Search Documents

By Dr. Kyle Perry, Ryan Sibley

Rock blasting is an inherently difficult field to quantify independent & dependent variables and the specifics of how the energy interacts with the material for a number of reasons. Independent variables such as geology are innumerable and stochastic, thus, on a laboratory and full-scale basis these variables are assumed to be homogenous across the desired rock boundary. Dependent variables are difficult to quantify in the laboratory based on the specific aspect of the fracture mechanisms that caused the fracturing. The same variables are difficult to quantify in the field because of the shear amount of material being blasted. The energy interactions with the material are difficult to quantify due to the rate of the reaction and the lack of quantification of independent variables. The second main issue with laboratory scaled rock blasting is the nature of the small form-factor explosives required for use in a scaled setting. These explosives that are utilized, traditionally PETN detonating cord, have a greater ratio of potential energy converted to shock energy rather than gas energy when compared to traditional field explosives, such as emulsion or ANFO. Research over the past decades has indicated that gas pressure has the greatest contribution to rock blasting performance, such as fragmentation and material throw. The factor of varying ratios of energy production has not been discussed in any of the reviewed publications. Publications discuss dimensionless scaling, dynamic similitude, and length-based scaling, however, none of these scaling methods discuss the ratio of energy production. The main focus will be correlation of energy production ratio of shock versus gas to dependent variables. This paper analyzes previous publications within rock blasting and related field as they pertain to scaling procedures and will highlight the similarities and differences in the various publications and detail the observed omitted variables that possibly lead to skewed data.

Jan 21, 2025

By Paul L. Matrin

This paper will discuss the recent and on-going drill and blast optimization measures at the Sparkhule Limestone Quarry, which have resulted in a 44% reduction of drill and blast unit costs per ton of broken limestone. This amounts to approximately $240,000 of drill and blast saving per year at current annual production rates of about 2.5 million tons (2.3 million tonnes) total material shot. The reduction of drill and blast costs were accomplished by a detailed and controlled in-the-mine drill/blast experimentation and cost evaluation using 8 different blast pattern designs and shots totaling approximately 267,000 tons (242,200 tonnes) of shot and mucked material. A careful review of the geology of the deposit was performed to determine the different rock classification/strengths/structural properties and to adjust blast designs to optimize fragmentation for the different rock types. Equipment loading productivity and crusher throughput performance were monitored as part of the evaluation process to assure that an optimal fragmentation of broken rock was achieved with the new blast designs. The study included the review of bulk explosive and accessory selection criteria (ammonia nitrate/fuel oil mix - ANFO, mini prills (high density ANFO), sensitized and un-sensitized emulsions at a 30% emulsion/70% ANFO blend), blast pattern design, charge diameter and the cost of drilling. Laser profiling technology was used to assure proper bench heights, stemming and sub-drill footage and front row burdens. High speed photography, video and still photos were taken of the different designed shots to assist in the evaluation of the performance of each blast. Powder density checks, size distribution, back break, detonation velocity and pressure measurements were taken. Different borehole diameters were used for the drill optimization study and drilling cost and productivities determined. A detailed cost comparison between in-house blasting and complete shot service was prepared to evaluate if shot service is a cost effective alternative to current in-house loading and blasting including a review of the new and pending United States Bureau of Alcohol, Tobacco and Fire Arms (ATF) regulations and associated owner costs/risks and potential benefit of shot service.

Jan 1, 2004

By Ali Kahriman, Olivio Angelini, Ibrahim Sefer, Burak Ekmen, Koray Arpak, Ertugrul Kaya, Yucel Karakus, Abdullah Sak, Aziz Ozdemir

In recent years, in order to bring solution to traffic intensity arising from transportation problems and facilitate public transportation in the modern world in paralel to urbanization and to the increase in population, it’s well known that, the construction of Access tunnels is inevitable. The driving of the tunnels is a subject of special interest in the technique of rock blasting. The essential factors in terms of tunnel driving and safety in tunnel blasting that is applied in metropolitan areas, an in depth knowledge of ground vibrations and the ways of reducing them to safer levels.

