Search Documents

By M. Karmis

Subsidence planning and control must be an integral part of mine design in order to minimize the economic impact of underground mining on the surface. Pre-calculation of surface deformations which may cause damage to surface structures must be performed and dam-age criteria must be established, if the response of structures to such movements is to be determined and the extent of damages to be assessed. In this paper the Surface Deformation Prediction System (S.D.P.S.), which can be used to predict accurately the vertical and horizontal parameters of surface movements due to underground mining, is discussed. The Subsidence Response Modeling Program (S.R.M.P.). which can be applied to evaluate the response of buildings to subsidence-induced movements, is also reviewed. Finally, an example is presented demonstrating the applicability of these techniques for subsidence design and control.

Jan 1, 1990

By D. Rucker

Flow models are used to predict the extraction efficiency of metals in rock piles. These models typically use hydraulic parameters obtained through column studies, which assume that the material in the column wholly represents the entire pile and the parameters can be upscaled several orders of magnitude for model evaluation. This assumption fails for parameters that are spatially variable or scale dependent. To overcome these issues, measurements made directly on the heap at the appropriate model scale can be made with the electrical resistivity method. The method aims to map the variations in the electrical resistivity, which can be associated with moisture content, degree of fines, metal content, and leachate concentration. We present an example of calibrating the resistivity with borehole measurements of moisture using geostatistics to show how the resistivity method can be used to obtain a spatial moisture distribution. It was shown that cokriging the resistivity and moisture together gives a more reliable distribution.

Jan 1, 2010

By Syd S. Peng

According to accident statistics (l, 2), roof fall accidents occur quite frequently at the intersections of underground? openings and account for up to 30% of the roof fall fatalities. But this figure will certainly go up considerably if roof falls not associated with any fatal accident are included in the analysis. Unfortunately, nonfatal roof falls are seldom documented. In the underground coal mines, there are two types of entry intersections. One is the three-way (V type) and the other is the four-way (T type) intersections. A three-way intersection occurs whenever the mainline track haulageway turns at an angle into a section haulageway. The four-way intersections by far the most common type in the U.S. under-ground coal mines are formed by the intersections of two entries which are oriented perpendicular to each other or by the intersections of entries and crosscuts. However, crosscuts are frequently driven at an angle to the entry to facilitate machine movements. The four-way intersections formed by this method of crosscut development are angled. At the intersection of two underground openings, the diagonal roof span is wider than the width of each individual opening. This is one of the major reasons why roof falls occur more likely at the intersections than in the entry between pillars. Consequently, special intersection support plans are usually employed (Figs. 1 and 2) for intersections. The most popular practices are to decrease roof bolt spacing 1 ft. less than or to increase roof bolt length 1 to 2 ft. longer than those employed in the entry between pillars (3). The increase in bolt length or decrease in bolt spacing can be applied to all of the bolts in the intersection or employed only for the strategically located bolts depending on the individual mine practices. These rather generalized practices seems to be adequate for some areas but in many cases inadequate for others. Occasionally, the neighboring two lines of chain pillars are staggered such that the crosscuts in one row of chain pillars face the centers of the chain pillars in the neigh-boring rows. This layout forms T-type three-way intersections which are also inadequate for most weak roofs (3, 4). A study was therefore initiated to develop special techniques for intersection supports. The first phase of the study was the analysis of the stress fields for the underground entry intersections. A three-dimensional stress analysis was necessary for this purpose. Unfortunately, the three-dimensional problems of complicated boundary conditions are beyond the existing analytical methods. The three-dimensional finite element method (FEM) was therefore employed in this study. In the analysis, square pillars of 40 feet wide and an entry height of 8 feet were assumed while entry widths varied at 14, 20 and 26 feet. This model was selected to simulate the mine where roof falls data were collected. The second phase of the study was the collection of field data. The sizes of the roof falls including heights, lengths and widths were collected and analyzed. In the third phase study, the results of the first and second phases were compared and discussed. The analysis of field data revealed an arching zone within which roof falls occurred. The arching zone above an entry obtained empirically was compared with the calculated stress contours. Assuming that the bolts must be anchored in the rock strata outside the arching zone, the preferable systems of bolting were proposed. Also the amount of pretension required to inhibit sliding between layers was discussed.

