideline on what companies attempting to operate in Mexico can expect and what actions they can take. Ownership laws, import/export laws, labor laws, security, transportation and operating experiences will be discussed.

Jan 1, 1994

By Chee Theng

"Mineral processors know you can put in the best technology in the world but it won’t work optimally without the support of the operators. Conversely, you may have complete operator support but won’t get top results without the right technology. When the two come together, the returns can be phenomenal.The first day of talks at the 68th Annual Colorado MPD Conference, held April 26-28 at The Broadmoor in Colorado Springs, covered the ground on these industry wisdoms.Coming together as a team“Think of the people, not just the lab and the numbers. That makes all the difference,” said Dee Kippers, of FMI Henderson Mine, in her talk on “Process optimization during a market downturn (A Moly MacGyver story).” Kippers told an entertaining story of the journey she and her team took in tackling the issue of an annual spike in iron content in the product at Freeport- McMoRan’s Henderson primary molybdenum mine near Empire, CO.As the metallurgists tried one thing after another — cranking up the iron depressant, adjusting pH with sodium hydroxide and hydrated lime, modifying reagent levels — Kippers found that when she shared her results with the operators, communicated with them on what she was doing and got their input, they were more willing to work with her, and more understanding and supportive of her efforts.The results make the case for getting people on board and coming together as a team. The cost savings from their optimization efforts, with little capital investment, have been “enough to cover the annual salaries of our metallurgy department and then some,” Kippers said.Considering the environmentDavid Lemieux, of Dundee Sustainable Technologies (DST), talked next on “Cyanidefree process for gold extraction,” presenting the results obtained from a demonstration campaign of the company’s novel chlorination process for gold extraction and associated arsenic stabilization process. Developed at an investment cost of C$35 million, they are ready for commercialization, having been demonstrated on the laboratory, pilot and demonstration scales.The DST process is differentiated from the Plattner chlorination process, which was in use from 1851 to 1916, by moderate process conditions of atmospheric pressure and ambient temperature — the result of using sodium hypochlorite solution, or bleach, instead of direct injection of chlorine gas — and new, cheaper materials of construction, such as polymers, plastics, fiberreinforced plastics and Teflon, resulting in lower capital and operating expenditures."

Jan 7, 2018

By V. S. Tadsen

Today, man is able to probe space because of technological advancements including the ability to control certain combustion reactions very precisely. The recent adjustment of the attitude of Skylab by radio command from earth is an excellent example of such control. It is strange, and indeed unfortunate, that very little is known about the mechanism of combustion of pulverized coal, the primary fuel for rotary kilns. The selection of a coal for direct pulverized firing of a rotary lime kiln may be determined by trial and error, persistence of sales personnel, proximate analyses, grindability, or apparent BTU cost. Occasionally, the only question asked is, "How much lime will it make?" To study the behavior of a particle of coal in the combustion stream of a rotary kiln is most difficult. We must, therefore, discuss the general mechanism of combustion of pulverized coal, and relate this mechanism to the selection of a proper coal for a rotary kiln. The classic three T's -time, temperature, turbulence -must be enlarged upon for a better understanding of the problem. Pulverized coal occupies only 0.01 per cent of the volume of air required for its combustion. This mixture behaves like a gas and the general laws governing the movement of solid particles in gasses are in effect. The differential velocity between air and coal particles depends on forced and natural convection, diffusion, and the length of time each particle is in the combustion space. As a particle of coal absorbs heat from its surroundings, it begins to give off volatiles". These gasses ignite as their kindling temperature is reached, and burn readily because of the excess oxygen immediately available. Combustion proceeds at this stage by the outward diffusion of gas from the coal particle into the surrounding oxygen-rich envelope. We could say combustion at this stage represents a small coal particle surrounded by an envelope of volatiles burning at their point of contact with sufficient oxygen. This release or expulsion of gasses from the coal may result in exfoliation or disintegration of the coal particle. If this occurs, and it is desirable that it should, it will accelerate the final stages of combustion. The escape of volatile material from the particle of coal and its subsequent combustion will cause increased turbulence around that individual particle. Ignition is maintained by radiation from gasses and solids in the combustion system, and most importantly, re-radiation from the kiln refractories and the process load.

Jan 1, 1978

By III Westbrook

Although calcium sulfate dihydrate, commonly referred to as gypsum, has been utilized for some time in fiberglass reinforced polyester (FRP) applications, it does not have the fire retardant filler recognition of ATH. Gypsum is more commonly known for application in cement, soil and water treatment, plaster, and wall-board. Inherent characteristics of gypsum limit its use to low temperature and, until recently, non-aqueous applications. However, as a plentiful, naturally occurring hydrated mineral, the cost effectiveness of calcium sulfate dihydrate has prompted development and yielded success in the areas of FRP spray-up and latex carpet backing.