Jan 1, 2010

By Carlos Alvarado, Hernan Narea, Jhon Silva, Bryan Townsend, Katherine Gil, Brayan Caceres, Felipe Pontanilla

With the promising development of new technologies, automation in Drill and Blasting (D&B) is on the horizon. The data generated in all D&B activities, which is currently segregated, can be linked to become information and carry a logical meaning. This information can be used to identify critical activities and make decisions regarding corrective measures to accomplish the goals of D&B. Minera Caserones, supporting Alert2Gain (A2G), and Dyno Nobel, has been working on the development of a quality assurance and quality control (QAQC), system for the mine involving all D&B activities. The main variables in the model for D&B include data from the geology of the deposit, drilling, explosive products, and material loading, among others. To create the model, the mine is divided into blasting polygons. Those polygons are part of a block model. The block model is assembled following different rules, such as: • Block sizes of 4m x 4m x 15m, • Classification of the blocks to a particular blasting polygon using a geospatial intersection algorithm, • Algorithms connect all the pieces of data automatically with the minimum of human intervention and populate the block model, Because measuring data for each block is impossible, another set of rules and algorithms completes the model. Dyno Nobel generates an essential set of data for the QAQC system. Explosive truck loading rates and explosive products, among other data, are also included in the system. The system autogenerates reports every hour, and a summary of the results of each mining day (a mining shift of 12 hours) is distributed by email to all responsible persons to identify the critical tasks and then to make the proper adjustments to accomplish the goals of D&B. The information is updated every hour and available through a dashboard for easy and straightforward interpretation. This paper explains the conceptual details of the QAQC system implemented in Minera Caserones, how the data is aggregated automatically from the different sources, shows examples of the type of information in the dashboard, and presents a successful case where a deviation was detected, and the corrective measures that were implemented to keep the performance of the D&B activity. The paper finally discusses the next steps toward an autonomous D&B system based on new AI technologies, with minimum human intervention.

Jan 21, 2025

By Tony Rorke, Sydney Thabethe

A large overburden blast was carried out at Douglas Colliery, Middelburg Mine Services, close to a national road in South Africa. The road is a busy route between Witbank and Bethal and damage to the road could not be risked. The section of road next to the blast was particularly prone to damage, because it had been mined out on its eastern flank, and the large blast was to take place on its western flank. There were thus three potential damage risks: 1. Fly rock damage to the road surface 2. Vibration damage to the road substrate 3. Damage caused by bulk displacement of the block supporting the road into the void on the mined out side. This paper presents the design and blasting methods used to control the blast and avoid these three risks. Electronic delay detonators were used in multi-decked holes. Signature data were used to determine the blast timing to make sure that delays were used that would provide destructive interference. The timing direction and sequence was decided using wave interference patterns to direct repeated shocks away from the road. The precise detonators and the odelling capability allowed effective control of the blast vibration result. Each hole was charged with two explosive decks separated by a deck of aggregate to limit the charge mass fired per delay and thus limit the reaction forces acting towards the unsupported road. The vibration and blast results are presented in the paper, together with the design that was applied. Details are provided on how the blast was charged and primed. The detonators that were used are described and the timing design is presented.Copyright © 2004 International Society of Explosives Engineers 2004G Volume 1 - Blasting Next to an Unsupported Road Using Electronic Detonators 1 of 13 It is concluded that damage risk to nearby structures can be effectively controlled using electronic delay detonators, provided the appropriate modelling is applied to obtain the most effective delay periods.

Jan 1, 2004

By B Mohanty

Currently there exist several explosive quantity-distance (Q-D) rules variously exercised by most countries to protect personnel and property against the effects of accidental explosions. These regulations apply to manufacture, transport and storage of explosive products. This paper reviews the technical basis behind these regulations, as they apply to commercial and military explosives. The characteristics of a blast wave and missiles issuing out of an explosion site and their role in determining the level of damage to a target are discussed. The need for further research on the effect of detonation of charges of non-standard geometry, and under confined conditions such as tunnels is discussed. The challenge in estimating the net quantity of explosives involved and calculation of its TNT-equivalency is also highlighted.

