Search Documents

By Michael McNinch, LaTasha R. Swanson, Jennica L. Bellanca, Justin Helton

As manufacturers and mine operators develop and implement proximity detection systems (PDSs), they need to be mindful of the systems’ compatibility with mineworkers’ tasks, and possible unintended consequences. Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) interviewed mineworkers at mine sites that currently use or previously have used PDSs on mobile equipment, including shuttle cars, battery haulers and scoops. Mineworkers reported that mobile PDSs affect loading, tramming, section setup, maintenance and general work on the section. Mineworkers discussed the operational effects and increased burden, exposure and risk. Mineworkers also suggested that improved system task compatibility, training, logistics and PDS performance might help address these issues. Manufacturers and mine operators implementing this or similar technologies may also consider mitigating task incompatibilities up front, performing additional site-specific usability testing and restricting the use cases of the system to improve performance.

By C. K. Eilerts

Knowledge of the phase relations of the fluids that exist in the porous spaces of rocks constituting natural petroleum reservoirs and of the behavior of these fluids under various field conditions of operation is essential to the conservation of petroleum and natural gas and to their efficient recovery. The problem of determining whether these fluids axe in the liquid or gaseous state send of recognizing the transitions that may take place as the material in the reservoir is subjected to different conditions of pressure and temperature confronts many producers today, especially in certain fields. The subject has grown rapidly in importance since the discovery of and production from deeper reservoirs that have correspondingly higher pressures rind temperatures as compared with shallower

Jan 1, 1938

By Jaime Herrero, Santiago Gómez, Pablo Segarra, José Ángel Sanchidrián

This paper presents a mathematical model for the study of the 2D movement of blast bench faces based on the high-speed video analysis of three blasts at El Aljibe quarry (Spain) recorded at 2,000 frames per second. In these blasts, a set of bags of 0.75 × 0.75 m were placed in front of a selected blasthole defining a reference plane in which to study the kinematics of the movement. The burdens range from 3.86 m to 5.54 m, with a bench height of 12–13 m. An affine transformation system was calculated to convert coordinates from the video images into actual spatial coordinates. The problem is established from a multi-objective minimization approach in order to simultaneously optimize two defined objectives: trajectory fitting using Total Least Squares regression, and time–displacement regression using Ordinary Least Squares. Muti-objective minimization formulation produces Pareto plots of non-dominated solutions, i.e., optimal combinations of initial velocities and response times, (i.e. time between detonation and the onset of bench face motion). From the Pareto frontier, the most balanced solution is selected. Blast response time lasts only a few milliseconds and appears so brief at the frame rate used that it is difficult to detect visually. In this context, the bi-objective optimization-based approach proves to be a more robust tool than frame-by frame survey for quantifying such a rapid event while also maintaining a strong performance in the trajectory fitting task. Root Mean Square Error (RMSE) for the two minimizations average 0.22 m and 0.13 m, respectively. The initial velocities obtained range from 4 to 17 m/s, and the response times 0.7 ms to 21.7 ms. An analytical model is also presented for predicting fragments initial velocity and response time as functions of blast geometry and rock mass properties, explaining approximately 87% of the total variability.

Jan 26, 2026

By D. Letzig

Wrought magnesium alloys are of special interest as lightweight structural components as a result of their more homogeneous microstructures and improved mechanical properties compared to cast components. Extrusion as a shaping technology offers the possibility to produce a wide variety of magnesium alloy profiles. In this contribution we describe the role of extrusion parameters such as extrusion speed, ratio and temperature as well as the type of extrusion process on the microstructural development of AZ-series magnesium alloys and the resulting mechanical properties. The effect of microstructure on the tensile/compression deformation behavior of the alloys has also been investigated. Aspects of process optimization designed to overcome technical and economic limitations and thus establish magnesium alloy profiles for industrial applications will also be discussed.

