Search Documents

By J Safarian, D Hariswijaya

Treating bauxite residue as an alternative source of metals for iron and aluminium industry is an approach to promote circular economy in metal industries. Reduction of metal oxides with H2-based process is an important step on decarbonisation of metal industry. In this study bauxite residue pellets were prepared and were reduced with different H2-H2O gas compositions at different temperatures which yielded with various degrees of reduction. The bauxite residue pellets were made from a mixture of bauxite residue and Ca(OH)2 powders and sintered at 1150°C. Hydrogen reduction was carried out on the oxide pellets using a resistance furnace at elevated temperatures in controlled reduction atmosphere of H2-H2O gas mixtures which resulted in reduction of iron oxides in the pellets. Unreduced and reduced pellets were subsequently heated to 1400°C to study their smelting behaviour using differential thermal analysis (DTA) and thermogravimetric analysis (TGA) technique to investigate the evolution of phases related to slag formation via smelting. Equilibrium module of Factsage™ ver 8.1 was utilised to analyse results of thermal analysis. It was observed that Tricalcium phosphate-β (CaP2O8), Bredigite (Ca7Si4MgO16), Rankinite (Ca3Si2O7), and calcium alumino ferrite (Ca[Al,Fe]6O10) were formed during thermal analysis as intermediate phases. The initial slag formation for sintered and reduced pellets occurred at 900°C which mainly contains calcium and small amount of strontium component. The slag formation rate increases significantly starting from 1100°C when iron oxides started to form initial molten slag phase which then followed by other oxides dissolution in the system. Gas formation was observed at 1180°C and it was found that the gas to be released from unreduced pellets is O2 meanwhile the gas to be released from reduced pellets is SO2 gas. Gas formation rate for both pellets start to increase at 1280°C when the remaining chemically bonded gas start to be released from the system.

Jun 19, 2024

About 90 per cent of the pre-mining BIF-hosted iron ore resource of the Hamersley Province of Western Australia is of the Phanerozoic supergene martite-goethite type. The remaining ten per cent formed as supergene deposits at ~2000 ¦ 200 Ma, and were later modified by burial to form the Proterozoic martite-microplaty hematite ores. The supergene-metamorphic segment of this general unified model has been challenged by three recently published hypogene-based genetic models for the hematite ores, all requiring meteoric oxidation to produce the ore. The most recent and detailed, by Taylor et al (2001), is based on data from the small Southern Batter and North deposits of the Mount Tom Price mine. The authors proposed that during Stage 1 æoverpressured bicarbonate-saturated basin brines from the dolomite aquifer of the Wittenoom FormationÆ at 150 - 250¦C, dissolved free silica from BIF to produce a stratigraphically thinned, magnetite-carbonate-silicate-apatite rock. In Stage 2, meteoric oxidation of siderite to secondary microplaty hematite + ankerite, and magnetite to martite, at unspecified elevated temperatures and pressures, was followed by carbonate leaching (Stage 3). Finally, during Stage 4, weathering with removal of apatite, produced the typical low-phosphorus, porous martite-microplaty hematite ores of the Tom Price-Whaleback type. However, evidence of both microplaty hematite and martite reduced to magnetite, and of infill silica, apatite, and ferroan chlorite, with late-stage pyrite, in the pore space of martite-microplaty hematite ore, shows that the hydrothermal activity at Mount Tom Price is a post-ore event. Neither pyrite nor ferroan chlorite could resist the oxidation required to form hematite ore. Recrystallisation of microplaty hematite in these infilled zones to a typically coarser form than present in most of the normal ores, is a further supporting factor. A more credible, post-ore alternative to the hypogene genetic model is suggested here. Re-exposure to leaching by ground water of the metamorphosed ore deposits in the Phanerozoic resulted in the partial removal of remnant goethite. Localised modifications in the porous BIF/ore contact zones were driven by exothermic oxygen/pyrite/carbon reactions in the footwall Mt McRae Shale. Cool descending oxygenated meteoric water in the permeable ore horizons, acted as one limb of a thermal convective cell. In the other limb, heated reducing solutions rose through the permeable contact zones, to produce the observed localised modifications of BIF and ore. Expelled silica from the carbonatised BIF invaded adjacent porous ore to form erratic silicified ore zones, and to produce the local quartz vein systems found in the associated overlying BIF.

