Search Documents

By P González, J Videla, E Córdova, I Gottreux

Currently, underground mining of deeper massive deposits with lower grades, harder rock conditions in high strength environments, entails difficulties in caving, fragmentation and seismicity of the orebody.So far, the use of preconditioning (PC) with hydraulic fracturing (HF) has shown positive results in terms of seismic response and caving performance, while PC combined with explosives aims to weaken the rock mass, causing an additional effect on fragmentation.In particular, mines commonly referred to as ‘supercaves’, operated by caving methods, have the need to integrate mine to plant processes, where rock fragmentation appears as a key tool. In fact, it implies making mining and comminution processes more efficient to the plant and for mines, it justifies the search of innovative solutions in drilling and blasting techniques to precondition the rock mass. The following paper aims to show the feasibility of numerical blast modelling to weaken the rock mass using explosives, mainly through sensitivity analysis applied to designs to minimise bias and uncertainty in the results. It is shown how the presence of structures, their geometry and in situ stresses influence or interfere with the PC method being used.From the work, it is concluded that better knowledge on the application of explosives weakening allows specialists to strengthen numerical models associated with every design and therefore previously validate their applicability, helping to understand complex phenomena such as the propagation of mechanical waves in non-elastic heterogeneous media. In this sense, it is understood that while there are studies (Sanchidrián, Segarra and López, 2006) showing that the transfer of energy in the rock mass could be even greater in a confined environment, the more competent rock mass and higher in situ stresses interfere mostly on the effectiveness of a technique using explosives.CITATION:Gottreux, I, Córdova, E, González, P and Videla, J, 2016. Preconditioning modelling and explosives effectiveness in block caving, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 683–688 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

At Bulong, the mineralised (>0.8 per cent nickel) ore exists within numerous lithologies, which can and do occur coincidently. It is very important to discriminate between the different host units for estimation purposes, stockpiling and scheduling. This allocation of host unit has relied upon visual interpretation by the geologist recording the information, which can be very subjective by its nature. By using quantified constraints, such as assayed magnesium oxide and iron, the subjectivity of describing the host material of nickel laterite ore is reduced. The constraints permit consistent identification of the various host units, which improves the confidence in the overall estimation and scheduling of the ore.

Jan 1, 2000

By B Murphy, S O’Connell, J L. Heath

In the 1989 best-seller The 7 Habits of Highly Effective People, the author, Stephen Covey, highlights the importance of maintaining not only ‘production’, but also, ‘production capacity’. When operating a modern flotation concentrator, production is often measured in terms of concentrate tonnage, tonnes milled and plant utilisation. There are very few metrics that focus directly on flotation equipment condition in relation to performance, which is analogous to Covey’s production capacity principal. It is evident on many mine sites that flotation equipment condition is not monitored on a proactive basis and that the prevailing culture is to wait for a failure, before addressing an issue.This paper discusses examples of how poor equipment condition can lead to production loss through poor metallurgical performance. Actual examples are given where these problems have occurred in operating plants. An outline is provided on how metallurgical and maintenance departments can work together to protect production capacity and gain more from existing equipment.CITATION:Murphy, B, O’Connell, S and Heath, J L, 2014. Maximising value through maintaining your flotation equipment, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 71–76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By S F. Rogers, P W. Booth

Digital photogrammetry is revolutionising the task of geotechnical mapping of jointed rock masses and has greatly increased in popularity and sophistication in recent years. Modern commercially available digital photogrammetry software systems can provide geotechnical practitioners with a user friendly tool for rapid data acquisition. The data can be acquired remotely from large exposure areas, some of which may be otherwise out of reach due to restrictions on time, access or safety.Photogrammetry is a complimentary technology to discrete fracture network (DFN) modelling because it can provide the large, statistically significant, spatially located geotechnical data sets required to produce the most robust results. It also provides the flexibility to selectively map structures at a range of scales, depending on the focus of the DFN modelling.Integration of the interpreted rock structure data derived from photogrammetry with modern DFN modelling methods really advances the rock engineering process. The ability to generate 3D fracture models driven by the statistical structural data and conditioned to the features observed by the photogrammetry yields a synthetic rock mass on which improved design methods can be applied. The generation of multiple equi-probable conditioned DFN models allows the use of probabilistic methods for assessing kinematic stability, rock block size distribution as well as a range of other applications.CITATION:Rogers, S F and Booth, P W, 2014. Integrated photogrammetry and discrete fracture network modelling for improved rock mass characterisation and engineering design, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 203–208 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By I T. Cameron