Jan 1, 1978

By Richard Emberley, Timothy Shaw, José L. Torero, Jurij Karlovsek, Timothy Gibson

"Tunnel closures are highly undesirable and the lengthiest are generally attributed to structural failures (e.g. Mont Blanc). Although historical data shows structural failures are closely linked to fire, design parameters for tunnel safety are not well defined. Current research has focused on defining the fire heat release rate and temperature, but these parameters cannot be easily used to determined structural performance. The energy transferred to the structure, the heat flux, is required but current literature lacks these values. Full scale experiments were undertaken on passenger vehicles resulting in heat fluxes between 20-70kW/m2. Analysis shows a vehicle fire’s duration is closely linked to its mass. Further analysis shows small vehicle fires can be scaled as a function of the tunnel diameter and the characteristic height of the desired vehicle. The present work provides engineers an appropriate design methodology to undertake informed thermal-structural analysis to minimize the risk of tunnel structural failure.INTRODUCTION Quantifying the effects of a tunnel fire depends on many factors such as the type of occupants, their vehicles and spacing, ventilation conditions and the geometric shape of the tunnel (Ingason and Lonnermark 2011). For design engineers investigating the thermal-structural performance of a tunnel, these factors are typically converted into spatial and temporal temperature distributions (Usmani et al. 2001) using various design curves such as those of ISO834-1, Hydrocarbon, Rijkswaterstaat (RWS) or RABT-ZTV (Promat 2013). However, to define a temperature profile through a structural element these curves require a heat transfer model that incorporates an appropriate boundary condition. The appropriate boundary condition is the net heat flux which is the result of a complex energy balance. For use in heat transfer calculations the net heat flux must account for the tunnel geometry as well as thermal properties of a given structural element and all other surfaces and mediums affecting the transfer of heat (Torero 2014)."

Jan 1, 2016

By A. Haghighat, B. Lattimer

"Mine face ignition due to a high levels of methane is one of the most common fire incidents in underground coal mines. This work exams ignition scenarios in continuous miner headings. Depending on the magnitude of the ignition or resulting fire, the ventilation curtain in the continuous miner (CM) heading may be damaged or dislodged, affecting the ventilation into the area. A computational study was conducted to investigate the effects of different levels of damage to the ventilation curtain on the ventilation flow into the CM area. The computational fluid dynamics software Fire Dynamics Simulator (FDS), Version 6.0 was used to predict the conditions that develop due to a 200 kW fire in the coal mine face following a methane ignition with different levels of curtain damage. Smoke layer depth, temperatures and mass flow into the CM area were used to evaluate the impact of no damage to the curtain, partially dislodged curtain, and fully removed of the curtain. Partial removal of the curtain allowed more smoke to accumulate in the CM area and a reduction in ventilation into the CM area. With full removal of the curtain, the smoke accumulated through the entire depth of the CM area and flowed out the entrance to the CM area and the ventilation completely bypassed the region. INTRODUCTION Active working faces in underground coal mines are one the most hazardous locations in terms of fire events. According to Mine Safety and Health Administration (MSHA) data analysis, the highest number of non-fatal fire incidents was reported at mining faces, intersections and crosscut areas in comparison with other locations from 2000 to 2012. About 464 fires happened at active working faces from 2000 to 2012, most consisting of a methane ignition, in some cases followed by localized fire. These are high risk incidents due to the potential to raise float dust and damage ventilation systems, particularly auxiliary systems such as curtain or tubing. Depending on the magnitude of the ignition or fire, the ventilation curtain in the continuous miner (CM) area may be damaged or dislodged, affecting the ventilation into the area. Five computational fluid dynamics (CFD) scenarios were considered to investigate the smoke layer depth, temperature, visibility, mass flow rate, and the behavior of airflow in an entry with a continuous miner (CM) located in it. The state of the auxiliary ventilation was varied based on the assumption that as an ignition increases it magnitude it will affect ventilation curtain proportionally. Visibility and temperature along the height of the entry at different sections were investigated and the interface height at each section was determined. Also, the fresh air height was studied for tenability analysis in future. FDS, Version 6.0 was used to predict the conditions that develop due to a 200 kW fire on the coal mine face following a methane ignition with different levels of curtain damage. Smoke view software was used as the post processor to visualize and analyze methane fire behavior at the face. Most entry fires are reported as fuel-controlled fires as they are rarely restricted to air access (Ingason et al, 2014). The working face fire in the following models was assumed to be a fuel-controlled fire."

