Search Documents

By Clark P. Mangelsdorf

The report consists of two parts. In Part I is a state-of the-act study of roof truss technology as of January 1979. Included are a history of the truss concept, a review of analysis techniques, a record of hardware available and equipment used in its installation and numerous examples of user experience. Part II is concerned with a study of the role of friction in the behavior of a roof truss. The appendices include laboratory tests by the author.

Jan 1, 1979

By Albert W. Deurbrouck

Twelve samples from six Barbour County coal beds were analyzed for this report. The samples collected were generally high sulfur content coals, frequently exceeding 3 percent in the raw-coal sample. Many of them could not be upgraded to acceptable metallurgical standards even by rigorous preparation procedures. The production of coal in the county in 1963 amounted to almost 3 million tons of which 44 percent was mechanically cleaned.

Jan 1, 1965

By Raghoottma S. Pandurangi, Mohindar S. Seehra, Pedro Bolsait, Bronwyn L. Razzaboni

"Surface IR (infrared) modes of crystalline and fumed (amorphous) silica particles, calcined at temperatures up to 1095°C, have been studied by Fourier transform infrared spectroscopy. The ability of these same particles to lyse cells has been measured by a hemolysis protocol. The untreated crystalline and amorphous materials differ by a factor of 40 in specific surface area, and the intensity per unit mass of the sharp surface silanol band near 3745 cm-1 in the amorphous material is an order of magnitude larger than in the crystalline material. A similar difference is observed in the lysing potential of the two materials. The intensity of the silanol band increases after calcination for both materials, reaching peak values near 500°C, followed by a dramatic drop at higher calcination temperatures, and reaching negligible values for materials calcined near 1100°C. The lysing potential data follow essentially the same pattern for both crystalline and fumed silica. These results are consistent with the hypothesis that the surface silanol groups are involved in cell lysis. Further experiments are suggested to evaluate the relationship between the surface structure of ailica particles and their potential cytotoxicity. IntroductionThe characterization of the surface structure of various allotropic forms of silica is of interest because the cytotoxicity of silica particles of respirable size has been commonly related to the chemical interaction of functional groups on the surface of such particles with the lipoproteins contained in cell membranes (1-3). It has been found that the cytotoxic potential of silica particles varies greatly with their crystalline structure (4,5), particle size (6-8), surface composition (9), and molecular surface configuration (1,10). Studies of the infrared (IR) modes of various forms of silica have been reported by a number of researchers (3 ,11-19). Several books and reviews (20-24) have dealt with the identification of functional groups on silica surfaces and the effect of heat treatment on the surface structure. The nature of the surface is said to be critical in determining the biological activity of silica dusts (3).Fourier transform infrared (FTIR) spectroscopy is a highly sensitive ·technique for identifying IR surface modes of tine particulates, and it was deemed of interest to examine the surface structure and its relation to lysing potential of two widely different types of respirable silica dust. The lysing potential of respirable dust particles has been considered a first-level test for potential cytotoxicity."

Jan 1, 1990

By C. W. Davis

This report follows the same general scheme as did its predecessors; it begins with a dissertation on some phase of ore-testing, continues with results of investigations of ore-treatment methods and of metallurgically important analytical processes, and concludes with an exposition of tests made by established methods on typical ores selected as representative of certain mining districts. One of the first things that is done after an ore has been received is to look at it under the microscope. Microscopic examination serves as an important complement to chemical analysis in interpreting the percentage composition in terms of minerals. If it has been found difficult to treat an ore, the reasons for this action and indicated methods to overcome the difficulties may be ascertained by testing with a microscope. For example, failures in selective flotation have been traced to intimate mineral association and changes in mineral surfaces through incipient oxidation. The importance of surface stains or tarnishes and the presence of adhering slime particles have been found to be responsible for the difficulty experienced in the treatment of certain gold ores.