The commercial production of copper metal involves a sequence of purification stages. One step of this process eliminates bulk quantities of iron and sulphur from matte Cu2S(FeS to produce blister containing 95.5 per cent copper. This task is traditionally performed in the Pierce-Smith converter, a cylindrical vessel in widespread use throughout the copper industry. Typically, multiple Pierce-Smith converters are arranged along an aisle, simplifying material transfer from vessel to vessel. Materials are moved through the aisle in pots and boats, using overhead cranes. In terms of the overall process, the converter aisle represents a critical processing unitùit contributes significantly to the value added nature of the metal. The aisle is subject to significant process disturbances. Thus, improvements in the operationÆs modes and conditions have a direct impact on process profitability. As with any commercial operation, improvements are always sought to increase process performance. The general approach involves process modelling, followed by an application of control and optimisation theory to this model. The results of such a study are then applied to the real process, leading to improved performance.

Jan 1, 1998

By Q Liu

Open stoping is one of the widely adopted methods in underground bulk mining. In this method, fanned or parallel holes are often drilled from a top sill down to a sublevel in the ore zone and blasted ring by ring into a stope for excavation. A mass stope blast may involve blasting rock from multi-level drift rounds and displacing the muck to specific locations in order to allow safe and easy access for ore removal. This paper presents a strategic mass stope blast that took place at a large lead and zinc underground mine in eastern Canada. The blast consisted of more than 800 holes drilled in six blocks from three different sublevels. The challenge lay in the control of ground vibration and muck movement using precise timing to complete the blasting within 6.5 seconds. During this time span, sufficient voids were created in each level to allow the muck to move from the upper to the lower levels in sequential order across the six mining blocks without bridging. This paper describes stope blast simulations using a discrete element computer code for modeling blast-induced rock displacement as well as the application of electronic detonators. These detonators provided the means to accomplish the desired firing sequence including a drop raise blast at the start of the mass blast. The modelling concept is also described in the paper.

Jan 1, 2005

The Marvel Loch Operations (MLO) plant was treating ores from up to six MLO sources and in addition needed to blend externally sourced ores with its own ores. This presented a metallurgical accounting dilemma, which was subsequently addressed by the design, implementation and testing of an automatic sampling system. The MLO automatic sampler was well designed and has been the subject of previous internal and external reviews. The sampling action is fully automated and the unit is essentially self cleaning particularly when sampling primary ores. The purpose of this paper is to document the rationale behind the design, the specific details of the sampling station, its use for ore purchase purposes and an assessment of the sampling system to meet the needs of the operator.

Mar 1, 2010

By A Bennett, A Peck

BHP has recently constructed a Hot Briquetted Iron Plant at Port Hedland in the Pilbara region of Western Australia. Supply of iron ore fines to the plant is by conveyor from the companyÆs existing Nelson Point stockyards. The conveyor passes under Port Hedland harbour in a concrete segmentally lined tunnel, approximately 1030 m long and with a 5.1 m external diameter. The tunnel was constructed by a Tunnel Boring Machine (TBM) which both excavated the ground and erected the tunnel lining. The tunnel was bored between cut and cover in situ concrete portal structures, the TBM being launched from the Finucane Island side towards Port Hedland town. The alignment required lengthy gradients of 1:6 on either side of the harbourÆs dredged channel, under which the tunnel is bored with a minimum clearance of 8 m.The tunnel is fitted-out with:1800 mm belt conveyor capable of 10 000 tph;walkway along which a specially designed inspection/ maintenance vehicle can run; andtunnel services including power, light, fire detection and suppression communications, water mains for wash down and sumps and pumps for drainage.This paper gives a general overview of the design and construct contract, important aspects of the design and the construction process itself.