Jan 1, 2006

By Xinzhi (Thomas) Du

"A longwall mining method is a productive mining method of coal extraction that involves the complete removal of large, rectangular panels of coal. Since this method causes deformations through the overlying strata to the ground surface, the surface- and ground-water regime above the longwall panels may be adversely affected and drained into the lower strata. The purpose of this study is to determine the effects of longwall mining subsidence on surface- and ground-water systems.This study is a site-specific hydrogeologic analysis conducted before, during, and after panel retreat at a site located over two selected longwall panels in the Pittsburgh coal seam in Greene County of Pennsylvania. Mine subsidence causes fractures in the overlying strata and enlarges bedding plane separations, increasing the effective porosity and storativity of the overlying strata. Generally, the water in deeper aquifers located in the lower fractured zone drains into the mine void due to the vertical fractures. Moreover, the water level does not recover after longwall mining (but may recover when the mine is flooded). The upper aquifers over the thick aquitard layers may maintain the water level or drop slightly during longwall mining and recover very quickly. The reason is that the underlying aquiclude layer has less change in porosity and permeability after longwall mining (Carver, 1994).A groundwater flow model-MODFLOW was used to predict the water table contours for the periods of pre- and post-mining conditions. The hydraulic gradients of post-subsidence became larger outside the panels and smaller inside the panels than that of the pre-subsidence. The groundwater hydraulic heads above the longwall panel dropped a maximum 50 ft in the study panels. The shallows monitoring wells that were less than 50 ft deep from the surface were deeply affected by longwall mining subsidence. For the intermediate wells that were more than 85 ft deep from the surface, where strata movement acted as a unit during longwall mining subsidence, there were little impacts of longwall mining on the intermediate wells in the study area. For the deep wells that were located below the Waynesburg sandstone, the water was drained to the underlying strata or even into the mine gob."

Jan 1, 2019

By R. W. Heckel, H. P. Cheskis, A. Lawley, M. R. Pinnel

THERE are discrepancies reported in the literature regarding the micro and macro stress-strain behavior of metals and alloys. In particular, Young's modulus and micro yield measurements often show significant variations depending upon the techniques employed.'-" The purpose of this note is to correlate measurements made with four techniques and to indicate where some of these discrepancies might arise. Allied use of these techniques can provide a complete and consistent characterization of micro and macro stress-strain behavior (over the strain range of 10-9 to 10--2 in. in.-') from a minimum number of samples. Techniques. The techniques employed for measuring stress-strain behavior involved the use of a) linear differential transformers, b) SR-4 strain gages, c) longitudinal resonance waves, and d) X-ray diffraction. Specimen geometries and preparations are summarized in Table I for each technique. Differential Transformer and Strain Measurements. An Instron universal testing machine, modified with an alignment device, was used to apply the load via parallel-jaw grips. The signal from the load cell was applied to the Y scale of a Moseley X-Y recorder (sensitivity of 10 lb load per in. chart). The elongation was monitored simultaneously with strain gages mounted on three sides of the rectangular specimen, and with two linear variable differential transformers (LVDT) mounted at 90 deg to one another on faces that also contained the strain gages, Fig. 1. The signal from one of the LVDT's was applied to the X scale of the recorder (sensitivity 40 µ in. elongation per in. chart) in order to trace a continuous load-elonga-tion curve. Concurrently, the strain on the same face (i.e., the face monitored by the LVDT) was recorded by the corresponding strain gage. A stress-strain curve was plotted from the load cell-strain gage data and was compared to the stress-strain curve (converted from load-elongation) plotted from the continuous load cell-LVDT trace. Identical Table I. Description of Specimens Used in the Present Study Material Dimerisions Preparation Condition 99.99 pct A1 tensile 318 by 3/16 by 3 in. as cast ingot; cut annealed specimen on diamond wheel 2024 A1 tensile 318 by 3/20 by 31/2 in. vacuum hot annealed specimen pressed sheets; cut on diamond wheel 99.99 pct Al 3116 by 3/16 by 2 in. cut from tensile prestrained dynamic modulus specimen after 10"* in. specimen test per in. 2024 A1 dynamic 3/20 by 3/20 by 2 in. vacuum hot annealed modulus specimen pressed sheets; cut on diamond wheel 2024 A1 X-ray gage section 112 by vacuum hot annealed specimens 1/4by1/20in. pressed sheets; cut on diamond wheel

