Search Documents

By D. van Heerden

In the mining industry abrasion caused by both sliding and impact have over the years resulted in costly damage to installations such as ore passes and silos. Good geotechnical practices combined with the use of a high quality abrasion resistant concrete can prolong the life of such an installation and minimize problems associated with abrasion. In order to maximize the life of an abrasion resistant concrete, the choice and combination of the correct raw materials (cement, aggregate and fibre) and overall mix design needed to make up such a concrete are important. This paper presents technical data and practical experience showing that concrete formulated with calcium aluminate cement resists severe abrasion conditions better than similar OPC-based concretes.

Jan 1, 2005

By Ghassan Skybey

Australian coal mines uses state of the art technology in coal rib reinforcement. This paper highlights the development over the past 15 years in coal rib support technology, along with the advantages and disadvantages of each system. It also outlines the current trend in using coal rib reinforcement in speeding up the dowels installation to improve the current low drivage rate. An innovative cuttable dowel is discussed which improves the drivage rate. This new dowel is self anchoring it uses no resin anchor it has a 5 tonnes (5.51 tons) anchor capacity and can be fully installed in approximately 10 seconds.

Jan 1, 1995

By H. R. Pierce

A gas well has a certain definite capacity to deliver gas from the gas sand through the producing string of pipe. This capacity depends upon the pressures in the sand; that is, a well will deliver gas at a rate of flow which is determined by the formation or "shut-inn pressure in the sand and the back pressure at the face of the sand in the well. The three factors, rate of flow, formation or "shut-in" pressure, and the back pressure, for a given well, can be written into a fundamental relation which is strictly applicable only to that well. This relation can be used to determine the capacity of the well to deliver gas from any formation pressure against any back pressure held at the f ace of the sand in the well. Studies have been made of the deliveries of 400 gas wells operating under different conditions of pressure, Most of the wells which have been studied are in Osage County, Okla.; however, several representative studies have been made on wells in southern Louisiana, southern Texas, the Texas Panhandle, and West Virginia.

Jan 1, 1929

By Michel C. Frippel

This section of the Minerals Yearbook reviews the minerals industries of 29 countries: the 12 nations of the European Community (Belgium, France, the Federal Republic of Germany (FRG), Italy, Greece, the Netherlands, Denmark/Greenland, Spain, Portugal, Luxembourg, The United Kingdom, and Ireland); 6 of the 7 nations of the European Free Trade Association (Sweden, Norway, Finland, Iceland, Austria, and Switzerland); Malta; the 8 Centrally Planned Economies of Eastern Europe (the German Democratic Republic (GDR), Poland, Yugoslavia, Albania, Hungary, Czechoslovakia, Romania, and Bulgaria); and the U.S.S.R. Western Europe Western Europe [loosely defined to include the 12 nations of the European Com-munity (EC) and the 7 nations of the European Free Trade Association (EFTA)] is the single largest trading area and consumer of raw materials in the world. If Western Europe was at one time an important mining sector, it has now increasingly relegated the role of supplying minerals for its minerals processing industry to its ex-colonies in North and South America, Africa, and Australia. In this regard, Western Europe is the most important determinant of raw materials consumption (and thus, indirectly, raw materials production). There is an important reason for this since Western Europe lies somewhere between Japan at one extreme and the United States and the U.S.S.R. at the other extreme as regards the availability of natural resources.

Jan 1, 1992

It is the purpose of this paper to produce some evidence on the accuracy to be expected from normal assay procedure using the usual first class equipment, and to examine the effect that many assaying inaccuracies have on reported metallurgical recoveries.Generally speaking, the evaluation of the gold content of a mineral ore sample by the fire assay method is a relatively simple process.A weighed quantity of finely ground ore is fused with suitable fiuxes including litharge and a reducing agent to give a button of lead and a quantity of slag. The shower of lead produced by the reduction of the added litharge collects the gold and silver present in the ore, concentrating the values into the lead button.The button of lead, after separation from the slag, is, on heating in an absorbent cupel in a current of air, reoxidised to litharge and absorbed into the cupel leaving a gold and silver bead in the cupel. This bead' is heated in a solution of nitric acid to dissolve the silver, leaving the gold undissolved to be dried and weighed. Knowing the original weight of the ore and the weight of the gold prill the value of the ore is easily calculated.Summarising1. Fusion Process.-Ore plus fiuxes give a slag plus lead button.2. Cupellation Process.-Lead button is re-oxidised to litharge leaving a gold and silver bead.