Jan 1, 2002

By R J. Beazley, M C. Woods

"The International Cyanide Management Code (the Code) is a voluntary industry program for gold miners and associated cyanide transporters and cyanide producers. By becoming a signatory, a company commits to follow the CodeÆs principles and implement its standards of practice.Signatories are required to undergo an initial certification audit within three years and a recertification audit every subsequent three years. Recertification audits evaluate compliance over the preceding three-year period. This approach presents a number of challenges. Golder Associates has undertaken in excess of 75 initial certification audits and 25 recertification audits; more than any other audit firm. This paper outlines some of the challenges identified and lessons learnt from the recertification audit process. Central to the process is the challenge for organisations to maintain commitment to compliance over the full three-year period and effectively address deficiencies or non-conformances that may have occurred during that period in a prompt manner.The International Cyanide Management Institute (ICMI) provides guidance in evaluating deficiencies or non-conformances, which requires consideration of the æcauseÆ, ædurationÆ and æongoing compliance effortsÆ and an assessment of the concept of ægood faithÆ in response actions. Golder AssociatesÆ experience with the recertification process highlights some common deficiencies with Code compliance programs, such as: system breakdowns (leading to ineffective communication between departments or loss of information) exceedance of discharge limits inadequate inspections, maintenance activities and associated record-keeping.Such deficiencies can be attributed to: personnel changes organisational changes or structures management systems (eg integrated or standalone) awareness and interpretation of Code requirements transparency of management decisions with Code implications.We have identified that ongoing programed assessment is an effective strategy in maintaining Code compliance.CITATION:Beazley, R J and Woods, M C, 2013. Cyanide code recertification - the three-year challenge, in Proceedings World Gold 2013, pp 247-254 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 26, 2013

By S C. Dominy

The gravity recoverable gold (GRG) parameter reflects liberated gold or gold-dominated composite particles that can be recovered by gravity separation. Recoveries depend upon mineralogy, in situ particle size and the comminution and extraction method used. Any ore bearing >15 per cent of gold greater than 50 ¦m in size is likely to have a GRG component. The principal characterisation methodology applied is the three-stage GRG (3GRG) test, based on a 40 kg to 100 kg sample. An alternative is the single-stage GRG test (SGRG), which is generally based on a 20 kg sample. Experience has shown that GRG values can vary throughout an orebody, particularly within different grade and/or mineralogical domains. Test programs must consider sample frequency and mass. This study demonstrates the variability of GRG results based on different sample masses. Consecutive underground faces on a coarse-gold dominated quartz vein were sampled taking five different masses from each. Each sample was processed using a SGRG approach. Subsequently, each development round was batched through a small gravity production plant. The results show that the small samples understate the plant GRG and show inter-sample variability. Large samples show less variability and a SGRG closer to the plant GRG. A high SGRG broadly correlates to higher gold grades, more coarse gold and larger gold particles. These results are intuitively correct, but indicate the likely challenges of sampling for gold recovery in heterogeneous systems.CITATION:Dominy, S C, 2013. Variability of gravity recoverable gold values in relation to test sample size, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 293-302 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By R F. G Phelps

The former Gwynfynydd gold mine is located within the heart of the Snowdonia National Park, North Wales, United Kingdom. The black shale-hosted quartz reefs have intermittently produced more than 50 000 ounces of gold since 1863. Its most recent period of operation by Welsh Gold PLC was between 1992 and 1999 when it extracted 10 000 tonnes annually from a total resource base of 180 000 tonnes. A historical mining grade of 15 grammes/tonne was recovered from the Chidlaw Reef on which all production was based. Erratically distributed gold pockets hosted in the footwall zone of a 3 - 6 m wide quartz reef characterise the mineralisation. The gold exhibits a high-nugget effect and as a consequence the accurate determination of tonnage and grade was difficult. Production was undertaken by overhand shrinkage stoping. Due to its location within a National Park certain environmental constraints were placed on the operators. The principal requirement of planning permission was that processing should take place above ground and not involve chemicals. As a result, an underground mill based on physical separation methods was constructed in response to these environmental constraints. Much of the mine discharge is related to the flow of rainwater through the workings from surface openings on the reefs. Discharge from the underground milling facility was enhanced in various metals, particularly zinc, though was reduced to legally acceptable levels using liming tanks prior to discharge into the River Mawddach. The company was required to monitor and treat all water discharged from the mine before it reached the river. The mine closed in 1999, since which time a tip re-processing has continued as part of an environmental remediation and gold supply program.

