Search Documents

By Yanske TR, Lane WL

The Doc Run Company and its predecessors have been mining for over 130 years utilising the room and pillar mining method. This method has left approximately 20 per cent of the orebody in the remaining pillars. The original design and planning for the mines did not include extensive pillar extraction. This paper summarises the introduction of the pillar extraction and backfill techniques which have been implemented since 1991. These techniques include the use of low cost fill walls up to 20 in in height and the use of stinger trucks for topping off the fill. In conjunction with these accomplishments, much experience and confidence has been gained in the use of numerical modelling as a method of predicting pillar stability as the mining of pillars progresses. These advances have led to pillar extraction hecoming a major portion of the overall production and have added to the mine life of Doe Run's six operating mines.

Jan 1, 1998

By M Chen, Q D. Gao, Y G. Hu, P Yan, W B. Lu

The safety and stability of construction structures are often affected by blast-induced waves. Investigating the generation mechanism of shear wave (S-wave) during blasting is important, because it has a strong effect in blasting damage. In this paper the generation mechanism and verification of S-wave was studied analytically and numerically. Under the finite velocity of detonation (VOD) of cylindrical charge or the compression wave (P-wave) communicating with the interface of different media during the propagation, the generation mechanism of S-wave was analysed. Propagation of blasting wave in cylindrical charge was simulated with the elastic model, and the generation of S-wave induced by finite VOD was proved. To compare with different numerical methods in simulating the generation of S-wave, the blasting process of instantaneous detonation was simulated by using the elastic model, elastic-plastic model and smoothed particle hydrodynamics and finite element method (SPH-FEM) coupled model. Results demonstrate that the S-wave could not be found in middle section of the charge if the elastic model is employed. But when using elastic-plastic model and SPH-FEM coupled model, the generation of S-wave could be verified. Under the SPH-FEM condition, the amplitude of S-wave is larger and the arrival time difference between P-wave and S-wave is closer to theoretical results.CITATION:Gao, Q D, Lu, W B, Hu, Y G, Chen, M and Yan, P, 2015. Comparison of the generation of shear wave with different simulation approaches, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 79–88 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By H Y. Niu

The coal left in the goaf is easily submerged by groundwater damage. During the mining process of the underlying coal seam, it is necessary to drain the water in the overlying goaf. The coal sample is prone to spontaneous combustion after being soaked in water and air-dried. To explore the effect of micro-functional group transformation of water-immersed coal samples on the spontaneous combustion characteristics of coal samples during the low-temperature oxidation process. Using the experimental method of infrared spectroscopy, the migration law of special functional groups under different oxygen concentrations of water-soaked coal samples was analysed. By means of thermal analysis, the endothermic and exothermic properties of the functional groups in the water-soaked coal samples were studied. The results show that: the higher the oxygen concentration, the more oxygen-containing functional groups in the water-soaked coal sample, compared with the 18 per cent oxygen concentration, the 14 per cent oxygen concentration has a small increase, and the chain length is shortened. The temperature increase together with the oxygen concentration content determines the functional group content, the pyrolysis process produces some functional groups. The lower the oxygen concentration, endothermic rate decreases and endothermic temperature increases, the higher the ignition temperature of coal oxy-combustion, the lower the total heat release, the higher the burnout temperature, and the faster the oxygen-absorbing weight gain and the conversion of functional groups. Below 14 per cent oxygen concentration, the oxidative combustion process will be greatly reduced. The results provide a theoretical basis for preventing long-term water-soaked coal body oxidative spontaneous combustion in shallow buried coal seams.

