Search Documents

By S. V. Ulianov, A. Y. Senchenko, E. M. Kurchevskaya

"A process sample of old copper-containing tailings (-2.0+0 mm) from an iron-ore plant was tested in TOMS institute in order to develop a process for copper concentrate production. The study of tailings material composition indicated that -0.2+0 mm fraction was efficient and contained 97.26% of copper. Copper is predominantly concentrated in chalcopyrite which is present both in free form and in intergrowth with ore and rock-forming minerals. Study of chalcopyrite using an optical microscope and Qemscan SEM determined that the most grains surface was covered with oxide films. Additionally, a lot of grains had micropores on their surfaces that indicated a partial mineral leaching. The oxide films did not make it possible to float copper minerals from head material. It was recommended to apply an attrition operation to restore chalcopyrite floatability. In order to increase selectivity a regrinding stage for a primary copper concentrate was introduced to obtain P80 26 um. Taking these recommendations into account a flotation flowsheet was developed to process the old Cu-containing tailings. The flowsheet allowed us to obtain a concentrate with 23.5% Cu content at 71.5% recovery.INTRODUCTIONStudy of material composition is an important prerequisite for development of a minerals processing technology. Mineralogical study contributes to search for an efficient technology to recover valuables and for prospective methods of minerals processing.The use of such up-to-date analysis methods and equipment as Qemscan and Mineral-C7 allows one to determine minerals size, liberation degree, and mineral associations. Mineralogical data can reveal reasons for hard processing of minerals prior to development of the process.The advanced process mineralogical methods used to study Cu-bearing pond tailings indicated several factors that influenced development of the process. The first one is a barren size fraction which is to be removed from the process in order to considerably reduce the costs connected with grinding. The second is the presence of films on chalcopyrite surface; in this context, a preliminary attrition of the material was recommended. The third factor is finely disseminated Cu minerals in sulphide and in the rock, which predetermined selection of particle size for flotation. All these data led to significant decrease in time required to develop the process technology. The developed process flowsheet based on the obtained mineralogical data is present in Figure 1."

Jan 1, 2016

By J. E. Dutrizac, J. B. Sunstrum

"Lead was among the first metals known to man, and there are indications that lead was produced by the reductive smelting of galena in the mountains surrounding the Black Sea as early as 3000 B. C .(1). The early metallurgists soon discovered that silver could be recovered from lead bullion by cupellation techniques, and that the litharge product of the cupellation process could be reduced to give silver-free lead metal. By the Graeco-Roman era, lead-silver ores were being extensively exploited for both their silver and lead contents. Although silver was always of prime concern, a number of industrial uses existed for lead that included piping and sheeting. Subsequently, lead metallurgical practice developed steadily in different parts of the world, and was a relatively mature technology by the time of the European colonization of North America. In the United States, lead was produced on a small scale as early as 1720, and by 1800, the extensive Pb-Zn deposits of Missouri-Kansas and the upper Mississippi Valley were being developed(2). Many of the early American lead ores were low in silver, and seemed to have been worked primarily for their lead contents. Major uses of lead at the time included bullets, pipe and sheeting. During the period 1860-1890, the silver-rich galena ores of the western United States were exploited, and a number of lead smelters were operated. Although all the smelters produced lead metal, the recuperation of the associated silver and gold values was generally of prime concern. In Canada, lead deposits are abundant, and galenarich outcrops frequently attracted the attention of the early explorers and prospectors. In fact, the first record of a Canadian ore deposit seems to have been the observation of an argentiferous galena vein near Lake Temiscamingue in 17 41(3). The presence of silver-bearing lead deposits naturally attracted the attention of the mining community, and many outcrops were worked throughout the country. Because of the problems associated with transporting lead concentrates to existing American or overseas smelters, attention soon shifted to the establishment of local lead smelting facilities. The purpose of this article is to examine those early smelting efforts and to try to identify the first ""successful"" Canadian lead smelter."