Jan 1, 2016

By Fulian He, Jianhang Chen, Dongdong Chen, Shoubao Zhang

"The Wangjialing Coal Mine is the main colliery of the China Coal Huajin Energy Limited Liability Company. The average thickness of the coal seam in District 201 is 6.21 m. Fully mechanized longwall mining was used in this district. The ventilation roadway of panel 20102 was influenced by the retreat mining of the adjacent panel 20104. Therefore, large deformation and severe roof falls occurred in this roadway, seriously influencing the safety production of this coal mine. To support the roadway, cable truss was proposed to strengthen the reinforcement of this ventilation roadway. First, numerical simulation was used to optimize the reinforcement parameters, including the cable installation angle, cable length, and eccentric distance. Based on numerical simulation results, in-situ tests were conducted in the ventilation roadway of panel 20102 with the cable truss technology. In-situ monitoring results showed that the roof-to-floor convergence and the convergence of roadway on two sides were within the safety range. Furthermore, no apparent separations occurred in the roof. These indicate that based on the designed parameters, the cable truss system can effectively maintain the roadway stability under the severe influence of the adjacent longwall mining.INTRODUCTIONCable bolts are flexible tendons composed of multi steel wires, which are wound into a strand (Chen, Hagan, and Saydam, 2018). They were initially introduced in the hard rock mining industry in the 1960s. Later, they found rapid application in coal mines to maintain the stability of excavations (Wang et al., 2015).The standard cable bolt is composed of seven steel wires with a diameter of 15.2 mm. Laboratory and in-situ tests showed that there is a low bonding capacity between the standard cable bolt and the grout (Craig and Holden, 2014; Chen, Hagan, and Saydam, 2018). Then, modified cable bolts are developed based on the standard cable bolts. They are improved by changing the surface geometry of standard cable bolts, such as birdcaged cable bolts (Hutchins et al., 1990) or nutcaged cable bolts (Hyett et al., 1993). Further tests proved that modified cable bolts have better mechanical interlock and friction between the cable bolt and grout, leading to larger load transfer capacity of cable bolts.Although cable bolts have been used for many years, failure of the cable bolting system still occurs. A common failure mode is the damage of surrounding confining medium while the cable bolt is still hanging in the roof, which is caused by the bond failure of the cable/grout interface (Hutchinson and Diederichs, 1996). To prevent the cable bolting system from failing, the cable truss system is more widely used in mining engineering."

Jan 1, 2019

By D. K. Mynear, J. S. Gardner, S. Mittle, A. A. Campoli

West Virginia, although having adequate solar insolation, has witnessed very little actual solar development to date. The reasons for this lack of development are varied, but the primary obstacles to future development appear to be the absence of state-level policies and regulations promoting growth in the solar industry. West Virginia possesses large tracts of under-utilized land throughout the state created by previous mountaintop mining operations that could theoretically be re-purposed for solar farm development. Accomplishing this task will require not only revisions to the current legislation, but also acceptance by utility companies, landowners, and mining companies. Solar developers will need confidence that they can secure revenue from the electricity and Renewable Energy Certificates (RECs) generated by solar projects. Additionally, solar companies will need assurance they will be protected from any non-related environmental liabilities that could arise in the future. The primary avenue in bringing significant solar development to West Virginia will come through large corporate clients demanding or partnering with utility companies for incorporation of solar options into their energy portfolio to help meet established sustainability goals. This scenario has been witnessed in other states where a large client demands renewable options. Solar development could also represent a means through which mine operators might alleviate some of their reclamation and bonding obligations; where the landowner could supplement income from their underutilized land holdings; and where displaced miners could be repurposed in solar installation/maintenance jobs. Utilizing data from the West Virginia Permit Database, this report identifies several mine sites that hold potential for solar development in the future. INTRODUCTION The diversification of energy sources in the United States (US) has seen major shifts during the past decade resulting from: • A sudden abundance of low-cost natural gas becoming available through advanced horizontal drilling and hydraulic fracturing techniques. • Incentive-driven policies leading to new development in alternative energy. • The emergence of renewable energy sources, proliferated by state and federal level incentives and falling capital costs. Coal was once the primary low-cost fuel source for the generation of electricity in the US for most of the last century, providing approximately 50 percent of the total production capacity. However, within the past decade lower-cost natural gas has overtaken coal as the primary source of fuel used in electricity generation, and renewable sources have steadily grown to account for approximately 10 percent of the overall mix.