Jan 1, 1999

By M F. L Gibson

The issue of flyrock is very important in the operation of all mineral extraction sites that use blasting. Unlike the other environmental effects of blasting, ground vibrations and air overpressure, flyrock is (or should be) a rare event, with severe consequences which may include damage to property, injury or fatalities. These physical consequences are often matched by a loss in public confidence in the management of the operation, mistrust and bad press. In this work a deterministic analysis of flyrock was carried out using the equations of a particle in motion with drag. The solutions to these equations were used to reproduce the curves of Lundborg et al (1975) for the relationship between flyrock boulder size and maximum ejection distance. A probabilistic approach based on Monte Carlo simulation was built up with the analytical model using published data together with local case study material. A typical quarry blast situation was modelled and estimates of safe standoff distances were determined using risk assessment techniques.

Jan 1, 2001

Lihir Gold Mine is situated in a dormant volcanic caldera on a small island off PNG. Not æextinctÆ but dormant. Current ground temperatures are up to 150 degrees Celsius with active geysers in the workings of the mine, pools of boiling ground water adjacent to low-grade dumps and hydrogen sulphide gas emissions. It is a unique mining environment by world standards. This paper will deal with the following issues encountered and managed by the operation:blasting in hot and reactive ground; management of sulphide gas emissions; disposal at sea of all mining waste rock; one dear to all Australian minerÆs hearts û dealing with landowner groups; and unusual human resource issues.

Jan 1, 1999

By P Bourke, S Ronkainen

Since the early days of flotation, process technicians have known that the speed at which the froth is recovered over the lip of the cell has a very direct and consistent influence on the grade and recovery of the circuit. No plant would deny that, even to this day, one of the most important aspects of a process technicianÆs job is ensuring that the froth is moving at a desired and controlled speed over the lip. Unfortunately, process technicians cannot watch the froth throughout the entire shift, as there are always other problems to attend to. A considerable amount of work has thus been done to develop a æsystemÆ that automatically measures the speed of the froth. This measurement would then be used in simple controllers to emulate the steps taken by the process technician in correcting deviations of the froth speed from its desired level. Many of the earlier attempts to measure speed were ineffective, as they were unable to cope with turbulence on the froth surface. The FrothMasterÖ instrument makes use of machine vision technologies to measure the speed of the froth over the lip of a cell at a very high sampling rate. This instrument produces an extremely reliable and accurate measurement of the froth speed (as well as other parameters such as bubble size and froth stability). As we will show, the effectiveness of the speed measurement in controlling the performance of the plant is a testimony to its reliability. Three FrothMasterÖ units have recently been installed on the Cadia Hills Gold Mine in New South Wales (Australia). The objectives of this installation were:to control the mass-recovery of two Tank Cells in series on the same level where differences in the hydrostatic head between the two cells result in the cells pulling inconsistently with respect to each other; control of the concentrate grade (per cent copper) from the first rougher; reduction in the frother consumption in the rougher circuit by monitoring the froth speed. A simple controller was designed to react to disturbances in the same way that human operators react. This was done after consultation with the metallurgists and the process technicians at Cadia. The controller had two functions: Stabilisation: The stabilising controller made use of three manipulated variables (level, frother addition rate and aeration rate) to control the froth speed to a setpoint. Optimisation: The optimising controller adjusted the froth speed setpoint based on deviations of the grade (measured in real-time by the OSA) from a setpoint. The plant metallurgist adjusted the grade setpoint based on information about the ore. The results from a 21-day trial have shown the following:The ratio of concentrate mass-recovery between two cells in series on the same level has been successfully balanced, thereby overcoming problems due to differences in hydrostatic heads. It is possible to control the speed of the froth, in mm/s, to within five per cent of its setpoint using the aforementioned manipulated variables. It has also been shown that, for reliable control, it is necessary to control more than just one variable (eg level or air). The grade of the first rougher concentrate has been controlled to within 0.3 per cent of the grade setpoint for long periods of time, which has important implications for the circuit recovery. The frother consumption has been reduced significantly. This paper will thus show that substantial progress has been made to demonstrate the value of using on-line froth speed measurements in flotation plant control to obtain real financial benefits.