Jan 1, 1970

By Guilherme L. M. G. Carvalho, Zachary T. Fleming

In a world of 2-dimensional design documents, envisioning and understanding 3-dimensional interferences for complex foundation construction scenarios can be challenging. Videos and computer models serve as 3-dimensional spatial aids but have drawbacks related to a fixed perspective. Augmented and virtual reality (AR/VR) provide new tools to communicate design challenges and improve construction planning. This paper provides a practical look at the basics of AR/VR systems and the tools available to the foundation design and construction industry by giving a high-level example of the technologies’ use in the design and delivery phases of a complex micropile installation project for the remediation of a dam foundation. Using these technologies, GEI was able to design and deliver a complex foundation remediation solution. AR/VR benefited regulators, and the client, to help understand the design concept, construction sequencing, and approach to overcoming installation challenges. Due to its user-friendly nature and less rigorous programming and hardware requirements, AR proved to be more useful than VR for this scenario. AR/VR will likely not replace videos and computer models; however, it can be a useful 3-dimensional visualization aid that complements the project delivery process and offers benefits that traditional methods cannot. INTRODUCTION Augmented and virtual reality is a promising and rapidly developing technology within the engineering and construction world. Like any rapidly developing new technology, the language describing it can be confusing and dynamic. To eliminate the confusion some definitions must be made. AR/ VR definitions The definitions of virtual reality (VR) and augmented reality (AR) for the purposes of this paper are as follows: VR is a computer-generated immersive environment that the user experiences within a digital 3- dimensional space (Satava, 1993)AR is a composite view created by superimposing digital objects into the user’s real-world view (Azuma, 1997). Often, VR is used in an office environment and allows the user to “visit” the digital site to review site planning, construction sequences, and interference geometry. AR can be utilized in both the office and onsite environments. Like VR, the in-office application for AR is commonly site planning. AR also can be utilized in the field for applications such as seeing through the ground to locate known existing obstructions like utilities, gas tanks, etc.

Jan 1, 2019

By Roy A. Grancher

?The Horn of Plenty seems to have sprung a leak?.? anonymous For the first time in the Nation's peace-time history, shortages have become a way of life for the United States. Such words as scarce, tight, and critical are used in regard to supply, leading to priorities, allocations, and possible rationing as make-shift attempts to satisfy demand. Almost every day a new type of shortage appears in another product area that has traditionally been taken for granted as being in perpetual abundance. The range of coverage extends from basic commodities such as oil, chemicals, cement, steel, copper, cotton, etc., through to machine tools, motors, bearings, electronic components, etc. , to those finished outputs that satisfy our fundamental requirements for food, clothing and shelter. Signs of the times appear in cancelled airline flights, unfilled lines at gasoline stations, no available home freezers, lengthy delays in any furniture deliveries, or to that little old lady seen walking out of a local supermarket clutching her hoard of twenty rolls of toilet paper. What a sad commentary to have to make about our Land of Plenty, so long the envy of the World for its material wealth -- and today with its initials "U. S." seemingly standing for ?Unlimited Shortages.?

Jan 1, 1974

By David Ballón Vera

El presente estudio describe la importancia del financiamiento en la industria minera como herramienta de difusión a través de dos condiciones: la primera, es que esta se adecúe a las características de la minería y la segunda, refiere que los mineros replanteen su estructura organizativa de estudios (pre-factibilidad,factibilidad, ingeniería y diseño) para el inicio de una posible inversión, así como preveer que de la experiencia obtenida, se contó con poco apoyo financiero.

Nov 20, 1978

By A. E. Lehmberg

"IT IS KNOWN that some ores of sulphide type, such as pyrite, chalcopyrite, and bornite have an electrical conductivity comparable to that of metals, and accordingly much higher than the conductivity of any unmineralized rock. This physical property has long been used for the detection of orebodies of this kind by means of electrical measurements made at the surface of the ground.The present paper will deal with a new electromagnetic instrument for the investigation of subsurface conductors, which has been recently introduced into field practice and has already led to successful results in Canada.The principle of the instrument will be described. How it operates, and how the observations made can be interpreted will be explained. Field examples will •be shown to illustrate its application.Description of Instrument and of Operating TechniqueThe equipment (1) includes a low-frequency alternating current generator. The a.c. is supplied to a transmitter coil and generates a primary field which induces eddy currents in the ground, the intensity of which is proportional to the ground conductivity."