Jan 1, 2002

By N Kojola, A Vickerfält, J Huss

The possibility of using an acidic autogenous hydrogen direct reduced iron (H-DRI) slag as a basis for vanadium extraction is investigated. For a raw material to be suitable for producing high-quality FeV, the vanadium oxide content should be sufficiently high and the phosphorus oxide content in a tolerable range. Therefore, the feasibility for vanadium extraction relies on fulfilling two demands: the predominate partitioning of phosphorus to the metal and vanadium to the slag. Correspondingly, the behaviours of phosphorus and vanadium in the Al2O3-SiO2-FeOx-VyOz-P2O5-Fe system were studied experimentally. Slag, 10 g, was put in contact with liquid iron, 30 g, for different durations (2–24 hrs) in closed alumina crucibles at 1873 K. The slag composition was varied between 33.1– 49.3 wt per cent Al2O3, 27.1–46.7 wt per cent SiO2, 16.6–30.1 wt per cent FeOx, and 2.5– 8.8 wt per cent V2O3. The equilibrium phosphorus distribution was 0.42, while the vanadium distribution ranged from 7.6 to 43.4, increasing with the Al2O3- and the FeOx-content.

Jun 19, 2024

By D K. Weatherley, G R. Ballantyne, S Ali, M Yahyaei, M S. Powell

This paper explores development of a novel ore characterisation method for the precise measurement of practical minimum comminution energy. A monolayer of particles with a narrow size distribution is broken using a precision rolls crusher (PRC); an ore characterisation device developed to overcome the shortcomings of conventional tests. For energy measurement, PRC uses two shaftmounted rotary torque transducers. These transducers acquire precise torque and angular speed data in response to the load applied to the rotating shafts during breakage events, which is converted into energy. The test progressively crushes feed particles down to final product size in many controlled breakage stages. The generation of fines in each breakage stage is then plotted as a function of input energy. The inverse of the gradient of this plot provides the size specific energy (SSE) in kWh/t of material generated below a predefined marker size; -75 μm in this case. The PRC has potential to evolve as a geometallurgical ore characterisation test—it is simple, fast, requires small sample mass (200–300 g), covers a wide feed particle size range (10 mm to 115 µm), and provides ideal SSE measurements that can be used for the calibration of on-site production equipment.

Aug 24, 2022

By F Diaz, G Hovestadt, B Friedrich, D Latacz, M Sommerfeld

The metallurgical sector significantly contributes to the global carbon footprint and encounters the challenge of developing more sustainable production methods. This study introduces novel approaches aimed at reducing CO2 emissions within the industrial sector, some of which have been developed up to the demonstration scale. In two case studies, urban waste from the agricultural sector (corn, olives, coconut etc) and waste electrical or electronic equipment (WEEE) recycling residues (shredder light fractions (SLF)) were subjected to thermal treatment. The resulting materials were then used as substitutes for conventional fossil-based reducing agents in both the copper and ferroalloy industries. Furthermore, hydrogen was employed at different scales to assess its efficacy as a reducing agent for recovering metal oxides from fayalitic copper slags. Our findings reveal promising prospects and defined specific challenges for the integration of these alternative reducing agents in the industry. The synergistic use of pyrolysed SLF, bio-coke, and hydrogen presents a viable pathway to significantly diminish CO2 emissions while simultaneously improving the sustainability of the metallurgical sector.

Jun 19, 2024

By Jankola W. A, Delong O. J

Historically, the silica content of zinc concentrates treated at Cominco's Trail Operations has been low. Silica in the roaster calcine seldom exceeded 1.5 per cent because of the low silica content of concentrate from Cominco's Pine Point mine. With the shutdown of Pine Point, alternate sources of concentrate were required and it was anticipated that calcines containing greater than two per cent silica (with excursions above three per cent) would have to be treated. Previous experience indicated that the existing leaching circuit could not tolerate such high levels. Therefore, a research program was undertaken to identify the key factors affecting silica precipitation; to compare different process alternatives; and to make recommendations for modifications to the existing plant. A project to modify and upgrade the leaching circuit has now been completed. Calcines with higher silica contents are successfully treated, but the upper limit of the circuit is unknown. The results of the research work will be discussed and the new leaching plant will be described. Recent operating results will also be presented.

