Search Documents

By G. Van Weert, J. F. Breedveld

Both regular and Silver Impregnated Activated Carbon (SIAC) were studied for their effectiveness in removing WAD (Weak Acid Dissociated) cyanides from solutions at pH = 10. SIAC has already been shown to be effective in the removal of free cyanide down to 30 ppb or less. The present work deals with complexed cyanides. Zinc cyanide was used to represent the WAD component. At pH=10, in either batch or column tests it was not possible to lower the total cyanide in solution from either 30 or 8 ppm to less than 1 ppm, using SIAC, regular activated carbon as received, or after grinding. Silver (metal) impregnation of the carbon was not beneficial in the removal of WAD cyanide. However, when silver is added as silver ions (nitrate), the cyanide is adsorbed as silver cyanide in preference to zinc cyanide. The latter compound converts to zinc (hydr) oxide. This way, the cyanide concentration in solution can be lowered below 1 ppm, even when zinc cyanide is already adsorbed on the carbon used. A single exploratory test with added copper ions indicated a similar effect for that system.

Jan 1, 2004

By Michael Beyer

Following the last Cholera Epidemic in 1872, resulting in approximately 400 deaths, the City Council of Munich decided to re¬place the former water supply system within the city limits by tapping new water supply areas outside of the city. Since 1883 Munich has been obtaining its water from the Mangfall River catchment located some 35 km to the south. Its most distinguishing characte¬ristics are as follows: 1) the water is free-flowing, i.e., a pumping system is not required as the catchment area is 100 m higher than the city; 2) the water does not normally have to be treated, meaning "spring fresh" tap water. On a daily basis, 300,000 m3 of water flow through the more than 100 year old pipes, accounting for 70% of the city's daily need. There was originally no requirement of a water tight system as strategically installed drain pipes prevented the build-up of exter¬nal water pressure on the lining. As the qua¬lity of today's water has become significant¬ly worse, the tunnels are now in dire need of restoration or replacement.

Jan 1, 1995

By Siegfried Zell

Preface Pipe heading is a customary and proven technology for the underground installation of all types of piping. In over 90 % of all cases, straight pipe sections are used between shaft constructions since, e.g. this follows roadways or it is necessary from the operational aspect due to pipe control methods, e.g. to use a remote control pipe sensor or comparable control devices within sight from shaft to shaft. Frequently, a straight pipeline is impossible, and is replaced by a more or less spatial alignment due to surface conditions, structures in the ground or foundations. This situation applied for the construction of the Nebensammler Neuland (intercepting sewer) in Hamburg-Neuland for sections IV and V. The following paper is not intended as a description of the complete project. It deals mainly with the special features of this pipe heading, with what I believe to be its somewhat unusual route. The task The building authority design issued by the Main Department for Urban Sewerage of the Free and Hanseatic City of Hamburg consisted of the construction of the collector by a pipe heading using NW 1300 pipes in 2 heading sections. One short straight and one long

Jan 1, 1989

By S. K. Mishra, S. B. Kanungo

Because conventional (physical) methods of ore dressing are not suitable for reducing the phosphorus contents of high-phosphorous manganese ores from Andhra Pradesh (AP) and the adjoining area in southern Orissa, India, the adoption of chemical methods becomes imperative. An attempt was therefore made to reduce the phosphorus content of partially beneficiated manganese ores from AP by roasting with sodium carbonate and then leaching with hot water. However, due to the higher phosphorus contents of the manganese ores from Nishikhal mines in southern Orissa, and because of their apparent resistance to dephosphorization by roasting with Na2CO3 alone, a mixture of Na2CO3 and NaCl was found to be necessary to reduce the phosphorus content to below 0.15%. Free-energy calculations at 700°C and above indicated that Na2CO3 (or Na2O as the active component) is a more active reagent than NaCl. Various process parameters, such as the temperature and time of roasting, the amount of sodium carbonate and the temperature and time of leaching, were studied to arrive at the optimum conditions for dephosphorization.