Jan 1, 2019

By H. A. Stoess

The Minerals Industry makes heavy demands for and on its Material Handling equipment. It also gives progressive management the opportunity for considerable savings, ad consequently increased profits. In some cases, cost of Materials Handling amounts to 40°/o of the total cost of the ultimate product. Handling costs are hidden in overhead, indirect labor, excessive maintenance, productive workers performing handling tasks, and, a great many more. Even though Materials Handling is the oldest occupation of mankind, it is only within the past twenty years that it has emerged as a specialized field. While this industry has made full use of all types of mechanical and vibratory conveyors, pneumatic conveyors in their proper application can be a distinct asset. me use of pneumatic conveyors by this industry however is limited- to a certain extent by the particle size of your products through the various phases of manufacture, as well as their bulk density. However, with increasing knowledge of the fluidization of dry materials, their use is becoming more wide spread.

Jan 1, 1962

By Ingo Ossenbühl, Wolfgang Dolsak, Vojtech Gall, Axel G. Nitschke

"Yielding support systems for application in underground construction have a long history, primarily in mining. Typical examples are tunnels subject to loading conditions that lead to overstressing of the newly installed support or existing tunnel structures in active fault zones. Recent applications for tunnel rehabilitation projects unveiled the capabilities and flexibility of combined yielding support systems presented in this paper. Frequently, the main requirements for tunnel rehabilitation applications are a fast, safe, and simple installation along with the need for flexibility with regards to existing tunnel geometries. A combined support system consisting of steel sets with yielding connections and special groutable hoses has proven to be an efficient support measure providing a multitude of advantages compared to conventional rehabilitation approaches. The presented yielding support system provides an immediate and active support, while it allows for controlled yielding upon experiencing loads beyond its support capacity. INTRODUCTION The excavation of underground spaces leads to redistribution in the existing stress regime. This load redistribution goes along with deformations in the surrounding rock mass. Magnitude and duration of these deformations depend on the tunnel’s depth and geological conditions, but also on the installed support system. Modern civil tunneling infrastructure has generally an envisioned service life of about 120 years. Conventional tunneling provides typically a dual support system, split into the initial (or primary) and final (or secondary) lining. A typical design principle in civil tunneling is to let the vast majority of deformations acting on the initial lining cease, before the final lining is installed. Based on this approach, the loading on the final lining is significantly reduced and signs of overstressing, such as cracking of the lining, are typically limited to the initial lining. However, special cases in swelling and squeezing ground require different approaches, including yielding support systems."

Jan 1, 2016

By J. A. Lombardi

"EXECUTIVE SUMMARY The use of membranes for the treatment of Acid-Mine-Drainage (AMD) water has been a 35 year mining industry quest that has only recently produced commercial scale Zero-Liquid-Discharge (ZLD) plants. The process of development of the membrane treatment of AMD has been defined by the water treatment industry’s efforts to control gypsum scaling of the membranes, an artifact of the concentration of calcium and sulfate ions on the concentrate or “brine” side of the membranes. Improved anti-scalants, changes to membrane surface geometry and a lowered permeate flux rate were all part of solving the calcium sulfate (gypsum) scale formation problem. Whether used singly or as part of a multi-stage membrane treatment process, the production of “left over” membrane concentrate or brine, in any volume large or small, was a second barrier to adoption of the method by the mining industry. The two identified “final brine” treatments were a) solar evaporation ponds and b) mechanical evaporators. Brine disposal by solar means is typically site limited to flat terrains or high net evaporation locations. Mechanical evaporation-crystallization is applicable at all sites but, typically, at onerously high ownership and operating costs. Miwatek, a South African water treatment start-up, has entered the mining AMD ZLD marketplace with two new, pilot-scale tested, processes, both of which are predicated on the innovative treatment of a reasonably concentrated AMD and neither of which produces a final brine that requires disposal. In the Miwatek Brine Treatment, MBT, method the membrane brine is caustic pH adjusted and de-calcified precedent to passage through a second membrane plant. The caustic is generated on-site by a lime treatment of the second-membrane concentrate. The first- and second-stage permeates are blended for discharge. The process usually yields no “final brine” for disposal. In the Miwatek Ettringite Treatment, MET, method a low pH first-stage membrane brine is lime treated in two or three steps in the presence of aluminum in a way that metal hydroxide and calcium sulfate solids are formed and purged from the system. Sufficient aluminum is often present in the feed water to, with judicious recycling, enable operation of the lime-aluminum treatment without the purchase of outside aluminum reagent. The first-stage membrane permeate is blended with the lime-aluminum treated membrane concentrate for discharge. The indications are that the method can comfortably meet the low 250 -500 ppm SO4 discharge water quality standards that have most recently been proposed in South America. The process yields no “final brine” that requires disposal. Projected own-operate costs for the MBT and MET systems are less than the estimated costs for all identified alternative treatments."