Jan 1, 1999

By Gurupraveen Ramanathan

Slot raises are relief holes within a stope in longhole stoping methods, designed to provide a free face that facilitates the expansion of the blasted rock during blasting, ultimately achieving the desired fragmentation. Various methods are employed to produce these slot raises, like conventional drop raise drilling, raisebore & V30 drilling. However, slot drilling is generally characterized by high costs and limitations in precision, resulting in unplanned ore losses and dilution. This paper introduces a novel alternative to slot drilling referred to as the "paste slot", designed specifically for paste backfill operations in underground mining. This new method emphasizes considerations in cured paste strength, paste wall removal, and stope dimensions and employs modified drop raises or dumped rings to optimize blast gas effectiveness and material flow. The paste slot method eliminates the need for reamers and reduces the total slot drill meters an average from 650m to only 300m for narrow stopes (3-4m wide). This significantly reduces the stope cycle time, leading to substantial cost savings and increased productivity. This new method was successfully implemented at the underground mines in Canada and Australia, resulting in a 20% reduction in stope cycle time and cost savings of 53,000 USD per slot compared to the conventional slot. This paper discusses the design and execution strategy of the paste slot method in underground paste backfill operations. It highlights the advantages of the method, shares operational insights gained during implementation, and showcases its potential applicability to other mines across Canada and globally.

Oct 1, 2024

By H. G. Wang

The production process of a coal mine can often be interrupted by all kinds of events scheduled or unscheduled and thus often needs gas drainage for a temporary or long-term sealed area. Gas drainage has a relatively high risk, therefore attention must be paid to its design to keep the process safe. Based on the conservation laws of mass and constituents, and under the conditions of the allowable gas concentration limit in the return air route, the relationship between gas concentration and gas drainage flow rate as a function of time during the drainage process is discussed in detail to build a mathematical model of gas drainage from a sealed area. With respect to the gas drainage process, two different conditions need to be considered: one with a methane free fresh air supply, the other with a low gas concentration. This paper presents the derived mathematical models for these situations and then shows that they can be incorporated into one model with some modification. This combined model can be employed to determine the optimum gas drainage flow rate with the shortest drainage time. The application is coded using the C# programming language within the .NET framework. Finally, the application program developed by the author is used to validate the mathematical model through an example of gas drainage with varying rate.

Aug 1, 2013

By I. Murray, N. Geoffroy

"Buried pipelines, tanks and other similar equipment are almost always present on large scale industrial sites, including in the oil and gas fields. However, as the proverb “out of sight, out of mind” suggests, it is easy to overlook proper maintenance procedures and simply assume that corrosion protection measures in place are working correctly. Unfortunately, this is not always the case, leading to significant environmental damage and loss of production. This paper describes several cases from various industries where buried equipment failed because of corrosion, sometimes with catastrophic results. It also presents various strategies, based on experience and new research, to help predict and prevent damage to underground metallic structures.INTRODUCTION Metallic underground structures are extremely common in industrial and commercial settings for numerous reasons. Burying pipes, tanks, wires and other similar equipment has numerous advantages: it provides significant protection from mechanical damage, frees up ground space that can be used for other purposes, requires little to no support structure and is generally more esthetically pleasing. However, this last benefit can also be considered the most significant disadvantage of underground equipment: becoming invisible and forgotten. While every engineer is aware of the importance of preventive maintenance, it is also human nature to somewhat forget about equipment that is hard to inspect and assume that everything is fine. This is unfortunately not always the case and failures in industrial settings can have extremely serious consequences. While economic aspects immediately come to mind (loss of production, cleanup cost, etc.), failure of underground equipment also results in an environmental and therefore public relations nightmare, especially in the oil and gas field. Leaks that would have been considered negligible in the past can now make national headlines and perfect reliability, while probably impossible to achieve, is now the goal of most companies. While environmental damage (real or perceived) is most often associated with leaks in the oil and gas industry, it can also affect the mining world. For example, the authors have worked on a project where a buried slurry pipeline had ruptured in the ground, causing a release of perfectly inert tailings. While the economic loss was low, the leak was reported in local media and caused a public relations problem."