Jan 1, 2000

By J. A. Reizes, C. A. J. Fletcher, T. Jancar

Spirals play an important role in fine coal and mineral processing. To date, almost all spiral designs have been empirically based. Although many operational units have evolved utilising this approach, it does not necessarily lead to optimal spiral designs. This paper presents the preliminary results of a collaborative computational and experimental research program to understand the detailed separation process which will ultimately lead to a parametric assessment of alternative spiral designs through computational simulation. Unlike the empirical approach, a computational simulation is only subject to the fundamental physics of the fluid flow. No prior knowledge of the generic spiral flow is necessary. The computer code implements a robust finite volume technique to predict the three dimensional fluid motion. A height function method is used to model free surfaces and the code is capable of handling arbitrary spiral geometries. Preliminary validation of the computational simulation is carried out through analysis of an existing spiral design -the Mineral Technologies LD9 unit. Computational flow predictions are compared with experimental measurements obtained using a number of techniques, including sampling and flow visualisation, for flow test cases where no solid particulate is present.

Jan 1, 1995

By S. S. Cook, S. E. Paulson

The US Bureau of Mines is conducting core leaching experiments with sulfuric acid on oxide copper ores from the Cyprus Casa Grande and Asarco/Freeport Santa Cruz deposit in Arizona to further the understanding of the leaching process in supergene copper ores as it relates to in situ mining. Leach solutions from atacamite mineralization contained 5 to 30 g/L (0.05 to 0.28 oz/gal) copper and few extraneous ions. Leachant from chrysocolla ores, with grades similar to the atacamite, contained 2 to 9 g/L (0.02 to 0.08 oz/ gal) copper and abundant extraneous ions. Quartz and K-feldspar had no impact on leach solution composition at any acid concentration up to 40 g/L - (0.39 oz/gal) while illite and sericite had minimal impact. Biotite, calcium-rich clay, and limonite have a significant impact on solution chemistry when there is abundant free acid in solution. High acid concentra¬tions increase acid consumption in ores with abundant biotite and limonite gangue. High acid concentrations can be used in ores with quartz, K feldspar, and sericite gangues without increasing acid consumption per unit of copper removed.

Jan 1, 1990

By Robert J. Timko, R. Lincoln Derick

The Bureau of Mines evaluated the integrity of escapeways in a three entry underground coal mine. A center conveyor belt entry (secondary escapeway), was flanked by an intake (primary escapeway) and a return entry. Diesel equipment was used throughout the mine for material and personnel haulage. A carbon monoxide monitoring system, tied to a data recording computer on the surface, was deployed throughout the belt entry and at selected sites in the intake and return entries. Previously, the company had a fire of unknown origin in another mine, which prompted an interest in the performance of their escapeways. An initial, qua1itative evaluation was performed by burning approximately 14 kg of coal at the mouth of the intake entry. The first test was followed by a similar burn at the mouth of the belt entry. These initial trials showed a high quantity of leakage between entries. In several follow-up evaluations, simulated fires, using a tracer gas, were set in the intake and belt entries. Tracer gas concentrations were obtained in all entries at four different underground locations. The results of these tests showed that permanent stoppings could not guarantee isolated, contaminant-free escapeways.

Jan 1, 1989

By D. C. Hatch

At the MacIntyre Development of the Titanium Division of National Lead Company a magnetite-ilmenite ore together with gabbro-anorthosite waste is mined from an open pit by shovels and trucks. The ore from the pits is trucked to ore stockpiles for blending ahead of the crusher and to free the mine from crusher delivery schedules. The ore stockpiles are blended to yield a 16.5 to 17.0 % TiO, crusher feed. This requires mining on an assay cut-off rather than a visual grade cut-off. Highly mineralized ore runs from 20 plus % TiO2 and 30 plus % Fe to 15 % TiO2 and 40 plus % Fe as the ratio of ilmenite to magnetite changes. There are three major ore types in the present pit with magnetite ratios varying from about one to one up to three times as much magnetite as ilmenite. Ilmenite and magnetite together liberate from gangue down to about 10 mesh and this is the basis of the magnetic cobbing. Below 10 mesh the ilmenite and magnetite start to separate and ore cobbing pulleys will not hold the ilmenite.