Oct 12, 2022

By T Walkemeyer, R Elliott, D Chang-Martin

Over the past decade, discrete element method (DEM) simulations have seen increasing adoption by the resources sector to inform the design of materials handling equipment such as transfer chutes, bins and hoppers. But, if ‘all models are wrong, but some are useful’ (Box, 1979) what approaches are available to check that a DEM simulation is useful? How to avoid garbage in equals garbage out. This work considers what properties of bulk solid flow behaviour are important to transfer chute simulation. Cohesive bulk solids (such as sticky iron ore fines) can develop sufficient strength to form a stable cohesive arch, this phenomenon is not well predicted by measurements of angle of repose. This work presents a two-part approach to the development of a useful DEM model that can be used to add value to the design and optimisation of bulk materials handling equipment. Part 1 is the calibration of not just one, but a range of material models chosen to envelope the range of anticipated materials that will be handled. This work describes the DEM simulation of a batch of direct shear cell tests to develop material models that can be measured by the same metrics routinely used to characterise the flowability of cohesive iron ore fines. Part 2 of this work describes systematic methods for validation of the transfer chute DEM simulations. The DEM model is only useful if it can adequately represent the typical problems observed within a transfer chute, such as blockages due to build-up and cohesive arching. Proper validation requires good observations. Validation examples of site observations are shown side-byside with simulations to demonstrate the adequacy of the DEM model and calibration approach. DEM simulations have the potential to add significant value by allowing engineers and designers to predict material flow-through equipment based on a range of material properties, allowing for stress testing designs and making iterative improvements.

Sep 18, 2023

By K Ionkov

The oolitic iron ore reserves in Lisakovsky, North Kazakhstan represent quite a challenging deposit both from a technological and from a resource point of view. The difficulties in processing such types of ore are connected with the extremely fine dissemination of phosphorus and gangue minerals inside the oolitic formations. The goethite crystals are cemented in their structure by aluminosilicates with quartz and other gangue minerals and dissemination is so fine that they are not separable by physical methods. The laboratory tests performed for dephosphorisation show that the combination of alkaline roasting followed by low intensity magnetic separation and acid leaching enables the obtaining of high grade iron concentrate. The magnetic separation performed ahead of leaching is effi cient as a means of buffering the high pH by washing out the soluble salts and the excess of base and after leaching facilitates the removal of secondary liberated gangue minerals in the non-magnetic fraction. As a consequence, phosphorous content is dropped to a more acceptable level for the ferrous metallurgy and iron grade and recovery reach 61.6 and 80.8 per cent respectively.

Jul 11, 2011

By X Tian, J Forster, A Olmsted, E R. Bobicki, M Goldbaum, D Boucher, C A. Pickles

As the global demand for metal values expands, it becomes increasingly important to create more sustainable mining operations. Consequently, considerable research and technology development is required to produce processes which are both more energy efficient and have a minimal environmental impact. One potential technology is the utilisation of microwave pre-treatment to reduce the energy requirements in comminution. Microwaves can preferentially heat the valuable mineral phases in an ore and the resulting differential thermal expansion leads to the formation of microfractures along the grain boundaries. As a result of the preferential heating, ore competency is reduced, mineral liberation is enhanced, a coarser grind size can be employed, and plant throughput can be increased. Furthermore, microwave pre-treatment can be combined with advanced ore sorting, to decrease the quantity of gangue material processed downstream and hence reduce tailings production. Previous studies on the microwave treatment of ores over the last 30 years have mainly been limited to low power bench-scale studies and there is a paucity of information on pilot and/or commercial scale studies. In the present research, the microwave heating behaviours of over 40 ores have been studied at the bench-scale. These results were used to generate a database, from which a unique classification system was developed. This system was used to rank the amenability of any given ore for microwave pre-treatment. This knowledge can be employed to predict the performance of the ores in the high-power pilot scale tests and thus can be used as a pre-screening tool. The effects of high-power microwave pre-treatment on grindability and liberation were reported. Additionally, the ore sorting potential was evaluated using a combination of X-ray transmission (XRT) and microwave infrared (MW/IR).

Aug 24, 2022

By K Verbeken, D Seveno, A Maslov, I Bellemans

Recycling and decarbonisation current metallurgical processes is key for our planet’s future and in both cases, digital twinning will play an important role. However, the various modelling techniques being used for digital twinning require a lot of input values on variables such as viscosities, diffusion coefficients and surface energies that need to be known as a function of temperature, atmosphere and composition, but which are not widely available, such as in databases, for molten slag phases. The need for more accurate data on physical slag properties is clear and will be extremely relevant for making more realistic and quantitative simulations. Some of these properties are difficult to determine, which is inherent to the very high pyrometallurgical temperatures. Therefore, this work focuses on some aspects related to determining electrical conductivities, viscosities and surface tensions of slags via a combined experimental-modelling method. Besides experimental work, molecular dynamics (MD) simulations can be used to investigate oxidic slag physical properties. With MD simulations, one can follow the time evolution of a system (consisting of atoms or molecules) by integrating Newton’s equation of motion. The input for an MD simulation mainly consists of a force field as well as initial positions, velocities and mass of each atom. The determination of the transport properties in existing literature of MD simulations in oxidic systems, is typically based on incorrect assumptions. For example, to determine the ionic conductivity, the frequently-used Einstein-Stokes equation fails to take into account all ionic types and neglects correlated motion. Furthermore, the viscosity determination via the Einstein-Stokes formula also assumes independent motion of the different ions. This paper gives a brief overview of the opportunities and challenges related to the use of MD simulations for oxidic slag systems.