Jan 1, 1938

By C. W. Davis

This report follows the same general scheme as did its predecessors; it begins with a dissertation on some phase of ore-testing, continues with results of investigations of ore-treatment methods and of metallurgically important analytical processes, and concludes with an exposition of tests made by established methods on typical ores selected as representative of certain mining districts. One of the first things that is done after an ore has been received is to look at it under the microscope. Microscopic examination serves as an important complement to chemical analysis in interpreting the percentage composition in terms of minerals. If it has been found difficult to treat an ore, the reasons for this action and indicated methods to overcome the difficulties may be ascertainedd by testing with a microscope. For example, failures in selective flotation have been traced to intimate mineral association and changes in mineral surfaces through incipient oxidation. The importance of surface stains or tarnishes and the presence of adhering slime particles have been found to be responsible for the difficulty experienced in the treatment of certain gold ores.

Jan 1, 1938

By Lloyd Williams, R. E. Hershey, B. W. Gandrud

"1. The investigation shows that the Sewanee bed is the only bed of major importance in Marion County, 97 percent of the coal mined in the county having come :from this bed. There are coal reserves in minor quantity in the Battle Creek bed, and production from this bed depends on a few small truck mines. The Richland bed, or Lower Sevanee has been mined in the past, but no coal has been produced from it in late years. There are no production records of any other beds in the county, although some coal has been produced from them.2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on l,800 tons per acre-foot of coal in place, are estimated to be 61 million short tons as of January 1, 1953. Of this total, 55 million short tons is in beds 28 inches and more thick. Areas in each bed ·were omitted from the estimate where available data relative to the bed characteristics are too meager to permit making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.3. Recoverable reserves of coal are estimated in beds 28 inches and more 'thick. This recovery is based on total thickness of coal in the bed (less partings 3/8-inch thick or more), rather than on the thickness of the coal actually mined. This thickness is about the minimum now being mined by hand loading onto conveyors in the Appalachian Region. The combined weighted average recovery for the Sewanee and Battle Creek beds in Marion County, as determined by this investigation, is 60.9 percent. Based on this, the recoverable reserves of coal in Marion County are estimated at 34 million tons."

Oct 1, 1955

By K. P. Wang

The foundation of Japan's growing industrial and economic strength lies primarily in minerals, power, and technical know-how. Domestic raw material resources cannot supply domestic demand, and imports are indispensable. The Japanese are forced to acquire minerals and metals on a global basis, and their activities already have made an impact on international markets. A by-product of these efforts is the development and expansion of mines in many parts of the world to supply Japanese requirements. Japan now has a surplus capacity to produce finished products for consumption and export. Tradition-ally, domestic deficits in minerals have been met by importing crude materials. Because of the rising demand, however, the time has come when semi finished products as well as crude minerals are required. While the domestic market is the mainstay for Japan's industrial products, expanding export markets are essential for balancing trade and for providing economic prosperity and higher living standards for the Japanese people. Japan has a long history of mineral and industrial development, and the best in modern practices abroad has been adopted and modified for use under Japanese conditions of smaller enterprises, cheaper labor, and a more closely knit society. Generations of industrious workmen, technicians, and business-men have been trained in industrial occupations. Devastation of war temporarily slowed progress, but at the same time provided the opportunity for reconstruction, modernization, rationalization, and expansion. The Japanese excel in small and medium-sized operations, but they also have mastered large-scale production. Management is aggressive, practical, and strongly imbued with the concepts of effective utilization of resources. Integrated operations, diversification of facilities, intense competition among concerns in the domestic market, and close cooperation in foreign activities characterize Japanese industrial policies. Available capital has been utilized up to the limit for the establishment of mineral and other industrial facilities at home and abroad. Technology, machinery and equipment, and transport services have been exported along with venture capital, and funds have been advanced against future delivery of foreign raw materials. The Government has been restrained in regulatory functions and has provided technical services to private industry. Thus, Japan's technological foundations are secure, management practices are efficient, and government has stimulated production. The future outlook is bright for the continued rapid growth of mineral and other industries in Japan. Already supreme in Asia in per capita output and living standards, Japan steadily is gaining on the European countries. Steel production has overtaken the United Kingdom and is pressing the level in West Germany. Consumption of fuels and power is expanding at a rapid rate. Construction activities are booming. Japan has built up medium-sized non-ferrous industries. Its ability to produce the exotic metals needed in the nuclear space age is well established. Since Japan makes a great variety of mineral products, her overall posture in mineral extraction and processing is strong. Primarily as a result of intensive efforts in the mineral and other industrial fields, Japan is emerging in world markets as a serious competitor to all industrialized nations.

