Search Documents

By Walter E. Lewis

A mothod of cutting St. Poter sandstono by streams of water under pressuro from nozzles and pumping the resulting, sand to the surface has roduced the cost of storm-sowor construction in the Minneapolis-St. Paul aroa. The hydraulic tunneling method, has boon in uso since 1934, and it is adaptable only to the lower part of tho St. Potor, sandstone, which lios within or just abovo the ground-wator levol. Tho upper part of the formation, immediately bolow tho Plattoville limestone, 18 comonted and camot bo mined by hydraulic mothods. The tunnel oporation observed in this instance is a main storm sowor starting at tho Mississippi Rivor below the 10th Avenuo SE bridge and will be drivon 6,000 foot at a grado of 1 foot por thousand undor the city of Minneapolis to Konnody and Arthur Stroots NE. A lateral storm sowor, which branchos from the main sovor at 8th Street SE, will oxtond from 10th Avonuo SE to 15th Avonuc SE. Tho tunnele are being drivon with the floor approximately at ground-wator lovol. All waters ontoring the main storm sower vill drain into the Mississippi Rivor. Tho main storm sewer cross soction is excavated to a roughly hox- agonal shapo 10 foot high by 10 foot wido at the contor. The upper half of the tunnol soction is solidly lined with either timber or stool. After all oxcavation is completed, the tunnel will be finished with a concrete circular lining 8 feet in inside diameter. The lateral storm sewer is excavated to a 5-1/2-foot by 7-1/2-foot section and will event- ually be finished with concrete to a modified horseshoe-shaped section 6 feet by 4 feet. Where the back or walls are considered unsafe during excavation, the upper half of the tunnel is lined solidly with timber. The equipment used by the Sower Division, City of Minneapolis, has been selected to meet a number of applications in storm-sewer work with diversified usage in mind. The sand pumps used on this job are rubber-lined, designed to work against a head of 100 foet. Either 4-inch or 6-inch diameter suction and discharge openings may be used. Other equipment, such as pipe, mine rail, flexible hoses, compressors, and general surface shop equipment, is drawn from a contral warohouse. It may be either new or used, depending on what is available at the warehouse. Much of the pipe and mine rail has been used for many years on several different tunnol jobs.

Jul 1, 1950

By B. J. Moore

This publication contains analyses and related source data for 269 natural gas samples from wells and pipelines in 18 States. All of the samples were obtained and analyzed during, calendar year 1979 as a part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4862 and 576.3 The results of the investigation of the occurrences of helium are published annually to make the information available as soon as possible to the gas industry and the general public. Twenty-one previous publications have presented tine results of 11,883 gas analyses made prior to 1979. The first three, Bulletins 486,4 576,5 and 617,6 contain analyses and related source

Jan 1, 1980

By L. E. Cardwell

This publication contains routine analyses and related source data for 475 natural gas samples from 17 States and two foreign countries. Of this total, 454 samples were collected during calendar year 1971. The remaining 21 samples were collected during previous years, but releases granting permission to publish the analyses were not received until 1971. All samples were collected as part of a continuous survey of the free world for occurrences of helium in natural gas. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4 Thirteen previous publications have presented the results of 9,427 gas analyses prior to 1971. The first three, Bulletins 486,5 576,6 and 617,7 contain analyses and related source data on 5,218 gas samples collected from

Jan 1, 1972

By James E. Aplin

Previous studies have shown that fracturing of roof strata precedes ultimate failure, and that the fracture development causes an accompanying increase in the apparent resistivity of the strata. Using this principal, a microprocessor controlled resistivity roof fall warning system (RRFWS) was developed that automatically sequences through and records up to 32 electrodes that may serve as either voltage or current electrodes. This capability permits increased coverage with a minimal number of required electrodes. The data is stored in a nonvolatile memory and on an optional printout, making the system nonsusceptible to loss of mine-power. To further save battery power, the system's electronics shut down between readings, except for a carbon molybdenum steel real-time clock. At a preprogramed interval, the RRFWS reactivates and repeats the sequence. If the absolute change or the rate of change of resistivity exceeds a predetermined limit the system is capable of sounding an alarm. In addition to the monitor, a stainless steel mod led split-set electrode was also developed that permits long-term corrosion-free contact.

