Search Documents

By Victor V. Verbinski

This report presents the development of a raw coal concentration sensor for hydro-transport of coal and refuse (rock) from underground mines, and the results of an international test series carried out at the Colorado School of Mines Research Institute in Golden, Colorado, the U.S. Bureau of Mines, Hydraulic Transport Research Facility in Pittsburgh, Pennsylvania, Saskatchewan Research Facility in Saskatoon, Saskatchewan, Canada, and the Steinkohlenbergbauverein Test Facility in Essen, West Germany. Test results are presented for a three-component sensor and also for the more rugged two-component (all nuclear) sensor.

Jan 1, 1988

By F. du Breuil

BCR National Laboratory (formerly Bituminous Coal Research, Inc.), under a USBM con­tract (originally with the Department of Energy), monitored the installation and operation of a computer-based belt-monitoring and control system at the Barnes & Tucker Coal Co. Mine No. 20, Ebensburg, PA. The system installed was the National Coal Board's Mine Operating System (MINOS) coal transport monitoring and control system. The program objec­tive was to document (1) the installation requirements for a conveyor control system, (2) the operating experience with the system, and (3) the impact of monitoring and control on mine operation. Analysis of the system operation indicates that monitoring and control did improve belt availability significantly, and reduced downtime associated with belt delays. Economic analysis showed the increased belt availability would potentially result in significant production increase, and, therefore, excellent payback on the initial investment. The system performed satisfactorily, was well accepted by the work force, and did not increase the maintenance workload.

Jan 1, 1987

By Leonard J. Prosser, Dennis R. Dolinar, John L. Ellenberger, Gabriel S. Esterhuizen, Anthony T. Iannacchione

The room-and-pillar mining method is used extensively in underground limestone mines in the Eastern and Midwestern U.S. The rock mass is typically a near-horizontal, bedded deposit at relatively shallow depth. A survey of 34 mines was conducted in which data on roof spans, rock mass properties and support practices were collected as part of a National Institute for Occupational Safety and Health research project into ground control in limestone mines. The average room width is 13.5 m (44 ft), accommodating large mechanized equipment. The results show that the immediate roof beam can consist of many individual layers and can contain several near-vertical joints. In spite of the room widths, the roof is naturally stable in many mines. Observed roof instabilities can generally be related to excessive horizontal stresses or unfavorable geological structures that cause block fallout or beam failure of the bedded roof rocks. The survey showed that the rock mass quality of the limestone does not vary significantly throughout the Eastern and Midwestern U.S. Roof conditions and the need for support were found to be closely related to the thickness and competence of the first layer of limestone in the roof. The findings highlight the need to identify local geological structures and the roof beam characteristics so that support alternatives can be evaluated. Monitoring and observational technologies that are available for identifying potentially unstable roof are presented, which include: roof characterization using the Rock Fall Risk Index, automated logging of roofbolt hole drilling, microseismic monitoring and displacement monitoring.

By Victor J. Miller

The Northeast Tripp Slide is one of the larger slope failures that can be attributed to open pit mining. It is a 11.7 million cubic meter (15.3 x l0 6 yd3) wedge failure created by two thick gouge-filled fault zones whose intersection plunges into the Tripp pit at 13°. One unique aspect of this failure is that the slide is now stable despite having moved an estimated 8.5m (28 ft.) towards the pit and having reached a maximum overall velocity of 2lmmlday (0.07 ft/day). The slide started to fail in 1968, accelerated until mining in the slide's toe area was halted in April 1970, then began to decelerate. With the cessation of mining in the toe area, rubblized rock sloughed into the pit bottom which added weight to the failures toe constraints and began the stabilization process. Measurements from a network of survey stations revealed a correlation between the slide's velocity and heavy precipitation. Runoff water accumulating in the tension cracks is believed responsible for this correlation. Moreover, the survey net measurements showed that during the failure's last stage the vertical component of the slide's movement greatly increased. It is proposed that this settling was caused by plastic-like flowage of the clay gouge underlying the failure The fault zone's effective shear strength was estimated by a back- analysis on the wedge's geometry and by performing direct shear tests. The tests, performed on cores taken from samples that were collected on the failure, yielded a residual shear strength of: cohesion 0.61 kg/cm2 (8.7 lb/in2), and a friction angle of 9.6°. This residual shear strength was near1y equal to the back-calculated strength indicating that the controlling fault's effective strength was essentially the same as the residual shear strength of the gouge filling

