Search Documents

By H Weitz

Bateman Engineering provided process technology and engineering design to China Yunnan Metallurgical Company (CYMCO) for a 30 MW DC furnace for the production of high-grade titanium dioxide slag.Following the successful commissioning of the furnace during the latter part of 2009 and the first quarter of 2010, a period of adverse circumstances resulted in having to operate the furnace without feed and at a low power input for a period of time. When normal feed resumed, a layer of solid material was detected on the slag-iron interface during sounding measurements. The condition of the iron was also significantly altered. The iron temperature was much higher than the design value, but the carbon content had decreased to such an extent that a large amount of iron solidified in the furnace, which made iron tapping very challenging. The slag temperature was increased in order to melt the solidified iron. However, severe sidewall damage resulted, which finally led to a burn-through. A number of samples were taken from the slag that remained in the furnace. These samples were analysed to determine the chemistry and phase profile throughout the slag bath. The mechanisms of formation of the high melting-temperature phase on the slag-iron interface are discussed, as well as procedures that can be applied to prevent a recurrence of this phenomenon. Some recommendations are made for instances when furnace feeding is interrupted for an indeterminate period.

Oct 5, 2011

By J Hutchings

An essential component to the management of any process is the measurement of key parameters, used to monitor, control, and provide the feedback necessary for improvement. This paper discusses how data collection and analysis can provide a better understanding of the blasting process, as well as additional control and improved outcomes.The drill and blast process involves the generation and use of information at a number of levels. Comparison of historical parameters and results provides a starting point for the development of ongoing blast designs and a baseline against which future results can be compared. The collection of data during implementation provides a quality assurance/quality control (QA/QC) function where potential defects (such as under-drilled or over-charged holes) can be rectified prior to firing. Actual quantities and production rates allow the development of realistic plans and schedules, rather than using inaccurate estimates and targets that lead to unscheduled changes to equipment paths. Over?the past several years there have been a number of technological advances in data collection technology. Drill monitoring instrumentation on blasthole drills provides location information and feedback on rock properties as drilling occurs. Hand held ‘data logger’ technology has also overcome the challenges of working on the bench, such that blasthole measurements can be collected and forwarded directly to the explosive truck. Mine sites are becoming wireless network-enabled allowing the seamless data transfer from the field back to the office, in near real time, as that information is collected. Great strides have also been made in the development of drill and blast software systems which are more user friendly, and yet provide far greater capability to manage the quantity of data generated. The blasting process is critical to the overall mining process and the delivery of a successful blast outcome requires that the blasting process be ‘in control’. The measurement of key parameters can provide the data with which to measure and maintain control of blasting, and allows the validation of performance improvement measures and identification of improvement opportunities.

Nov 8, 2011

By G Collecutt, T O’Beirne, D Humphreys, J Greenwood

Much of our knowledge of the behaviour of underground coal dust explosions has been derived from less than full-scale experimental explosions in facilities as small as 0.25 m diameter pipes. Although a substantial body of research has been undertaken in larger galleries approaching the size of full-scale modern mine roadways, there are still questions regarding the scaling of results to full-sized roadways in modern coalmines. Questions also surround the issue of comparing or scaling results between smooth and rough walled galleries, round and rectangular galleries and galleries with differing wall thermal properties due to different materials of construction.This paper will examine the influence of gallery size, cross-section area and wall roughness and thermal properties upon the characteristics of a coal dust explosion. Data from past explosion research will be examined and assessed for its application to the problem along with theoretical considerations for these factors.Recommendations on the design and minimum appropriate size of explosion galleries for assessing the performance of explosion inerting strategies, passive and active explosion barrier performance and determination of appropriate pressure ratings for ventilation structures will be made.CITATION:Humphreys, D, Collecutt, G, Greenwood, J and O’Beirne, T, 2015. The impact of facility construction and scale on the characteristics of experimental coal dust explosions, in Proceedings The Australian Mine Ventilation Conference, pp 301–308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By A Valero, G M. Mudd