Jan 1, 1968

By C. H. McGuirk

Computerized Preventive Maintenance is important in maintaining consistent and efficient operation in any industry utilizing sophisticated and expensive equipment on a continuous basis. At today's large bulk materials handling facilities, the problems of continuous operation of complex machines with their thousands of components exposed to abrasion, dirt, dust and the elements, are intensified and multiplied. Effective preventive maintenance can increase profits. Yet, the number of tasks to be performed is so staggering that it is beyond error-free human capacity. The computer must be an essential ele¬ment in any efficient and economical preventive maintenance system. Computerized preventive maintenance techniques have been successfully used in many fields, usually involving highly skilled and specialized personnel working under favorable and controlled conditions. Now, The Pittsburgh & Conneaut Dock Company has developed and is applying a computerized preventive maintenance system that is applicable to the bulk materials handling industry. The "system" has taken many years of intensive effort to develop and has been time-tested and proven during the past years on equipment handling materials with rugged physical characteristics and corrosive and abrasive qualities, under some of the most adverse weather conditions on the Great Lakes.

Jan 1, 1976

By William M. Gray

[The products of mites hive historically beet a very large and important segment of total shipment transported by American Railroads. Much as the Mining transportation Executives right have wished for coal and other mineral deposits to be found along navigable rivers, where railroads have for years been competing with the very aggressive Army Corps of Engineers and the inland waterway operators, the mineable reserves are more often that not located in the arid west far from these "free" waterways. The rivers cannot go to the mines but the railroads could, did, and continue to invest it new lines to reach new mines. The mining industry and the railroad industry have good reason to rely upon each other. The former Northern Pacific Railway, the Great Northern Railway, the Chicago, Burlington and Quincy Railroad and the Spokane, Portland and Seattle Railway merged in 1970 to form the Burlington Northern Railroad, with Lou Menk as its first President. As unofficial spokesman for the industry, be had, for years, conducted a tireless effort to educate shippers, lawmakers and the general public of the single most critical problem confronting the railroad industry, the strangle bold of government regulator.]

Jan 1, 1985

By Jon G. Baird

The suggestion of the use of measurements of trace amounts of mercury as a guide to the location of sulphide ore deposits was first made by the Russian, A. A. Saukov (1), in 1.946. Since Saukov's original work, many others have studied the abundance of mercury in nature, the association of mercury with sulphide ores and methods by which very minute quantities of mercury can be measured in air, soil, rocks, water and plants. The most abundant of the mercury bearing minerals is cinnabar (HgS). Native mercury is also found and sulpha-salts like tetrahedrite are known to have important mercury contents. Other sulphides of base metal deposits contain mercury in amounts ranging from parts per million to as much as one or two percent. (2) The mercury content of sulphide-free rocks is usually less than a few hundred parts per billion (1 ppb - 10-9), Soils usually contain less than 100 ppb and water less than 1 ppb of mercury. Normal atmospheric air contains about 1 nanogram (10-9 grams) of Hg per cubic metre although higher concentrations can be observed near mercury occurrences, sulphide deposits and volcanic exhalations.

Jan 1, 1973

Microorganisms have been widely used for hydrometallurgical operation and effluent treatments(Smith, et. al., 1991a; Gadd, et. al., 1986; Darnall, 1986; Paponettis, et. al., 1991; Mihaylov, et. al., 1991; Rusin, et. al., 1991; Noble, et. al., 1991; Yang, et. al., 1991). In recent years there is a growing interest in using microorganism for flocculation of minerals fines and flotation collector (Smith, et. al., 1991b, 1991c; Misra, et. al., 1991a, 1991b, 1992a, 1992b). It is envisioned that the utilization of nonpathogenic microorganism and/or extracellular surfactant derived from microorganism as a flotation collector will replace some of the environmentally toxic flotation collectors and at the sometime improve flotation efficiency. The selection screening, and judicious selection of appropriate microorganism as flotation collector has been a challenge to process engineers. Over the past five years, continued research at the University of Nevada has shown that certain microorganism Mycobacterium phlei (M. phlei) can be a good flocculating agent and has potential to be used as a flotation collector (Dubel, et. al., 1992; Misra, et. al., 1991a, 1991b, 1992a, 1992b; Smith, et. al., 1991d; Chen, et. al., 1992a, 1992b)).