Jan 1, 2015

By M. Deutsch, E. González, M. Williams

"There is uncertainty in ultimate pit limits due to geologic variation and unpredictable economic landscapes. In this work we show how this uncertainty affects the ultimate pit and how it can be analyzed to improve the mine planning process. A stochastic framework using geostatistical simulation and parametric analysis is used to model the effects of geologic and economic variation on ultimate pit limits and overall project economics. This analysis is made possible by a new, highly efficient pit optimization implementation which can be automated and set up to calculate ultimate pits for hundreds of different scenarios in a matter of hours. Quantifying ultimate pit uncertainty early in the mine planning process allows mining engineers to make informed decisions regarding infrastructure placement, and to mitigate the possibility of incurring substantial costs relocating critical mine facilities. INTRODUCTION The mining industry is increasingly concerned with the effects of risk and uncertainty. Uncertain prices, unpredictable global markets, and unknown foreign exchange rates can alter the economic viability of a mining project in substantial ways. This economic uncertainty is compounded by geologic uncertainty. The extent and quality of any given deposit cannot be fully measured and is not known before consequential decisions must be made. These two sources of uncertainty are responsible for the majority of deviation between what happens during operation and what was initially planned. Understanding and explicitly quantifying this uncertainty will lead to better decision making and allow mining engineers and investors to be aware of what may occur. It is unrealistic to believe that one model, estimated from sparse measurements, is enough to capture both geologic and economic uncertainty and allow for optimal decisions. The entire breadth of uncertainty should be considered, as both upside and downside risks have large impacts on the investment potential and operational efficiency of mining projects. The workflow presented here uses Monte Carlo simulation and parametric analysis together to explicitly analyze the breadth of geologic and economic uncertainty as it applies to ultimate pit calculation and long range mine planning."

Jan 1, 2015

Electronic detonators have been in commercial use for a decade, with an excellent safety record. This paper lists known incidents involving electronic detonators. Typical standards required by regulatory bodies for static electricity and electromagnetic fields are reviewed. The performance of some detonators is compared to these standards; in general the minimum standards are easily exceeded. The general resistance of electronic detonators to extraneous electrical energy that can be derived from the body of test results is compared to danger levels for exposure of humans to these energies; it is shown that electronic detonators can safely tolerate higher electrical energies than people can. This comparison includes comparable data for electric detonators, which are shown to be more vulnerable to extraneous electrical energy than people are. Electronic detonators also bring significant safety benefits in blasting due to their testability, two-way communications, reliability, programmability and precision. The links between these attributes and enhanced safety are discussed with examples from actual blasting. Although electronic detonators are usually more vulnerable to extraneous electricity than non-electric initiation systems, the paper shows that the net safety benefit in handling and blasting is in favor of electronic detonators, which are the safest initiation system that has ever been offered to the mining industry.

Jan 1, 2010

Ferric (Fe3+) ions are omnipresent in flotation circuits. Depending on pH and the nature of the ore body, Fe3+ ions may play a role in the adsorption of thiol collectors on sulfide minerals. To investigate this possibility, a two-compartment galvanic coupling cell was designed. This cell was used to monitor changes in contact angle of a sulfide mineral in one compartment, while varying concentrations of the Fe3+ ions in the other. The results showed that Fe3+ ions promote xanthate adsorption as indicated by the increase in contact angle. Implications of this finding in sulfide mineral flotation in general will be discussed.