Jan 1, 1983

By Ronald W. Stingelin

This study undertook the development and implementation of a methodology for estimating the impact of coal seam interaction on the eastern bituminous underground reserve base as published in USBM Information Circular 8655. The effects of previous mining in multiple coal seam areas on currently mined and reserve seams are predicted as a percentage coal loss by an engineering assessment model called the Coal Loss Calculation Model. The model utilizes twelve input variables easily derivable from mine maps or other existing data sources and calculates the effects of subsidence and high-stress due to remnant pillars in the previously mined seam. Extensive literature review resulted in the identification, definition, and quantification of the critical variables of seam interaction. Export opinion surveys were made of mining experts, MESA mine inspectors, and coal mine operators. Statistical analysis was used to establish the redundancy of the critical variables and to develop a total coal loss prediction algorithm. A regional analysis resulted in the production of a series of thematic maps on coal characteristics and distribution. A derivative map showing the areas of commonality within the eastern bituminous coal region served as the basis for implementation of the coal loss calculation model. The model was developed and tested using data from four coal mines in western Pennsylvania and southern West Virginia.

Jan 1, 1976

By H. L. Ramandi, P. Moore

"The corrosion of support bolts in underground mines has become an increasingly prevalent issue over the past two decades. With an increase of premature failures due to Stress Corrosion Cracking (SCC), it is evident that understanding the environmental factor influencing the cable bolt corrosion is critical for maintaining effective ground support hence the safety and productivity of underground spaces. Experimental testing of rock and cable bolts were accomplished in a variety of packings, including saturated clay, saturated coal, mine water and grout/cement to investigate their corrosion behaviours. Water samples were obtained and analysed for pH and electrical conductivity (EC) during the experiment. After a period of 76 days the bolts were retrieved and analysed visually. Primary factors were found to be the presence of geological materials and the aeration of the bolts, i.e. the vicinity to air and air flow, while secondary factors were observed to be pH levels and EC. It was also found that the coal/clay interfaces and the water/grout/cement interfaces are non-relevant to corrosion of rockbolts and cable bolts. The proposed framework can be applied to other reinforcement materials used in underground spaces for improved understanding of corrosion environment.INTRODUCTION Rock bolts and cable bolts are the major reinforcement elements used in mining industry to improve the rockmass properties for safe and productive mining. They are normally used to pin large beams or blocks of rock in underground mines to stabilise the rockmass in the roof (strata) against collapse. The rockbolts are typically low cost hot rolled rebar while cable bolts are composed of strands of wire, normally wound together around a central king wire (Hyett and Bawden, 1993; Vandermaat, 2014). The typical length of the bolts in underground mines is 2.4 m and 4–12 m for rockbolts and cable bolts, respectively (Vandermaat, 2014; Windsor and Thompson, 1997). Cable bolts are much more flexible and usually offer a much higher load capacity than rigid rockbolts. Their increased length and flexibility allows cable bolts longer than the height of a roadway to be used in underground mines."

Jan 1, 2017

By C. B. Manula

This report is volume 9 of an eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment. The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation,' and ventilation. This volume of the final report describes the Water Generator subsystem of the Master Design Simulator. This subsystem simulates the flow of water through a typical watershed-reservoir combination to predict mine drainage quantities in underground workings. The model is a integrated one which handles both the unsaturated and the saturated flow domains as a unified system. The solution of the model is achieved by numerical tech¬niques of finite difference method coupled with finite elements analysis. The Water Generator can be operated either as a free standing model or in connection with the Geology and Reserves subsystem as a part of the Master Design Simulator. A case study is included illustrating the application of the model to actual data. The appendices of the report constitute a user's manual for the program, and include a program listing.

Jan 1, 1975

By Carl Belser

This paper, covering Chaffee, Fremont, Gunnison, Lake, Larimer, Park, and Summit Counties, Colo., is the second of a series reporting on the tungsten potential of the Colorado region. The assembled information was obtained by examination of some properties, personal contacts with owners, and access to unpublished reports by other engineers. The tungsten-bearing areas of the 7 counties cover approximately 400 square miles and are in 10 distinct areas, which vary in size (fig. 1) from 1 square mile up to 290 square miles. The tungsten mineral wolframite was discovered by a man named Hackay near Dale on the Florence & Cripple Creek Railroad in the early 1900's, and wolframite and hubnerite were noted at Climax and the adjacent areas in Lake and Summit Counties at an early date, but no records of shipment from any of the areas are available before World War II. It is not known when scheelite was first discovered, but it was recognized in the Stockton mine during World War I. In the counties listed 64 properties are known to contain tungsten; of these, 18 have had some commercial output, although only 3 of them produced in 1953. The total production through 1953 is estimated at 115,000 short-ton units of tungsten trioxide. In 1953 by far the major portion came from the Climax mine.

