Search Documents

By A. R. Mumford

During the course of an investigation conducted by the fuel section of the Bureau of Mines , on a hand- fired return- tubular boiler plant , it was found that the average cost of fuel to produce 1,000 lb. of steam was $ 0.5287 . Tests conducted after some simple changes had been made in the furnaces , and in the control of the boilers , showed the previous high cost of fuel per 1,000 lb. of steam could be reduced to the reasonable figure of $0.3540 , or the equivalent of over 30 per cent saving in fuel cost .

Mar 1, 1923

By R. A. Wyman, F. E. Hanes

THE demand for high-quality aggregate is increasing in all phases of the construction industry and in all organizations associated with road building in Canada. The production of aggregate in Canada has increased almost continuously since the end of the war and has quadrupled since 1948. Increases during the past fifteen years can be accounted for by the expansion in all types of construction, particularly that of roads and highways. Total construction in 1959, based on preliminary estimates, has been valued at $7 billion, and an increase fore-cast for 1960 indicates optimism on the •construction horizon (1). Cement produced in Canada in 1959 amounted to 6.3 million tons. This is more than 2.5 times the 1948 production. Increased cement production indicates an increased use of concrete, and thus an increased need for aggregate. Natural sand and gravel deposits are gradually being depleted.

Jan 1, 1962

By A. H. Bell

Continued low prices and restricted markets for crude oil discouraged drilling activity in Illinois oil fields during 1933. Only 36 wells were completed in the state, the smallest number since 1904, and of these the majority were scattered wildcat wells, only 10 having been drilled in producing fields (Table 2). Production was curtailed approximately 40 per cent for the first half of the year. During July, August, and the early part of September there was no restriction on production. On Sept. 8, under the "code of fair competition for the petroleum industry," the quota of allowable production for Illinois was fixed at 12,000 bbl. per day. The state's production in 1933 was 9 per cent less than in 1932. What it would have been had there been no curtailment of production and if economic conditions had permitted a normal amount of cleaning out and repairs to wells, it is not possible to estimate, but it would no doubt have been considerably more than the actual figure. No new pools or new producing horizons were discovered in 1933, but the deepening of a Robinson sand well in Crawford County to the McClosky "sand" horizon (St. Genevieve limestone of the Lower Mississippian) resulted in a production of 3 bbl. per day (Fred Patchel, Savilla Shipman No. 5, NE. 1/4, SW. 1/4, sec. 26, T.6N., R.l3W., deepened from 1122 to 1388 ft., to be tested to the McClosky horizon, and, owing to the rapid variations in porosity within short distances, as shown in the Lawrence County field to the south, one test may not be considered as proving or condemning any large area. The average price of Illinois crude oil in 1933, calculated from the posted prices as published in the Oil and Gas Journal and Oil Weekly, was $0.862 per barrel. This compares with a calculated average price of $1.032 in 1932 and 0.852 in 1931. The total value of Illinois crude oil produced in 1933 obtained by multiplying the average price (0.862) by the total production (4,227,000 bbl.) was $3,643,674. Of the 26 wildcat wells drilled in 1933, only one was drilled on known favorable structure. This was the Walmar Oil Company's William Pepple well No. 1, sec. 12, T.4N., R.12W., Hancock County, which tested