Jan 1, 1998

By J. Herhold, S. Plaum

"Current and future operational processes in the mining and underground construction sector are under the influence of the prevalent competition and the acute necessity of optimization approaches concerning corporate and project processes. Besides general construction procedures, especially underground construction procedures and procedures in the field of deep shaft construction are high-profile. Those processes describe high technical challenges as well as increased requirements to occupational safety and health. Therefor an occupational safety management, which should be adjustable to the company itself and adaptable to all kinds of projects, shall be created. The creation of such an occupational safety management would lead to an economically optimized and safe (within the scope of OSH law) implementation of internal activities for the performance of construction services underground and in the field of deep shaft construction. With this approach the satisfaction of the high safety request as well as the demand for process optimization, as part of keeping the own competitiveness, will be satisfied successfully at once. PROJECT BACKGROUND Introduction The health and safety protection as well as occupational safety look back on a long historical development, which had brought more important sectors and developments during the last years, not only in Germany but also on the European and international level. The accident insurance protected by law has already been reported in 1884, which is astonishing early. The launch time point is strongly connected with the on-going economic development in the end of the 18th century, but above all this increased in the 19th century. The progress of occupational safety and especially the interest in the integration and the concentrated consideration of occupational safety and the health and safety protection in the company process is strongly visible during the 19th century and directly connected to the industrial revolution. [9] The industrial revolution and with that the development of work places lead to changing demands in the field occupational safety and health and safety protection. Insufficient security precautions caused problems in the industrial revolution, such as personnel and material losses as well as serious injuries and their consequences. These and the fundamental economic endeavours of the entrepreneurs lead therefore to the important step to develop an occupational safety system. [9] The prevailing basic ideas seize the insufficient security precaution of work places as well as the economical and profitable ideas of the entrepreneurs and bring them together. From this the necessary entrepreneur’s task comes into being and that is bringing the work conditions to the way that life and health of employees are not in danger. [9]"

Jan 1, 2017

By John M. Hird

Texas Gulf Sulphur Company's Lee Creek Mine has opened a major phosphate mining district in the Central Coastal Plains of North Carolina (Fig. 1). The ore deposit as it is now known was roughly outlined in 1961 by a Texas Gulf geologist using wire line exploration methods. Slightly uraniferous phosphate materials were detected by a slim-hole gamma ray probe run in numerous farmers' water wells penetrating the formations. A follow-up-core drilling pro- gram determined the economic ore limits to lie in the south central section of Beaufort County beneath 70 feet to 120 feet of unconsolidated sediments. The 50,000 acre deposit is known to contain over two billion tons of phosphate ore amenable to strip mining methods. A part of the deposit underlies several thousand acres of the Pamlico River estuary. The 90 million dollar capital investment plant built by Texas Gulf during 1965-66 included a strip mining operation using a 72-yard walking dragline, a three million product ton per year flotation concentrator, four fluid bed calciners, a sulphuric acid plant (acid for captive use), a phosphoric acid plant, and three solid fertilizer material plants. Shipment to domestic markets is by rail and truck and to over- seas markets by barge to a transshipment terminal at Morehead City, North Carolina. Early mining investigations were conclusive first that the phosphate ore could economically be recovered only by dry strip mining methods, and second that artesian ground waters in the formation (Castle Hayne limestone) underlying the ore would have to be controlled. This report will relate the application of ground water hydrology in depressurizing the Castle Hayne aquifer to facilitate dry strip mining at depths 130 feet below sea level at the Lee Creek Mine.

Jan 1, 1970

By P. J. Cook

Comminution is one of the fundamentals of mineral processing, requiring large expenditures to be made on capital equipment, installation, power and maintenance. The trend toward lower grades and higher operating costs, mean mining operations are becoming increasingly marginal. The challenge is to improve and more importantly, utilize crushing and milling technologies that provide for reduced capital and operating costs whilst providing increased unit efficiencies. The Svedala Barmac Autogenous Crushing Mill presents such an opportunity by providing many of the cost savings and production increases required by its ability to produce a finer mill feed size and realize reduced energy consumption. This paper briefly describes the operation of the Svedala Barmac Autogenous Crushing Mill and reviews its benefits towards improving the efficiency of crushing and milling operations.