Jan 1, 1983

By Charles L. Kusik

A study was conducted for the Bureau of Mines, U.S. Department of the Interior, to provide information which will lead to an increase in the recycling of mineral materials, in order to help conserve the Nation's mineral resources. Data were collected on energy requirements to recycle prompt industrial and obsolete scrap for nine metal commodities: Iron and steel, aluminum, copper, zinc, lead, stainless steel, titanium, tin, and nickel and nickel alloys. Major process routes for recycling were considered, starting from the first collection point through scrap preparation, transportation, smelting and/or refining to the molten metal, ingot, or other semi- finished form approximately equivalent to a primary metal of a similar composition. Available data for 1976 were collected on the amounts of each metal commodity recycled by major scrap categories. In addition, energy requirements were estimated for separating municipal solid wastes into four major categories: Refuse-derived fuel, and magnetic, aluminum, and glass cullet fractions. Finally, areas of research were identified to enhance recycling and/or increase the efficiency of energy use.

Jan 1, 1978

By Edwin A. Clarke

[For almost 2 decades the Bureau of Mines has been Interested in converting solid fuels to liquid fuels. Small-scale laboratory investigations were carried on for a number of years.4/ This work wad expanded substantially under authority of Public Law 290, approved by the 78th Congress on May 5, 1945. As part of the. broadened program, coal-hydrogenation demonstration plant was designed and erected at Louisiana, Mo., where: hydrogen-manufacturing and compression equipment, shoes, electric power, and other utilities and facilities were available from a discontinued wartime ammonia works . The plant uses the direct -hydrogenation or Bergius process, but the process differs from prewar European practices in many respects. Many noteworthy improvements h eve bean made, particularly by substituting automatic instruments for manual control of process variable's, in line with modern American processing practices. The over-all objective of the demonstration plant is to bridge the gap between laboratory end commercial-scale operation by furnishing cost and engineering data to develop a synthetic liquid-fuels industry when it proves technically and economically justified. Fitting into the over-all program, specific objectives o early runs were to (1) train personnel who had no experience with this type of operation, (2) break in the installed equipment, (3) obtain successfully integrated operation of the entire plant, and (4) work towards obtaining data on the hydrogenation of coal-tar oil and a typical low-ash coal. In beginning fan integrated operation, it is common practice to operate and obtain reaonably smooth performance of each unit before the over-all operation is undertaken. The first part of the plant completed was the refinery, consisting of several fractionating systems, a stabilizer, and a chemical treater.]

Jan 1, 1953

By Jr. Gabler

Methods for the direct spectrochemical determination of impurities at the parts-per-million level in tungsten metal and oxide are presented. Several published procedures were investigated and numerous modifications were made in establishing procedures with improved precision and extended lower levels of determinability. Details of standards preparation are presented, experimental work is described, and three preferred methods are described in detail. A germanium carrier-distillation procedure is applicable to the determination of 13 elements in tungsten powder; a silver chloride carrier-distillation procedure provides for the determination of 24 elements in tungstic oxide, and a sustaining ac arc method is applicable to 26 elements in tungstic oxide. The choice of methods to be used depends upon sample form, elements and concentrations to be determined, and the precision and accuracy required. The investigations reported here were undertaken to develop direct spec-trochemical methods with increased accuracy and precision to determine impurities in high-purity tungsten and tungstic oxide, to define the lower concentration levels of detectability and measurement for the common impurities in tungsten by direct spectrographic means, and to present the details of the developed or modified methods that have proved applicable.