There is active debate and research around the most suitable indicators to assess the sustainability of mining. The most common approach is to report a range of data for a given mine site (or less preferably, a company total), such as inputs, outputs, benefits and potential costs. The most popular protocol in use (and growing rapidly) is the Global Reporting Initiative (GRI). However, these measures are numerous and still do not allow a single over-arching indicator to be developed. Other measures, such as known mineral resources over time, do not account for critical challenges such as declining ore grades, increasing wastes and poorer quality ores or more difficult mineralogy. By adopting a thermodynamic approach to sustainability, through the concept of æexergyÆ, it is possible to incorporate into a single measure the effective quality of mineral resources. Exergy involves the assessment of the minimum energy costs involved in producing a mineral resource with a specific chemical composition and concentration from common materials in the environment. The exergy of a mineral resource is evaluated from mineralogic composition, concentration (or ore grade) and, of course, quantity, by multiplying the unit exergies with the tonnes of the resource produced (or consumed). Since exergy is a thermodynamic quantity (ie energy or joules), it is additive across different minerals, such as iron ore to gold to copper or even oil and gas or coal û making it an ideal indicator to assess mineral resource sustainability at the industry scale rather than the individual mine scale. This paper briefly outlines the theoretical basis for exergy, and then presents a range of commodity case studies showing the application of exergy to the Australian mining industry. Overall, the usefulness of exergy is clearly demonstrated for use as a broad indicator of the sustainability of mineral resources at the national or even global scale.

Jan 1, 2009

By T Ireland, S Eratne, W Newns, P Spies

The approach to risk management during the procurement of major projects often has a significant outcome on the ultimate delivery of a project. The NZ$1.4 B Waterview Connection project is the largest and most complex project yet undertaken by the New Zealand Transport Agency (NZTA) and the procurement process for an alliance contract was refined to provide compliance with the International Tunnel Insurance Group (ITIG) Code of Practice for Risk Management of Tunnel Works (TCoP). The principle of shared risk within an alliance incentivises a common understanding of project risks prior to finalising the alliance agreement and therefore enables superior risk management through design, construction and beyond. Risk management practices need to be instigated well in advance of commercial phases, so that commercial competition does not lead to a significant elevation of project risk. In particular the practice of gaining commercial advantage by taking on a potentially unmanageable level of risk is one of the outcomes to be avoided by the TCoP.During the procurement phase the NZTA placed high value on design and construction mitigation measures proposed in order to address ground risks, as is appropriate for a major tunnel project. In order to achieve alignment on the level of geotechnical risks an Alliance Geotechnical Baseline Report (AGBR) process was developed.This paper describes the measures taken during the procurement process to achieve certainty with respect to outcomes and minimise project risks whilst also achieving value for money. Refinements to the procurement process to ensure compliance with the TCoP prepared by the International Tunnel Insurance Group (ITIG) are described along with the AGBR process applied as part of a suite of measures to achieve a successful procurement outcome.CITATION:Ireland, T, Spies, P, Eratne, S and Newns, W, 2014. Risk management and use of a geotechnical baseline report for a competitive alliance procurement?process, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 553–562 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By S Mundell, J Armstrong, M Evans

"Automation is a common goal within the coal industry for reasons such as efficiency, reliability and sustainability. However, it requires standards and frameworks so business systems can communicate effectively. Automation of sample analysis processes has been difficult to establish due to a lack of direct business system communication between commercial laboratories and mining companies. This has resulted in manual procedures that have contributed to problems relating to analysis instructions, sample identification, results formats and visibility of status.These problems result in loss of data and confidence in data validity, loss of process efficiency and inability to react to issues. An Australian Coal Association Research Program project (Evans, Armstrong and Arboleda, 2014) has addressed these issues through the Coal Quality Data Exchange methodology for direct business system communication between coalminers and commercial laboratories to optimise the transfer of coal quality data.The benefits to the coalminer of the framework are:increased clarity and auditability of what is being sent to the laboratory and what was requestedreduced potential for error introduced through manual transcription tasksincreased speed of loading of analytical results to the customer Geoscientific Information Management Systemimproved turnaround time for analytical resultsincreased knowledge about what took place in the laboratory with respect to the determination of the analytical resultsincreased visibility of the status of a ‘work order’. The benefits to the technology companies and commercial laboratories is a common framework on which to build a sustainable solution that gets away from the multitude of formats catered for today and time consuming manual processes. The common framework significantly advances the future possibilities for the automation of sampling and analysis processes in a production environment.CITATION:Armstrong, J, Mundell, S and Evans, M, 2014. Automating communications between laboratories and mines – a case from the coal industry, in Proceedings Ninth International Mining Geology Conference 2014 , pp 351–360 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 18, 2014