Jan 1, 1962

By [F. P. ] Stambaugh

Results of research on the hydrothermal precipitation of zirconium oxide from the Bureau of Mines' zirconyl chloride-sulfate strip liquors indicate that nuclear grade material can be prepared by this process. Greater than 99% of the zirconium value can be precipitated at 250-260°C in short (5-10 minutes) reaction time without consumption of acid value of the liquor. Thus, precipitation of zirconium dioxide on a continuous basis, i.e., the zirconium dioxide is precipitated in a continuous mode of operation by pumping the strip liquor through a heated pressurized reactor and recycle of the acidic (spent) liquor to the process stage are favored. The results of accompanying studies of liquod/solid separation, product washing and dewatering, product purity, and chlorination of the product are presented and discussed.

Jan 1, 1980

By Bureau of Mines Staff

Coal research and related activities in 1964 by the Bureau of Mines resulted in many advances in the production, preparation, and utilization of this valuable natural resource. Mining research during the year was marked by work on hydraulic mining, coalbed degasification, mine drainage control, mine sealing, strip-mine rehabilitation, and quenching of mine-refuse fires. Bureau research continued to produce information leading to increased safety in underground mining. Such research included roof and rib control via bolting and bonding, pressure monitoring of coal and mine rock during mining operations, and development of safety devices for detecting conditions leading to roof falls. Other safety work was continued on methane detectors, coal-dust suppression, and mine venti lation equipment and techniques. Mine explosion and explosives research, mine equipment and materials, safety rule modernization, and safety education and training of mine workmen were continued. Coal storage and preparation work in 1964 ranged from freezeproofing of lignite for rail shipment, through washability studies of coals and washing equipment, to research on new ways to remove ash and sulfur from coal. Electric power production, which ,accounts for a major portion of the market for coal, received further study. Unique power generation systems, inc luding coal-burning gas turbine and megnetohydrodynamic generators, were intensively investigated. Conventional power systems were improved through continuation of work on furnace performance, powerplant stack gas purification, and engineering and boiler water service.

Jun 1, 1965

A significant amount of information regarding the crushed stone and sand and gravel industries in each State is available from State agencies and State trade associations. These organizations continuously monitor the State mineral industries and are therefore an important source of detailed information at the local level. This third edition of the directory was prepared to provide a listing of government agencies and trade associations that can assist the users interested in obtaining detailed listings of crushed stone and sand and gravel producers, in addition to the information published by the U.S. Bureau of Mines.

Jan 1, 1994

By F. E. Block

This investigation was made as part of a larger program to develop basically new methods for preparing yttrium metal in high-purity form. It was performed under a cooperative agreement between the U.S. Atomic Energy Commission (AEC) and the Federal Bureau of Mines. Laboratory-scale tests were made to devise methods for preparing high-purity, anhydrous yttrium trichloride, for reducing the yttrium trichloride with sodium or lithium, and for consolidating the resulting yttrium sponge into ingots.