Jan 1, 2017

By Ron Light, Doug Applett

"HistoryThe Nanisivik mine began operation in October 1976 as the world's most northerly metal mine and the first permanent industrial project in the Canadian High Arctic. Located 700 km north of the Arctic Circle on Baffin Island's Strathcona Sound, exploration by Texasgulf Inc. between 1957 and 1970 had outlined the ore deposit. In 1974, Nanisivik Mines Ltd. was formed with Mineral Resources International, the Government of Canada, Metallgesellschaft and Billiton being shareholders, and Strathcona Mineral Services Ltd. providing project management. In 1996, Breakwater Resources purchased the mine from Alberta Energy Corporation Limited which had recently acquired the assets of then owners Conwest Exploration Ltd.Ore DepositThe main ore deposit is very flat, approximately 80 m in width and varying in thickness from 3 m to 16 m. The length of the deposit is approximately 3000 m with satellite zones located on the perimeter of the main zone. The economic mineralization is sphalerite with minor galena and silver. The sphalerite and galena are coarse grained and associated with pyrite as the main gangue component with minor inclusions pf dolomite and calcite within the deposit. The deposit being hosted in a permafi·ost environment creates a number of challenges. Dry drilling is employed in room and pillar production drilling. The permafrost aids in the stability of both the pillars and the back."

Jan 1, 2000

By J. L. Bowlby

Introduction In the following discussion, boiler-feed and mine waters will be considered from the point of view of the problems arising from the chemical nature of the mineral and gaseous impurities they contain. The theories underlying some of these problems will be reviewed for the purpose of getting a clearer concept of the problems themselves. Certain terms of a chemical nature, necessary to the discussion, will be explained on the assumption that they are not generally familiar to mining engineers. Finally, an attempt will be made to correlate theory and practice, with the abject of establishing certain limits to factors relevant to the problems, and to show that these limits are justified by practical experience. The general problems occasioned by the presence of mineral and gaseous impurities in boiler-feed and mine waters are: (1) Scale formation and corrosion in boiler systems. (2) Corrosion of mine pumps and pump fittings. These will be discussed separately. Boiler Scale Typical analyses of waters available for use in steam power-plants are given in the accompanying Table (Table I). All analytical data are expressed in grains per Imperial gallon. The bicarbonates of calcium and magnesium in the raw waters are shown as normal carbonates in the Table. Substances in the first five rows constitute the encrusting solids. All the waters listed in Table I would be classified as 'very good' in the schedule of classification for boiler waters adopted by the American Association of Railway Chemists in 1887. In spite of this classification, however, the waters contain sufficient encrusting solids to cause serious scale trouble after prolonged evaporation.

Jan 1, 1934

By J. H. Canterford

The nickel industry in Australia has followed the general pattern apparent in many other regions - lots of ups and downs, successes and failures, but always plenty of challenges. Some of these can be attributed to local geographical and infrastructure factors, others to a healthy mix of corporate good luck and management countered by decisions that, in retrospect, were less than optimum. The roles of several entrepreneurs have certainly added plenty of spice! In terms of processing technologies, there was an initial heavy reliance on the use of "off the shelf' commercially proven processes such as ammonia leaching of concentrates and mattes, and flash smelting. Over the past decade there has been an increasing dominance of plant modifications and process technologies that have been developed "in house" in order to enhance project economics and exploit lower grade and more complex resources. This presentation provides an overview of the past 40 years of the major developments in the Australian nickel industry and concludes with some guesses as to where we will be in another decade or so.

Jan 1, 2005

By Frank D. Adams

The Island of Ceylon, which is one of the most beautiful possessions of the British Empire, has been an abode of man from the very earliest times. The Veddhas, a wild tribe of some 4500 people still living in the fastnesses of the jungle in east central portion of the island, are believed to represent a remnant of the oldest inhabitants of which we have any actual knowledge, but in the caves in which they live there are found the stone axes and other implements of Palaeolithic people who represent the first race of men who inhabited our globe, and of whom they may be, for all that is known, the direct descendants. About the fifth century before Christ there came the Aryan invaders, apparently from the north of India, who drove the Veddhas into the remote fastnesses of the jungle and developed the remarkable Singhalese civilization whose high character is demonstrated by the remarkable and very extensive system of irrigation works which they built up, and through which they made the island wonderfully productive. Great cities arose, some of which are believed to have had a population of over a million souls and whose temples and public buildings show that the people were accomplished architects and sculptors.