By H Esterhuizen

The Ernest Henry Mine (EHM) in Queensland, Australia is a Sub-level Caving operation that started production below the previously mined open pit at a depth of 535m. Current Production mining has progressed to a depth of 730m, with planned production mining to extend down to at least 1000m below surface. The inclined nature and geometry of the orebody combined with geological structures provides for challenging mining conditions. Over several years, Ernest Henry Mine has introduced measures to improve outcomes based on observations, monitoring and data analysis. As mining progresses deeper, EHM will continue to proactively take steps to ensure future outcomes are anticipated and mining can continue safely and uninterrupted. The focus of this paper is on the changes in seismic- and stress-driven behaviour of the rockmass experienced at EHM, the ground control measures implemented, and the anticipated future conditions and controls required. CITATION:Esterhuizen, H, 2018. The evolution of seismicity and ground control measures at Ernest Henry Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 20–41 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By M J. Thurley, M Wimmer

To assess the present-day functionality of large-scale sublevel caving at LKAB Kiruna a comprehensive measurement program was undertaken involving blast function, fragmentation and gravity flow. As part of this assessment, a fragmentation measurement trial was performed based on 3D imaging of the drawpoint and corresponding bucket load of the underground load-haul-dump (LHD) excavator. 3D image data from stereo photogrammetry was collected and an automated image analysis strategy developed. A number of data sets were collected for each of the drawpoint and LHD bucket, along with sieving results for four of the LHD bucket loads (totally about 70 t). Two of the sieving results were used to inform the automated image analysis strategy, and two were held back as a comparison. Large variations in the visible particles are apparent when comparing corresponding drawpoints and LHD buckets highlighting the impact of sampling location and the need to measure large quantities of data in order to avoid bias from small samples. The results show that 3D imaging and analysis can produce fully automated measurement and analysis of the visible particle size distribution. Although this is not the same as the sieve-size distribution it provides useful estimation of both the larger size classes and a bulk estimate of fine material below approximately 60 mm. The 3D stereo photogrammetry measurement system used produced very high 3D point density but this was achieved using a custom up-sampling technique which significantly smoothed the data, removing small particles, smoothing edges, and this negatively affected the particle delineation algorithms.CITATION:Thurley, M J, Wimmer, M and Nordqvist, A, 2015. Blast fragmentation measurement based on three-dimensional imaging in sublevel caving drawpoints and underground excavator buckets at LKAB Kiruna, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 763–774 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By T Leidich, M Van Zyl, H Lacy

Mining ‘as usual’, until the most recent decades has resulted in limited landform planning and a general lack of mine waste landform design. Material characterisation, mine planning and dedicated professionals undertaking these tasks were rarely available or in place at the majority of mines. This has led to landform instability, erosion, sediment and poor quality water emanating from mine landforms. In many cases rehabilitation and reclamation failed and these sites have ‘landform features’ that are difficult to relinquish or leave and have little or no apparent land use. In many cases mined landscapes around the world have resulted in a less functional and degraded environment, with deleterious impacts on surrounding ecosystems.This situation is now slowly being addressed, as global companies, academics and practitioners and their organisations have started to exploit the ideas from an integration of earth sciences and mining through the application of planning software dedicated to the design of landforms.This development has had its genesis primarily in the United States. We suggest that process has been driven, in recent decades, by the application of resources in response to the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), (USA Congress 11 December 1980) and other mine reclamation legislation enacted by federal and states regulators in the USA. The combining impact has seen a huge transfer of capital back from the public purse and ‘potentially responsible parties’, into abandoned mines to affect control, remediation, and reclamation/rehabilitation of those mines.Given this investment in rehabilitation and reclamation, people engaging in the business of landform planning have had the opportunity to address landform reclamation of historic and active sites. The skills of engineers and scientists with improved technology, waste rock characterisation and modelling tools have been combined resulting in the evolution of landform design and in mine planning of active mines. This has delivered cost-effective, sustainable mine closure designs for over 30 years. Integration of mine design with an understanding of geomorphic principals and the natural landscape, coupled with waste and soil characterisation, yield a positive result. Recently work has been applied across large and small-scale projects by companies. As these processes develop, ideas and concepts are evolving that active mines, or mines in the early planning stages, could use to help reduce double handling, and in the long run reduce overall project and closure costs, more effectively attain the desired final land use, and enhance the industry’s reputation and licence to operate.CITATION:Leidich, T,?Lacy, H?and Van?Zyl,?M,?2014. Application of design concepts and engineering controls necessary to deliver well-designed and rehabilitated landforms, in Proceedings Life-of-Mine 2014 , pp 55–66 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By J J. McNee and, J Crusius, T F. Pedersen