Jan 1, 1993

By A. H. Summers

The La Choya mine is located 55 km south of Sonoyta in northwestern Sonora, Mexico. Mineralization is controlled by a 40 meter thick thrust fault zone which created a permeable host for the metal-bearing hydrothermal solutions. The ore body is mined by open pit using wheel loaders and truck haulage. Gold and silver are recovered from low grade ore by heap leaching followed by carbon adsorption.

Jan 1, 1997

By Sotiris N. Kamenopoulos, Zach Agioutantis

Rare earth elements (REEs) are considered critical minerals for the industrial and defense sectors. In 2018, the U.S. Department of the Interior presented the final list of critical minerals that are vital to the U.S. economy and defense [1], which included REEs among other mineral commodities. REEs are not rare, despite their name, but economically viable deposits of REEs can be found only in certain geographical areas, and the political and social conditions characterizing these areas may not always be in favor of mining operations. Mining operations may be placed in great operational and financial risk if operations are planned in such areas. Erroneous decisions by decision makers may lead to a chain of events that can completely shut down a mining project. 

By Ying Lu, Jeffrey C. Johnson, Chen-Luh Lin, Jan D. Miller, Sindhoora Puvvada

The amount of energy used to break rock is of interest in mine-to-mill operations to minimize energy consumption during blasting at the mine site and comminution at the processing plant. In this research, a direct energy measurement was made using high-velocity impact to cause breakage of long granite cores, and to study the energy dissipation along the entire bar length. The results show the formation of three zones of damage — fragmentation, fracture and elastic — that have been characterized in 3D using X-ray tomography. The fragmentation zone of the granite bars was studied in detail to describe the particle size distribution and the particle shape characteristics. The experimental energy dissipation in the fragmentation zone was found to be in close agreement with the expected energy calculated from the Bond work index (BWI) equation [1] when the anisotropic granite particles in the fragmentation zone are defined by length rather than by sieve size. The results increase our understanding of rock breakage and energy consumption and may find future applications in mine-to-mill operations.

By Jaeheon Lee, Junmo Ahn, Jae-Yeon Kim, Yoo-Jin Kim, Jiajia Wu, Eun-Woo Kim, Jai-Won Byeon, Jun-Jae Lee

The surge in demand for battery materials, coupled with environmental challenges linked to battery disposal, underscores the need to recycle spent lithium-ion batteries (LIBs). Green recycling approaches, in particular, have garnered attention for battery recycling. In this study, a hydrometallurgical method using a synergetic organic lixiviant combining methanesulfonic acid (MSA) and citric acid (CA) as an alternative to inorganic mineral acids was introduced as a green approach to recycle cathode materials of LIBs. The conditions for leaching and recovery processes were optimized. Cathode materials were regenerated using the recovered materials. Moreover, the leaching performance and economic feasibility of this leaching system were compared with those of various other organic acids.

Feb 1, 2024

By Douglas J. Lacke

1974 marked the start of a new era for Climax Molybdenum Co., a division of AMAX, with the initiation of an open pit operation above the existing successful underground block panel caving mine. A number of problems posed a challenge to the Climax open pit. Highly fractured rock, old mine workings, permafrost, and more than 7.6 m/a (300") of snowfall forced changes in normal operations. Final pit wall design was altered. Production bench heights were lessened due to old workings. These and other modifications contribute to a highly successful open pit operation.

Jan 1, 1981

By Juan J. Monsalve, AMAN SONI, ALEX PFREUNDSCHUH, Nino Ripepi

Ground control failures are one of the main causes of accidents in the underground stone mining industry. Some of the fundamental tools for rockfall hazard identification are related to rock mass characterization and geotechnical discontinuity mapping. Recent technological advances in these methods are related to remote sensing techniques and pointcloud processing software for automated discontinuity mapping. Remote sensing techniques, such as LiDAR and photogrammetry, generate multimillion-point clouds with millimetric precision, capturing the structure of the rock mass. The automated point-cloud processing tools offer alternative algorithm-based methods to characterize and map these discontinuities. However, their applicability is constrained by multiple factors, such as site-specific conditions of the rock mass and the parameters used within the mapping algorithms. This paper evaluates the performance of automated discontinuity extraction software compared with manual virtual discontinuity mapping. Sampling windows from laser-scanned sections in an underground limestone mine are defined and mapped using the Discontinuity Set Extractor (DSE) opensource software. Results from the virtual discontinuity software are compared with manually extracted fractures from I-Site based on reviewing orientation, trace length, spacing, number of extracted discontinuities, and processing time.