Jan 1, 1960

By A. C. Burr

This progress report summarizes operating results on the gasification of natural lignite from five runs of the commercial-scale pilot plant at Grand Forks, N. Dak., during December 1946 and calendar years 1947 and 1948, when the plant was operated for 1,996 hours. A primary specific objective was to determine the useful life of the outer metal retort tube as it is influenced by corrosion and other factors under a wide range of operating conditions. A secondary objective was to develop the technology of production when generating gas with a high ratio of hydrogen to carbon monoxide in both the divided and continuous annuli. Results are summarized in graphs and tables that show hydrogen-carbon monoxide ratios from 2.3 to 9 at gas-production rates from 6 to 12 M cu. St. per hr. (thousand cubic feet per hour), or approximately 30 to 60 cu, ft. per square foot of heated retort-wall surface per hour. Gas yields ranged from 36 to 54 M cu, ft. per ton of natural lignite or 63 to 91 M cu. ft. per ton of moisture- and ash-free lignite, Production rates were higher in the divided annulus, but these represent the maximum capacity of the plant only at high hydrogen-carbon monoxide ratios when the high concentration of excess steam and low furnace temperature limit gas production. A ratio of 6 was the highest produced in the continuous annulus because mechanical Limitations of the auxiliary equipment prevented attainment of higher ratios. The lignite feed rate appears to influence the production rate more than any other individual operating variable. Heat balances for four periods when gas with ratios from 2.3 to 7.2 was produced with a lignite feed rate of about 325 pounds per hour suggest that the potential heat in the gas is lower at higher ratios, owing to increased heat losses in the excess steam. Heat-transfer rates through the retort tube in these four tests were between 1,500 and 3,000 B.t.u. per square foot per hour. These rates are much lower than those reached in many earlier tests, but no attempt was made to achieve maximum rates of heat transfer.

Jan 1, 1953

By Frank K. McIntosh

Bauxite was first discovered in Tennessee, at Chattanooga, in 1906, during the construction of' the McCallie Street tunnel through Missionary Ridge. Several years later, bauxite was found in sinking a well on the Perry or Isabella Stewart property. These and other deposits furnished a substantial tonnage for the abrasive and chemical industries during the years 1906 to, 1920. The search for domestic sources of war material prompted by World War II brought the Tennessee bauxite deposits to the attention of the Bureau of Mines. During the summer of 1942, James S. Cullison and E. Godwin, geologists of the United states Geological Survey, made a survey of the bauxite deposits of the area. In August 1942, Harold B. Ewoldt, a Bureau of Mines engineer, accompanied by the Geological Survey party visited the area and a drilling program was prepared. Drilling was started in November 1942 and continued until March 1943. A total of 2,519.5 feet in 38 holes was drilled on three properties.

Jan 1, 1949

By J. L. Shultz

The Bureau of Mines extended its investigation of methanation catalysts. The noble metals (platinum, palladium, ruthenium, rhodium, osmium) and rhenium), molybdenum, and tungsten were tested in hydrogenations of carbon monoxide and carbon dioxide at 21 atmospheres in a temperature range between 200° and 600° C. From the 8 metals studied) 25 catalysts represent 5 catalyst types were prepared and tested. The impregnated 0.5-percent-ruthenium catalyst proved to be the most active and versatile of all the catalysts produced. Tungsten and the noble metals other than ruthenium were low in activity and usually required temperatures above 500° C for appreciable production of hydrocarbons. Molybdenum was moderate in activity, but further improvement in molybdenum catalysts seems possible.

Jan 1, 1967

By R. Van A. Mills

Rapid deterioration and destruction of metal equipment in oil and gas fields cause waste of resources and financial losses that must be lessened or eliminated if operations in many important fields are to continue profitable. The magnitude of this destruction is proved by the huge consumption of iron and steel pipe, tubing, casing, pump valves, and sucker rods to replace worn-out equipment, and by the amount of such equipment that is left in wells or junked. (See PI. I, A and B, and PI. II, A and B, and Fig. 14, p. 61.) This destruction of equipment constitu~es in itself a serious waste, but contingent production troubles, such as underground leakage of oil through defective tubing and pumps, and the consequent loss of oil and gas because of damage to pay sands by infiltrating water and silt, frequent and costly repairs with necessary suspension of production, and the ultimate injury to or loss of valuable wells, often cancel all operating profits. Many of these troubles result from rapid destruction of metal equipment by corrosive waters. The strata penetrated by the wells usually contain saline waters. Certain types of these waters, with their associated gases, are intensely corrosive; they attack well casing or tubing so vigorously as to riddle it with holes, rendering it useless in a few years or even a few months or weeks after it is installed. Pump plungers, working barrels, balls and seats of valves, and screen pipe, as well as lead lines and other surface equipment, are ruined with equal rapidity. The development and application of practical methods to retard or prevent this corrosion are among the most urgent problems of the oil and gas industry. Although much progress has been made in preventing the corrosion of metals, the need for reducing the damage from corrosion in oil and gas fields is still imperative. This is especially true of underground corrosion in the wells, because underground conditions favor corrosion and are difficult to study; hence they have not been thoroughly understood. In efforts to stop ~amage to oil and gas field equipment by corrosion, numerous methods have been proposed or tried with varying success. Some of these methods are cheap and effective. However, it is surprising that in many important fields the damage by corrosion is accepted as necessary or unavoidable, although cheap and effective methods that have been developed and successfully tried elsewhere might greatly reduce the trouble or eliminate it. This bulletin describes common causes and effects of oil and gas field corrosion and outlines methods of abating the damage. In order to accomplish this purpose best, the writer has avoided taking sides in controversies between the advocates of different metals for oil-field use; instead he describes the methods of combating corrosion in the various fields and suggests experiments that may yield valuable results. Throughout the paper he has freely used information from published reports of other investigators.