Jan 1, 2014

By Joshua Hoffman

The recruitment and retention of future talent into the explosives industry is becoming increasingly important. Student chapters help with this effort but what are they doing and are there things they could learn from each other? This paper discusses the University of Kentucky Student Chapter's efforts to grow membership, retain its recruits, and integrate them into the explosives industry. Several social and professional events during which the students are able to meet and network with members of their future industry are introduced. The special relationship that has been fostered between the University of Kentucky and Missouri University of Science and Technology is discussed. Professional development initiatives which are critical for a student to become vested in the industry are shared in this paper. These opportunities which range from internships to research positions allow a person to get a better understanding of the explosives industry and find the niche that best suits them. Many of the student chapters are closely connected with engineering programs. While this makes sense and both entities benefit from these arrangements there is a trend of job placement primarily in the engineering industry. By providing these students with the chance to learn more about the explosives industry and get hands on experience more of these future engineers and professionals can be retained after their graduation.

Jan 1, 2013

By A. S. Tawadrous

Fines are produced in any blasting application. Depending on the application, fines may or may not be a desirable product of the blast. In most quarry and construction applications, fines are considered an undesirable product since it does not constitute a sellable product and there are costs to the operation for disposal. On the other hand, in most open pits fines do not represent as much of a problem since the ore has to be crushed and ground after being blasted. Therefore, fines in such operations may reduce the energy consumed in the downstream operations.

Jan 1, 2012

Currently there exist several explosive quantity-distance (Q-D) rules variously exercised by most countries to protect personnel and property against the effects of accidental explosions. These regulations apply to manufacture, transport and storage of explosive products. This paper reviews the technical basis behind these regulations, as they apply to commercial and military explosives. The characteristics of a blast wave and missiles issuing out of an explosion site and their role in determining the level of damage to a target are discussed. The need for further research on the effect of detonation of charges of non-standard geometry, and under confined conditions such as tunnels is discussed. The challenge in estimating the net quantity of explosives involved and calculation of its TNT-equivalency is also highlighted.

Jan 1, 2011

By Nikolaos Petropoulos, Changping Yi, Daniel Johansson, Håkan Schunnesson

The effect of jointing on fragmentation by blasting was investigated experimentally and numerically. Firstly the experimental results were presented. Then the numerical modelling based on the experiments was performed. The same conclusions can be obtained based on both experiments and numerical modelling.

Feb 1, 2020

By Mark Roberts

Automation, data analytics and optimisation are key trends in the mining industry. Doing more, and better, while expending less resources targets KPIs around efficiency and productivity. With the explosion of data, the next step is to develop an optimal level of processes and systems to harness this data to support value-in use decisions. Typically, significant amounts of resources and effort are invested to develop realistic simulation models. However, models are frequently not integrated with existing systems, and therefore are underutilised. When we consider the specialised process of blasting, integration with upstream and downstream processes is a significant driver to realise sustained improvements and value. The application of genetic algorithms and cloud computing to solving complex mining problems has advanced over the last 15 years, in particular with mine scheduling. Genetic algorithms are unique in that they support true multi-objective optimisation, utilising population-based methods to present trade-offs between multiple solutions. Secure in-cloud processing speeds up the processing, with results delivered in timeframes that are not feasible with desktop computing.