Jan 1, 1952

By L. F. Ruppert, P. A. Freeman, R. C. Milici, S. J. Tewalt, L. J. Bragg

The U.S. Geological Survey has completed a dig-ital coal resource assessment of six of the top-producing coal beds and coal zones in the northern and central Appalachian Basin coal regions. These include the Pennsylvanian-aged Pittsburgh, Upper Freeport, Lower Kittanning, Fire Clay, Pond Creek, and Pocahontas No. 3 coal beds and coal zones. Resources were calculated on all of the coalbeds/zones, with the exception of the Lower Kittanning coal bed. Preliminary original resources are estimated at about 93 billion short tons (84 billion tonnes), of which about 66 billion short tons (60billion tonnes) remain. Much of the remaining coal in all five coal beds/zones is thinner [<3.5 ft (1.07m)] and deeper [>1,000 ft (305 m)] than the coal that has been mined, but economic resources are still available and mining in each coal bed/zones will continue throughout this decade and into the next given current market conditions.

Jan 1, 2001

By Anat Deepatana

Bioleaching of nickel laterite ores is the extraction technology based on the use of heterotrophic micro-organisms and their organic acid products to dissolve metals from oxide minerals. This study examined the chemical leaching kinetics of limonite and nontronite ores with metabolites including citric, lactic and malic acids. The leaching process was found to follow the chemically controlled model. The leaching kinetics was found to be significantly influenced by the acid strength or dissociation of acids in solution. Although increasing the acid strength increased the rates of leaching, this trend was not indefinite. An optimal acid concentration that defined the fastest leaching rates was identified for each acid. The amenabilities of the minerals hosting the nickel and cobalt in limonite and nontronite to organic acid leaching were also established.

Jan 1, 2006

By T. M. Bhatti

The main purpose of present study was to characterize the dissolution of uranium from low-grade black shale with indigenous isolated strain of Acidithiobacillus ferrooxidans (BSAF-01). The nature of shale is quartzite-schistose and contains uranium content of 0.005% U3O8 (50 ppm U3O8). Uranium is present in the tetravalent oxidation state (U4+) in the shale matrix. The main minerals identified are graphite, quartz, pyrite, mica minerals (phlogopite, biotite, sericite, and chlorite), microcline, K-feldspar and kerogen (hydrocarbon-compounds). Bacterial oxidation of pyrite was an acid-generating system and produced sulfuric acid and ferric sulfate during this biological phenomenon. A series of bioleaching experiments were conducted in shake flasks for leaching of uranium from black shale. The leaching experiments were performed at 50% pulp density using indigenous Fe- and S-oxidizing bacterium (Acidithiobacillus ferrooxidans). Bioleaching data revealed that about 90% ~ 95% U3O8 was leached out from black shale ore. Uranium dissolution from shale depends on pH (pH 1.5~1.9), redox potential (=500 mev) and the concentration of Fe2+ and Fe3+ ions in the leaching environment. The oxidative leaching of U4+ involves a redox reaction with Fe3+ as an oxidant and bacterial re-oxidation of Fe2+ in acidic leaching environment. Uranium leaching efficiency was attributed to the sulfuric acid and ferric sulfate production during bacterial oxidation of pyrite.

Jan 1, 2014

By Emery Chilton, Charles Taylor, Mark Senk, Linda McWilliams

Three-axis ultrasonic anemometers are used to study airflow in the NIOSH ventilation gallery where ventilation in an underground mine is simulated. In this study, performance characteristics of this anemometer are evaluated and the effects of sensor orientation and sampler location on flow readings are examined. The study results provide guidelines for more effective use of the ultrasonic anemometers in the ventilation gallery.