The use of water covers is a globally-applied method for minimising acid rock drainage (ARD) and metal leaching. Although the subaqueous disposal of potentially acid-generating materials has been shown to effectively limit ARD, under certain scenarios, metal remobilisation can occur at circum-neutral pH. The following paper presents data from four case studies in which metal mobility from submerged mine waste resulted in degradation to water quality in the overlying water cover. Subcentimetre resolution profiling of dissolved constituents across the tailings-water interface (dialysis arrays), in conjunction with mineralogical information, were used to elucidate the controls governing metal mobility. The data illustrate four pathways of metal remobilisation, including: the release of zinc via the oxidative remineralisation of metal-rich organics at the tailings-water interface; enhanced remobilisation of arsenic as a result of anthropogenic eutrophication; the release of copper resulting from the pH-driven dissolution of treatment sludges; and the release of radium from uranium mill tailings due to the dissolution of radiobarite [(Ra,Ba)SO4] by sulfate-reducing bacteria. The results highlight the conclusion that the chemical stability of submerged tailings reflects both: the solid-phase characteristics of the tailings material; and the physical, chemical and biological characteristics of the depositional environment. In particular, the data illustrate that rigorous characterisation of both the waste solids and receiving environment must be performed in order to assess their compatibility. The results have relevance to the management of tailings repositories including constructed impoundments, pit lakes and natural lakes.

Jan 1, 2003

By A Scott, A C. Torrance

Explosive properties are typically summarised on manufacturers’ technical data sheets. The values most commonly referred to are the density of the explosive, the energy it is expected to release and its velocity of detonation (VOD). This information is provided so that blasting engineers can make a considered selection of the most appropriate product for a particular blasting application. As an example, a lower VOD and energy product is better suited to blasting in soft, weathered material. In contrast, blasting hard, competent material generally requires a higher energy product which is usually characterised by higher VOD and energy.A review of the technical information supplied by manufacturers shows a wide range of methods of reporting both VOD and energy. A meaningful comparison between products from different suppliers is almost impossible to achieve based on these data. For a similar product, one supplier may have a VOD range of 2800–5800 m/s and a relative bulk strength of 1.34 while a corresponding product from another supplier is quoted with a VOD range of 3100–6300 m/s and a relative bulk strength of 192. In the end, the user has to rely on the level of confidence available from their experience using a certain type of explosive in the type of rock to be blasted at that mine.This paper reviews some of the technical and supporting information that is freely available in the literature and attempts to provide some clarity as to what the numbers that are reported actually mean for the end user. An alternative approach to the evaluation of the suitability of a given explosive to blast a given rock mass is proposed.CITATION:Torrance, A C and Scott, A, 2015. What is relative about energy?, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 447–454 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By L Kormos, V Lawson, G Hill, G Marrs

"In sulfide nickel deposits throughout the world, pentlandite and pyrrhotite are commonly found together along with varying amounts of chalcopyrite and platinum group minerals (PGMs). The mafic or ultramafic host silicates associated with the sulfide mineralisation commonly exhibit a complex assemblage of magnesium bearing silicates, many of which themselves contain significant nickel. Four types of ore are proposed, each presenting their own processing challenges. These are: economic grades of Ni, Cu and PGE (platinum group element) in a pyrrhotite-bearing sulfide deposit, with low pyrrhotite to pentlandite ratios  economic grades of Ni, Cu and PGE in a pyrrhotite-bearing sulfide deposit, with moderate to high pyrrhotite to pentlandite ratios uneconomic high pyrrhotite: low tenor deposits low-grade low sulfide, high MgO ± PGE deposits that can sometimes be economically mined and processed.The grades and recoveries of nickel concentrates produced from sulfide ores can be significantly impacted by the ore mineral texture, the nickel tenor of the sulfides, and the polytype of pyrrhotite which may be either hexagonal (non-magnetic) or monoclinic (magnetic). The mineralogy of the silicates is also of great importance, especially the magnesium silicates and those which tend to produce particles which are asbestiform or which affect slurry viscosity. Other magnesium silicates such as serpentine carry nickel in solid solution, limiting the recovery entitlement of nickel by flotation because serpentine is not amenable to sulfide flotation mechanisms. Differences in plant flow sheets and reagent assemblages are required to effectively separate these minerals.Experience from a variety of plant operations and from extensive flow sheet development programs are discussed. Examples are given of where significant improvements in nickel circuit performance can be made by adjusting plant physical processing conditions or process chemistry to compensate for measurable ore properties and characteristics.CITATION:Lawson, V, Hill, G, Kormos, L and Marrs, G, 2014. The separation of pentlandite from chalcopyrite, pyrrhotite and gangue in nickel projects throughout the world, in Proceedings 12th AusIMM Mill Operators’ Conference 2014, pp 153–162 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 1, 2014