Jan 1, 1993

By S Hapugoda, H Han, L Lu

Charcoal produced from Syzygium Zeylanicum trees was widely used in ancient Sri Lankan iron smelting practices. Charcoal made from Syzygium Zeylanicum tree trunks, branches and leaves were analysed by optical mineralogy and SEM and found to contain unusually high concentrations of calcium oxalate (CaC2O4.H2O – CaOx) crystals in plant cells. Partial and full reduction tests of a high-P Brockman ore were conducted at several temperatures with coke and coke doped with CaOx and CaCO3. It was observed that CaOx promoted reduction and generated comparatively more metallic iron in reduced samples. Furthermore, CaOx encouraged phosphorous partition into slag phases than into the metallic iron, suggesting CaOx can a potential alternative fluxing material to calcium carbonate for treating high-P iron ores in ironmaking processes.

Sep 18, 2023

By H Hoogvliet

The Goondicum Crater industrial minerals deposit is located about 30 km east of Monto, Central Queensland, Australia. Early exploration programs in the 1990s found alluvial ilmenite along the banks of the Burnett River. This mineralisation was traced upstream to the Goondicum Crater. The Goondicum Crater is a topographic feature centred on a roughly circular 6 km diameter layered gabbro complex. Significant ilmenite, apatite, titano-magnetite and feldspar mineralisation are present in a weathered horizon up to 25 m thick. After several drilling campaigns in the Crater and subsequent feasibility studies, the project was developed by Monto Minerals Ltd, an ASX listed company, in 2007. However, the project never achieved production performance expectations and ran out of commissioning funds. The company subsequently went into voluntary administration in August 2008.In 2009, the RMM Capital group, of Brisbane, took control of Monto Resources Pty Ltd, and renamed the company Belridge Enterprises Pty Ltd (Belridge). Belridge commissioned a redevelopment study aimed at recommencing mining and processing operations. As part of the redevelopment study the authors planned a drilling campaign, managed a quality control program and developed a block model. This paper describes the drilling program, analytical procedures, quality control procedures and the preparation of the block model.The block model for the resource estimate was created using 1 m high blocks, wireframes defining the main material types, and 2.5 m thick horizontal search ellipsoids with a radial pattern. The deposit was ‘flattened’ prior to modelling. To assist with the economic evaluation of the project, each block in the model was assigned a net dollar value based on economic parameters provided by Belridge, including anticipated revenues and costs. This modelling technique allowed for efficient investigation of various scenarios and was used extensively in the development and optimisation of the project’s financial model. At a zero net value per block, comparable to a break-even cut-off grade of four per cent ilmenite equivalent, the Indicated plus Measured resource is estimated at 51 Mt, averaging 4.1 per cent ilmenite, 1.9 per cent apatite and 2.5 per cent titano-magnetite.

Oct 5, 2011

By N Schofield

For the sampling of particulate materials in mineral exploration and mining, the fundamental sampling error (FSE) introduced by Gy is a measure of the constitutional heterogeneity of the sample lot and is expressed as the relative standard deviation of subsample grades of a particular mass. The FSE is presently regarded as an important indicator of quality for samples used in resource estimation. Constitutional heterogeneity describes an ideal state of heterogeneity with respect to all constituents of the lot such that the fundamental error among subsamples of a particular mass is minimised.In this paper, the term ‘sampling precision’ used in relation to mineral resource sampling usually refers to a statistic based on the assay results drawn from pairs of separate subsample splits of multiple sample lots. The pairs of splits are extracted after the lots have been prepared by crushing and pulverising to meet specified criteria of grain size and subsample mass. There is presently no generally accepted method of calculating the ‘sampling precision’ from such paired data but some form of the relative standard deviation that is consistent with definition of the FSE is preferred here. The work of Thompson and Howarth in the 1970s on geochemical analytical precision, which has been subjected to extensive examination and criticism by Stanley and Lawie (2007), and that of Francois-Bongarçon since the 1990s forms the background to the discussion in the paper.A significant aspect of the application of Gy’s sampling theory to sampling in gold deposits is the requirement that the fundamental error be maintained at less than ±20 per cent. The most important reason for this is to ensure that the effects of other sampling errors such as the grouping and segregation, and increment delimitation which can cause local and global biases in sampling are kept as small as possible. This paper is focused mainly on the quality of sampling in gold deposits and looks at an alternative to the use of a constant sampling precision applied to a collection of lots with varying average grade. A theoretical model for the FSE based on duplicate sampling is presented and the simulated results of the model are compared to practical outcomes of real duplicate pairs drawn from multiple sample lots. The goal of the work is to present a more informative analysis of duplicate sample data from multiple lots which may allow a more informed view of the potential for bias generating errors during sample preparation and processing.