Jan 1, 1956

By L. K. Weaver

Bureau of Mines investigated the progressive impact that petroleum (crude oil and condensate) operations in the Gulf of Mexico have had on onshore operations and the expected effect of increasing activities in this area on future petroleum supplies from domestic sources. The data analyzed include capital expenditures, number of wells drilled, success ratio for exploratory wells, daily production per completion, annual producing rates, and oil reserves. The report compares offshore and onshore data and ascertains trends in petroleum industry operations. Observed data and trends indicate that in the near future Gulf of Mexico development and production will continue to increase relative to total U.S. petroleum activity. By 1975 annual oil and condensate production from the Gulf of Mexico is expected to be in the range of 750 million bbl to 1,150 million bbl, and account for approximately 20 to 30 pct of the estimated total domestic production.

Jan 1, 1969

By Ali Porbaha

In today's fast-track construction environment, owners are searching for non-conventional technologies to build their projects faster and safer while maintaining traffic flow during construction. To that end designers and contractors are providing solutions that incorporate many unique features to expedite construction processes. In addition to timely delivery of the finished highway products, there is an increasing interest in making the initial investment in applying innovative technologies and thereby minimizing costly maintenance of highway projects. Accordingly, the aim of this paper (along with the accompanying paper) is to examine innovative technologies, developed mostly in Europe, that accelerate construction of highway, runway and railway embankment foundations. For each technology, a basic concept, installation technique(s), and design considerations are discussed, along with the case history of a real-world project. The Geotextile Encased Columns (GEC), AuGeo, and Continuous Flight Auger (CFA) are presented in Part I. Deep Mixing (DM), Mass stabilization, Cut-Mix-Injection (FMI), and Combined soil Stabilization with Vertical columns (CSV) technologies are discussed in Part II.

Jan 1, 2002

By D. L. King, C. D. Rubert, R. W. Christy, B. A. Schepman

R. W. Christy (Manager of Sales, Sanitary Engineering Equipment, Link-Belt Co.) and C.D. Rubert (Barrett, Haentjens & Co.) — Messrs. King and Schepman have presented an excellent paper which outlines the general practice in the design of thickener mechanisms. Lifting devices, controls, special applications and underflow pumping arrangements have been reviewed in detail. Pumping arrangements were illustrated which eliminate the need for an expensive tunnel beneath the thickener floor. Most of those illustrated have the common feature of a relatively long underflow suction line extending from the hopper floor to the pump located on the bridge at the periphery of the tank. The authors limit these arrangements to comparatively dilute or thin slurrys. It is implied that dense and coarse concentrates, which are difficult to pump, cannot be handled unless a tunnel is constructed. Fig. 1 shows an underflow pump arrangement which negates the need for a tunnel but which permits the operator to convey a heavy dense slurry. The pump is mounted directly on the fixed hoist platform and the impeller is located at the base of the steel center column. Priming water is not needed. The column

Jan 1, 1963

By Boleslaw A. Klosinski

Drilling of a pier hole is accompanied with stress releasing in the surrounding soil and often with loosening of soil at the pier base. In effect the drilled piers are more deformable than driven piles of comparable dimension. The bearing performance of a pier may be considerably improved by properly executed base grouting. Various techniques of base grouting are used; many of them were described by Bruce (1986). The grouting devices are often placed within the pier. Alternatively the soil at or under the base is treated by cement or chemical grout. Preloading of the base subsoil by use of a special grouting cell is considered as the most effective way. Treatment of the ground below pier base with cement or chemical grout may be also useful. It may be performed immediately after the pier construction or during service, as a measure for increasing the pier capacity.