Jan 1, 1934

By Thomas W. Chapman, Shi-Chern Yen, I-Min Lu

"An electric field was applied to a metal-bearing kaolinite specimen to investigate the efficiency of electro-osmosis in removing heavy metals from contaminated soils. The electric field induces a flow of water through the porous medium, called electro-osmosis, which is superimposed on the hydraulic flow. Because the electro-osmotic flow is relatively stronger in smaller pores, it can enhance the displacement of contaminated solution by fluid convection. Furthermore, local changes in pH caused by the electrode reactions can affect adsorption equilibria and the distribution of solutes between the solution and the solid surfaces.The electro-osmosis experiments were conducted by applying either a constant current or a constant voltage across 8-cm inside diameter, 25 to 30-cm long specimens of kaolinite clay with graphite electrodes. Samples of the pore fluid and of the clay were analyzed to determine metal content, pH, and conductivity as functions of time and position. Results show that removal of heavy metals from soil can be accomplished effectively by electrokinetic treatment of sufficient duration. Approximately 95% of the lead was removed after 189 days.IntroductionRemediation of soils contaminated with toxic chemicals is a difficult and expensive task. Washing or leaching are not particularly effective if the contaminate is sequestered in small pores; hydraulic flows of water pass through larger pores leaving the smaller pores relatively untouched. Electro-osmosis appears to be the most promising new technology for removing heavy metals and organic substances from contaminated soils (Segal, 1980; Hamed et al., 1991, Masliyah, 1994).Electro-osmosis is one of several electrokinetic phenomena that occur through the interactions among an electric field, fluid motion, solute adsorption, and the existence of a net charge on a solid-fluid interface (Newman, 1991, Masliyah, 1994). Electro-osmosis refers to the fluid flow in a porous medium that results when an electric field acts on the mobile region of the electrical double layer, the solution-side region of charge separation that exists at the pore walls."

Jan 1, 1996

By L. W. Kelly

The purpose of this paper is to describe several methods that have been employed in successfully recovering roof bolts in Indiana, Illinois, and western Kentucky coal mines, the States where successful roof-bolt recovery was started. As far as is known, the first bolts were recovered in a mine in western Kentucky in January or February 1951. In April 1951 a meeting was held at that mine to discuss the recovery of roof bolts. The meeting was attended by A. D. Sisk, former Chief, Kentucky Department of Mines and Minerals; and L. W. Kelly, Federal Bureau of Mines; and officials of the coal company. Inasmuch as roof bolting was in its infancy, the thinking regarding roof bolts at that time was on the problem of getting them in, not getting them out; consequently, the thought of recovering them was revolutionary. The subject was discussed at length from all angles, and it was finally agreed that, if certain safeguards were taken, no agency represented at the meeting would oppose the practice. That this decision was sound has been proved, as thou-sands of bolts have been recovered in the Middle West without a lost-time accident. Recovering roof bolts is a simple operation; consequently, no complicated equipment had to be designed or built for this purpose. However, about 5 years ago, officials of the Traux-Traer Coal Co. conceived the idea and constructed a mechanical device for recovering bolts that has been very successful and has been copied widely in this area. This device will be discussed in detail in part II of this paper.

Jan 1, 1958

By S. Nikolic

"Calcium ferrite slags are currently used in a number of copper-converting processes. Despite the industrial importance of this system the phase equilibria have not been fully investigated. Characterization of this slag system is necessary to improve the control of process parameters, including fluxing and operating temperatures. Recently, a modified experimental method has been developed; this involves rapid quenching of slag samples equilibrated at high temperatures with the resulting phase assemblages analysed using electron probe microanalysis (EPMA). In the present study, experiments were completed under controlled temperatures and oxygen partial pressures using CO/C02 or H2/C02 gas mixtures. The investigated slags were supported during equilibration by a substrate of the primary phase. This technique removes the limitations arising from the use of crucibles and facilitates rapid quenching of the melt. Experiments were carried out at 1200°C and 1250°C (1473 Kand 1523 K) and in the composition range 0-40 wt.% Cu20, 0-25 wt. % CaO and 45-80 wt. % Fe203. Liquidus and solidus data are reported for the primary phase field of spinel between the oxygen partial pressures of 10-4.5 to 1 o- 6-5 atm. The analyzed compositions of liquids and solids are used to construct the phase diagram of ""Cu20"" -CaO-""F ez03"" system in equilibrium with metallic copper at fixed oxygen partial pressures."