By T Roberts, D Faulkner, G Watt

Traditional mechanised resin rock bolting in hard rock underground mines requires the installation of resin capsules into a pre-drilled hole prior to the rock bolt being spun into a hole to mix the resin and set the bolt in place. In poor rockmass conditions, especially at depth or in highly altered faults and shears, the condition of the holes often deteriorates as the poor ground around it unravels and falls into the hole. This results in partially or fully blocked holes that either damages the resin capsule when they are being inserted into the holes or prevent it entirely until the hole is continuously cleaned of debris. This deterioration of the hole condition, and continuous need to clean and re-drill holes, also increases the diameter of the hole which in turn affects the continuously mechanically coupled anchorage mechanism of the rock bolt to the rockmass as there is simply not enough resin in the hole to fill the annulus between the bolt and the rock. This results in a large increase to critical heading cycle time and, more importantly, results in the rock reinforcement not performing as per design specification and increases the risk of instability. To overcome the quality control issues with resin bolt installation in poor ground, a single pass drill, install, inject and tension self-drilling resin bolt application was designed and implemented for use in such conditions. This system allows the operator to inject a two part polyester resin through a self-drilled hollow bolt to mix and fully encapsulate the rock reinforcement. The self-drilling bolt allows for post injection of the hole after the bolt has been installed into the rock and gives the operator manual or automated control on the amount of resin used in the hole to ensure complete encapsulation and continuously mechanically coupled anchorage to the rock. This allows the reinforcement to work as designed and provide the Geotechnical Engineer extra quality control confidence in these conditions. The implementation of this single pass resin bolting system resulted in significant decreases to the resin bolting cycle time and rock bolt quality control failures. In this paper the design, implementation and embedment into the development cycle will be discussed and the in situ quality control checks used to validate the increase in rock bolt installation quality will be shared. CITATION:Watt, G, Roberts, T and Faulkner, D, 2018. Single pass drill, install and inject self-drilling resin bolt application in poor ground, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 323–343 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

I once read an æarticleÆ in FHM Magazine entitled æThe Coolest Jobs There Ever WasÆ. It was about a group of guys who were pursuing careers that any person on the planet would just kill for. I distinctly remember drooling over the pages, thinking how much I would love to be Michael SchumacherÆs Chief Engineer at Ferrari, or the Principal Designer and Tester for one of the big Dutch rollercoaster companies. From that moment on, I decided that I wanted a career that was cool enough to make it into the pages of that article. Throughout my time at university, I always had that article in the back of my mind. As a result I constantly wondered about what sort of job I could end up with once I left university. More importantly, I wondered if FHM would be banging down my door to put me in the magazine! After a long and stressful job hunting process (in between completing a thesis and studying for exams) I finally managed to land myself a job with Orica Mining Services. I can honestly say I didnÆt know what to expect when I first joined Orica. Most of my friends ended up working for big mining companies, while I was offered a position with one of the biggest suppliers to these mining companies. However, I had a feeling when I was discussing the role with my future supervisor during the interview process that the job was going to be awesome. I have now spent a year working for Orica and I absolutely love it! While I feel that my job is worthy of being in that FHM article, unfortunately, I donÆt think I am going to get my opportunity to be in the magazine. Apparently I donÆt look too good in a bikini! However, I would love to have the opportunity to discuss the journey that I have taken so far û from my time as an environmental science graduate, then moving on to mining engineering, to now, being part of the Orica Mining Services Graduate Program. My suggestion is to use this paper as a resource. I have learnt during my time at university, as well as my time in the workforce, that the best people you can learn from are your peers. Take what you feel is relevant from the paper; hopefully it will help guide you in shaping your own career.