Jun 19, 2024

By J Say, M Hawtin, L Carlon, P Cann

Historically, production from sublevels of the Ernest Henry Mine (EHM) started from blind uphole rises at the end of slot drives. Where previous investigations considered removing these slot drives and starting production with independent ore drives, any development savings were consumed when drives were extended to minimise ore loss. Since 2017, EHM and Orica have been investigating opportunities to optimise drill and blast practices by implementing Orica’s Wireless Electronic Blasting System (WEBS). To reduce ore drive development metres, a novel design was proposed utilising the WebGen™ 100 system to combine a rise with pre-charged widening firings. Initially these new rise and widening firings achieved results similar to previous EHM designs, achieving on average 81 per cent of design height and width. Due to poor performance of the fourth trial a significant re-design was required. Modifications included drill hole re-positioning, in-hole primer relocation and initiation delay adjustments. Since the re-design a step change in rise performance has been observed with rise and pre-charged widening shots averaging 95 per cent of design height and width. With rise and widening performance exceeding expectations, the removal of slot drives has allowed a substantial reduction in lateral development. Development savings of 165 m and 169 m from the RL1325 and RL1300 levels have been achieved. Primary draw and ore recovery has also increased due to the later addition of pre charged forward stripping rings. Level design changes have also significantly improved the mining cycle by allowing for a reduction in required ground support, improved secondary ventilation, a reduction of critical path development, simpler production scheduling and less wear and tear on machinery. Future mine level designs now incorporate key learnings and are proving beneficial to a variety of scenarios including changing orebody boundaries at depth.

Mar 15, 2021

The object of this paper is to give an insight into various metallurgical operations involved in the making and shaping of steel for shipbuilding at the Newcastle plants of the Broken Hill Proprietary Co. Ltd., Commonwealth Steel Co. Ltd. and the Port Kembla plant of Australian Iron and Steel Ltd. Whilst not steelmakers, inasmuch as their processes start with semi-finished. steel supplied by the Steelmaker, the plants of Stewarts and Lloyds (Aust.) Pty. Ltd. and their associate company, British Tube Mills, Rylands Bros. (Aust.) Pty. Ltd. and the Newcastle and Kembla plants of John Lysaghts (Aust.) Pty. Ltd. make substantial contributions to the Australian shipbuilding industry, principally by way of boiler tubing and wires for welding rods and sheet steel, including special silicon lamination sheet for electrical motors.THE MAKING OF STEELThe making of iron and steel began as an accident, slowly developed as an art and has not yet become an exact science. The iron age dawned on the day when, by chance, man's primitive ancestor built up the wall of his fire with ironstone. In the ashes of the fire he found pieces of sponge iron from which he hammered out the first sample' of wrought iron. For many centuries iron ·was manufactured in bloomeries and occasionally, when the temperature was excessive, the iron combined with some carbon and steel was produced. But it was not till '1740 that steel was manufactured under controlled conditions. In that year Huntsman invented the crucible process which held undisputed sway for over a 100 years until in 1856 the invention of the Bessemer process revolutionised the whole industry.From then on, rapid progress was made. The Siemens...

Jan 1, 1951

By Palmer DJ

Mercury is introduced into EZ's electroly tic zinc/sulphuric acid plant complex at Risdon, Tasmania, in zinc sulphide concentrate. Mercury is volatilised during the roasting operation and then distributed in the sulphuric acid plant effluents and product acid. Following an investigation of the factors determining the mercury distribution, a plan was formulated to-provide an environmentally accep- table degree of mercury containment at Risdon. This paper discusses details of the various control measures investigated and out- lines the reasons for selecting the particular procedures finally adopted for the Risdon plant.