Jan 1, 2000

When I was first asked to give a paper on work-life balance in the mining industry I was both excited and aware of the incongruity of my position. I have never worked in mining operations nor have I had any experience that approximates the on-site lifestyle. IÆm not really an adventurer or a traveller, I prefer writing and research to hands-on activities and IÆve never worked further than twenty minutes away from home. The perspective I offer is thus largely an objective one. I say largely since I grew up in a family where my parents work arrangements involved long-distance commuting; my dad continues to work FIFO at a coalmine in Blackwater until this day. Perhaps my tortoise-like existence is a rebellion against his flighty movements. The analysis I will be presenting today draws together a variety of sources, from member anecdotes and research on FIFO and work-life balance to the popular philosophy writings of a bald Englishman with a French name. I am speaking of the famous writer, Alain de Botton, whose television show æThe Consolations of PhilosophyÆ you may have seen on the ABC. Work-life balance is a term that gets a lot of mileage in corporate brochures and at breakfast seminars. But like many terms that get bandied around in the human resources circuit, from æteam synergyÆ to æperformance optimisationÆ, I am frequently perplexed as to what it actually means. Corporate websites are at pains to emphasise the high priority that they place on the needs of the whole person. Yet in terms of substantive content, a commitment to work-life balance often seems to translate into little more than the option to take a few morning yoga classes in exchange for working a seventy-hour week. As extended work hours have taken their toll, leading to high attrition of professionals across all industries, employers are increasingly expending resources to discover just what lies behind this buzz word. The challenge for companies is to find meaningful strategies to help employees better integrate different aspects of their lives in a new era of work, as employees are sending the message that they are not willing to play work, social life and leisure off against each other in a zero sum game.

Jan 1, 2005

By R McIlwraith, B Breul

"This paper discusses the successful use of bituminous geomembranes (BGMs) in mining applications since their development in 1974. It explains and illustrates the structure of a BGM composite, which is a geomembrane manufactured by impregnating a polyester geotextile with a compound of bitumen, elastomer and filler. Examples of applications of BGMs in the mining industry are also presented in the following contexts.Storage of solid waste: storage of mining waste at mines in Canada heap leach pads in France, Peru, Chile and Turkey at the base of a mining waste landfill in Brazil capping of solid mining waste in Chile and Canada temporary capping of mining stockpiles in Australia (with possible reuse of the BGM for other works).Examples of the application of BGMs for the storage of liquid waste in mining containment reservoirs in Canada, Guatemala and Peru will also be given.For each example given, reasons are supplied that supported the choice of BGMs by the clients and consultants, drawn from the following advantages of the BGM:BGMs have excellent puncture strength, due to the internal polyester reinforcement, as well as excellent ultraviolet resistance. This often eliminates the need for a cushion geotextile or cover soil over the BGM.BGMs have a very long life expectancy, in excess of 300 years, in subsoil conditions (Breul et al, 2004).BGMs can be installed in very harsh climatic conditions. They are suitable for high wind environments as their heavy mass per square metre makes them resistant to wind uplift. The low coefficient of thermal expansion means that BGMs are suitable for installation in mines where very low or very high temperatures are expected. This reduces construction delays and allows for a quicker use of the mining facility.The fact that the BGM can be installed by the mine’s own workforce, after appropriate training from the BGM manufacturer, allows for a more flexible construction sequence on the mine.Ability of the BGM to connect to other materials such as concrete, steel, rock and other geomembranes that may be on the mine site.The technical advantages of a BGM enabled the engineering consultants to prepare solutions for their mining clients that had a lower environmental risk, had a faster completion schedule and were overall a cheaper option than with a polymeric geomembrane.CITATION:Breul, B and McIlwraith, R, 2015. Bituminous geomembranes in mine construction, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 289–296 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 27, 2015

