Search Documents

By T D. H McGrath, J P. Vaughan, J Heath, J J. Eksteen

A reliable laboratory method to characterise the response of free gold particles when subjected to flash flotation conditions has been developed by AMIRA P420 researchers at Curtin University. This test has been applied to assess the flotation recovery of gravity recoverable gold from free milling ores as well as synthetic ores featuring either a gravity concentrate or gold powder. Trends in free gold flotation kinetics as well as size and milling effects were identified for gold recovery, based on the different gold types, reagent dosage and residence time.CITATION:McGrath, T D H, Eksteen, J J, Vaughan, J P and Heath, J, 2013. Laboratory flash flotation trends for a variety of gold particles, in Proceedings World Gold 2013 , pp 357-366 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By T. Bertke

This document assesses the environmental aspects of a preliminary design for processing kaolin clay as the domestic resource for recovery of alumina by a hydrochloric acid leach-HCl gas induced crystallization process. The report covers waste sources, control measures, and potential environmental and health effects applicable to the process technology.

Jan 1, 1980

By T. M. Barczak

This U.S. Bureau of Mines report investigates shield mechanics and component stress development in a two-legged longwall shield for unsymmetric canopy and base contact configurations. Previous studies analyzed shield behavior for symmetric contact configurations. The goals of these efforts are to improve longwall support selection and design. This study provides vital information that will help develop improved procedures for performance testing of longwall supports and will benefit future research to improve support design through stress optimization and evaluation of failure mechanisms. Combinations of six canopy (three symmetric and three unsymmetric) and six base (four symmetric and two unsymmetric) contacts provided a total of 36 configurations for evaluation. Of these 36 configurations, 10 were eliminated because of fixture limitations or shield instability. Controlled vertical and horizontal displacements were applied by the Bureau's mine roof simulator to the remaining 26 configurations. Component responses were determined from pressure transducer and strain gage instrumentation in order to identify contact configurations and boundary displacements that produced maximum loading in each of the support components. This report describes these test results and provides conclusions relevant to critical contact configurations for performance testing of longwall supports.

Jan 1, 1990

By Wilbert J. Huff

The Explosives Division of the United States Bureau of Mines makes certain laboratory and field investigations that deal with explosions, explosives, ignition, and combustion, together with many related problems, such as the cause and prevention of fires, and certain fundamental scientific questions bearing upon the determination of the chemical and physical mechanisms underlying some of the important phenomena encountered. Its work on explosives has been particularly directed toward determination of the chemical and physical characteristics of explosives designed for use in coal mines and in a more limited way to those used in metal mines, tunnels, quarries, and other engineering operations. This testing is handled by two units of the Explosives Division, as follows:

Jan 1, 1937

By Peter Claus

In the last years, supported gold catalysts with particle sizes smaller than 10 nm have attracted a lot of attention. While gold bulk metal is rather inert in chemical reactions and, thus, is of low interest for catalysis, highly dispersed gold particles supported on oxides as TiO2 or ZrO2 show surprisingly high activities in some reactions important for the chemical industry. The oxidation of carbon monoxide at low temperatures is mainly used as model reaction to study the unusual properties of gold catalysts [1]. On the other hand, to evaluate the catalytic potential of gold, other chemical reactions which allow to control also the selectivity have to be considered. The selective hydrogenation of ???-unsaturated aldehydes to allylic alcohols is of both commercial relevance (e.g. in fine chemical and pharmaceutical intermediate production) and specific scientific interest [2]. Note that thermodynamics favors hydrogenation of the C=C over the C=O group (stronger negative free reaction enthalpy of 35 kJ/mol), and for kinetic reasons the C=C bond is more reactive than the C=O group. Thus, in the presence of most of the conventional hydrogenation catalysts, based on Pt, Rh or Pd, -unsaturated aldehydes such as acrolein and crotonaldehyde are hydrogenated predominantly to the saturated aldehydes and only to a minor extent to unsaturated alcohols. Therefore, it is desirable to find catalysts which are able to control the intramolecular selectivity by hydrogenation preferentially the C=O group while keeping the olefinic double bond intact (Fig. 1).