Jan 1, 1965

By H. W. Sohns

A retort was constructed in which fine particles of shale, entrained in steam or other gaseous media, could be retorted at controlled temperatures and residence times and the effects of retorting variables upon quality and quantity of products could be determined. Studies of the effects of temperature upon products obtained from Green River (Piceance Creek Basin, Colo.) and Chattanooga (Tenn.) oil shales were completed. The feasibility of using the retort to process a shale of extremely high moisture content from Brazil also was investigated. Air was used as the entraining medium in a series of studies in which combustion of some of the products of retorting within the retort tube supplied a major portion of the process heat. In another series, shale oil from a conventional retort was cracked thermally to obtain data for comparison with results of retorting en-trained shale. In still another series the effects of rates of steam flow and solids feed upon rates of heat transfer from the furnace to the process stream were studied. Crushed quartz rather than oil shale was charged to the retort in this series. A study was begun in which raw shale was partly retorted, the products separated, and the partially retorted shale recharged to the retort. The shale was to have been recycled until it was completely retorted in an effort to improve oil yield by recycle retorting; however, the project was terminated before the investigation was completed.

Jan 1, 1959

By John R. McWilliams

This is one of a series of reports being published by the Bureau of Mines on mining methods and costs at various mines throughout the United States. Including the Holden mine in this series is particularly appropriate at this time. The mine was operated on a low-cost, large-scale production basis to compensate for low-grade ore. Even with the best conditions and the most efficient methods, the margin of profit was small. Under the present situation of rising costs and lowering metal prices, the profit margin vanished. On June 28, 1957, the mine operations ceased; therefore, this report can review the entire life span of the mine.

Jan 1, 1958

These tentative inspection standards have been prepared as a guide for the Federal inspection of the anthracite mines of the United States. The Federal Coal Mine Inspection Division is not a mining-law-enforcement

Jan 1, 1943

By G. E. Johnson

Batch tests of coals and coal-derived materials were made by the Bureau of Mines to determine their effectiveness in removing organic contaminants (COD or chemical oxygen demand, comprising those organic compounds that can be chemically oxidized, and ABS or alkylbenzene sulfonate, common household detergents) from the final effluent of secondary-treated waste waters. The adsorptive capacities of flyashes, coals, including at least one sample of each rank found in this country, pretreated coals, and miscellaneous materials including commercial chars and coke, were determined and compared with that of granular activated carbon. The coals, though not as effective as activated carbon, possess an economic advantage--they are relatively inexpensive, and they can still be burned as fuel without any loss of fuel value after use in waste¬water treatment. A hvcb coal was found to be one of the best, having about one-fourth the capacity of activated carbon for COD, adsorbing about 4 percent of its weight before it became saturated. Several coals contained constituents that added to the COD content of the treated water. Thus knowledge of the performance of the coal is necessary to insure selection of a proper coal as adsorbent.

Jan 1, 1966

By Frank A. Peters

With the current renewed interest in advancing the technology for producing alumina from domestic raw materials, revisions of previous cost estimates to provide planning data are urgently needed. Completely new cost estimates on a 1973 basis are included for four alumina-from-clay processes and one alumina-from-anorthosite process. These estimates are based on new or previously calculated material balances, recalculated heat requirements, and new equipment designs. The use of larger and more modern equipment has permitted a significant reduction in labor requirements as well as equipment costs. Chemical prices, labor rates, and utility rates typical of late 1973 are used in these cost estimates. In addition to the revised cost estimates, all 21 previously published alumina evaluations compiled by the Bureau of Mines were updated to show the effect of inflation using an inflation index and late 1973 chemical prices, labor rates, and utility rates.

Jan 1, 1974

By A. Matzick

In its work under the Synthetic Liquid Fuels Program the Bureau of Mines has developed on a 6-ton-a-day-pilot-plant scale a continuous, gravity-feed retort far distilling oil from oil shale. The development work covered by this report was done from January 27, 1950, to January 26, 1952, at the ail-Shale Experiment Station near Rifle, Colo. Over 300 pilot-plant tests were made during the investigation. The basic retort developed has been named the Gas-Combustion retort. In this process, part of the heat for retorting of the shale is generated by burning recycled product gas in a combustion zone within the descending shale bad in the retort. Additional heat is supplied by combustion of the carbonaceous residue remaining in the spent shale after the oil has been distilled. Air for combustion is admitted through an air distributor in the center of the bed at about the mid-point of the retort. Hot gas rising from the combustion zone heats countercurrently the descending raw shale and liberated shale oil by pyrolysis of the shale. After passing through and exchanging heat with the incoming raw shale, the oil is condensed as a fog or mist in the gas, which is withdrawn at the tip of the retort. The cool gas is then piped to an oil-recovery system where the oil is separated from the gas in centrifugal separators or other types of mechanical or electrostatic separators. The hot, spent shale below the combustion zone is cooled by heat exchange with recycle gas, which is a portion of the effluent gas from the oil-recovery system.