Jan 1, 1926

By Maurice A. Roche

Introduction Most of the Flin Flon ore-body, like many others in northern Canada, was covered by water. The original discovery was made where the ore-body outcropped on a strip of land jutting out into Flin Flon lake. The outcrop could be traced for a distance of 600 feet across the strip of land, but disappeared under the lake on both sides of the peninsula. Following the discovery or location of the property, in 1915, and subsequent to its examination by the H.P. Whitney interests in 1925, an extensive diamond-drilling programme was completed, which proved the existence of an ore-body at least 2,600 feet long and 900 feet deep. In plan, the central part of the ore-body at surface attains an overall width of about 450 feet; including waste horses, and gradually becoming narrower to the south. To the north, it stretches out as a much narrower tongue. The main body is a solid sulphide ore containing gold, silver, copper, and zinc. Adjacent to, and on the footwall side of, the solid sulphide ore-body, there are considerable widths of talcy disseminated copper ore, particularly in the upper 300 feet of the deposit, where the maximum widths occur. The ore-body occurs in a greenstone area, the rock being quite hard on the hanging-wall side, with the footwall schisted, talcy, and much softer. The greater part of the ore-body was overlain by 12 to 15 feet of water and from 15 to 90 feet of mud and clay, this material requiring eventual removal, regardless of the system of mining adopted. The total of mud and clay overburden was estimated at 1,000,000 tons. After considerable study, it was decided to mine the upper 300 feet of the ore-body by open-pit methods; the balance of the ore to be recovered by underground mining . The present paper gives an account of the methods adopted in both operations, and of the problems encountered.

Jan 1, 1935

By W. E. Davies

"This paper is the sequel to that on Developments in Sintering Efficiency delivered by Davies and Mitchell at the International Ore Dressing Congress, Stockholm, 1957. Attention is drawn to the fundamental concept of sintering as a heat transfer process, in which the ignition heat is continually transferred onward through the bed as a heat wave. By its passage, this heat initiates endothermic 'changes, such as carbonate decomposition, whose energy requirements are supplied by the combustion of the fuel contained in the bed.Ideally, the heat wave should be generated by the ignition hood followed by the pre-heating of the incoming air. The fuel content of the bed should be no more than the theoretical quantity needed to balance the endothermic changes. In practice, the heat wave is seriously short of energy and this is offset by excess fuel in the bed. As a result, sinter quality suffers, more return .fines are produced, and fuel is wasted, a loss of efficiency which could be avoided if the fundamentals of correct ignition were more widely appreciated.Sintering speed, otherwise heat wave velocity, is a function of the rate at which the incoming air acquires .heat from the cooling sinter and imparts it to the unburned feed below the combustion zone. It is thus a function of rate of air flow and so depends on bed permeability>. Ways of• improving and maintaining permeability at the maximum consistent with thorough sintering are discussed, particular reference being made to taconite concentrates. The possibilities of recrystallizing refractory ores into forms more amenable to physical concentration techniques by sintering are visualised, very little expenditure on heat energy being required when the process is operated near the ideal conditions."

Jan 1, 1960

By L. Bichler

Utilizing thermal analysis techniques, pioneering research into the solidification mechanism of a popular magnesium alloy AZ91E cast by the Lost Foam Casting (LFC) process was carried out, Foam characteristics, section thickness and application of vacuum were seen to have profound effect on the cooling rate, thermal gradients and casting temperature profiles.