Feb 6, 2023

By C. Mick Lownds, Dale S. Preece, Ali Bhuiyan

FDM (Fracture Density Model) is a three-dimensional mechanistic model of blast induced rock fragmentation. FDM uses several computational mechanics algorithms to simulate the effect of blasting in different rock types. Earlier, FDM was successfully exercised to simulate 29 small scale shots from the United States Bureau of Mines (USBM), and 6 full-scale bench blasts at the Bararp dimensional stone quarry in Sweden. Excellent agreement was obtained for those shots, and the results were documented in earlier publications. One of the drawbacks of previous ver- sions of FDM was its inability to predict the fines, specifically in Bararp quarry simulations. Ac- curate predictions of fines can be very useful in reducing energy consumptions during down- stream comminution processes and improve the mine-mill operation efficiencies. In this paper, we propose a newer algorithm that can predict the fines as well as the coarse fragments in Bararp with reasonable accuracy. The model was also applied to an open-pit Copper mine with heavily jointed rocks, and it produced very good fragmentation predictions for the full range of fragment sizes. Comparisons with the sieved fragmentation data (for both Bararp stone quarry and the open- pit Copper mines) show great potential for this updated version of FDM in modeling the entire range of fragment size distributions in mining and quarrying applications.

Feb 6, 2023

By Andrew Wetherelt

Blast vibrations are of paramount importance in a society where ever increasing development is putting more stringent requirements on their control. Increasing civil development and more complex extraction scenarios make the trade off between proficient vibration control and productivity difficult to ascertain. Historically, reduction of induced vibrations levels was achieved through a reduction of MIC’s leading to smaller but more frequent blasts in order to meet extraction targets.

Jan 1, 2007

By James A. Bachmann, Christopher J. Gray

On December 26, 1994, at 1:00 am, Santa Fe Pacific Gold's Twin Creeks Mine experienced a major highwall failure involving over 2.5 million tons. The resulting effects of this slide were thousands of ounces of gold that were now deferred and an unstable wall above which made mining the slough material unsafe.

Jan 1, 1996

By Roland Alford

The ballistic pendulum is a well-established piece of test equipment originally developed for estimating the velocity of bullets and projectiles. When trying to understand the effects of different tamping methods on explosive performance, the ballistic pendulum is an excellent tool allowing calculation of explosive charge impulse. Most ballistic pendula for this application are limited to narrow impulse ranges as the pendulum mass determines the angle of swing; and a mass capable of being moved by a small charge would be far too small for a larger charge. This paper describes a modular design (the Alford Modular Ballistic Pendulum) which overcomes this problem.

Feb 6, 2023

By Brian Warner, Siavash Mahvelati, Douglas Rudenko, Mohamad Sharif

Predicting and optimizing production shot vibrations using time-shifting and superposition of signature hole waveforms (seed waves) has been widely used for many years. In this method, a single borehole is detonated and recorded with seismographs at the locations of concern. Since a single hole waveform is a reproducible event, it is reasonable that the seismic signature from a multi-hole production shot can be predicted by summing a series of single hole waveforms that have been time‐lagged at intervals corresponding to delay times from the production shot. However, there are instances where seed waveforms are collected at locations other than the exact location of concern, which raises questions regarding the applicability of such recordings. The present study adopts the well-known concept of dispersion of surface waves to predict seed waves at a location of interest based on seismograms recorded at a closer offset. Surface waves, as their name suggests, are seismic waves that propagate along the Earth's surface. They are the dominant wave type within one wavelength from the ground surface. Surface waves are dispersive in nature meaning that in a layered medium, wave components with different frequencies travel at different velocities causing an input signal to disperse as it propagates. The proposed technique takes seed waves recorded at one location as the input and passes it through a frequency-dependent function developed using site dispersion characteristics. The site’s dispersion characteristics are either measured directly with surface wave methods or retrieved using shear wave velocity information. The output of the function is the seed wave prediction at the farther location of concern. The theoretical background, including the underlying assumptions and limitations, is discussed in detail, and the application of the technique is illustrated through field data from two sites.