Jan 1, 1955

By R. A. Cattell

Continuing progress in a petroleum and natural gas research program of world-wide significance makes it difficult to pinpoint accomplishments within definite time limits, and it is helpful to look back as well as forward in attempting to introduce and summarize the petroleum work of the Bureau of Mines in the fiscal year 1953. The 1952 report2 / indicated progress in a long-range program applicable in large part to both defense and peacetime requirements. The present report indicates a continuation of that program, modified partly by new demands and interests of government and industry, and is highlighted by a number of significant contributions to the knowledge of petroleum and natural gas and their production and utilization. The intent of the program was clearly epitomized in a statement made near the end of the fiscal year at a general conference of Bureau of Mines personnel where the record was critically reviewed:

Jan 1, 1955

By CLARENCE G. SMITH

Prior to the actual development of an oil property it is difficult to determine the quantity of oil under the property and the rate at which this oil can be brought to the surface-factors that determine the ultimate value of the property. Consequently, there has been much confusion in devising accounting systems that, during the entire life of a property, will show costs and profits from which the producer can determine whether his property is being worked at a profit or otherwise. The Bureau of Mines publishes this report in recognition of a distinct need for a simple treatise on accounting methods adapted to the peculiarities of the petroleum industry. Probably many companies operating oil wells are not fully acquainted with details important to the welfare of their business, because their account books fail to furnish them with exact and adequate data. With the accountant rests the responsibility of providing the management with reports setting forth the details of the business expressed in fitting terms as well as in dollars and cents. These reports are a means whereby efficiency may be maintained, waste prevented, oil obtained and sold, and money suitably reinvested. They also enable a concern to study the progress of its business in order to conserve to the utmost the possible benefits from an exhaustible deposit of mineral wealth. When managements realize the extent of the waste at their properties more attention will be given to the character of the accountancy records. Herein are presented descriptions and discussions of balance sheets, profit-and-loss statements, and bookkeeping methods peculiarly adapted to the oil business. As far as possible, technical phrases have been omitted in order that those not familiar with accounting terms may be able to follow the subject matter. The systems of keeping books outlined in Chapter X have all been found practical. For brevity as well as clearness the major part of the work refers to the company operating only one property.

Jan 1, 1917

By GEORGE S. POPE

This bulletin is the third of a series a showing the results of ment purchases of coal according to specifications as to its quality and giving typical forms of proposals for supplying coal and general information relating to government coal purchases . Numerous calls for authentic information concerning the purchase of coal according to its heat value attest a growing interest in the subject. Many of the commodities of life have long been purchased according to specifications requiring chemical or physical tests , or both, to determine whether the material delivered meets the requirements , the price to be paid depending on the results of the tests . Until recent years coal consumers purchased coal merely on the statement of the dealer as to its quality , relying on his integrity and on the reputation of the mine or district from which the coal was obtained. It is surprising that the important question whether value was being received for the money expended was not sooner seriously considered . The purchase of coal by specification is an important step toward the conservation of our national mineral resources , for it results in an increased use of the lower grades of coal. The poorer coals find a market by competing with the better grades , not as to the price per ton but as to the cost of an equal number of heat units. This paper gives in detail the results of government purchases of coal for the fiscal year 1908–9 and the list of contracts with abstracts of specifications for the fiscal year 1909–10 , and summarizes the information on this subject obtained by the Survey. It is hoped that this information will promote a better understanding of the specification method of purchasing coal and furnish data valuable alike to coal dealers and coal consumers , so that equitable contracts can be more readily made.