Jan 1, 1952

By A. C. Losekamp, R. M. Fincel, J. B. Conway

TANTALUM like several other metals exhibits a great affinity for or reactivity with certain gases. Tested in atmospheres which are not completely pure this metal becomes contaminated by certain impurities (notably nitrogen, oxygen, and hydrogen) with a resultant change in various properties. Well-known are the drastic changes in hardness, ductility, and electrical resistivity. Also previously recorded are the distortions of the lattice1,2 accompanying the increased content of oxygen and nitrogen in tantalum. This pronounced affinity for certain gases along with the significant property variations thereby produced makes it necessary to observe additional experimental precautions in making various property determinations with tantalum. Some recent measurements of the linear thermal-expansion characteristics of tantalum have made this point quite emphatically. Failure to observe the greatest precautions in reducing the contaminating influence has led to some extremely distorted results. Not only does such operation lead to different heating and cooling curves during the thermal-expansion measurements, but upon cooling to room temperature the sample is found to have suffered a permanent (actually semipermanent since the specimen can be returned to its original length by a 3-hr degassing treatment in vacuum at 2300°C) elongation. In addition, subsequent heatings will not follow the initial heating curve unless the expansion measurements are based on the actual specimen length at the beginning of the heating cycle. These thermal-expansion measurements were made by positioning the specimen horizontally at the longitudinal midpoint of a 20-in.-long, 4-in.-diam resistively heated tungsten tube furnace. The specimens were in the form of 20-mil sheet formed into a sharp U-shape about 0.3 in. in width and 0.3 in. in depth. Fiducial marks in the form of 0.010-in. holes drilled at either end of the 2.5-in.-long sheet specimens were viewed by a paired filar micrometer telescope system mounted on an Invar bar on the top of the furnace. Tests were made in helium with temperatures measured by a Pt/Pt-lORh thermocouple to 1000°C; above 1000°C temperature was measured by means of an optical pyrometer sighted into a black-body hole drilled into the specimen-holding fixture in the vicinity of the specimen. Previous tests with black-body holes drilled in a 0.25-in.-diam rod specimen had confirmed the temperature uniformity between specimens and specimen-holding fixture in this furnace. A typical thermal-expansion curve for arc-cast tantalum in helium is shown in Fig. 1 for the case where no attempt is made to remove all the impurities from the cover-gas atmosphere. The initial heating curve appears smooth and has a shape characteristic of all metals. However, it is known that the sample begins absorbing impurities at temperatures above 1000°C which are sufficient to distort the lattice and lead to specimen lengths which are somewhat larger than would be obtained in the absence of contamination. During the cooling cycle the expansion curve is seen to be significantly different from the heating curve. This is due to the impurity content causing a semipermanent (i.e., permanent until the impurities are removed by vacuum degassing) deformation which will not allow the speci-

Jan 1, 1965

By Jr. Watts, B. K. Cantrell, D. H. Carlson, K. L. Rubow, S. T. Bagley

"Permissible exposure limits (PELs) have been established for gaseous pollutants, carbon monoxide (CO), carbon dioxide (CO), nitric oxide (NO), nitrogen dioxide (NO2), and some gas-phase hydrocarbons emitted in diesel exhaust. There is, as yet, no PEL recommended for diesel exhaust aerosol (DEA), nor is there a standard method for sampling this aerosol.The University of Minnesota and the U.S. Bureau of Mines have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) which utilizes size-selective inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were made in underground coal mines that use diesel equipment.The mine mean DEA concentrations for the five mines surveyed, determined with the PDEAS in the haulageway, was 0.89 mg/m3, with a standard deviation of 0.44 mg/m3. DEA contributed 52 % of the respirable aerosol at this location.In three of the mines filter samples were collected for DEA-associated polynuclear aromatic hydrocarbons (PAHs) and biological activity determinations. Two of the mines were also monitored for the major gaseous constituents found in diesel exhaust. In general, the PAH and biological activity levels were similar for all three mines, and indicate that up to 25 % of the haulageway concentrations may be contributed by outby diesel vehicles. Measured concentrations of CO, CO2. NO, NO2, and SO2, were well below regulated levels.INTRODUCTIONDiesel exhaust contains pollutant gases, such as carbon monoxide, carbon dioxide, nitric oxide, nitrogen dioxide, and gas-phase hydrocarbons, as well as DEA. Much of the health-related concern focuses on DEA and associated organic compounds (Watts, 1992a). A wide variety of these PAHs have been identified and some are known carcinogens and/or mutagens. The U.S. Mine Safety and Health Administration (MSHA) has proposed new PELs for these and other contaminants (MSHA, 1989). MSHA has also published an advance notice of proposed rulemaking to establish a separate PEL for diesel particulate (MSHA, 1992)."