Jan 1, 1993

By S. L. Ducummon

Inactive underground mines now provide essential habitat for more than half of North America's 44 bat species, including some of the largest remaining populations. Thousands of abandoned mines have already been closed or are slated for safety closures, and many are destroyed during renewed mining in historic districts. The available evidence suggests that millions of bats have already been lost due to these closures. Bats are primary predators of night-flying insects that cost American farmers and foresters billions of dollars annually, therefore, threats to bat survival are cause for serious concern. Fortunately, mine closure methods exist that protect both bats and humans. Bat Conservation International (BCI) and the USDI-Bureau of Land Management founded the North American Bats and Mines Project to provide national leadership and coordination to minimize the loss of mine-roosting bats. This partnership has involved federal and state mine-land and wildlife managers and the mining industry. BCI has trained hundreds of mine-land and wildlife managers nationwide in mine assessment techniques for bats and bat-compatible closure methods, published technical information on bats and mine-land management, presented papers on bats and mines at national mining and wildlife conferences, and collaborated with numerous federal, state, and private partners to protect some of the most important mine-roosting bat populations. Our new mining industry initiative, Mining for Habitat, is designed to develop bat habitat conservation and enhancement plans for active mining operations. It includes the creation of cost-effective artificial underground bat roosts using surplus mining materials such as old mine-truck tires and culverts buried beneath waste rock.

Jan 1, 1997

By B. K. Parekh

Silicon carbide (SiC) can be produced by heating rice hulls to elevated temperature, The product is a mixture of beta crystalline silicon carbide whiskers, particles and unreacted carbon. The silicon carbide whiskers are 0.5 micron in diameter and 50 to 100 micron in length and have been found useful for reinforcing metal and other composite materials. The carbon can be removed by combustion, but this makes separation of the silicon carbide whiskers from particles difficult and a high grade whisker product cannot be made. However, a clean high grade Sic whiskers product can be obtained from the pre-burned converted rice hulls using physical separation processes that are based on differential wetting. Recovery of Sic whiskers from the pre-burned material was found to exceed 90 percent. A modification of the froth flotation process developed during this study is now being used commercially to separate silicon carbide whiskers and particles and to recover a high grade whisker product.

Jan 1, 1985

By P. C. Kapur

For mineral processing spirals, mathematical force equilibrium models are sought to extend the spiral performance envelop. In Part 1 of this report, a complete geometric description of the helical spiral and its trough or channel contour is provided. The secondary circulatory fluid motion in the transverse direction that develops when water flows down a tightly turning curvilinear path and its implications for gravity separation are discussed. Different forces that act on the particle during its passage through the spiral are enumerated and quantified for a better appreciation of their relative contributions and roles in the separation process. Three force equilibrium models from the hydrology literature on sed iment transport are employed to simulate a typical spiral. While the results are promising in that the models mimic the broad performance characteristics of the spiral, what is needed is a more general spiral model taking explicit cognizance of the missing components essential to the spiral description. These are such components as centrifugal force and the steep tangential slope of the channel deck. Results of this latter exercise are deferred to Part 2.

Jan 1, 1996

By Joseph A. Dos Santos

"The subject of this writing was first published in 1998 with the emphasis on the hardware cost comparison. Other costs, such as the required land area and spatial volume, were mentioned but not emphasized, as these were not deemed as important for new projects where the space was appropriated as required. During the last decade, these other costs have proven to be more than equal in importance. These costs are emphasized here through specific accounts of actual highangle conveyor installations that demonstrate the importance and the high-angle advantage An update on the progress in sandwich belt highangleconveyor technology is also provided.Origin and progress in sandwich belt conveyorsCover belts of the 1950s. Large volume, highangle conveying by “conveyors with cover belt, dates back to the early 1950s, when such systems were employed at the bucket wheel excavator boom conveyor in German lignite mines to increase the depth of cut without increasing the boom length. Various systems were developed, patented and built. These systems were not a lasting success for various reasons, which are noted by Rasper[1]. In his 1958 “Review of Cover Belt Systems,” Rasper summarizes the characteristics which are worth pursing and those that should be abandoned. The former are akin to good conveyor engineering. The sandwich belt conveyor model. The first sandwich belt conveyor model allowed calculation of the required hugging pressure to develop the bulk material’s internal friction and preclude material slideback. A modern, accurate version of the sandwich belt conveyor model is presented in Fig. 1. This model depicts accurately a derating of the material cross-section allowing an ample belt edge distance that can tolerate normal belt misalignment without material spillage. The calculations must thus recognize that only part of the hugging pressure is imparted onto the material with the remainder transferred belt edge to belt edge affecting a material seal. Mathematical development of the sandwich belt model is covered by Dos Santos and Frizzell in their 1983 article, “Evolution of Sandwich Belt High Angle Conveyors.”"