Aug 22, 2011

Automation in underground mining enhances safety and leads to economic efficiency. In the past many efforts have been made on the automation of longwall shearer operation. With respect to the ultimate goal of automation, ie self controlled operation, coal bed boundary detection is one of the key problems. For longwall human labor is necessary in order to detect the exact position of the coal seam to be excavated. The authors present a sensor concept based on infrared technology and pattern recognition which will solve this problem. The very harsh underground conditions set high demands on the implemented sensors. The combination of infrared sensors and powerful processing algorithms is part of the innovative concept for automation of the new Eickhoff Bergbautechnik GmbH SL 750 shearer loader. The multi-sensor automation system EiControlPlus which is designed for the complete detection of the machine environment fills in the gap in the coal-excavation automation by building a recognition system that turns the shearer loader into an 'intelligent machine' which is capable of detecting the correct position of the seam to be excavated and thus enables human-free coal mining.

Dec 6, 2010

THE ore treated is almost pure copper pyrites (chalcopyrite) in a gangue of quartz and quartz-felsite. Very little free iron sulphide (pyrite) occurs, and at the time of the erection of the flotation plant the stopes in the oxidized zone had been almostentirely depleted. This zone only extends to a shallow depth, and, below the l00-ft. level, the sulphide for the most part is clean and bright but in the crushed and brecciated parts of the ore channel, where surface water has circulated freely, the gangue is decomposed and kaolinized, and the copper sulphide badly tarnished. This class of ore gave considerable trouble at the mill, but unfortunately, was very limited in quantity. A sample of rich ore assayed-Copper, 21.2 %; iron, 24:.3 %; silica, 28.9 %; sulphur, 25.1%.The concentration in the original mill was effected by handpicking, jigging, and tabling. A considerable portion of the copper mineral arrives at the surface in the form of large lumps of very pure quality, eminently suitable for sorting out by hand.The rich ore is tipped over a grizzly at the shaft bins; the oversize hand-picked, and the undersize bagged direct.

Jan 1, 1912

By P W. Wypych, D Curry, A P. Grima

The market has become highly competitive for engineering and equipment vendors, who are challenged to reduce costs while improving efficiency and productivity of mine operations through plant improvements and expansions. Although conveyor transfer systems account for a small percentage of the infrastructure cost of a mine, they form an integral part of the process supply chain. Malfunctions or suboptimal performance can result in substantial financial cost from delayed start-up, unscheduled downtime, reduced throughput and increased maintenance costs.Discrete element modelling (DEM) is a powerful simulation method used to virtually prototype and test the performance of transfer equipment throughout a design cycle. When developed and applied correctly, DEM can provide insight into performance that exceeds the traditional analytical methods, especially when dealing with complex ore properties, behaviour and/or situations.Using case studies sourced from the authors’ recent research and industrial project work, this paper will address the industry goal to increase efficiency and productivity as well as the methods available to the engineers responsible for delivering designs that meet the aims of this strategic approach.The main focus of the paper will be the new calibration technology, which has been developed by the authors to generate DEM material models that are linked to real-world properties and flow behaviours via unique dynamic testing and innovative parameter calibration methods. These calibrated DEM material models can be deployed by engineers into their existing workflows, whether it be for feasibility studies, concept or final design, plant troubleshooting or optimisation.This new technology allows engineers to gain greater insight than that provided by traditional approaches to the design of transfer chutes and other process equipment and also allows informed design decisions to be made that meet industry efficiency and productivity requirements.CITATION:Grima, A P, Curry, D and Wypych, P W, 2015. New discrete element modelling calibration technology to facilitate the increased efficiency of ore handling and processing operations, in Proceedings Iron Ore 2015, pp 449–464 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By C K. Boafo, J Visser