By K. V. Raj, C. A. Berry, A. T. Weakley, A. L. Miller, P. R. Griffiths, D. A. Parks

Diesel particulate matter (DPM) has been classified as a carcinogen to humans by the International Agency for Research on Cancer. DPM exposure is therefore regulated by the U.S. Mine Safety and Health Administration (MSHA). The current monitoring process takes days or weeks for exposure levels to be known, and a real-time monitoring device is needed. It is believed that infrared spectroscopy has potential for use in a real-time, field-portable device. This paper presents a method for measuring organic carbon (OC) and elemental carbon (EC) in DPM for a broad range of OC/EC ratios. 

By Dapeng Zhang, Brij Moudgil, Shibo Zheng, Chunhui Feng, Wenyi Song, Wending Xiao, Patrick Zhang

The separation of dolomite from phosphate is the most challenging problem in phosphate mineral processing. More than 50 percent of the phosphate reserve in Florida contains too much dolomite to process using current industry practice. The current way of producing phosphoric acid requires less than one percent MgO in the phosphate concentrate as the feed material. The Florida Industrial and Phosphate Research (FIPR) Institute has collaborated with worldwide experts in the field to address this issue. As a result, the industry is now offered three feasible options. Option I entails three methods for reducing MgO content in the concentrate from the Crago process, including adding a dolomite depressant in the rougher flotation step, dolomite flotation of the cleaner concentrate, and scrubbing the cleaner concentrate in quartz sand, which could reduce MgO content in the final concentrate by 20 to 40 percent. Option II involves the crushing and grinding of high-dolomite phosphate pebbles followed by dolomite flotation at slightly acidic pH using a new collector that does not require phosphoric acid as a phosphate depressant, achieving a final concentrate analyzing less than 0.9 percent MgO at about 87 percent P2O5 recovery. Option III is a gravity separation technique using an innovative separation jig, and its full potential remains to be demonstrated.

By Erik Sundström, Magnus Nygren

The study explores the influence and consequences of safety initiatives on the development of safety cultures in the Swedish mining industry. It involves interviews with experts from four mining organizations, highlighting themes such as organizational structures, safety leadership, feedback, and communication.

Nov 1, 2023

By MARK J. VANARELLI

Estimating ground-water inflows in rock deep tunnels is critical to the safety of personnel constructing the tunnel and the cost of construction. This paper presents two case studies, including the Chattahoochee and Nancy Creek tunnels, for estimating steady-state ground-water inflows into deep rock tunnels. Statistical methods were applied to packer test data obtained from exploratory borings during geotechnical site investigations, and a semiempirical procedure was used to estimate ground-water inflows. The Chattahoochee and Nancy Creek tunnels are deep rock tunnels that exhibit radial flow conditions. For the radial flow condition, a statistical analysis presented in this paper indicates that the semiempirical procedure works well; however, variations in the procedure and/or an insufficient amount of testing could lead to underestimations of the inflow quantities. Modeling using Monte Carlo simulations was observed to be an effective tool for removing data distribution irregularities and incorporating high-end permeability data to derive reasonable ground-water inflow estimates.

By Andrew J. Petruska, Austin F. Oltmanns

The paper proposes a capacitive load cell for detecting changes in material and tool wear conditions for conical picks used in underground mining. The current process is dangerous and subjective, relying on human operators near the cutting interface. The new sensor aims to improve worker safety by allowing operators to perform their functions from a greater distance.

Aug 1, 2023

By Juan J. Monsalve, AMAN SONI, Nino Ripepi, Richard Bishop

The design and strength of pillars are important parameters when implementing the room-and-pillar mining method in a limestone mine. The process becomes complex with the presence of karst voids, which are frequent phenomena in carbonate rock formations. This research continues a previous study aimed at studying the effect of karst voids on the strength of a particular limestone pillar. Using calculated pillar strength and estimated redistributed stresses, it was assessed that the pillar can counter more stress than currently imparted on it. Numerical modeling studies combining in situ stress determination and excavation sequencing were used to estimate the existing stresses on the pillar. Different possibilities of modification to existing pillar design were simulated using distinct element method (DEM) modeling to determine a better design.

Jun 1, 2023

By Ajit Godbole, Ping Chang, Ramakrishna Morla, Purushotham Tukkaraja, Shivakumar Karekal

This paper presents the results of a study on the optimum auxiliary fan location to control air recirculation in dead-end workings where diesel-powered vehicles operate. Investigations were conducted with various secondary fan locations from the dead-end crosscut and with the intake air quantities varied using different auxiliary fans to control air recirculation and diesel particulate matter (DPM).

Jul 1, 2023