Jan 1, 2005

By J. H. Crocket, J. Andy Fyon

"All gold deposits within the Tisdale Group are spatially associated with carbonate alteration zones; however, not all carbonate alteration zones are host to gold mineralization.Within the komatiitic and magnesium tholeiitic volcanic rocks at the base of the Tisdale Group, discordant and stratabound carbonate alteration zones occur throughout. The alteration zones consist of a ferroan dolomite - quartz inner assemblage which is enveloped by calcite-quartz and an outer chlorite-rich subzone. Factors which control the distribution of carbonate alteration include joint systems, flow contacts, synvolcanic faults and bulk composition of the host rock.Two environments of carbonate alteration can be recognized: 1) The subsea-floor alteration zones developed within the volcanic rock succession where hydrothermal fluids did not discharge directly onto the sea floor. Insignificant gold production has come from this alteration environment. 2) Seafloor zones, which represent points of hydrothermal fluid discharge into the hydrosphere, are spatially associated with felsic volcanic rock complexes and are host to syngenetic, auriferous cherty dolomite.Carbonatized, magnesium tholeiitic basalts, which are host to the auriferous, cherty dolomite, are enriched in antimony (>0.35 ppm), boron (>30 ppm), gold (>5 ppb) and lithium (> 35 ppm), but are depleted in copper ( < 70 ppm), with respect to carbonatized basalts not associated with gold. Orerelated, altered komatiitic flows can be screened using gold (>5 ppb), lead(> 10 ppm), arsenic(> 70 ppm) and antimony (>1 ppm).The habit, petrographic characteristics and certain geochemical characteristics of the altered volcanic rocks suggest that the hydrothermal fluid was of sea-water origin."

Jan 1, 1982

By K. Poorhaydari, B. M. Patchett, D. G. Ivey

In this paper, some applications of carbon extraction replicas, as samples for transmission electron microscopy (TEM), are discussed. Modern high strength microalloyed (HSMA) steels, used as structural or pipeline materials, have very small grains with substructures. Replicas used in TEM can resolve the grain boundaries and can be used for grain size measurements in cases where the small size of the grains pushes the resolution of conventional optical microscopes. The grain size variations obtained from replicas correlated very well with mechanical property variations, indicated by hardness, in the fine-grained heat-affected zone and base metal of some welded HSMA steels. Replicas are also very suitable samples for precipitate examination with analytical TEM. Advantages and limitations of the application of replicas, as well as some corrections for the estimation of the volume fraction of fine precipitates, are discussed.

Jan 1, 2005

By Allan F. Lawrence

"I AM SURE you do not expect from me any learned dissertation on the problems and opportunities of the mining industry. Y our program committee must have recognized my limitations when issuing the invitation to speak to you, because they very thoughtfully left the subject wide open.With the leeway thus granted, I hope that you will bear with me for a few minutes while I try to clarify the impressions of the mining industry that I have gained in the very short time I have held the Mines portfolio and some of the parts that government bas or should have in furthering its development.As I see it, it is the duty of the Mines Department, as an arm of the provincial government, to balance the proprietary rights of all the people against the interests to whom the privilege of developing our resources are, in a s e n s e, leased. To strike a fair balance is not always easy, nor is it possible always to satisfy both sides. Still, under the free enterprise democratie form of government to which I think we al! subscribe, no better way of handling the problem has yet been discovered."