Nov 1, 1995

By F. W. Bradley

MY first Nevada City mining reminiscence is one of seeing Capt. Thomas Mein, over 52 years ago, in the old Wyoming mill on Deer Creek about a mile below the town of Nevada City. Captain Mein was then superintendent of the Wyoming mine, where the old fashioned Cornish pump was used, as well as hurdy-gurdy water wheels for power. This mill was one of the typical, up-to-date mills of that time and consisted of stamps, fed by Chinese hand feeders, who also cobbed the ore down to a small enough size to be fed into the mortars. Stamps at that time were of light weight and crushed about one ton to one and a half tons to the stamp, the pulp going over plates, then into sluices with self-raising gates. When a sluice became full the pulp was shut off and directed into the parallel sluice, also with a self-raising gate. The concentrate thus collected in the sluice was shoveled out and carried to Cornish buddles and there cleaned up, preparatory to being sent to a local custom chlorination works.

Jan 1, 1929

By E. D. Gardner

FIFTY years ago the Utah Copper enterprise at Bingham was just getting under way. An epic in metal mining was in the making. Throughout the West the bonanza deposits were approaching exhaustion and most ore still went direct to smelter. But concentrators were shortly to be constructed for treating milling grade ores, and most important, the pilot plant for the Utah Copper enterprise was being built that year at the mouth of Bingham Canyon. The same decade was to see development at the Inspiration mine in Arizona of the most important new mining method for 50 years to come—undercut block caving. Although the average grade of ore being mined has been declining for 50 years, and wage rates and prices of supplies have been greatly increased, the mining industry has continued to grow and to prosper. Technology has advanced to a point where minerals can be mined under the most severe conditions. The hardest rock can be drilled and broken and the heaviest ground handled. Large or small, an ore-body can be mined successfully, at any desired rate of production. It is possible to pump great volumes of water and to ventilate the most extensive workings; air conditioning has made practicable the mining of ore where the rock temperatures are beyond those that can be borne by man. Mining today in the U. S. is a huge earth-moving operation. In 1953 nearly 2 billion tons of material were mined for direct use or for processing. Stripping at open-cut mines totaled about 1.7 billion cu yd. Table I gives relative tonnages of the branches of the mineral industry in 1953. In addition to the solid materials moved, 350 million tons of petroleum and 340,000 tons of gas were produced in 1953. Fifteen million tons of salt and 5 million tons of liquid sulphur were pumped from wells. An appreciable amount of copper was recovered by leaching old mine workings and dumps. Total value of minerals produced in 1953 was $14.4 billion: oil and gas $7.6 billion, coal $2.6 billion, nonmetallics $2.4 billion, and metals $1.8 billion. Formidable problems face some branches of the industry today, especially pertaining to increased output tons per manshift. The time has come when these problems should be reappraised. With current wage rates, the industry no longer can afford to pay men to do manual labor. It should be recognized, also, that the miner is a skilled worker; efforts to promote the dignity of his calling and his pride of accomplishment have yielded beneficial results. Mineral deposits occur under widely varying conditions. In most instances the degree of support needed by the roof and walls is the deciding factor in selection of an underground mining method. The degree of support needed, in turn, is governed by natural physical characteristics of the ore and its enclosing rocks. Mine operators, of course, learn to judge ground by observation, and an experienced mine boss generally can anticipate what will happen following any given mining operation. A more scientific approach, however, would be advantageous in most cases. More should be known about the strength of the ore and the enclosing rocks, more about stresses set up in the ground when ore is removed, and more about the mechanics of moving ground. Better understanding would work both ways: first, favorable rock conditions could be fully utilized for more efficient mining, and second, hazards of rock falls could be minimized, loss of ore in mining reduced, and expenses caused by ground pressures and subsidence lowered. In general, mining comprises breaking the ore or rock in place, supporting the mine workings, and transporting the ore to the surface. This latter is a materials handling problem. Ventilation, of course, must be provided, and the mines must be kept free of water. Development work at some places is the most important cost item in extracting ore. Drilling and blasting remain the usual practice for breaking ore or rock from place except, of course, at block-caving mines. The drilling and blasting practice at a mine must fit the mining method. In laying out mining procedures attention is being given to