Jan 1, 2007

By H. W. Brandt

A field test was designed to inject a specially formulated two compound epoxy resin into the roof rock ahead of a working face to cement fractures and formation interfaces at the Westmoreland Coal Co., Winding Gulf Div., Eccles No. 5 Mine, Eccles, West Virginia. Five 30 foot long X 2 inch diameter, hold were drilled at an angle of 15° above the plane of roof line front the face of a working entry. The epoxy resin compounds were pumped through a proportioning unit and mixed in-line before being discharged into the drill hole under treatment it injection pressures up to a maximum of 450 psig. When the coal face was advanced an anomalous failure of the roof rock occurred in the treated section. Further testing was suspended until the cause of the failure could he determined. The polymers were tested, under confined conditions, in 2 inch pipe columns. Extreme temperature and pressure (up to 2400 psig) rises were recorded as they cured, It was concluded that this pressure source fractured the rock and caused the roof failure. The entire program was terminated after it was determined that the heat rise and resultant high pressures could not he controlled chemically or mechanically.

Jan 1, 1978

By C K. Boafo, J Visser

Obuasi Mine in Ghana, with more than 100 years of mining history, developed from a surface operation into a deep >2000 m underground gold mine. The challenge is to extract value from narrow veins left after extensive mining in the wider ore zones of the mine. Since the merger of AngloGold and Ashanti Goldfields in 2004 the mine strives to achieve optimum extraction through an integrated Mineral Resource management process from geological modelling, resource evaluation to mine design and scheduling. The shear hosted gold deposit displays complex secondary shears of variable thickness and continuity. There is an ongoing process of changes taking place in the way that geological modelling and resource estimation is done. Recent developments include the use of computerised systems that support the whole resource management chain from resource modelling to reserve optimisation. The change in thought and technology now allows for targeting narrow veins previously ignored in optimisation and mine design since moving into mechanised mining. The increased knowledge and confidence in the resource models now allows for flexibility in mine design, selection of mining method and scheduling and extraction of the reserves. The focus area for change is the way the orebody is evaluated and extraction designed. Since 2005 major changes were made to the process. This paper considers the historical approach of resource management. It looks at the individual process changes and qualifying the way ahead.

Jan 1, 2008

By Raju S. Sagi

This paper deals primarily with the different types of drilling methods used by the Iron. Ore Company of Canada for sampling the soft and friable hematite-limonite (secondary) iron ore deposits found in the Scheferville area. The problems associated with drilling, sampling, sample handling and sample preparation. for chemical analysis of these ores are discussed. Systematic evaluation of the various drilling methods led to the selection of an integrated drilling system. This system consists of a rotary dual- tube - reverse-circulation drill, with tricone bit, polymer mud and mechanical sample splitter, The historic al development of this drilling system is described in detail, as are the equipment , sample flow and quality control checks carried out to obtain representative samples. This integrated drilling and sampling system has been used satisfactorily on a routine basis for determining the grade and tonnage of ore for the various deposits for the last five years (1972-76) in the Schefferville area.

Jan 1, 1977

By Lawrence K. Requa

The property being worked by the Lewiston dredge of Placer Development (Ltd.) is on the Trinity River in Trinity County, Calif., about 9 miles north of the town of Lewiston (see fig. 1). The nearest rail point is at Rending, Calif., which is exactly 50 miles bar road from the dredge camp. Recently a very good section of State highway has been constructed from Redding to Weaverville, and it is now possible to use this highway for 35 miles of the distance between the dredging property and Redding. The remaining 15 miles, however, are over ordinary dirt road. No trouble is experienced in reaching the property except for a few weeks during the middle of the winter when snowstorms may make travel difficult but not impossible. At present the property consists of about 500 acres of patented land, which extends for about 3 miles along the main Trinity River and Stuart's Pork. It is being worked with one 7-cubic foot, Bucyrus-type dredge, which has an average monthly capacity of about 100,000 cubic yards. To the end of 1931 approximately 10,000,000 cubic yards of gravel had been dredged.