Jan 1, 1925

By Gary A. Kingston

This examination of Pacific Northwest (Idaho, Montana, Oregon, and Washington) ferrous scrap-industry operations, principally those in Oregon and Washington, points out factors influencing the supply and consumption of scrap materials, such as the complete dependence of steel ingot producers in these States on scrap as a metal raw material and the sizable quantity of scrap exported from Seattle and Portland to Japan. The pattern of the industry is presented as a movement of materials from their diverse sources to the consuming market. The geographic locations of the consuming industries in relation to the areas generating scrap materials and the movement pattern of the supply from source to destination strongly influences the cost of the commodity. The best measure of the scrap supply available in an area is experience in terms of how much scrap was withdrawn at a given price. Scrap availability is not finite, because the return of materials as scrap is secular and influenced by constantly varying market conditions. Steel ingot producers use 75 percent of the approximate 500,000 tons of scrap consumed in Oregon and Washington; steel foundries take 15 percent of the total; and iron foundries, ferroalloy plants, and other miscellaneous consumers utilize the remainder. Also, from 1955 to 1960 an average of about 200,000 tons has been exported annually from Oregon and Washington. The foreign exports are supplemented by lesser shipments to other steel producing States, principally in the western United States. From 1955 to 1960 the preferred and higher value heavy melting scrap grades accounted for about 60 percent of total withdrawals which varied between 600,000 and 950,000 tons annually. Total crap withdrawals from Oregon and Washington are projected to 1.8 million tons by 1985, 60 percent (1.1 million tons) of which will be heavy melting grades. No. 1 heavy melting scrap is most attractive to scrap consumers at $35 per ton or less. Price-supply relationships compared with projected scrap requirements indicate future prices possibly over $35 per ton. High prices over a long period could motivate the Pacific Northwest scrap consumers to produce steel from iron ore. However, technologic changes taking place at integrated steel plants could reduce scrap withdrawals from the Pacific Northwest, which might keep the scrap price sufficiently attractive to obviate production of competitive iron products by the Pacific Northwest scrap consumers.