Jan 1, 1980

By H A. Challenor

Eyewash safety showers located in remote hot environments may be unsafe to use due to excess water temperature and high risk levels of water borne bacteria such as Legionella. Australian Standard AS 4775 specifies that dispensed water shall be bacteria free and have a maximum temperature of 37.8°C. Legionnaires disease is contracted when water aerosols containing Legionella bacteria are inhaled.Laboratory tests show 30 to 70 times more aerosols are generated by showers operating at 38°C than with showers operating at 25°C. Furthermore, excess temperature in flushing water can cause burn injuries leading to hospitalisation, skin grafts and/or permanent scarring. Excess temperature also increases the rate of reaction to corrosive substances, opens pores in the skin to allow greater dermal penetration and can cause dizziness and fainting by dilating blood vessels and reducing blood pressure.CITATION:Challenor, H A, 2017. Managing excess temperature and high risk levels of Legionella bacteria in eyewash safety showers, in Proceedings Iron Ore 2017, pp 337–346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By R-H Yoon

The thin film pressure balance (TFPB) technique was used to measure the kinetics of thinning of single foam films and disjoining pressures in the presence of sodium dodecyl sulfate (SDS) and electrolyte (NaCl). The results were analysed in view of the Reynolds equation to determine the role of surface forces in film thinning. It was found that film thinning is controlled by surface forces at thicknesses below approximately 200 nm. It was also found that hydrophobic force plays an important role particularly at low SDS and NaCl concentrations. The values of the hydrophobic force constant (K232) estimated from the film thinning experiments were used to predict the disjoining pressure isotherm using the extended DLVO theory, which were found to be in excellent agreement with experiment. The TFPB technique was also used to measure the equilibrium thicknesses (He) of the foam films stabilised by a non-ionic surfactant, n-octanol, in the presence of NaCl. At a given ionic strength, He increased noticeably with increasing octanol concentration at very low concentrations. This observation suggests that hydrophobic force is at its maximum level in the absence of surfactant and decreases with increasing surfactant concentration. The results obtained with the single foam films were used to explain the stability of the three-dimensional foams.

Jan 1, 2005

By M I. Pownceby, N A. S Webster, J Manuel, N Ware

The properties of iron ore sinter – commonly defined by measures of tumble strength, reduction degradation and reducibility – have a major impact on blast furnace performance. These properties are largely influenced by raw material properties, in particular the bulk ore composition. Despite this importance, there is a lack of quantitative data on the impact of ore chemical composition on iron ore sintering. This is surprising since the levels of Fe, SiO2, Al2O3, P, MgO and other elements, together with the nature of the minerals in the fine ore, play a major role in determining the abundance and type of high-temperature bonding phases that form during sintering. It is the abundance and nature of the high-temperature bonding phase(s) that directly influences sinter quality. This study combines in situ diffraction experiments in model sinter systems with laboratory-based compact sinter tests using natural ores to examine the links between iron ore composition and sintering temperature and their effects on standard metallurgical sinter quality test methods. Results help to establish the critical compositional and thermal parameters that control the bonding phase chemistry, which in turn influences the physical characteristics of the sinter matrix. This information should enable operators to predict optimum sinter operating conditions based on the initial chemistry and mineralogy of the iron ore fines and recognise the chemical modifications to the original iron ore fines required to produce high-quality iron ore sinter.CITATION:Pownceby, M I, Webster, N A S, Manuel, J and Ware, N, 2015. Iron ore geometallurgy – examining the influence of ore composition on sinter phase mineralogy and sinter strength, in Proceedings Iron Ore 2015, pp 579–586 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By P Gehrke, S O’Gorman