Oct 1, 2003

By J. E. Wilson

A bench-scale expansion tester using 71 grams of coal was developed to determine the practicability of an apparatus of this size to investigate the effect of variables such as oxidation, blending, bulk density, inerts, size consist, petrographic differences, and rate of heating on the expanding properties of coal. The value of this tester is shown by the correlation that exists between its results and those of the larger scale sole-heated oven expansion apparatus used in commercial plants. From tests on 32 coals the standard error of estimate for predicting sole-oven results from bench-scale results is ± 5.3 percentage points. A standard deviation of the difference between pairs of tests in the latter apparatus of ± 2.1 percentage points was determined for 31 samples. In the sole-heated oven test the expansion of a coal at constant pressure is directly proportional to the dry coal bulk density. Tests in the bench-scale tester show a similar relationship between expansion and bulk density. When the blending ratios of high-and low-volatile coals are varied, similar changes in expansion are observed in both the sole-heated oven and the bench-scale tester. Therefore, the effect of other variables on expansion should be similar in the latter apparatus.

Jan 1, 1960

By K. E. Soroka

More than 500 fires are now burning in abandoned coal waste banks and coal deposits in the United States. Once established, such fires can burn for decades, and extinguishing them by conventional methods such as surface sealing to exclude air, excavation to remove fuel, or flushing to cool the fire zone is usually difficult and always expensive. Burnout Control, a technique developed by the Bureau of Mines for the control of abandoned coal fires, involves the accelerated combustion of coal in place with total management of the heat and fumes produced. A burning waste bank or mine is placed under negative pressure relative to the atmosphere, and heat and combustion products are drawn from the combustion zone through an exhaust ventilation system. Heat produced appears as sensible heat in the exhaust, at temperatures as high as 1,0000 C (1,832° F), and could be recovered for the production of steam, hot water, process heat, or electricity. The Bureau's first held field demonstration of Burnout Control was at Calamity Hollow in Allegheny County, PA (near Pittsburgh). Calamity Hollow was the site of an underground mine in the 1900's and was surface mined in the 1940's. In the winter of 1961-62, a fire of undetermined origin was discovered in the exposed coal. In 1963, the Bureau constructed a trench barrier around the fire and a surface seal over the affected area. The fire was isolated but not completely extinguished. In 1979, when the Bureau began work on the Calamity Hollow Mine Fire Project to demonstrate controlled burnout, the fire was still smoldering on the hot side of the trench barrier. The project, which was begun in December 1979 and ended in July 1982, consisted of the design, construction, operation, and subsequent dismantling of a Burnout Control ventilation system. This report is the fifth in a five-part series that describes the Calamity Hollow Mine Fire Project. The first report, part 1, describes the design and construction of the field installation. Part 2 will present the results of a continuous 4-month burnout operation. (Because part 2 involves the analysis of a substantial body of data, it will not be published until after publication of parts 1, 3, 4, and 5.) Part 3 describes the instrumentation used to control and monitor the progress of the burnout operation. Parts 4 and 5 deal with the closeout phase of the field demonstration. Part 4 describes the procedure used to quench the fire, and this part (part 5) describes the final excavation and backfilling of the heated zones. The reports in this series document the Calamity Hollow controlled burnout demonstration which showed that (1) controlled in situ combustion is a feasible method for controlling underground fires in abandoned mines, (2) the resultant thermal exhaust output is sufficient for energy utilization, and (3) water injection-fume exhaustion is a potentially effective method for cooling large underground fire zones. Further investigations of both Burnout Control and the water-injection-fume exhaustion quenching procedure are planned.