Jan 1, 1932

By Harry R. Nicholls

The objectives of this investigation were to determine the strain propagation laws for a strain pulse in salt and to compare the seismic effects from the detonation of different explosives in salt. The investigation showed that a strain propagation law of the type, e = K(R/W 1/3 ) n, and a strain energy propagation law of the type, Ea/W 1/3 = K(R/WI/3)b , are valid in salt. A change in the regression law coefficient, n , was noted with strain level. A similar change in b was inferred because strain energy is proportional to the square of strain amplitude. Particle velocity data may be used interchangeably with strain data under the test conditions.

Jan 1, 1962

By Dalia. R. Mohamed, Hisham H. Hafez, Marawan M. Shahien

"Construction activities in major projects that involve deep excavations necessitate the use of vertical walls surrounding the construction site to play an important role as earth retention system. The walls are usually partially penetrating impervious walls which can increase the efficiency of the ground water control system that usually consists of number of partially penetrating wells. The analysis and design of such system requires 3D numerical simulation. The aim of this study is to develop simplified semi-empirical approach to analyze and design such system. The analyzed model is a single well in a square site that is surrounded by impervious walls along the perimeter of the site in an unconfined aquifer. The results of the parametric analysis are presented in this paper aiming to assess and understand the factors that influence dewatering in terms of ground water or drawdown profile surrounding the well. The parametric analysis is carried out using the 3D finite difference software. The parametric analysis comprises with more than 550 cases calculated. The study involved the parameters; well penetration depth, impervious wall penetration depth, size of the construction pit, coefficient of permeability, well yield and well location or distance between well center to impervious wall edge.IntroductionThe presence of groundwater in a site may have impact on the construction processes involved during the course of project construction, especially those projects that involve deep excavations. Deep excavations, especially in urban areas, require the construction of supported walls all around the site perimeter to ensure the stability of the excavation. In most of cases, the constructed walls are relatively impervious. Depending on the ground and site conditions, the walls are not penetrating all the way down through to the bottom of the aquifer and thus the walls are partially penetrating walls. The presence of ground water necessitates the lowering of the groundwater to levels below the bottom of the excavation to ensure working in dry. This paper focuses on groundwater control systems that consist of deep wells inside square areas enclosed by impervious walls partially penetrating unconfined aquifers. The wells are partially penetrating the aquifer, as well. There are many factors or parameters that are related to the configurations of the components of the system that may influence the drawdown of a well in such groundwater control system. This paper is a part of a comprehensive study that aims to development of a simple method for estimating the drawdown of dewatering system of the described configuration. In order to achieve such a major goal, a 3D finite difference model is developed for the problem in hand. A comprehensive parametric analysis was then carried out to investigate the influence of all the parameters on the drawdown of a deep well in such groundwater control system. This paper describes the problem, the model, the parametric analysis including the involved parameters. The paper, then, demonstrate the results of the analysis showing the influence of the studied parameters on the drawdown of a single well."

Jan 1, 2016

By Darren Thorton, David Sprott, Ian Brunton

Blasting causes movement of the rock and can be detrimental to the accurate delineation of the ore and waste regions within the resulting muck pile. The consequences can be ore loss and dilution. However, ore loss and dilution can be minimized and significant increases in profit can be realized if the movement can be accurately measured. Various methods have been used to measure muck pile movement including poly-pipe, chain and sandbags but these have been either inaccurate or impractical. The Julius Kruttschnitt Mineral Research Centre, JKMRC, has developed an electronic blast movement monitor that provides accurate three-dimensional movement vectors following a production blast. From this information, the ore block boundaries in the blasted bench can be adjusted to compensate for the measured movement and then ore recovery can be optimised. Following initial development of the prototype technology, the JKMRC further developed and demonstrated the system in actual production blasts at an open pit gold mine operated by Placer Dome Inc.