Jan 26, 2026

By Syed Haq, Kyle Optt, David Campo, Doug Anderson

Limitations on allowable levels of vibration from construction activities generally consider either annoyance or damage. While activities such as drilling and roller compaction primarily create annoyance, the major concern for blasting is usually damage. Many years of research have developed correlations between peak particle velocity and either threshold or structural damage. We emphasize the term “correlation” for two reasons. First, peak particle velocity is only a single-valued representation of a vibration waveform, and does not characterize it completely. Second, a given peak particle velocity by itself, even a particle velocity waveform, will not damage anything – strain does. Why not measure strain all the time? Strain is very localized, and can vary substantially over short distances, so choosing the appropriate strain measurement can be difficult. Measurement of strain is appropriate when either the behavior of a specific structural element is needed, or the overall response of a structure can be adequately represented by a well-selected strain measurement. We will discuss the appropriateness of both particle velocity and strain as deformation and damage descriptors, in general. We will also describe a specific case history, from a tunnel project in New Jersey, correlating strain with peak particle velocity. Finally, we will make recommendations for the choice of measurement type for some common situations.

Jan 1, 2004

By Alan Diaz Butron, Eng. Thierry Bernard

"In tunnel blasting the most challenging objective is definitively obtaining the maximum advanceassociated to a minimum overbreak. Achieving 100% of advance with no overbreak is the targetchallenge by Chavimochic Consortium. Chavimochic Special Project is an irrigation system that extends throughout much of the coast of the La Libertad Region, on the north coast of Peru. In 2012, it began management for construction of the third and last stage of CHAVIMOCHIC to irrigate lands of Chicama Valley, North of Trujillo. This project of 13 Km (8 mi) of various tunnels, it's a combination of technology and daily optimization by experienced people, which allow to accomplish the objective. Achieving this advance with no overbreak provide a huge saving on time. This paper describes the method, technology used, and the results obtained on more than 600 blasts done with conventional initiation system on the first 3 km (1.86 mi)."

Jan 1, 2017

By W. De Graaf, C. Mkumbo

Bulyanhulu Gold Mine Limited (BGML) commissioned a project of sinking a Bulk Air Cooling Shaft during its programme to improve the ventilation system on the mine. As part of this project, a ventilation drift had to be developed and holed into the Main Shaft at 4920 Level. AEL Mining Services (AEL) were requested to provide a technical solution, which included monitoring of blast induced vibrations and to design drilling and timing plans to ensure blasting activities on the vent drift were conducted without disrupting the main shaft’s infrastructure.

Jan 1, 2011

By Clara Godoy, Paulo Couceiro, Juan Navarro

The continuous automatization and digitalization of the different stages involved in any underground construction bring new possibilities to optimize the operation. One of the most important requirements for the development of these projects consist of a proper rock mass characterization for optimizing the stages of the drilling, blasting and support cycle. In the last few years the road to digitalization has gone through data science and big data, showing the importance of data gathered to describe the geological and geotechnical environment that surrounds the operations. Since rock characteristics have an important influence in the drilling response, the technological advances in the sensorization of drilling machinery such as the Measurement While Drilling system (MWD) allow to gather the necessary amount of information to be applied in data science processes to evaluate changes in the rock mass with higher resolution than conventional methods. In this paper, Machine Learning techniques have been used to combine data monitored from the drill rigwith scanner profiles of the excavated sections to develop an automatic geotechnical rock mass characterization model able to estimate potential zones of over- or under-break of the remaining rock mass in underground blasting. By comparison of scanner profiles of the excavated sections with the blasthole positions, an Excavated Mean Distance (EMD) between the contour blastholes and the excavated profile has been obtained, which may be considered as damage measure. Considering blasting factors as constant, the model combines the rotary, percussive, hydraulic flushing and the rate of advance of the drilling, and the confinement of the rock mass by depth, to detect zones with different rock properties. This provide an early information of the rock mass condition around the blastholes and the prediction of expected overbreak generated after blasting, being possible to design more efficient bastings, in which each borehole is filled with the right and necessary explosive charge. The analysis comprises data from 57 blasts (around 1700 contour blastholes) and more than 4000 excavated sections.