Jan 1, 1986

By Nicholas J. Grant, H. C. Chang

TRANSCRYSTALLINE fracture surfaces of the cleavage type have been examined by microscopy and X-rays for several metals.' These investigations revealed that the fractured surfaces were not flat and invariably had cleavage and other deformation markings on them. On the other hand, the study of inter crystalline fracture surfaces has been limited. Perryman, in a recently published paper on the inter crystalline fracture of ß-brasses,' found that a thin layer of heavily deformed metal was invariably associated with these surfaces. Furthermore, the thickness of this layer was found to depend on the orientation of the grain boundary surface with respect to the applied stress. The mechanisms of grain boundary sliding and intercrystalline fracture have been presented in two previous papers,which described certain aspects of the deformation of a 20 pct Zn-A1 alloy. It is the purpose of this paper to present some observations on the structure of intercrystalline fracture surfaces and to correlate the structure of such surfaces with the mechanism of intercrystalline fracture. Experimental Techniques—The high purity 20 pct Zn-Al alloy was generously supplied by the Research Laboratories of the Aluminum Co. of America. Two sizes of specimen were used; the first had two parallel flat surfaces of dimensions 1x0.17x0.09 in. and the second was round with a 0.25 in. diam. A grain diameter of 1 to 3 mm was obtained by annealing the specimens at 1000°F for 24 hr. The specimens were then air cooled. The specimens were subjected to creep at 500°F and 2300 psi. The rupture times ranged from % to 3 hr, with one room temperature tensile test. It has been mentioned previous1y" that the intercrystalline fracture surfaces of this alloy, when tested under the conditions given above, are sharply defined. In the optical examination of the fracture surfaces, whenever possible, magnifications of at least X250 were used. The locations of the regions examined, both optically and by X-rays, were selected to give several fracture surface orientations with respect to the stress axis and to the specimen surfaces. This was possible for the X-ray studies since the grain diameters were large compared to the X-ray beam. A film to specimen distance of 3 cm, a 1 mm pinhole and Cr radiation were used for the Laue back reflection pictures.

Jan 1, 1957

By Wilbur I. Duvall

In a review of so 40 papers on damage to residential structures resulting from blasting, only 3 were found that present data on the observed amplitude and frequency of the vibration levels produced by blasting together with an observed degree of damage to a residential structure. The data from these three reports have been analyzed statistically to determine if one of the quantities, displacement, velocity, or acceleration, is more reliable than the others for estimating the degree of damage to a residential structure. From this analysis the conclusion is drawn that a given degree of damage to a structure is most closely related to the magnitude of the particle velocity of the wave motion passing thru the earth at the structure location. On the average, only minor damage it observed for peak particle velocities of 5.4 inches per second, and major damage is observed for peak particle velocities of 7.6 inches per second. When the spread of the data is taken into consideration, the following statement can be made: Wave motions that have a peak particle velocity in excess of 2 inches per second have a fair probability of producing some damage to structures, whereas wave motions that have a peak velocity less than 2 inches per second have a very low probability of causing any damage. Therefore, the recommendation is made that vibration levels in the vicinity of residential structures should be maintained below a peat particle velocity of 2 inches per second. The above criterion for safe blasting is considered to hold over a wide variety of soil and rock conditions because the original data were obtained for a wide range of soil and rock conditions and on various types of residential structures. INTRODUCTION Ever since explosives were discovered and developed for mining purposes, there has existed the problem of what effects the air and ground vibrations resulting from blasting have on structures of various types. This problem is

Jan 1, 1962

THE old mill erected by the .Irvinebank Company consisted of 10 heads of stamps (850 lb.), rock-breaker, Hartz jig, two Krupp tables, two Luhrig vanners, three sand-pumps, one mixer; six flotation vessels, and the necessary settlers. Power was supplied by a small colonial-type boiler, and 10-in. x 15-in Tangye engines. The ore was darted from the mines to the mill and hand-fed, into the rock-breaker, and the broken product elevated into the batter bins and fed into the stamps, the pulp from the stamps passing to a classifier, the spigot to jig, tables, and vanners, the overflow from the classifier passing to settlers. After the removal of bismuth-wolfram concentrates, the pulp was pumped to the molybdenite flotation plant and the olybdenite recovered by flotation.A commencement was made with the erection of the first unit (20 heads) of the new mill in August, 1917, and milling and concentrating commenced in February, 1919.