Jan 1, 2005

By J F. C L Costa, J C. Koppe

It is recognised by the major international codes that resource classification involves the interaction of numerous qualitative and quantitative criteria such as data quality, geological and grade continuity, etc. However, the difficulty in quantifying the degree of uncertainty associated with mineral resources estimation has led to the creation of a large suite of methodologies, terms and definitions, with almost every mining company having its own set of standards. It is also intuitively known that several traditionally used methods to evaluate resources do not take into account the spatial continuity of the grades, being unable to provide a reliable measure of the error associated with their estimates. Since they do not provide an error assessment, these methods are inappropriate to assess local or global uncertainty associated with an estimate. Faced with these problems, this work aims at developing a methodology for either quantitative or qualitative analysis of mineral resources estimation, through incorporation of uncertainty and the correct definition of the associated risk or error. The proposed methodology includes the development of a software code incorporating all the main classification techniques used by the mineral industry. A comprehensive study about each technique was conducted allowing a comparison of the parameters affecting mineral inventory assessment. A case study was conducted with a typical iron ore deposit data set from the Conceitpo mine of the Itabira Complex in the Iron Quadrangle, Brazil. The results showed the specific limitations of each classification system and the influence in selecting their key parameters, always based on subjective choices.

Jan 1, 2009

By J A. Wells, K G. Thomas, R F. Dewhirst

"One of the contributing factors to the extreme cost escalation in the first decade of the 21st century was the increase in the amount and cost of engineering work that went into studies and projects. Various reasons for this were identified, including unsatisfactory productivity due to a shortage of experienced/qualified engineers, the increased complexity and infrastructure requirements of many projects due to location, metallurgy that is more challenging and increasing environmental and social requirements. These conditions often led to unsatisfactory project results in terms of cost and schedule blowouts and created a loss of confidence – both internally and externally – in the industry’s ability to complete projects on time and on budget.Technical fundamentals aside, the experience and effectiveness of project teams has had, and continues to have, a major impact on project cost, schedule and ramp-up to nameplate capacity and operating parameters. There are unfortunately too many examples of where project teams have not been as effective as they could or should have been, all to the ultimate detriment of the project.Using the authors’ extensive experience on both owner’s and engineer’s teams, this paper discusses some of the main reasons for suboptimal team, and hence project, performance and offers thoughts on how best to build and maintain project teams. The analysis and conclusions drawn are built around the Tuckman model of group development known as ‘forming-storming-norming-performing’, which was first proposed some 50 years ago. Given the importance of good teamwork to project success, understanding how project teams grow and become efficient and productive is an essential part of good project management that should receive more attention.CITATION:Dewhirst, R F, Thomas, K G and Wells, J A, 2016. Building and maintaining effective project teams, in Proceedings Project Evaluation 2016, pp 38–48 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By M Titley, M NoppT

A study on the feasibility of mining the recently discovered Wallaby gold deposit is due for completion by mid-2000. Open pit mining is the favoured method. Determination of the impact of mining bench height on the recovery of ore, including the estimation of dilution and ore loss, is critical to the economics of the operation. Conditional simulation was used to derive a number of gold estimation scenarios within a typical volume of the deposit. These scenarios were interrogated for a selection of mining bench heights and ore block dimensions. The results were reported as a range of grade tonnage relationships and compared to the kriged resource model. This allowed the resource model to be calibrated to a specific mining bench height and ore block size. Once calibrated, more realistic dilution and ore loss values for a number of mining bench heights were calculated from the resource model. These values were then used to determine the economic sensitivity of particular mining methods. The spread of results from the simulations also provided an indication of the confidence in the kriged grade estimates for the different zones of mineralisation within the deposit and highlighted areas of any significant uncertainty.