The precise measurement of NO2 was historically difficult in road tunnels, hence criteria and design analysis was based on converting from NOx concentrations via a set NO2:NOx ratio. The reliable direct measurement of NO2 is now possible, however design analysis is still dominated by emissions tables and formulas specified in terms of NOx. For converting from NOx to NO2 in a road tunnel environment in Australia, the ratio has typically been assumed to be ten?per?cent. This has generally been based on the recommendation in PIARC (2000) and on the ‘average’ value cited in PIARC (1995).Determining this ratio is important as changes in engine technology and in-tunnel pollution criteria along with improvements in CO and particulate emissions control, may mean that NO2 will become the driving factor for future ventilation requirements. Correct selection of this ratio can directly impact the ventilation capacity and system design.Recent research has indicated that choosing a constant ratio of ten?per?cent for all tunnels may not be appropriate. The in-tunnel ratio has been estimated to be as much as 20?per?cent to 30?per?cent and depends on the location in the tunnel, the type of ventilation system and the traffic/fleet characteristics. This paper discusses the effect of some of these parameters on the NO2:NOx ratio in road tunnels.The findings indicate that the ten?per?cent upper limit on the NO2:NOx ratio in PIARC (2000) may be a conservative value for design purposes for longitudinally ventilated road tunnels of typical length in Australia. A value of seven?per?cent to eight?per?cent may be more appropriate in some circumstances. However, the value chosen will depend on the specific tunnel in question and the confidence in traffic conditions expected. Values above ten?per?cent may be encountered for short periods but usually when the NO2 levels are low.CITATION:O’Gorman, S and Gehrke, P, 2014. NO2:NOx ratios in Australian road tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 95–102 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

Knowledge of the crystal chemistry of carbonate apatites is very important for the development of the concept of biomineralisation and the creation of a scientific base for new biocompatible materials for medical purposes. The present work is devoted to research results on various synthetic and biological carbonate apatites obtained at Saint Petersburg University over many years. All-important problems will be considered such as the location of CO32- ions in the apatite structure, the ionic substitutions in various biological apatites and the development of synthesis methods for their analogues. Syntheses of apatites were realised by precipitation methods and under hydrothermal conditions (from solid compounds and by calcite treatment). Biological samples used in this study were physiogenic and pathogenic apatites formed in the human organism, eg in teeth and in renal and salivary stones and dental calculi as well as apatites from fossils of different taxonomic families (brachiopods, conodonts, fishes, reptiles, mammal) with different geological ages and burial conditions. The study of the crystal chemistry of carbonate apatites has been carried out by powder (including high-temperature measurements) and single-crystal X-ray diffraction methods, IR-spectroscopy, thermal analysis and various chemical analytical techniques.

Jan 1, 2008

This paper presents an overview of the current status of mine water management in South Africa. The regulatory framework within which mine water management operates is set out, based on the principles and policies embodied in the relevant legislation. The status of the gold and coal mining industries, with regard to water management, is presented on the basis of studies that have been undertaken to develop water and salt balances for these industries. While the data is not available to quantify the status of ARD in South Africa, the range of typical mine water quality problems faced by South African gold and coal mines is presented. The status quo, problems and challenges relating to mine water management are presented and discussed. It is shown that, while there have been major strides in the last decade, and mine water management and treatment in South Africa has moved onto the forefront of mine environmental management, important problems still persist. There is still a significant amount of improvement required, particularly in the field of prediction of water quality deterioration and the application of such predictions to the identification of management actions that can be applied to prevent or minimise mine water pollution in the shortmedium- and long-term.

Jan 1, 2003

By J Li, J Regan, D Payne

The Caval Ridge Mine is an open cut coalmine and located within the Bowen Basin region in Central Queensland, and commenced mining and processing operations in 2014. A number of geotechnical challenges for managing dragline bench and lowwall stabilities have been encountered in both southern and northern pits over the years. Southern Pits contain steep seam dips of up to 15° (27 per cent) whilst the northern pits also have shears below pit floors. Geotechnical guidelines to manage the risk of dragline bench failure and lowwall instability have been developed and improved since these geotechnical challenges were identified. The dragline guidelines include dragline tub offset distances from the 60° Line (SDL) or buttressing thickness for different seam dips greater than or equal to 8°. The low wall stabilisation guideline established floor disruption widths and depths depending on seam dips and presence of floor shears to known depths of up to 3 m. As mining operations advance, lowwalls have remained stable until floor disruptions were fired, then returned to stable soon after the shot. The maximum distance of lowwall cracking with blasting has been as far back as the second spoil peak (the prestrip truck dumps construction limit). These failures need to be eliminated to allow the operational flexibility and haulage benefit of constructing the prestrip truck dumps behind the first spoil peak, while maintaining no risk to personnel or equipment. The floor shear depth was verified by collaborating with the exploration teams and taking advantage of the already planned 8-inch coal quality core holes, drilling them an extra 5–10 m past the coal seam floor and locating the shear presence. With this continuous improvement effort, no lowwall failures have occurred during floor disruption firing from the second strip after the new floor disruption depth guidance have been applied. This paper documents the processes for developing these geotechnical guidelines, operational implementation, and outcomes. Operational applications over the years confirmed that these guidelines have effectively managed the dragline bench and lowwall failure risks related with the steep seam dips and floor shears in this open cut coalmine.