Jan 1, 1920

By E. G. Kelly

This paper describes the performance of a modern compound trough profile spiral that is optimized for fine coal cleaning. Reduced performance (Tromp) curves are presented to compare these new spirals with older designs, as well as with other commonly used coal cleaning equipment. As an aid to equipment selection and circuit design, data are also presented to show how variables, such as flow rate, pulp density, and particle size affect efficiency and the separation specific gravity.

Jan 1, 1984

By Ulf B. Andersson, Christina Dahnér-Lindkvist, Bruno Figueiredo, Jessa Vatcher, Jonny Sjöberg, Joel Andersson

Hydraulic fracturing to precondition the rock mass in high seismic risk environments has great potential. Unfortunately, there are many unanswered questions about how to best implement a hydraulic fracturing program at individual mine sites, and even how to best use our engineering tools to evaluate these plans. To give the hydraulic fracturing field tests at LKAB’s Kiirunavaara Mine the best chance of success, fully-coupled, discontinuum numerical modelling Itasca’s 3DEC code was used together with statistical simulations of the fracture network. For modelling purposes, it was assumed that hydraulic fracturing successfully reduces seismic risk through 1) the creation of hydraulic fractures along a plane at each injection site, and 2) activation of existing discontinuities. A variety of scenarios for the mine were evaluated, which focused on site specific uncertainties (such as the spacing of the pre-existing discontinuities) and practical solutions (such as the hydraulic fracture spacing, selection of injection medium, and hydraulic fracture site location relative to production). The discrete fracture network (DFN) realizations were developed using available statistical data for discontinuities near where hydraulic fracturing was planned.

Apr 26, 2022

By Seffen Leppla, Rolf Katzenbach, Matthias Seip

"Abstract The economic and safe design of deep foundation systems in difficult soil conditions is based on a reduction of construction material used, construction time spent, energy consumed and a high-level modelling of the soil-structure-interaction. The special foundation system Combined Pile- Raft Foundation (CPRF), in-situ load tests on the construction site and a sufficient soil investigation allow cost optimised constructions. In any case at challenging projects the observational method has to be applied for verification and quality control of the design. Regarding the 4-Eye-Principle as basis of the quality control management an independent peer review of the planning, design and construction phases is the guarantee for safety, serviceability and optimisation of all projects. Main execution standards for the construction of deep foundations based on the Eurocode 7 are summarised and discussed. The paper presents the basics of the safe and qualified design and construction of foundation systems including quality assurance. The application in engineering practice is shown on achallenging project of high-rise buildings with difficult boundary conditions.IntroductionThe construction of deep foundation elements in inner cities are special challenges due to the limited space for the construction works and the effects on existing buildings (Figure 1).An economic and safe design of deep foundation systems in difficult soil conditions is based on the following main aspects:•,qualified experts for planning, design and construction•,interaction between architects, structural engineers and geotechnical engineers•,adequate soil investigation•,design of deep foundation systems using the Finite-Element-Method (FEM) in combination with•,enhanced in-situ load tests for calibrating the soil parameters used in the numerical simulations•,quality assurance by an independent peer review process (4-eye-principle) combined with theobservational method if necessary"

Jan 1, 2014

By W. P. Yant

Canister-type gas masks have become an essential part of the equipment of many industries not only for use in emergencies, but also in performing normal operations of industrial processes and procedures, particularly where ventilation is not practically or economically feasible. They are also used widely for enhancing safety of operations which previous to the development of gas masks had been performed in harmful atmospheres. Since the inception of industrial gas masks the Bureau of Mines has been actively engaged in endeavoring to increase the efficiency and safety of these devices and this bureau has become a source of advice to manufacturers in producing devices of good quality and to industry in the proper selection and use of these devices. In order to give first-hand information and keep current with the demands and needs of industry it is necessary to perform investigations from time to time. This report deals with tests of certain types of commercial gas-mask canisters for protection against mercury vapor.