Obuasi Mine in Ghana, with more than 100 years of mining history, developed from a surface operation into a deep >2000 m underground gold mine. The challenge is to extract value from narrow veins left after extensive mining in the wider ore zones of the mine. Since the merger of AngloGold and Ashanti Goldfields in 2004 the mine strives to achieve optimum extraction through an integrated Mineral Resource management process from geological modelling, resource evaluation to mine design and scheduling. The shear hosted gold deposit displays complex secondary shears of variable thickness and continuity. There is an ongoing process of changes taking place in the way that geological modelling and resource estimation is done. Recent developments include the use of computerised systems that support the whole resource management chain from resource modelling to reserve optimisation. The change in thought and technology now allows for targeting narrow veins previously ignored in optimisation and mine design since moving into mechanised mining. The increased knowledge and confidence in the resource models now allows for flexibility in mine design, selection of mining method and scheduling and extraction of the reserves. The focus area for change is the way the orebody is evaluated and extraction designed. Since 2005 major changes were made to the process. This paper considers the historical approach of resource management. It looks at the individual process changes and qualifying the way ahead.

Jan 1, 2008

By G I. Lumley

‘Every mine is a pilot’ is an attitude which encourages the mining paradox of optimistic mine plans and equipment under performance; propped up by an environment lacking accountability. The premise that ‘every mine is a pilot’, appears to underlie the development and operating approach to most mines. It is the hypothesis of this paper that many mining companies, development teams and their managers largely ignore what is done elsewhere. Anecdotally, most planners don’t know whether the selected rates are high or low (rates based on theoretical models tend to be high – certainly higher than what most companies can achieve). Mines then consistently operate the equipment at rates well below targets; often more than 20 per cent below. Further to this paradox, mine performance data demonstrates the average mine is currently operating their equipment at levels of output not much more than half the output of those in the top ten per cent. On the whole mines don’t know the potential of their equipment and therefore don’t put appropriate plans in place to do better. After all, when ‘every mine is a pilot’ there is little reason to look to one’s peers for an indication of potential. This paper will outline why every mine is not a pilot and how mines do value some knowledge, but not as much as they should. This paper proposes a two-pronged approach to address this issue in the area of equipment performance. This approach is to:1. engage in better forecasting of equipment rates and better subsequent performance through benchmarking against industry standards2. provide conditions for more accountability.These parameters are linked and proper implementation of them will address the losses which many shareholders and financiers have incurred when investing in companies with unrealistic mining plans.CITATION:Lumley, G I, 2016. Is every mine a pilot? In Proceedings International Mine Management Conference, pp 75-88 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By M Brockman, M Cowan, A Robeson

"Sunrise Dam Gold Mine (SDGM) is located 820 km from Perth, 220 km from Kalgoorlie—Boulder and 55 km south of Laverton in Western Australia. The SDGM main pit had successfully operated since 1997 and was due to be completed during 2012. An opportunity existed to extract the high-grade crown pillar – 600 kt @ 7 g/t for 135 koz by either open pit or underground methods.The crown pillar was the 60 m (vertically) thick remaining part of the high-grade Cosmo orebody between the top of the paste filled underground mine stopes and the planned base of the final open pit shell.There were two major difficulties being considered when choosing the underground or open pit options:a major wall failure in the upper section of the main pit wall directly above the crown pillar restricting access from the base of the open pit to the top of the crown pillarimpact of a high rainfall event while the crown pillar was being mined from either surface or underground resulting in flooding of the underground mine workings.This paper will discuss the following issues:the process to identify and evaluate the risks in both options using knowledge based modelling software; this technique allowed the evaluation of a complex set of assumptions to arrive at the preferred optionremediation of the Watu failurethe selection of the preferred option and the challenges encountered before, during and after the extraction of the crown pillarthe planning and geotechnical work to ensure the safe extraction of the crown pillarsuccessful outcomes transitioning from open pit operation to a solely underground operation.Citation:Robeson, A, Cowan, M and Brockman, M, 2016. A Case Study on the Assessment, Planning and Extraction of the Crown Pillar at Sunrise Dam Gold Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 115–136 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By J W. Muir, N Bedford