Jan 1, 1964

By A. C. Fieldner

In the course of its investigations on the properties of coal and in rendering fuel-inspection service to other agencies of the Government, the Bureau of Mines has accumulated a comprehensive file of coal analyses that includes data on virtually every coal field of commercial importance in the United States. As knowledge of the composition of coal is potentially valuable to every user of coal, the Bureau publishes its analytical records. Before 1921 such publications contained analyses of coal from all parts of the United States; individual analyses or average analyses of a series of shipments of coal were given with the name and location of the mine producing the coal. Beginning in 1921 the analyses were published by separate States because the quantity of data had become so great. The separate papers published to date, with Bureau of Mines Technical Paper numbers, are as follows: Alabama, 347; Arkansas, 416; Colorado, 574; Illinois, 634 and 641; Indiana, 417; Iowa, 269; Kansas, 455; Kentucky, 30S; Maryland, 465; Missouri, 366; Montana, 529; New Mexico, 569; Ohio, 344; Oklahoma, 411 ; Pennsylvania (bituminous), 590; Tennessee, 356; Utah, 345; Virginia, 365; Washington, 491 and 618 (618, published in 1941, supplements 491); West Virginia, 405 and 626; and Wyoming, 484. From time to time the various papers will be revised to include later analyses and other data. The Bureau of Mines annually receives many inquiries as to the composition of coals obtained from specific localities or, conversely, as to the localities from which a given kind of coal may be obtained. This paper presents a summary, in tabular form, of the composition of commercial coal resources of the country. Specimen analyses are given exemplifying the analysis of coal mined in each coal-producing county, or, where it was feasible, coal from each bed in each county; also, ranges of analyses, within which the composition of most of the coal represented will fall, are given where there were enough analyses to permit satisfactory determination of the ranges. In addition, the degree of metamorphism from lignite toward anthracite of much of the coal is indicated by the classification by rank. This classification reveals to more experienced users of coal some of the general properties of coal, that is, whether the flame will be long or short, whether the coal will cake in the fire, and how it is likely to behave on exposure and in storage.

Jan 1, 1942

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251, of which this is the ninth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township map. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on figure 13 in volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each half township is given with the discussion covering that area.

Jan 1, 1948

By S. S. Cole, C. E. Wood, T. L. Joseph

"INTRODUCTION Iron ore containing titanium was first used in blast furnaces over a century ago. It is well known that TiO2 is a slag-forming material that will increase the amount of slag produced by the usual gangue materials, silica and alumina. Increase in the volume of slag due to the presence of TiO2 and a lack of information concerning its effect on the properties of the slag have prevented the general use of titaniferous ore. Also rather com¬mon belief among furnace operators that the bottom of the furnace builds up when ores containing TiO2 are smelted has militated against the use of titaniferous ore. This building up of the hearth has been attributed to the formation of copper-colored crystals of titanium cyanonitride, which have been observed in the salamanders of blast furnaces. Until recently the availability of nontitaniferous iron ore has left little incentive to use ore containing titanium.The presence of vanadium in certain deposits of titaniferous magnetite in New York State has created new interest in problems connected with the use of titanium-bearing ore. It appears that most of the vanadium in this ore can be recovered in pig iron, which can be blown in a converter to produce a slag containing vanadium in amounts suitable for the production of ferrovanadium.The Titanium Division of the National Lead Co. recently erected a largo mill to treat ore from Sanford Hill, in Essex County, New York, about 50 miles west of Port Henry. The ore deposit was acquired from the MacIntyre Iron Co. and is often referred to as Sanford ore. It is one of the largest deposits of Iron-bearing material to be found east of the Lake Superior region and is being mined by open-pit methods."

Jan 1, 1943

By R. G. Warncke, Stanley M. Walker

The United States Bureau of Mines was created by an act of Congress in 1910 as a governmental agency to work , on a national scale , toward reducing the huge annual loss of life in the production and processing of the Nation's minerals . From 1906 to 1910 , inclusive , nearly 2,500 miners lost their lives in 84 major explosion disasters , and more than 13,000 suffered fatal injuries from all causes in the coal mines of the United States . Also , conditions in the metal and nonmetal mines were proportionately hazardous during this period , and the total loss of life in all mines and quarries exceeded 3,000 annually and approximately 250,000 workers suffered serious injuries . Under these conditions it is readily understandable why Congress took notice of this " high cost of mining" , and from the investigations and hearings of the day emerged the Bureau of Mines charged with the prevention of accidents and the preservation of the health of all those engaged in the mineral industry; this has continued to be a most important part of the work of the Bureau . Throughout its existence the Bureau of Mines has had no legal authority of enforcement , except during war years , when enforcement necessary to the national security was given to it . The Bureau believes that persuasion , with factual evidence , is the proper and best way to obtain compliance with the safety suggestions made by its engineers and scientists . There is no panacea for accidents , nor will any single " approach " , instill safety consciousness in all workers , and without it accidents will occur --and occur again . To persuade men to work safely, numerous forms of appeal are required to reach the various temperaments of workers in many types of mines operating under diverse conditions .

Nov 1, 1949