Jan 1, 1999

By Jerry C. Tien

China?s remarkable levels of economic growth during the past three decades have lifted almost 300 million people out of poverty. This amazing achievement has placed an increasing demand on energy and minerals, especially coal, which supplies 68.7 percent of China?s energy (June 2011). It is estimated that China mined more than 3 Gt (3.3 billion st) of coal in 2010, three times as much when compared to merely 10 years earlier. Such an impressive achievement does not come without major costs ?? including concerns with mine safety and an increasing number of occupational illnesses due to fast growth. This article reports on one of the major safety concerns in China?s coal mining, dust and dust control practices, and known cases of caol worker?s pneumoconiosis affiliated with prolonged exposure to excessive coal dusts. The exact size of China?s mining industry is not known, but it is estimated the coal industry is at least five-million people strong, and the metal and nonmetals industry probably employs another three million people. To meet increasing energy demand, China mined more than 3.1 Gt (3.4 billion st) of coal in 2010 from its 15,000 plus coal operations1, most of which are small- to medium-sized operations with annual coal productions ranging from a few thousand tons to 300 kt (330,000 st). These small coal operations are typically in remote areas, inadequately engineered, poorly ventilated and still using rudimentary drilling and blasting mining methods employing antiquated mining equipment and, presenting safety concerns, i.e., methane and dust explosions.

Jan 1, 2011

By Simon Strong, Tim Brown, Luis Ignacio Sanz Vivanco

"One of the most significant technical and practical challenges facing the tunnel construction team on the Legacy Way road tunnel project in Brisbane, Australia was how to erect the pre-stressed precast concrete slabs to form the smoke duct in the tunnel boring machine (TBM) tunnels. An essential part of the tunnel ventilation system, the smoke duct, extends the full length of the 4.6km long twin, two lane tunnels. The vast majority of the tunnels (approx. 4.3km) were constructed using two 12.4m diameter double shield TBMs. The refurbished Herrenknecht machines broke several world records on the way to completing the tunnel excavation works in just over nine months. With the excavation complete the focus turned to solving the complex civil tunnel fit out challenges. A key component of the civil fit out of the tunnels was constructing the smoke duct in the TBM tunnels which was designed as a precast solution. The slabs which each measure 8.62m long by 2.0m wide by 200mm thick and weigh close to 9 tonne need to be erected above cast in situ corbels whilst other tunnel finishing works continue. The space proofing clearance offered by the design to the support corbels below and the precast segmental lining above was in the order of only 100mm. This paper details the events of how the Transcity JV tunnel fit out team, comprising some of Europe and Australia’s leading tunnel construction specialists, drew upon the global strengths of the existing JV member companies and the global reach of leading TBM manufacturer Herrenknecht to develop an innovative system to solve this challenging problem. This globetrotting story, which starts in Australia, visits Europe and mainland China before returning to Brisbane where it all began."

Jan 1, 2016

Water and wind erosion of toxic zinc and lead smelter waste is one of the most urgent environmental problems to be solved in the Silesia region of Poland. Over 87 x 106 Mg of various mining wastes were disposed of in uncontrolled piles leading to soil, water, and air pollution in highly populated areas. Welz and Doerschel process Pb/Zn smelter wastes were stabilized in the summer of 1994 by application of heavy loads of CaCO3 (30 Mg/ha), CaO (1.5 -15 Mg/ha), and municipal biosolids (150 -300 Mg/ha), followed by seeding with a mixture of acid-and salt-tolerant grass species selected in a pot experiment. Vegetation was successfully established on 85% of the Welz material demonstration plot area (0.5 ha), even though it was initially high in water-soluble Zn, Pb, and Cd ranging from 0.4 to 1311,0.1 to 5.8, and 0.05 to 55 mg/kg, respectively. Standing biomass averaged 3.3 Mg/ha on the stabilized Welz waste zone by the end of the third growing season (1997). The revegetation of much of the Doerschel material area failed initially because of extremely high salinity (16 dS m-1), high content of water soluble metals (Cd in particular), and heavy compaction. The area was capped (15 cm) with waste lime and retreated with bio-solids (300 Mg/ha) in 1995, and standing biomass averaged 2.9 Mg/ha in the fall of 1997. The observed plant response to bio-solids and lime indicates this approach to be an environmentally beneficial technology as compared to the traditional methods utilizing topsoil covers.

Jan 1, 1999

The Kinross DeLamar Mine has been operated for more than 17 years producing precious metals dore' from ores, principally silver bearing with associated gold co-products. In late 1995 a new orebody was commissioned, the Stone Cabin orebody, and the site began a phased shift from silver dominance to gold dominance in terms of precious metals revenue. The Knelson Concentrator was selected to remove gold from a portion of the cyclone underflow stream in the grinding circuit. This paper describes the development of the flow sheet, specific mineralogical impacts on Knelson product and downstream materials, and impacts on mine/mill grade reconciliation.

Jan 1, 1997