By T. F. Witherbee

THE Fletcherville Furnace was built in 1864 and 1865, making its first blast from August until October of the latter year, when it was blown out to prevent its "bunging-up." Repairs were made in time to enable it to be blown in again December 12th, 1865, the blast ending October 7th, 1866. Total product 1921.15 tons iron, an average of 6.8.2.5 tons per day, from ores yielding 44.8 per cent. Consumption of charcoal 223.2 bushels per ton of iron. The furnace journal up to this time shows no record of furnace dimen¬sions, or temperature of the blast, but as near as can be ascertained, they were as follows, viz. Height of stack, 42 feet. Diameter of bosh, 11 feet. Angle of bosh, 7 1/2 inches to 12 inches rise, about 58°. Diameter of open tunnel head, 42 inches. Number of tuyeres 3; each 3 inches in diameter. Dam 15 inches high. Tuyeres 24 inches high. Tymp 22 1/2 inches high. Diameter of steam cylinder, 20 1/4 inches. Stroke 5 feet. Diameter of blast cylinder, 64 inches. The engine is direct-acting horizontal non-condensing. December 26th, 1.866, the furnace was again put in blast, having been considerably altered in the crucible; the height of stack, bosh, and tunnel head remaining as before. Six tuyeres were put in, three in each of the side arches. The hearth or crucible was rectangular in form, 3 feet wide x 32 feet long x 62 feet high. Inclination of bosh 58°. Height of tuyeres 26 inches ; nozzles 2 1/4 inches diameter. Temperature of blast estimated to be about 500°.

Jan 1, 1874

By Z. Zhang, D. Bouchard, H. Blanchette, A. Lemieux

This paper describes quality control methodologies for the production of semisolid A356 aluminum slugs with the SEED process. A methodology based on destructive tests carried out with an apparatus measuring the force to slice the slugs is presented. The force measurements were correlated with the solid phase morphologies of the slugs and were validated against a non destructive methodology that consisted in monitoring the temperature evolution of crucibles to produce the slugs and the drained metal. Results from the destructive and non destructive methodologies are compared and discussed.

Jan 1, 2006

By Deborah A. Kopsick

Several minerals were observed and collected in a small gully originating from a weathered coal processing waste (gob) pile in Barton County, Missouri. The rapid alteration of these various minerals after collection suggested that they might represent a dehydration sequence. X-ray diffraction of the dehydrated and rehydrated minerals deposited on the gob pile indicated the presence of the monohydrate and heptahydrate forms of ferrous sulfate, szomolnokite and melanterite respectively. The occurrence of melanterite (FeSO4.7H2O), was limited to isolated areas of ponded water while szomolnokite (FeSO4.H2O), was associated with the outwash areas of the pile. Laboratory dehydration of melanterite collected at the gob pile revealed the formation of rozenite (FeSO4.4H2O), an intermediate form of ferrous sulfate. Szomolnokite was shown to be the stable form of these ferrous sulfates during these experiments while melanterite and rozenite were shown to alter readily. Chemical analysis of szomolnokite revealed enrichment in Fe, Mg, Zn, Cd, Cu and Mn relative to the chemical composition of the gob ad the lechate generated from the gob wastes. Although this gob pile had been weathering for more than 35 years, significant concentrations of trace metals were still being released from the pile through the generation of leachate and the formation of various soluble metal enriched ferrous sulfate minerals.

Jan 1, 1982

By Dipak C. Talapatra

This report describes the development of guidelines for design, inspection and maintenance of automatic couplers. In order to devise the guidelines, performance requirements for automatic couplers were carefully established. This was clone through a comprehensive survey of coupler manufacturers and extensive observation of automatic couplers in service in a broad spectrum of mines. The capability of the couplers to withstand the demands of the mining environment in terms of strength characteristics, gathering range, curve negotiability, and other factors were all carefully evaluated. An analysis of coupler related accidents for the years 1972-1976 was carried out to provide information on the safety and reliability of existing automatic couplers. This formed an important input to the development of the guidelines. It is expected that these guidelines will he useful to coupler manufacturers for establishing designs for improved automatic couplers, and to mine operators for maintaining their couplers in a safe and good operating condition throughout their expected lifetimes. This report is in two volumes: Volume l - Technical Report Volume 2 - Design, Inspection, and Maintenance Manual