Jan 1, 2005

By Robert W. Waytulonis

The Federal Bureau of Mines contacted 29 organizations--mine maintenance departments and equipment manufacturers--concerning service experience and construction of diesel exhaust-gas water scrubbers. Scrubbers are used primarily on mobile diesel-powered mining equipment subject to 30 CFR 36. Because the scrubbers cool exhaust gas and act as flame arresters, their failure would compromise safety in underground mines. Scrubber maintenance problems and frequency and modes of failure were identified, and construction materials and techniques were evaluated. Three failed scrubbers were randomly selected from two cooperating mines, and their modes of failure were determined. In conjunction with failure analyses, mine water and scrubber water solution samples were chemically analyzed to characterize corrosive properties. Sludge and mineral deposits and different types of corrosion and metal fatigue were identified as problems leading to scrubber failure. The corrosion process is explained; maintenance practices, construction materials, and manufacturing methods that could be used to reduce premature failures and allow longer effective scrubber life are identified; and basic changes in scrubber design are suggested. If type 304 stainless steel is used throughout the scrubber and regular maintenance is performed, long, dependable service can be expected. Other materials such as 304L, 316, or other more exotic steel alloys may be necessary under certain conditions.

Jan 1, 1982

By Mark F. Sindelar, Yi Luo, Hua Jiang, Michael T. Shook

"Convergence of roof and floor in underground mine openings is a common occurrence. This convergence not only adversely affects the ability of workers, equipment and supplies to travel through the mine, it also reduces the effectiveness of the mine ventilation system, which is essential for the dilution of methane gas and airborne respirable dust. While installing secondary standing supports to control floor and roof convergence, such supports, by nature, partially obstruct a portion of the airway. These added obstructions inhibit the ability of the ventilation system to operate as efficiently as it could by increasing the resistance in and reducing the cross-sectional area of the airway.This study introduces and demonstrates the benefits of The Eye CAN™ standing roof support, which controls floor and roof convergence and is less obstructive to air flow than conventional wooden cribs. Laboratory findings show that the normal resistance of a supported lined airway is reduced by using this new product from Burrell Mining Products, Inc., while providing the same roof support characteristics of an established product-The CAN®. Load vs. displacement curves generated from laboratory tests demonstrated that this new product behaves with the same roof support characteristics as others in The CAN product family. Ventilation data gathered from a simulated mine entry was then used for computational fluid dynamics (CFD) modeling. The CFD analysis showed an improvement with The Eye CAN versus other accepted forms of standing roof support.This proof-of-concept study suggests that, when using this new product made by Burrell Mining Products, Inc., not only will the convergence from the roof and floor be controlled, but airway resistance will also be reduced.INTRODUCTIONOne of the basic elements of underground mining is the necessity to support the mine roof. It is well-known that easier reserves have been mined so that today's underground mines present challenging conditions. Factors influencing roof support decisions include mine depth, mining method, overburden composition, and agency regulations. Mining engineers, therefore, have to balance three objectives: safety, engineering, and cost. While safety is obviously paramount, and engineering often complements safety, the cost effectiveness of any product, method, or device warrants additional consideration in today's harsh business climate. Avenues for adaptation and improvement are found at the intersection of the three objectives."

Jan 1, 2016

By D. C. Yates, G. V. Jolliffe

In the five coalfields of Staffordshire, there have been some 43 incidents of spontaneous fires and heatings which have required special attention in the past ten years. This total excludes incidents in the Thick Coal Seam of South Staffordshire, which was worked until 1967, and which was subject to an almost continuous series of heatings. The incidents have been classified to show the sites of occurrence, the contributory factors which may have caused them and the treatments applied to them. The remedial techniques, as practised in Staffordshire, are dealt with in detail, with particular reference to standard methods of stopping-off. Precautionary measures taken are described, including a "liability to spontaneous combustion" classification of all seams, and the setting up of an emergency organization with emergency stocks of materials and equipment. The paper is concluded by a few words on the organization and control at the time of an incident.