By Chappell B

Backfill in the form of mine waste tailings has inherent problems associated with attaining adequate strengths upon placement. Fines are usually removed to ensure adequate drainage, which lowers the cohesive strength of the fill, leaving the fines to he placed in a tailings darn. Electro-drainage and electro-chemical grouting is examined to investigate its effects on densification and shear strength within a silty clay tailing having low permeability and shear strength. Two separate grouting mechanisms are observed for the iron and silica grouts used. Electro- osmosis is associated with iron grout that deposits within the tailing matrix under a converging pH gradient, and increases the permeability of the tailing. This process initiates cation exchange and causes cementing of the granular contact points between the clays. Electro-phoresis causes sodium silicate solution to deposit silica grout in the voids of the tailings. The resultant effect of these mechanisms results in an increase in cohesion, leaving the void ratio of the iron grouted tailings as it was but significantly reducing the void ratio of the silica grouted tailings.

Jan 1, 1998

By R G. Reddy, A Yahya

The sulfur distribution ratio (Ls) is an expression of the amount of sulfur in slag to the amount of sulfur in molten metal. The sulfide capacities calculated from Reddy-Blander (RB) model were used to calculate the sulfur distribution ratio (Ls). A new Reddy model for sulfur distribution ratio (Ls) was developed for modelling Ls for ironmaking, steelmaking, and secondary steelmaking conditions. Besides calcium oxide, the major component in the ladle furnace (LF) slags is alumina. The Ls was calculated for typical LF slags as a function of temperature and composition. The model calculated Ls values are in good agreement with the experimental and industrial slags data. The extremely low oxygen potential in these furnaces after fully-killed steel is favourable for desulfurisation. For any given slag’s composition and temperature, its sulfide capacity can be calculated a priori. The equilibrium sulfur distribution ratio between this slag and liquid metal in a particular vessel can also be calculated a priori. The Ls for ladle furnace (LF) slags is about twice those for blast furnaces (BF) slags and ten times those of basic oxygen furnace (BOF) slags. The desulfurisation of pig iron in BF and desulfurisation of steel in LF during secondary steelmaking are recommended. Steel desulfurisation in steelmaking furnaces is not effective. Since the model used to calculate the sulfur distribution ratio (Ls) is a priori, it is a useful tool for the iron and steel makers in improving the product quality and optimisation of the industrial furnace operations.

Aug 21, 2024

By M Forbes, R Jeuken

Brownfields geoscience measurement such as drilling and surface geophysics can be costly and it is often difficult to weigh the cost of data collection and processing against the value it unlocks at the time of extraction. This makes it difficult to prioritise geoscience expenditure and find the optimum intensity of geoscience activity across competing assets. There are multiple options for managing resource uncertainty and spatial variability through mine planning and resource engineering such as varying marketing strategy, adjusting stockpile or other infrastructure design and product blending. Consideration of these alongside increased data collection further complicates finding a comparable value of geoscience programs to determine the right blend of geoscience measurement and engineering controls. Concepts similar to Value of Information (VOI) analysis which is applied to strategic planning can be used to estimate the value of geoscience measurement and pit sequencing at tactical planning and operational timescales. This involves the quantification of resource uncertainty and prediction of how it will affect resource extraction. This paper outlines this process and demonstrates its use to prioritise geoscience at BHP Coal Assets. The value of infill drill programs in enabling operational stability is quantified and compared the value of engineering controls like increased stockpile capacity. This study supports that idea that the application of VOI methods to bulk mining at tactical time horizons has potential to inform geoscience planning and resource engineering not just separately, but as part of a unified strategy for managing resource uncertainty.

Mar 22, 2022

By S A. McManus

With the advances in software speed and capability, many of us now are running multiple scenarios on entire models rather than just testing small areas or a few blocks. In the authors experience both the geological and geostatistical academic theory and our rules of thumb, often prove un-useable or incorrect in the real world we work in. The only way to truly validate and tune our models is to complete the entire model and ‘see if it works’. If it lacks some property we were expecting, then we need to find out why and/or run different scenarios to see what changes. This is not always possible with tight project timelines but we find ourselves doing more and more of this sort of thing, and in so doing, understand that every deposit is different and requires its own ‘rules’ to get valid and useful results. For the purposes of this paper, this process is termed Empirical Geostatistics. Take Clayton Deutsch’s ‘all realisations all of the time’ concept a step back. Before you even think of simulating, test the alternate realisations generated by alternate parameters such as different domaining, varying search neighbourhood parameters etc.