Jan 1, 1995

By Ken Goering, Steve Kral, William Gleason

"Once every four years, the global mining industry gathers in Las Vegas, NV for MINExpo International. According to the show’s organizer, The National Mining Association (NMA), about 44,000 people attended the three-day show from Sept. 26-29. It was a show that featured the latest and greatest in equipment and technology. It also served as the backdrop for a snapshot of the state of the industry and while the picture of a global industry is never completely clear at any one time, one thing that is evident is technology has become a major force in the way mining is done.Had it not been for the awe-inspiring “iron” that was on the show floor in the form of haul trucks and shovels weighing hundreds of tons, one could be forgiven for thinking that they were at the Consumer Electronics Show. From training simulators designed to give a realistic experience of operating mining equipment to virtual reality technology that can take the user into the depths of an underground mine or the middle of a mapped ore deposit, an overriding theme of MINExpo 2016 was that the mining industry is connected like never before.In the north hall of the Las Vegas Convention Center was the GE Mining booth that was designed to showcase its efforts to help create a mine that will be connected from the front office to the face of the underground wall or bottom of the openpit. GE Mining called its booth a digital mine, and it included a suite of technologies that can improve performance, reliability, safety and operations. GE Mining said it views each mine as a mini-city, requiring power, water and transportation. Intelligent, real-time monitoring across the mine allows operators to make data-driven decisions that improve equipment reliability and optimize mine operations for substantial savings. And GE Mining was just one of many exhibitors showing off software that allows various types of equipment to communicate. Its booth sat in the shadow of the Komatsu booth with its new 360-t (400-st) 980E-4 haul truck that included GE’s 360-t (400-st) electric wheel motor. This is just one example of how technology is connecting machines, operations and people around the world and how mining is moving forward."

Dec 1, 2016

By T. S. Smith

INTRODUCTION IN PREPARING this paper for the District 4 Meeting, three factors had to be considered. First, the paper must fit the time alloted; second, it must give a general picture of the geology for those unfamiliar with the property; and third, it must contain some new material in order to be of interest to local delegates. The most comprehensive extant discussion of the geology of the property of McKenzie Red Lake Gold Mines, Limited, is contained in Horwood's report on the general Red Lake area ( 1). This report is the 'bible' of the area, and a general paper on the geology of this particular mine would almost certainly appear to be a condensation of it. It was thought, therefore, that the most suitable procedure would be to base the general outline on Horwood' s report, to extend that outline where possible from information gained since its publication, and finally to leave dangling for the contemplative geologist some of the ideas and problems which ?are currently under consideration. LOCATION AND HISTORY The property of McKenzie Red Lake Gold Mines, Limited, is in Dome township, in the Red Lake mining division of northwestern Ontario. The mine is on McKenzie Island, about four miles north, by water, of the Hasaga mine and old Howey mine.

Jan 1, 1951

By Henrik Saxén, Mikko Helle, Hamid Ghanbari

In this study, a process integration approach in a primary steelmaking is investigated to evaluate future operation concepts of a steelmaking site considering sustainability issues. Mathematical programming is used to study the integration of the steel plant with chemical units for utilization of available off-gases in the system, and carbon capturing and sequestration unit. Different industrial carbon utilization options are considered to find the best route of development. A multi-period optimization model is developed based on site-wide mass and energy balances by considering the availability of the fuels and by-product gases and their consumption in the production system and a conceptual polygeneration system. The objective is to reach maximum economic profit while environmental aspects of integrated system are considered for different fuel systems, alternative blast furnace reductants and implementation of new process technologies. The model can provide useful information concerning techno-environmental and economic aspects for decision-making and can estimate optimal operational condition of current and future primary steelmaking under alternative scenarios. The results of the work illustrate the potential to develop steelmaking towards more sustainable operation in the future.

Jan 1, 2015

By Roger A. Dworak

This report describes in detail the work done on the development of the Time Domain Reflectometry Microcomputer (TDRM). Modifications to the FMC-Model 302A Cable Fault Locator is described in Appendix D. The TDRM unit uses an 8080 microcomputer to accurately locate major faults in low capacitance cables to within ± 1 foot when properly calibrated. Major faults in high capacitance cables are usually located within ± 5 feet. The upper limits of fault detection are <1 kilohm shunt fault and >7 ohm series fault. In practice fault detection limits are reduced to <300 ohms shunt fault and >30 ohms series fault because of discontinuities caused by cable repair.