Jan 1, 1977

By J. Bilant, B. Carlson, N. Gow

"High-pressure grinding roll (HPGR) technology was evaluated to replace tertiary cone crushing at Coeur Rochester operations (Coeur Rochester Inc.) as an opportunity to improve silver recovery. In 2016 and 2017, onsite and third-party pilot programs were initiated to evaluate the impact on metallurgical recovery and heap leach performance of crushed product generated by an HPGR. In 2018, Forte Dynamics evaluated the HPGR laboratory metallurgical data from Coeur Rochester and all third parties to develop field-scale leach curves based on new crushing scenarios. The laboratory recovery test work data were consolidated and scaled to field conditions to determine projected heap leach performance. Based on the metallurgical testing conducted, the replacement of current tertiary cone crushers with HPGR technology has the potential to increase Coeur Rochester’s silver recovery rate by 8 percentage points, from 61 percent to 69 percent, and shorten the overall timing of silver recoveries from 20 years to just more than two years.The Rochester Mine, and associated valley fill heap leach facilities is an openpit silver and gold mine located in Pershing County, NV, approximately 42 km (26 miles) northeast of the city of Lovelock. In 2017, Rochester produced approximately 4.7 million oz silver (Ag) and 51,000 troy oz gold (Au). Ore mined at Rochester is either fed directly to the primary X-Pit crusher, crushed at an in-pit crusher system, or placed directly onto a heap leach pad as run-of-mine (ROM). Both crushing circuits are comprised of three stages of crushing to produce a nominal 3/8 in. ore. Primary crushing consists of jaw crushing while secondary and tertiary crushing are composed of varying cone crushers.Historical recovery rates of crushed Rochester ore averaged 61.4 percent Ag and 95.9 percent Au over a period of 20 years (Robinson et al., 2018). These rates were derived from third-party verification of in-house metallurgical test results, crusher production and heap leach production results from 1986 through 2004 in a private report for Rochester produced by KD Engineering Co., Inc. Recovery rates are regularly verified by compositing daily samples of ore delivered to each leach pad from the X-pit crusher, in-pit crusher and/ or ROM. A proportionate split of each sample is used to generate monthly composites for metallurgical analysis utilizing column leaching and bottle roll leaching. These tests are run in a manner analogous with production conditions and deliver test results that provide expected heap leach performance. As the Rochester oxide deposit has been mineralogically and metallurgically consistent, the gold and silver recovery trends have also been consistent over the life of the project."

Sep 1, 2019

By Karl J. C. Harries

"4.1. INTRODUCTIONThis chapter, although divided into four parts, deals with only two principal topics. The first briefly describes and discusses some common types of property interests and considerations relating to them and the second deals with entering upon privately owned lands and obtaining the consent to do so.It should be noted that the terms “mining rights” and “mineral rights” are used interchangeably. As so used, they include the right to exploit the minerals and dispose of them for the benefit of the owner/lessee. This is relatively common in common law jurisdictions. In some jurisdictions, the two terms have distinct meanings, with “mining rights” referring to the right to work or exploit the minerals and “mineral rights” referring to the minerals themselves.Finally, it must be mentioned that the comments in the Introduction and §§ 4.2., 4.3. and 4.4. are based primarily upon Ontario law and Ontario’s mining and real property systems of registration. They have been included for illustrative purposes.4.2. LICENCES, CLAIMS, AND LEASESIn most jurisdictions, there are several basic types of interests that can be obtained from the state for mining purposes and that are of interest to the explorationist, as opposed to the operator. Different jurisdictions will have variations of these and possibly some extra ones that will address special purposes or local concerns. In virtually every jurisdiction, privately owned property rights are obtained through negotiation between owner and acquiror.Exploration or prospecting licence. This licence grants to the holder the right to prospect over a large tract of land and the exclusive right to acquire mining claims within that tract for the term of the licence. Such licences are usually negotiated documents requiring a minimum expenditure during the first year (often secured by a deposit or surety bond) and minimum annual expenditures thereafter to continue the licence in force up to its full term. The term will rarely exceed four years. The number of claims permitted to be staked will be limited in some way, possibly as to a maximum aggregate area or a maximum number of claims per annum. It is normal for the holder to have to drop part of the licensed area each year, so that the area shrinks annually, although exploration expenditure requirements will usually increase.These types of licences are usually used by governments to encourage exploration of otherwise unattractive or remote areas, such as the far northern parts of some of Canada’s provinces. They do not grant any real property interest in the area for which they are issued, and they will be subject to any claims or property rights that exist in the area. They are contracts with the state that grant certain exclusive rights in return for commitments to carry out work. They may or may not be specifically authorized by statute."