Jan 1, 1956

By Mine F. J, Woods P. H

The Top End of the Northern Territory lies in the monsoonal zone and receives rain during the November-April period. Initially, at the start of the wet season, rain storms are localised, but, following the descent of the monsoonal trough from below the equator, widespread rain occurs. Overflow incidents at mine sites tend to arise midway through the annual wet season when excess water accumulated in ponds begins to discharge to the external environment. Remote-access monitoring may be undertaken at mine sites using equipment to continuously measure water quality parameters with storage of the information on a data logger. The data is then retrieved by visiting the site and transferring it to a portable computer or by remotely accessing the system using a telemetry system and transmission via telephone, VHF/UHF or satellite. Such systems are readily available and vary in cost depending on the sophistication of the data transfer system. Available sensors for continuous monitoring include those for conductivity, temperature, pH and other ion selective electrodes, eg nitrate, and water level. Of these variables, conductivity is most useful due to its inherent accuracy and stability of reading. Remote monitoring capability is able to provide: (i) more intensive monitoring of key issues; (ii) more timely information; (iii) correct perspective on the degree of environmental problem; and (iv) information from remote locations, which would be difficult to monitor by more conventional methods. Examples are given for applications of continuously logged measurement of conductivity of waters discharging to drains and in creeks at Pine Creek, Ranger, Nabarlek and Woodcutters mines in the Northern Territory. These applications demonstrate the timeliness of the continuous monitoring technique.

Jan 1, 1994

By J. E. Chappelear

We are concerned with the problem of calculating the forces produced by passing waves on a submerged object (in particular a drilling barge) located on the ocean floor. We employ the linearized theory of waves (the Airy1 theory), since solutions are generally more easily obtained in such a theory. It will be indicated how an approximate solution to the problem can be obtained for waves of finite height by use of a linear combination of Airy waves. We shall assume the submerged object has an infinite length, thus neglecting diffraction and making the problem two-dimensional. We find that there is not a considerable difference between our solution and the usual engineering solution. The force, as a function of time, is plotted in Figs. 4 and 5, together with the usual solution for easy comparison. So far, no experiments have been found to compare with the results. As will be shown, the calculations can be extended to waves of finite height (Stokes2-Struik3 waves) in an approximate fashion. This can be done by calculating the force produced by each Fourier component of the wave, separately, and omitting the coupling between the various harmonics produced by Bernoulli's theorem. The problem and its boundary conditions will be briefly stated. We seek a function, +, the velocity potential, which is harmonic, ?2?=0...........(1) and which satisfies the boundary conditions ??/?n =0 .......(2) (the normal derivative of + is zero) on the ocean floor and the sides of the barge, and s??/?y = ?..........(3) on the ocean surface, where s = g/w2........(4) The physical reasons for these choices and an interpretation of ? are given by Lamb.' As previously stated, we assume also that the problem is two-dimensional. We set up our coordinates such that x = 0 is the center of the barge and y = 0 is the ocean floor. The coordinates are shown in Fig. 1, together with the location of the barge on the bottom. Our solution may be decomposed into a function which is symmetric about x = 0,?e, and one which is antisymmetric, +,, ? = ? + ?o...........(5) Thus directly above the barge we have as boundary conditions that for x = 0, ?o = 0, ...........(6) and ??e/?x = 0........(7) Now, far from the barge, we have that (for x positive and assuming the waves are incident from the left) ?e ? Ae cosh ky cos k (x + a) , . . . (8) and ?e ? Ao cosh ky cos k (x + ß) . . . . (9) where + means ". .. approaches ... for x large." Let us put Ae, Ao, and k equal to one, and remember that, in accordance with the derivation of Eq. 3, a sinusoidal time factor is to be supplied. Then we may rewrite Eq. 8 for ?e, and we find that