Jan 1, 1968

By K. Kryst, K. Elkayar

The increasing need to process lower grade contaminated copper concentrates and simultaneously produce higher purity copper cathodes necessitates a more diligent control in the electrorefining process. Ion exchange processes can be a powerful tool in controlling electrolyte impurities to ensure trouble free operation within the tankhouse and to help maintain cathode purity. In addition, some impurities can be recovered as a value added product. The use of a short bed ion exchange process provides a unique opportunity for impurity management in copper refineries. Several metals are discussed in this paper, including Sb, Bi, As and Ni and their methods of control and recovery within the copper electrolyte circuit. INTRODUCTION To produce a high purity copper product by electro-refining a copper electrolyte, it is important to control the concentration of impurities such as arsenic (As), bismuth (Bi), antimony (Sb), and nickel (Ni). These impurities are introduced into the electrolyte from the copper anode and can affect the copper product and the production operation. The presence of As in the copper product results in a lower electric conductivity and reduced workability of the copper. High levels of Bi in the electrolyte will result in a copper cathode product containing Bi. High Sb concentration will cause undesired floating slimes. A variety of methods have been developed to control the level of these impurities in the copper electrolyte including precipitation, liquid extraction, and ion exchange. These impurities can be recovered and used. This paper discusses novel methods that utilize short bed ion exchange technology to control these impurities. Also, the use of ion exchange to recover acid from the liberator cells bleed for reuse in the tankhouse is reviewed. SHORT BED ION EXCHANGE Short bed ion exchange technology has been employed extensively in the metal finishing industries for over forty years. Unlike conventional ion exchange, short beds are fixed beds without freeboard space. The application of short bed technology results in significant benefits when compared to conventional ion exchange. The resin used in this technology has a significantly smaller diameter than conventional ion exchange resin. As a result of the smaller resin size, exchange kinetics improves dramatically. This facilitates operation at higher flow rates and the use of smaller beds with a small mass transfer zone length. Smaller beds are especially important for applications that use chelating resins due to the high cost of the resin.

Jan 1, 2019

By Binbin Luo, Northeastern University, Chuanyao Sun, Jie Liu, Yimin Zhu, Yanjun Li

"A series of new type collectors a-bromo-saturated fatty acids, CH3(CH2)5CHBrCOOH (a-BHA), CH3(CH2)7CHBrCOOH (a-BDA), CH3(CH2)9CHBrCOOH (a-BLA), CH3(CH2)11CHBrCOOH (a-BMA) were synthesized from saturated fatty acids and bromine by solvent-free method (Hell-Volhard-Zelinski reaction) in laboratory. The micro-flotation tests of quartz mineral were conducted at a relatively low temperature of 15 °C. The adsorption mechanism of such collectors on quartz mineral surface were established by zeta potential measurements, in conjunction with the results of quartz micro-flotation tests. The flotation results showed that the collecting ability is in the order of a-BMA > a-BLA > a-BDA > a-BHA for the flotation of quartz mineral, which also demonstrating that the a-bromo-saturated fatty acids (a-BFAs) are new selective collectors for reverse flotation to remove quartz mineral from iron ores at a relatively low temperature.INTRODUCTIONThe requirement of higher pulp temperature to maintain the activity of fatty acid anionic collectors which have been widely applied in technological process of iron ores reverse flotation lead to a great deal of energy consumption.The purpose of this paper is to synthesize a new modified collector with carbon chains from eight to fourteen atoms, with strong electronegativity bromine atom introduced into a-carbon position to improve the activity and solubility of the reagent so that it can be adopted at a comparatively low pulp temperature. The collecting performances of these new collectors on quartz surface were studied, and the structure - properties were discussed in light of zeta potential measurements and quantum chemistry calculations."

Jan 1, 2016

By I. I. Bethcherman

Introduction 1.-lmportance of Physical Nature of Condensates The metals of commercial interest which have reasonably high vapour pressures below 1,200° C. are mercury, cadmium, sodium, zinc, magnesium, lithium, and calcium. With the exception of mercury, these metals occupy high positions on the electrochemical series and form compounds with very high negative free-energies of formation. It is highly desirable that such metals should not be produced in a form which is finely divided, on account of their reactivity with atmospheric gases. Powders of magnesium, calcium, and even zinc (blue powder) are dangerous to handle and cannot be coalesced by simple melting techniques. Vaporization in vacuo forms a convenient method of handling and purifying the alkaline earth metals in particular and a previous paper by the authors dealt with some of the factors controlling the separation of metals by this technique (12). An essential part of the operation is the condensation of the vapour to produce a massive deposit which may be conveniently melted and handled by established metallurgical techniques. This investigation sought to determine the conditions affecting the nature of solid condensates.