Jan 1, 1932

By Donald E. Scheck

Blasting practices based on sound engineering principles are well established but the successful application of these practices requires accurate information about the overburden geology and close supervision of the drilling and blasting operations. Good design alone is not sufficient to insure good results, but the process may be difficult to control unless steps are taken to measure the variables and to provide management and the operators with the information they need to establish and maintain control. Satisfactory blasting can be defined as loosening and fragmenting the rock so that it can be handled by the excavating equipment, while at the same time, governmental regulations on air blast and ground vibrations are not violated. Optimum practices achieve these objectives at the lowest combined cost of the drilling and loading operations and the blasting materials. Total system optimization, that is, taking into consideration the effect of fragmentation on the cost of operating and maintaining excavating equipment as well as drilling and blasting costs, probably is not a reasonable goal at the present time.

Jan 1, 1984

By M. Zaki El-Sabban

Tables of chemical thermodynamic properties for the ideal gas state from 0° to 1,000° K are reported for eight alkanethiols, three cycloalkanethiols and arylthiols, six thiaalkanes, two dithiaalkanes, three thiacycloalkanes, and three thiophenes. They are based on current physical and thermochemical constants and definitions, reliable vibrational assignments, and the latest insights into molecular structure and energetics.

Jan 1, 1970

By B. E. MacNab

During the past several years, Raymond Kaiser Engineers has prepared numerous studies concerning the technical and economic feasibility of coal exporting facilities in the western United States. Perhaps the most striking conclusion to be drawn from these efforts is that many people underestimate the complexity of the highly competitive, dynamic coal marketing system which includes coal loading terminals as an essential but relatively low-cost link in the energy production and delivery chain. The title of this paper, "The Status of Western United States Coal Ports - An Economic Assessment," should not delude anyone into thinking that the future of western U.S. coal- exporting ports has now congealed into a well- defined economic plan. As this paper will demonstrate, the situation is complex and more dynamic than ever and promises to remain so into the late 1980's.

Jan 1, 1982

By P. K. Sollars, M. A. Alspaugh

In May of 1996, Twentymile Coal Co. began Longwall mining in the Foidel Creek Mine's East Mine District. These Longwall panels are some of the longest in the world (5.48 km/18,000 ft) with very difficult and challenging geometry. The conveyance system is 1,800 mm (72 in) wide, has a 4,500 mtph (5,000 stph) capacity and employs multiple tripper drives. The trippers include traditional powering designs as well as unique regeneration and braking designs. Several components were developed specifically for this application including a mobile tail brake. Control algorithms were carefully developed and tested via computer modeling. A world production record was achieved in the third month of operation and over 1 million tons were mined in June 1997.

Jan 1, 1998

By William J. Campbell

Expansion measurements of platinum, added as an internal standard, are used for thermal calibration of X-ray cameras and diffractometers. Accuracy of the temperatures derived by this technique depends on the precision of expansion measurements and the reliability of reference expansion data. Temperature measurements to ± 1° C. require ?d or ?a to be determined within ± 0.001 percent. Selected expansion data are concluded to be reliable to 2° C., 5° C., and 25° C., over the temperature ranges 0° C. to 700° C., 700° C. to 1,000° C., and 1,000° C. to 1,700° C., respectively. Tabular expansion values from 25° C. to 1,700° C. in 2° C. intervals were calculated from the following equation; Expansion, percent = [8.91 + 1.28 x 10-3(t-25) + 0.04 x 10-6(t-25) ] [t-25.104 ] These tabular values facilitate future corrections of published temperatures as more reliable expansion-temperature data become available.

Jan 1, 1962

By D. Kruse

Top-down constructed large-diameter (up to 90 m or 300 ft) shaft design and constructability issues present an interesting suite of challenges and opportunities highlighted in this paper. The study covers 2D and 3D finite element models used to analyze various failure modes, evaluate the shaft liner and internal structures' response to seismic loading, assist in segment design and assess final structural design tradeoffs. Efforts to achieve economic advantage over conventional heavy civil practices have prompted innovative solutions for ring and segment design, ring build assembly and annulus backfill grouting. Intended for soft ground conditions, relationships between soil parameters and structure design are also explored. Mining Engineering, 2011, Vol. 63, No. 9, pp. 81-88. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011