Hong Kong is one of the most rapidly developing cities in the world. With constant population growth and limited opportunities for space, the development of a fast and effective underground public transportation network is essential. Hong Kong’s Mass Transit Railway (MTR) Corporation is currently undertaking several large underground expansions to its existing network. Much of the excavation will be carried out using the drill and blast excavation method.Drill and blast excavation is common in Hong Kong and with the continued development of underground infrastructure the use of the drill and blast excavation method will increase. Although an effective method of excavation, the blasting vibrations caused during construction can have an adverse impact on surrounding structures and impose disruption on the local community.In order to minimise the risks associated with blasting vibrations, and to demonstrate that the impact on local stakeholders will remain within acceptable limits, it is generally necessary for a contractor to submit a blasting assessment report for approval by government authorities before blasting may commence.Continued increases in population density will force more infrastructure to be constructed underground. Tunnels and caverns are increasingly excavated in closer proximity to critical sensitive receivers. This leads to greater potential impacts on the community, tightening constraints on contractors and a higher level of confidence required for approval authorities. Finding a balance between the needs of the community and rising construction costs becomes more challenging.This paper presents a case study on how the blasting assessment report process has been successfully implemented for a major MTR project situated in a densely developed area of Hong Kong. It describes several methods of assessing blasting vibration impacts, innovative uses of blasting for excavation and the mitigation measures employed to provide the best outcome for all project stakeholders.CITATION:Bedford, N and Muir, J W, 2014. Blasting vibration assessment and innovative blasting methods in high-density urban environments, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 9–20 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By P Moser, P Schimek, F Ouchterlony

This paper summarises the findings of 27 model-scale bench blasts in magnetic mortar, which were conducted from 2011 to 2014 at the blasting site of the Montanuniversitaet Leoben.The aim of the study was the investigation of the influence of blasthole delay times in small-scale bench blasts on the face characteristics and cracking damage created in the surrounding rock, which affects the fragmentation in subsequent rows.The test specimens or blocks, which were produced out of magnetite concrete, were roughly 1:100 in scale to normal bench blasts. The confinement of the testing blocks at the sides and back ensured the similarity to normal bench blasts with regard to the wave transmission into the surrounding rock. The specimen contained three or four rows with five blastholes each and were shot row by row, with virgin (undamaged) material in row 1 and increasingly damaged or preconditioned material in the following rows.The tested delay times varied between 0, 28, 73 and 140 µs, which corresponds to 0, 0.4, 1.0 and 2.0 ms/m of burden.The evaluation of the material properties showed that the use of magnetite concrete eliminated the inhomogeneous behaviour of rock, but some unexpected differences of the individual production cycles were still detected.The characteristics of the bench after each blast was evaluated along three horizontal lines out of a 3D model of the bench face. The tested delay time sequences of the virgin (first row) and single preconditioned blasts (second row) produced more overbreak for longer delays, while the third-row shots resulted in a smoothened surface independent of the chosen delay.The introduced damage after every blast was evaluated by an observation of irregularities on the newly blasted bench face. The visible cracks at the top of the testing blocks were documented and divided into several crack families according to their angle, length and origin. The remaining block was broken out of the blasting site after blasting, cut into several horizontal and vertical slices and dye penetrant spray was used to visualise the cracks created. Some of the detected crack families showed an influence of the delay time. The calculated mean crack density and mean crack intersection density showed that longer delays resulted in a higher degree of damage.The fragmentation results were well reproduced by the basic three-parameter Swebrec function. The observed improvement of fragmentation in the second- and third-row blasts was linked to the preconditioning of the burden for the following row while blasting the actual row. With the exception of the simultaneously initiated blastholes, the blasts showed coarser fragmentation for the shortest delays, while the longest delays generated the finest fragmentation.CITATION:Schimek, P, Ouchterlony, F and Moser, P, 2015. Influence of blasthole delay times on fragmentation as well as characteristics of and blast damage behind a remaining bench face through model-scale blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 257–266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015