Nov 29, 2022

By B H. Yin, S Mendoza, M Nusheh' C W Bumby, A Zhang

Hydrogen-direct-reduction of iron ore in a vertical shaft furnace is a potential process that could significantly reduce CO2 emissions from the steel industry. This approach requires the pelletisation of iron ore fines, which then undergo high temperature induration to strengthen the pellets before they can be fed into the shaft furnace. Here we report on investigations into the disc-pelletisation behaviour of New Zealand titanomagnetite ironsand, and its subsequent induration and hydrogenreduction behaviour. Initial studies focused on the effect on pellet strength of varying ironsand particle size and induration conditions using bentonite and a commercially sourced carboxymethylcellulose binder. Green pellets formed with ironsand of average particle size of 65 μm exhibited optimal strength. The compressive strength of these pellets after induration at 1200°C for 2 hrs in air was measured to be 976 N. Interparticle bonding within the indurated pellets occurs due to a combination of titanohematite recrystallisation (from oxidation of titanomagnetite), and the formation of a liquid bonding phase due to interdiffusion with the bentonite and subsequent melting. Further investigation with various binders showed that a combination of both organic and inorganic binders was essential to achieve optimal pellet strength. Carboxymethyl-cellulose binders provides green strength, whilst inorganic binders such as bentonite promoted high indurated pellet strength. Hydrogen reduction tests in a thermogravimetric furnace showed that all the pellets could achieve a maximum reduction degree of 97 per cent at 1100°C, indicating that the different pellet preparation procedures had no significant effect on reducibility. Pellet recipes developed in this work are now being used to investigate vertical shaft hydrogen-DRI processing of NZ ironsand in a kg-scale laboratory reactor.

Sep 18, 2023

By C K. McKenzie

As more and more mining operations around the world either switch to, or trial, electronic initiation systems, the breadth of knowledge and experience regarding their effective application has widened considerably.In South America, for example, there is a strong perception that in order to achieve the finest possible fragmentation, very short electronic delays must be used between successive holes within a row. Limited field studies involving measurement of fragmentation have been conducted to support that paradigm and there are few long term studies which have been strongly supported by measurements of productivity either in the pit, in the plant, or in the leaching pads.On the other hand, some well documented studies have been conducted in North America, showing not only the impact of delay timing on fragmentation but also the effect on semi-autogenous grinding (SAG) mill productivity over extended periods of in excess of 12 months. To date, those studies suggest that optimum timing is considerably longer than the times commonly used in South America.This paper explores the current knowledge of the effects of delay timing on issues ranging from size distribution to vibration impacts in pit walls, to vibration and overpressure impacts in surrounding communities. It also explores how fragmentation modelling can be adapted to reflect fragmentation trends that have been reported in various technical conferences around the world.

Nov 8, 2011

By Tack K

During its 28-year life the MHD ISP smelter has gone through two phases, each of about a dozen years. The first phase was a learning one; in the second phase the lessons were applied and throughput and production rose strongly. Early experience revealed the robustness and the flexibility of the Imperial Smelting Process. The experience was demonstrated by strong increases in the throughput of mixed lead-zinc concentrates and of secondary (oxide) zinc materials. Purchased material quantities rose from 175 000 tonnes/year to 200 000. The required capacity increase of the IS furnace to smelt the higher throughput was achieved by relatively minor modifications; for instance a change to the internal furnace profile gained an extra two square metres in cross sectional area. The furnace hearth area has remained practically unchanged over its entire history. The paper concludes that there is still more potential to be drawn from the process and MHD intends to sustain raw material input at a new level of 240 000 tonnes/year. However, this rate will have to be achieved under the imposition of more stringent environmental and product quality standards than ever before.

Jan 1, 1993