Mar 22, 2022

By G Sartor, A Rich, D Grimsey, R Forzatti, M White

An in-depth process model was developed for the pyrometallurgical, off-gas systems and water balance of the Kalgoorlie Nickel Smelter. This model was used to assess plant capacity with changing concentrate grades, increased throughput and tighter environmental emissions under a range of potential future operating conditions. Comparison of modelled results allowed for flow sheet optimisation across a range of metrics including sustainability, processing capacity and costs. Process modelling software, METSIM® (ver 2020.06 by METSIM International), was used to simulate the flash furnace, integrated electric slag cleaning furnace, Pierce-Smith converters, matte granulation, waste heat boiler, hot gas handling equipment, wet gas cleaning plant and acid plant. The METSIM® model was divided into three separate, yet interconnected models: metals, off-gas and water balancing. This allowed for improved modelling efficiency and traceability while minimising manual error. The METSIM® model was supported by inputs from other specialised software. Chemical thermodynamics software, FactSage™ (ver 8.2 by GTT Technologies), was used to establish relationships for the flash furnace fluxing strategy and determine the operating temperature. Arena® (ver 16.0 by Rockwell Automation), a discrete event modelling software, was used to simulate material movements within the aisle as well as Pierce-Smith converter operation, allowing for integration with upstream and downstream systems. A dynamic data exchange (DDE) was used to connect the results of each software package, interfacing through Excel® (version 4203 by Microsoft). The integration between models provided a streamlined approach to test capacity, bottlenecks, water consumption and emissions under a range of operating conditions, enabling a more robust process. Further downstream modelling techniques were used to assess mechanical equipment. METSIM® outputs provided key parameters for combustion assessments using computational fluid dynamics and finite element analysis for the furnace mechanical design.

Aug 21, 2024

By B Murphy, N Strong, J Albrecht

Rio Tinto’s Argyle Diamond Mine has a history of underperformance with delivery of ore from the underground operation to the surface for processing with no real clarity in sources of loss and value. In order to increase underground production performance, the basic concepts of the Theory of Constraints model were applied to the Argyle underground production system. This prompted a revised view on bottlenecks and contributors to value loss and ultimately leading to record breaking mine performance. System loss reporting to demonstrate the best opportunity to drive value, departmental detail to develop tools to identify improvement opportunities and clarity across the team to ensure alignment and clear lines of communication were critical to the project success.

Mar 15, 2021

By H Yuan, H Tian, Y Zhang, Z Wang, C Wang

Submerged arc welding (SAW) is one of the significant metal-joining processes for manufacturing marine vessels, steel pipes, and offshore structures with high deposition rate and engineering reliability. Welding flux serves several essential functions, including atmospheric shielding, arc stabilisation, bead morphology control and weld metal (WM) refinement. Therefore, from a thermodynamic point of view, the focus for flux design and WM compositional/microstructural modification has been placed to elucidating the transfer pathways and mechanisms of major alloying elements, such as Si, Mn, Ti and O during welding. To this end, a thermodynamic model has been established to predict alloying element contents in the WM. Such functions are enabled by the physicochemical properties of the fluxes, which are inherently rooted in the nature of the fluxes. A unique yet systematical investigation, including physicochemical property changes and structural evolution behaviours, has been conducted over the wide range of fluxes applied to actual welding of EH36 shipbuilding steels. Combined with spectroscopic methods, structural behaviours of network formers such as SiO2, Al2O3 and TiO2 and network modifiers such as MgO, MnO and CaO have been illustrated. Viscosity and ionic conductivity have been found to be positively associated with the degree of polymerisation.

Aug 21, 2024