Jan 1, 1977

By Vhutali Carol Madanda, FHATUWANI SENGANI, François Mulenga

The first introduction of fuzzy theory in the nineteenth century created room for continuous research and application in various fields. Fuzzy set theory has been globally applied in geotechnical engineering, and research in this field continues to date. The fuzzy inference system is considered to be one of the most popular techniques adopted to resolve some of the geomechanical challenges faced in both surface and underground excavations. This paper unpacks fuzzy theory-based approaches in mine geomechanics with the aim of expanding the innovative application of the same approach specifically in tunnel geomechanics. This aim was achieved by conducting a review of recent successful and unsuccessful applications of fuzzy inference systems in underground excavations/tunnelling geomechanics. Indeed, this review has outlined some cardinal points associated with the ability of the technique to solve complex geomechanics problems. However, the success of the technique was accompanied by a few limitations associated with the methodology. Finally, a future outlook associated with the technique has been established.

May 15, 2023

By Andrew P. Jarosz

The present computerized mine planning systems use CAD-like and Data Base Management System (DBMS) environments for the handling of numerical, textural, and graphical data. These two environments are usually integrated, that the data provided by the DBMS are linked to any graphical element rendered by the CAD system. The subsidence monitoring, analysis and prediction process should be integrated with the mine design process. It should allow for the assessment of impacts of mining on surface, surface utilities, and structures. It should also provide for the measures to control mining, that will create only acceptable levels of negative impacts on the surface. The common data base, and graphical capabilities of the CAD interface, may be used with great advantage for both systems. The findings of the subsidence engineering modulus should be directly incorporated into the mine design system, and vice versa. In this paper the author suggests guidelines for the development of the comprehensive computer system, able not only to predict the vertical and horizontal components of the ground movement, but also assess the induced surface damages, and costs related to subsidence prevention and compensation.

Jan 1, 1995

Approximately half of all the fuel energy used in the United states is now pro-vided by oil and natural gas. A persistent and rapid growth in energy demand during the last 3 decades has been absorbed largely by the liquid and gaseous rather than solid fuels. In 1948 the energy provided by coal was substantially the same as in 1920. Meanwhile, the use of oil and natural gas each had increased fivefold. On a per capita basis, the change is more significant. Coal consumption has dropped from about 6 tons per person to 4-1/2 tons, while oil has increased from 4-1/3 barrels to 14-1/3, and natural gas from 7,500 cubic feet to about 35,000. These facts would have only academic interest if the United States had unlimited supplies of all fuels. However, while the Nation&apos;s reserves of coal are adequate to meet our needs for centuries, those of oil and natural gas appear limited. It is obvious, therefore, that the security of our liquid-fuel position would be greatly enhanced if the supply could be based in an increasing degree on solid fuels, such as coal and oil shale, which make up more than 95 percent of our fuel reserves, instead of natural oil and gas. In addition, this would create new employment and help to stabilize the market for coal, which may be facing comparatively bleak prospects in the near future unless its position with respect to other fuels is improved.

Jan 1, 1950

By Srisharan Shreedharan, Gang Huang, Hongqing Song, Sijing Cai, Pinnaduwa H. S. W. Kulatilake

"Subsidence prediction due to ore extraction and backfilling during open stoping operations for an underground iron mine in China is reported in this paper. Geologic complexities including faults and interfaces between different lithologies, and the stoping and backfilling sequence adopted from the mine plans are incorporated in building a 3-D discontinuum numerical model. The stoping was simulated in two vertically stacked horizontal layers (Fig. 6), with a total of 16 stopes. Large displacements of up to 50 cm were predicted by the model along the roof of the stopes, and a maximum surface subsidence of 22.5 cm was predicted by the model . Backfilling was found to control subsequent deformation and subsidence. The extraction of the upper orebody led to relatively higher deformations in extracting the lower orebody. Finally, the predicted subsidences at all locations along a subsidence profile on the surface are shown. INTRODUCTIONThe Luohe iron (pyrite) mine, located in Hefei city, Anhui, is an underground mine in China, being mined through the open stoping and backfilling method. The orebody lies at a depth of about 400 m and has an average thickness of 250 m (Magang Steel Company, 2012a). Discovered in the 1960s, the location has a reserve estimate of 300 million tonnes, which have been mined since 2007. The orebody has been divided by the mining company into an east and a west section to facilitate planning for ore extraction.Figure 1 shows the surface above the underground mine, which is seen to contain many human settlements including villages, pastures and other infrastructure. These locations are sensitive in that they need to be protected from potential adversities due to the underground mining, such as surface subsidence. While it may be near impossible to completely eliminate the subsidence due to ore extraction, operations such as backfilling have been adopted by the mine in an effort to substantially reduce it. Hence, this paper focuses on describing the stability of stopes in the mine and estimates future subsidence in a part of the mining region through numerical modeling."

Jan 1, 2016