Jan 1, 1910

Seventy-three of the 90 naturally occurring elements that are found in the earth's crust are metals or metalloids. The quantities of metals used annually in the United States range from about 100 million metric tons (steel) to a few kilograms (osmium). The recovery of metals from discarded products or industrial process wastes, especially those metals that are used in large quantity, are very expensive, or are unusually toxic, is important to the national economy and to the natural environment. From its inception in 1910, the U.S. Bureau of Mines (USBM) has been the Government's prime source of information on metals recycling, as well as a major innovator in recycling technology. Statistical data on scrap generation and processing have been summarized annually for many years in the USBM's Minerals Yearbook. Most of the data for individual metals discussed in this report were extracted from that publication.

Jan 1, 1993

By John C. Holtz

"The Federal Bureau of Mines serves the mining industry by approving equipment that is designed to prevent explosion, fire, shock, or toxic hazards in mines when such equipment is used and maintained in a proper manner, through research, consultation, testing, and inspection, the Bureau studies machinery and component parts submitted by manufacturers and others. Before receiving the Bureau's approval as permissible for safe use in mines, equipment must pass exacting tests and must meet strict requirements established through research and experience and listed in the Bureau's various permissibility schedules. An important phase of the Bureau's research is the testing of diesel engines.Mobile diesel-powered equipment can be used safely in underground noncoal mines and tunnels when mechanical ventilation is provided to dilute and remove the exhaust gas and to replenish oxygen in the underground atmosphere. Safe ventilation is determined by suitable tests of each engine used in a diesel machine. This ventilation cannot be predicted safely, accurately, and economically from any general empirical relationship.In determining safe ventilation, the quantities of carbon dioxide, carbon monoxide, and oxides of nitrogen generated by a diesel engine must be ascertained. These quantities are related to the displacement of the engine, its speed of operation, the design of the combustion chamber, and the fuel:air ratio needed to produce useful power. At overrich fuel:air ratios, all diesel engines generate excessive quantities of toxic carbon monoxide and smoke. The results of engine tests are used to determine a maximum fuel-injection rate at or below which carbon monoxide can be controlled by a reasonable ventilation and smoke is essentially eliminated. Toxic oxides of nitrogen are related to fuel:air ratio and the design of the combustion chamber. Their concentration in the exhaust cannot be controlled by engine adjustments, and each engine appears to have individual characteristics concerning formation of these oxides. Production of oxides of nitrogen frequently is the most important factor in determining safe ventilation."

Oct 1, 1959

By John B. Ivey

This is a geologic study of the U.S. Bureau of Mines Oil Shale Tract in the Piceance Creek Basin of Rio Blanco County, Colorado for the preparation of a set of detailed surface geologic maps, measurement and identification of joint attitudes and frequencies, and the classification and mapping of the soils of the area.

Jan 1, 1978

By J. W. Thompson

RAILROAD GRANT-MDIERALS. Diatomaceous or infusorial earth when found in such quantity and quality as to render lands containing deposits valuable therefor are mineral lands within the meaning of the mining laws and must be excepted from grants to the Central Pacific Railway Company. Central Pacific Ry. Co., In re, 45 Land Decisions, 223, p. 226. RAILROAD GRANT-CLASSIFICATION, If any evidence of minerals is found upon lands within a railroad grant and the showing is sufficient in the opinion of prudent and qualified persons to warrant further exploration and expenditure, with reasonable prospects of success, then the land can not be classified as nonmineral and is not subject to the grant to a railroad company. But where there is no present indication of minerals nor any geological evidence upon which to base a mineral finding, land should not be classified as mineral, or held for further classification and reserved from the railroad's grant, upon the surmise that future prospects might disclose evidences of minerals. Southern PacUl.c Ry. Co., In re, 45 Land Decisions, 326, p. 329. INDEMNITY SELECTION BY RAILWAY COMPANY, Under section 3 of the act of July 2, 1864 (13 Stat., 365), and the joint resolution of May 31, 1870 (16 Stat., 378), the Northern Pacific Railway Company could take coal and iron land within its primary or grant limits. It could not base an indemnity selection upon the claim that certain land was coal or iron in ;;haracter, as such land was not lost to it as part of the grant. But the company was authorized to select other lands in lieu of those lost because of their mineral character, but the word "mineral" did not include iron or coal, and, accordingly, the railroad company was entitled to take coal lands under its indemnity selection.

Jan 1, 1917