Jan 1, 2003

By Christa Overby

As part of the City of Portland, Oregon?s East Side Combined Sewer Overflow Tunnel Project, nine separate 2,130 mm (84-inch) diameter reinforced concrete pipe microtunnel drives totaling approximately 2,380 m (7,808 ft) are being constructed to divert flows from several of the existing outfalls to the main tunnel. The drives were constructed in challenging ground conditions that include soft soils under the ground-water table, large amounts of wood and metal debris, and close proximity to sensitive structures. While all of the drives will be addressed, the focus of the paper will be on the 931 m (3,055 ft) continuous drive connecting Outfall 46, currently the longest microtunnel driven in North America.

At its Copper Cliff Smelter, Inco Limited processes a bulk copper-nickel concentrate in two Inco oxygen flash furnaces. The furnace matte is converted to low iron matte for further processing, and the molten converter slag is recycled to the flash furnaces. The flash furnace slag is discarded. Natural gas or coke supplies a minor proportion of the process heat requirements, thus limiting the flash furnace matte grade to the target 45% CuNiCo. Coke addition to the furnace offers a potential means of establishing a reducing barrier on the surface of the molten bath. Such a practice would be conducive to producing sulfur deficient (partially metallized) matte. At the same iron content, the iron activity of sulfur deficient matte is higher than that of regular matte. A supernatant coke barrier could, therefore, be expected to lead to higher nickel and cobalt recoveries, reduction or even elimination of magnetite furnace bottom build-up and increased sulfur elimination as SO2 in the flash furnace. Preliminary experiments were conducted in a mini plant flash furnace to investigate the effect on process metallurgy of the suggested modified scheme. This paper presents the experimental results and discusses key aspects of the possible operation of the Inco flash furnace with a coke barrier separating the freeboard from the molten bath.

Jan 1, 2003

This paper describes major technical developments in rod mill design and operating practice since its introduction into the North American minerals industry over fifty years ago. The basic operating characteristics of the wet, overflow rod mill are described, and significant operating variables are reviewed in terms of their effects on mill power draw, power efficiency, and practical aspects of circuit operation. Key factors for improving the economic performance of rod milling circuits are identified.

Jan 1, 1986

By John Watson, Tom Treleaven

This guide presents nur-nerous patterns that provide 8 millisecond separations between initiated charges. The guide is tabulated in seven sections to provide Quick reference by number of decks or bunch blasting. The pattern IS presented in the section where the highe!$ number of decks works. It should be noted that patterns applicable to multipledackshwtings are alsoapplicsblefor fewer decks.

Jan 1, 1995

By P Christen

The Ernest Henry Copper gold mine situated in North West Queensland, Australia, is owned and operated by Xstrata Copper. Currently the open pit produces 11 Mtpa of ore. With open pit mining ceasing in mid 2011 development has begun on an underground sublevel cave mine to extend the life of the operation by another 12 years. When completed the open pit will be 530 m deep and 1.5 km in diameter. The orebody dips at approximately 45° and has been outlined a further 450 m below the base of the pit. This provides some challenges for the Ernest Henry underground mine which is designed to initially truck development and production ore from the end of the pit until a hoisting shaft is commissioned in 2013. Production will then increase to 5.0 Mtpa on its way to an ultimate rate of 6.0 Mtpa in 2016.This paper will focus on the capital development and infrastructure requirements for the underground mine. Areas covered include mine accesses, ore handling system, accommodations for the dip of the orebody, primary ventilation design, dewatering systems and selection of an underground workshop over surface only maintenance.Discussions include the complications arising due to the mine being located directly below a large open pit and the combination of first principle cost analysis and risk assessment which has been used to safely optimise the feasibility study designs.

Mar 21, 2011