Jan 1, 1951

By X. Zhou

"Hydrogen induced failure and degradation in structural metals, namely hydrogen embrittlement, has been a long-standing industrial problem for more than one century and remains unsolved. Despite the proposal of numerous models, no consensus has been reached, and considerable discrepancies in experimental observations and theoretical calculations exist. One aspect that is central to the understanding of hydrogen embrittlement is the interaction between hydrogen and grain boundaries. In this study, we investigated the influence of several solute elements (i.e., Cr, Mo and Nb) on hydrogen segregation at the representative 9 grain boundary using first-principles calculations. Our results showed that the presence of Mo and Nb can reduce the tendency of hydrogen segregation at grain boundaries, while meanwhile enhance the grain boundary strength. This indicates that Mo and Nb are salutary elements that can be used to increase the material’s resistance to hydrogen embrittlement, providing new insights in designing hydrogen embrittlement resistant Ni alloys. INTRODUCTION Hydrogen embrittlement (HE), a phenomenon of hydrogen triggering premature failures in structural metals, has been a headache for industries ever since its first discovery one century ago (Johnson, 1874; Zhou, Marchand, McDowell, Zhu, & Song, 2016; Zhou, Ouyang, Curtin, & Song, 2016). It is well accepted that the segregation of hydrogen at microstructures such as grain boundaries (GBs) plays a key role in determining the occurrence and severity of HE. GBs are two-dimensional defects where significant local lattice distortion exist, which leads to large free volume and thus locations for hydrogen trapping and segregation. Numerous works have clarified GBs as the energetically preferable places for hydrogen segregation. For instance, Geng et al. demonstrated the preferential segregation of hydrogen at the S5(120) GB in several metals, and suggested a decohesion-type of HE in light of Rice-Wang thermodynamic theory (Geng, Freeman, & Olson, 2001). Birnbaum et al. illustrated that complete intergranular crack of Ni GBs can be induced by hydrogen segregation when the hydrogen concentration is sufficiently high, evidencing the significant role of hydrogen accumulation on GB weakening (Lassila & Birnbaum, 1987). Yamaguchi et al. demonstrated strong segregation hydrogen also occurs at S3 GBs in alpha-iron, showing that local hydrogen clustering (i.e., multiple hydrogen atoms, up to six, per unit cell) can be trapped at the S3 GB (Yamaguchi, Kameda, Ebihara, Itakura, & Kaburaki, 2012)."

Jan 1, 2017

By H. Yasuhara, N. Kinoshita, S. Nakashima, K. Kishida

"In this study, flow-through experiments in fractured rocks have been conducted under different stress, temperature, and pH conditions so as to understand the evolution of permeability induced by these conditions. Throughout the experiments, the confining pressures and temperatures are well-controlled. Effluent concentrations are also measured for the ten elements of Si, Al, K, Fe, Ca, Na, Mg, Ti, S, and Cl that are included mainly in the targeted rocks. In the early stage of the experiments, the fracture permeability measured abruptly decreases with time, and subsequently reaches quasi-steady state within a relatively short period. In contrast, the permeability in the intact rocks monotonically increases with time. The permeability increase and decrease are attributed likely to the relative dominance of mineral dissolution in the pore spaces and to that of mineral dissolution/crushing at the propping asperities within the fracture and/or mineral precipitation onto the free surfaces, respectively. The evolving rates and magnitudes of the permeability are likely to be controlled by the stress exerted over the contacting asperities, temperatures, and pH of the permeant. Thus, this complicated behavior should be attributed to the coupled chemically- and mechanically-induced effects, which should be examined in more detail for longer period to contribute to the safe entombment of radioactive wastes. INTRODUCTIONUnderstanding of the flow and transport characteristics of porous/fractured rocks is required for the safe and long-term geological isolation of energy-related by-products (i.e., high level radioactive wastes and anthropogenic CO2). Notably, under relatively high temperature and stress conditions, mechanically- and chemically-mediated processes may alter the pore structures in rocks, resulting in an irreversible evolution of the flow and transport behavior. Augmentation in permeability may result from mechanical dilation due to shearing and mineral dissolution within the pore spaces, while reduction may result from reversible or irreversible mechanical compaction, mineral dissolution at the contacting areas, and clogging of pore spaces by precipitation of secondary minerals."

Jan 1, 2015