Jan 1, 2000

By J M. F Clout

Geological, textural and mineralogical classification of iron ores is routinely conducted by mine and exploration geologists on reverse circulation percussion, blasthole cone and bulk samples for grade control, defining ore and waste, determining lump:fines ratio and predicting downstream processing characteristics. Classification is based on physical hardness, colour, streak and other visual characteristics. However, logging is generally restricted to the five to 20 per cent of chips above about 2 mm. This means that most of the sample is too fine to be reliably logged for anything but colour or streak and the textural types must be inferred from other information. A recently developed software package called æRecognitionÆ allows automated identification and classification of iron ore textural types and gangue on a particle basis in polished section down to 0.01 mm using processed digital images. It is not designed to be used as a routine logging tool, but is applicable where higher definition is required at the resource evaluation stage on selected percussion, drill core or bulk samples. æRecognitionÆ processes data obtained after optical image analysis of fine iron ore samples. It contains several parts, like æRecognitionÆ, æCompositionÆ, æLiberation by Total IronÆ, æLiberation by PhasesÆ and æStatisticsÆ, which allow vast and diverse information to be obtained about the iron ore samples being studied. Identification and classification of the textural type of each particle is performed according to the CSIRO-Hamersley Iron Ore Group Classification Scheme. The recognition procedure encompasses a good knowledge of different ore types and a logical knowledge tree, managing fuzzy boundary problems and the potential for a few different ore types in the same particle to be considered. This new technology introduces strict criteria to make the process of identifying particles more objective. Automated recognition standardises the identification procedure and significantly saves time. It enables users without a strong background in mineralogy to perform accurate texture identification. The æRecognitionÆ package has a modern user-friendly interface and Word compatible output. The combination of all the features mentioned makes the package a convenient tool for detailed studies of fine iron ores.

Jan 1, 2005

By D J. Brake

Most mine ventilation engineers are involved in ventilation planning and design in some capacity. Ventilation modelling software used by a competent experienced ventilation engineer is extremely useful in developing good ventilation designs by allowing assessment of a wide range of potential options. Unfortunately, ventilation modelling undertaken by persons who do not have sufficient experience or knowledge usually results in a façade that covers up a fundamentally unsatisfactory design. Ventilation models are produced for a wide variety of purposes including: fault-finding of a problem area in a mine and options analysis for resolution of such problems; a complete review or optimisation exercise of an entire mine’s ventilation system; or a much longer life-of-mine type of study. Models can be intended as the basis for studies with diverse purposes such as primary shaft or airway sizing, primary fan specification, examining re-entry times after blasting, resolving leakage or recirculation, or investigating the impact of fires or underground climate or cooling requirements. The concepts of ‘materiality’ and ‘fitness for purpose’ are essential to developing or using a ventilation model and serious mistakes have been made in wrongly using a ventilation model for purposes for which it was never intended, often because it is simply the most recent model on the mine site. Mistakes at this level often translate into faulty ventilation strategies and inefficient or ineffective use of scarce capital for ventilation projects. Validating a ventilation model is a time-consuming and expensive process and not every model must (or even should) be fully validated to meet the objectives at that time. This paper discusses the application of quality assurance in ventilation planning with particular respect to the ‘basis of design’ (BOD) as well as the standards for validating a ventilation model. It also provides a recommended way of dealing with non-conformances in measured versus modelled values of critical parameters in the model.CITATION:Brake, D J, 2015. Quality assurance standards for mine ventilation models and ventilation planning, in Proceedings The Australian Mine Ventilation Conference, pp 221–228 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By A Gustafson, G Shekhar, P Boeg-Jensen

The amount of material extracted from each blasted ring in sublevel caving mines is vital when deciding the overall mine production target. The orientation of the production drifts is normally perpendicular to the strike of the orebody, and rings are blasted from the hanging wall side to the footwall side in a retreating manner. For an inclined orebody, a given ring will contain different amounts of material based on its relative position along the production drift. This layout creates a distinctive problem with respect to the extraction ratio optimisation along the axis of the production drift. This paper describes the current drawpoint control strategy practiced at LKAB and presents the variation of drawpoint performance parameters along the production drifts. It uses automatically generated data from a bucket weighing system that measures tonnage drawn per bucket, and it classifies the blasted rings into four zones based on their relative position along the production drift. It considers the loading procedure for blasted rings at Kiirunavaara mine and analyses the variations in drawpoint performance along the production drift. The paper finds that although the current draw control strategy is sensitive to ring position along the drift, it could be modified to optimise the final extraction ratio.CITATION:Shekhar, G, Gustafson, A, Boeg-Jensen, P and Schunnesson, H, 2016. Draw control optimisation along the production drift in sublevel caving mines, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 241–250 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016