Sep 1, 2016

By J. A. Botín

Mining investment decisions are difficult since decision analysis is often based on scarce information. The sources of uncertainty in large mining investment projects are particularly numerous and are present in all evaluation stages. Hence the feasibility decision for projects of this nature will largely depend on how well these sources of uncertainty are managed to achieve bankable risk levels. The risk associated to the construction stages of a mining project is particularly difficult to quantify, mainly because the large number of variables affecting constructive yields, and the complex interactions among constructive resources. This investigation focuses on developing quantitative simulation models and tools to increase the value of a mining project by means of an optimization of the preproduction equipment fleet. The models were validated through their application in the Chuquicamata Underground Mining Project.

Feb 23, 2014

By Ernest N. Wolff

You here are all familar with the myriad of new laws, some enacted and some pending, that affect the mining industry. These laws, for example those dealing with suspended matter, affect us in Alaska as they do you. Likewise, our friends in government, the Geological Survey and the Bureau of Mines, provide us with the same fine services that they do elsewhere. I am not going to speak today about these, but concentrate on one act of Washington, D.C. the impact of which is felt, for now at least, principally in Alaska. A little more than a year ago, I spoke in Spokane on the subject, "Governmental Challenge to Mineral Development in Alaska." I outlined some of the policies of Government which were operating to change the rules under which the industry operates and to alter the relation- ship between government, industry, and the individual. At that time the Native Claims Settlement Act had not been passed, but was on the verge of being so. In reading over what I said in Spokane, I note that I touched on many points where Government was actually challenging mineral development in Alaska. With the passage of the Alaska Native Claims Settlement Act, many of these actions were given a cloak of legality, and machinery was set up to concentrate the drive to tie up the public domain, machinery which will allow govern- mental control and interference with the actions of individuals on something like 90% of Alaska's land surface. This remarkable law is going to affect each and every one of you. Now, a year after its passage, we are only just beginning to see its lesson for the future. It was created by a coalition of powerful groups, who got other groups to support them by promising to deliver something they had no intention of delivering. Alaskan issues are again being used to get various groups not to oppose legislation which will severely harm them. It will help to understand the nature of this new drive if we understand the Native Claims Act and how it came into being.

Jan 1, 1973

By G. Van Weert

Separation of minerals by shape has received little attention, since minerals normally do not break into different shapes during crushing and grinding. However, comminution of consumer wastes generates opportunities for novel separations based on particle shape. For instance, ductile plastics are broken into longer curved shapes, whereas brittle plastics yield angular particles. Using spouting beds for particle separation in water requires controlling the spout's instability. The preferred geometry for such redesigned spouting beds is reported. Plastic cylinders, discs and spheres were separated as a function of rising water velocity and amount of particles in the system. By using 5 mm particles, differences in settling behavior could be video recorded.

Jan 1, 1999

By I. O. Otunniyi

The natural hydrophobic response flotation method for beneficiation of printed circuit board comminution fines (PCB CF) still requires many studies to further basic understanding of the process and the flotation traits that the PCB CF presents. Varying particle size distribution (PSD) and water recovery under the scheme show that higher mass pull, obtained at the finer PSD, gave lower water recovery but higher value loss. The reverse also holds: the least mass pull at the coarsest PSD used, -106 + 75 µm, gave the highest water recovery per unit mass pull with the highest reverse recovery. This is unlike what obtains in primary resources processing, where higher water recovery is often with increased fines entrainment. The reverse recovery loss here is, therefore, more due to entrapment with the heavy mass pull characteristic of the method than to the entrainment of value with water. Other peculiarities of the system observed are discussed, with the goal of improving the performance of the process, and broadening the general knowledge of flotation systems.