May 23, 1905

By Arden D. Fugate

The Federal Bureau of Mines conducted extensive studies on solid-state defluorination (laboratory scale) and tests on molten defluorination (intermediate scale) of siliceous fluorspars. The studies were made to develop a pyrohydrolytic process for liberating fluorine from offgrade fluorspars. Test results showed that more than 90 percent of the fluorine can be evolved by solid-state defluorination at 1,300° C., and more than 97 percent can be liberated by molten-state defluorination at 1,420° C. Solid-state defluorination conditions were established by conducting tests on mixtures of ceramic-grade fluorspars and high-purity silica flour. Pelletized mixtures were defluorinated under varying conditions of time, temperature, and relative concentrations of silica, calcium fluoride, and water. The effects of adding various amounts and combinations of aluminum oxide and iron oxide on defluorination were also studied. Investigations of solid-state defluorination indicates that the following two reactions are involved: 2CaF2 + 3SiO2 = 2CaSiO3 + SiF4, and CaF2 + Sio2 + H20 = CaSiO3 + 2HF, The second reaction is dominant, although significant defluorination can be achieved by the first reaction.

Jan 1, 1961

By Michael G. Zabetakis

The spillage of liquid diethyl ether in rooms at floor level and 3 feet above the floor resulted in flammable vapor-air mixtures in the immediate vicinity of the exposed liquido The liquid temperature was found to decrease by as much as 35° C., with a resultant decrease in vaporization rate. A search of the literature yielded numerous references to unstable peroxide (residue) formed by the autoxidation of ether. Such residues appear to constitute an explosion hazard in the condensed state.

Jan 1, 1962

By J. R. McWilliams

Several of the current concepts of brittle fracture involve consideration of the existence of defects or flaws. Griffith 1 observed that the tensile strength of brittle materials was several orders of magnitude less than might be expected from the calculated strength of the molecular bonds. He was able to show that the stress concentration at the tip of an elliptical crack is sufficient to raise the local stress level many fold. He therefore proposed that real materials do contain such stress risers in the form of minute cracks and that this accounts for the rather large difference between theoretical and actual strengths of brittle materials. The degree of stress magnification depends to a great extent upon the orientation of the crack with respect to the general stress system, and to the general geometry of the crack.

Jan 1, 1967

By George Burnhart

"Sonic drilling is a relatively new technology even though it has been in development since the late 1940s. It was initially funded by the U.S. petroleum industry and then, in the late 40s, Russian scientists worked on developing sonic drilling, their interest based on drilling rates 3 to 20 times that of conventional methods. In the early 1960s, the Shell Oil Company backed research that resulted in a down-hole device with a series of eccentric weights driven by drilling fluid to generate vibration. Hawker Sidley, in the early 1980s, developed the first modern prototype sonic drills in Vancouver B.C. and the North Star Drilling Company in Minnesota became the first contractor in the U.S. to operate sonic equipment in 1985. In 1994, North Star became a division of Boart Longyear, headquartered in Salt Lake City, Utah.What’s Unique about a Sonic DrillA sonic drill rig appears and operates very much like any conventional top-drive rotary rig. The key difference is that a sonic drill has a specially designed hydraulically powered drill head, containing oscillators, that generates adjustable high-frequency vibratory forces. The sonic head is attached directly to the drill pipe or outer casing, sending the high frequency vibrations down through the drill steel to the face of the drill bit. This creates displacement, fracturing or shearing action depending on the material being drilled. The oscillator uses two eccentric, counter-rotating balance weights or rollers that are timed to direct 100% of the vibration at 0 degrees and 180 degrees. An air spring houses the oscillators and separates the vibration from the drill rig itself. The vibratory frequency is controlled to suit operating conditions and to achieve optimum drilling rates.When the vibrations coincide with the natural resonant frequency of the steel drill rod or casing, a natural phenomenon called “resonance” occurs. It allows the rig to transfer timed vibratory energy into the top of the drill string, utilizing the natural stored energy of the steel. This causes the drill string to use inertia and act like a flywheel delivering tremendous amounts of energy directly to the bit face. In friendly overburden formations, a sonic drill rig can achieve penetration rates of one ft per second."

Jan 1, 2008