Jan 1, 1958

By Jr. Gambrell

For more cost effective strata control, a fundamental understanding of the behavior of the support system is needed. To assist in this understanding for shield supports, behavior of a four-leg shield design used on a soft floor in an operating longwall system is presented. The shield was constructed having a split base and a split caving shield. Attention is focused on other-than-normal loading on the canopy and its effect on deformation of the lemniscate links. Examples of the typical bending and twisting deformations are given. Schematics of the canopy, caving shield, and lemniscates showing important forces and moments are presented. Approximate minimum values of the forces and moments are calculated. The need for use of more inclusive three-dimensional design techniques is demonstrated.

Jan 1, 1990

By Dix, E. H.

THE percentage of manganese used in commercial aluminum alloys is small, and yet this element is an important addition to some very valuable alloys. When used alone with commercial aluminum containing iron and silicon as impurities, the usual percentage in wrought materials is from 1 to 1.5 per cent., whereas castings may contain as much as 2 per cent. An aluminum-manganese alloy containing nominally 1.25 per cent. manganese is much used in sheet form for the manufacture of cooking utensils and other articles requiring a little greater strength and hardness than could be obtained with commercially pure aluminum. It is also used for various purposes in the form of rods, tubes and pipes. The aluminum-manganese alloys, both wrought 'and cast, offer excellent resistance to many kinds of corrosion attack. The U. S. Naval Gun Factory uses an aluminum alloy containing from 1 to 2 per cent. each of copper and manganese, for both castings and forgings. Manganese is also used, up to about 1 per cent., as a minor alloying .element in several of the strong aluminum alloys of the duralumin type. It is felt that the role of this element when thus used has not been fully understood, but it is believed that the results obtained in this investigation will throw additional light on the subject. The earlier work on the system aluminum-manganese was general in nature, and no detailed investigations of the relations existent in the useful aluminum-rich alloys have been reported. Guilletl1in 1902 surveyed the system, and Hendrichs2 in 1908 published an equilibrium diagram which, although based on .few data, is often used in the literature. Fragmentary work has also been done by other investigators."

Jan 1, 1927

By Gary A. Nowlan

The Casa Grande West-Santa Cruz porphyry-¬copper deposit is in the Basin and Range physiographic province west of Casa Grande, Arizona (Fig. 1). The Casa Grande West portion of the deposit is controlled by Casa Grande Copper Company and the Santa Cruz portion by ASARCO. The deposit contains at least 350,000,000 metric tons of rock with greater than 1 percent Cu. The deposit is covered by at least 300 m of sediment, with no visible expression of the deposit at the land surface. The deposit is in an area of prime agricultural land that depends heavily upon well irrigation because of a hot and arid climate. Because of the deep sedimentary cover, the chance is extremely remote that the geochemistry of soil or stream sediment would reflect the deposit even if the land surface were not disturbed by many years of farming. Irrigation wells of the area generally bottom in the sedimentary cover. The purpose of the study is to see if the Casa Grande West-Santa Cruz deposit is geochemically reflected in ground waters over and near the deposit.

Jan 1, 1981

By Ernesto Kausel

El presente texto describe la acción de microorganismos en el proceso de oxidación de diversos minerales. Los microorganismos en cuestión son el Thiobacillus Ferroxidons y el Thiobacillus Thioxidans. Asimismo, las aplicaciones de estas bacterias en el futuro se puede desarrollar a través de la fabricación de H2S04 a partir del azufre elemental, la lixiviación de minerales sulfurados y la regeneración de soluciones de sulfato ferroso.

Jan 1, 1961