Search Documents

By M. J. Ferrante

Laboratory-scale tests were undertaken to examine several electrolytes for possible use in separating nickel and cobalt from products being prepared at Nicaro, Cuba. The most extensive work was done with nickel sulfate-ammonium fluoride, ammonium fluoride, ammonium sulfate, and nickel sulfate-boric acid electrolytes. All four electrolytes exhibited some selectivity for dissolving nickel carbonate from Nicaro basic carbonate used for regeneration. The nickel sulfate-ammonium fluoride electrolyte exhibited less selectivity for dissolving nickel carbonate from Nicaro basic carbonate than it did from synthetic mixtures. Ammonium fluoride leaching experiments showed that a low concentration and high temperature gave a good nickel extraction with C. P. reagents; however, this was not confirmed in tests using Nicaro basic carbonate. Electrolytic tests employing ammonium fluoride leach liquors gave no further separation, since approximately 90 percent of the cobalt was deposited at the cathode with the nickel.

Jan 1, 1958

By K. Yathavan

Fracturing of rock at low stress levels can be a source of unexpected problems in rock engineering: • the resulting instability can be a safety hazard; • in very brittle rocks it may be associated with violent failure of the rock and strainbursting (rockbursting); • it usually leads to an unexpected requirement for rock support, with time and cost implications; • in rock boring projects, it may result in fracture of the rock ahead of the bored face and in the walls of the bore behind the face. This may lead to cutter head vibration, increased cutter wear and consequently decreased performance and increased costs. Examples of situations in which fracturing of rock at very low stress levels has been observed will be described. This will include details or estimates of the in situ stress magnitudes and the rock strengths involved. La brisure de roche sous faibles contraintes peut être l’origine de problèmes inattendus en génie minier : • L’instabilité résultante peut devenir un danger • Elle peut provoquer des éclatements violents des roches fragiles • Elle nécessite souvent une infrastructure de soutien de la roche, ayant des implications sur les coûts et les délais • Les forages de la roche peuvent provoquer une brisure de celle-ci au niveau de la surface forée mais ainsi à l’intérieur de la roche, causant parfois des vibrations et une fatigue de la tête de forage, induisant une baisse de performance et un accroissement des coûts. Nous avons décrit ci-après des exemples de situations de brisure de roche sous faibles contraintes. Cette description comprend des détails ou des estimations des forces et des contraintes impliquées. Cette étude représente la base du travail de recherche effectué sur le phénomène. ißbildung im Gestein unter niedrigen Stressbedingung kann eine mögliche Ursache sein für unerwartet auftretende Probleme in der Felsmechaniklehre: • Die resultierende Instabilität stellt ein mögliches Sicherheitsrisiko dar; • In sehr sprödem Gestein kann es verbunden sein mit einem plötzlichen und gewaltsamen Zerfall des Gesteins; • In den meisten Fällen ist eine nicht eingeplante Gesteinsabstützung erforderlich, und damit ein Zeit- und Kostenaufwand verbunden; • Bei Bohrungsprojekten kann es dazu führen, daß es während des Bohrvorganges zu einer Rißbildung im Gestein hinter und vor der gebohrten Felswand kommt. Dies kann Bohrkopfvibrationen, eine erhöhte Bohrkopfabnutzung und folglich eine Bohrleistungssenkung, sowie Kostenerhöhung zur Folge haben. Das Phenomen von Gesteinsrißbildung unter niedrigen Stressbedingung wird anhand von einigen dokumentierten Beispielen erörtert. Diese beinhalten zudem Details oder Schätzungen bezüglich der Stärke des in situ Stressfeldes, sowie der gegebenen Gesteinsstärken. Die mit diesem Beitrag dokumentierten Ergebnisse formen eine Grundlage zur weiteren Forschung dieses Phenomens.

Jan 1, 2003

By Nadir Ansari, Brian W. Wilson, Marina S. W. Li

"A hybrid shoring system consisting of cast-in-place soldier piles with Cutter Soil Mixing (CSM) infill panels was constructed for temporary support of a 19.8 m (65 ft) deep excavation in Vancouver, British Columbia, Canada. Deep Mixing (DM) was completed up to 9.7 m (32 ft) in fill, peat, wood waste and clayey silt with embedment in dense till, and soldier piles constructed through the dense till extending to below final excavation level. Two trial CSM panels were installed ahead of production to assist with developing the termination criteria of the CSM panels in the dense till. The constructed depth of the CSM panels was based on interpretation of real-time monitoring data obtained through the Bauer B-tronic system. Inclinometer monitoring data from two CSM panels and two soldier piles, as well as soldier pile survey target data was used to assess and monitor the performance of the hybrid shoring system throughout bulk excavation. The objectives of this paper are to provide an overview of the design and construction aspects of the hybrid DM shoring system and to present inclinometer and pile target data to demonstrate the lateral performance of the CSM infill panels and soldier piles. This paper also discusses the merits of using real-time monitoring data as part of the engineering decision-making process for validating CSM panel construction. BACKGROUND A hybrid DM shoring design was recently completed for a high-rise development in downtown Vancouver, British Columbia for temporary support of a five level basement excavation. Deep mixing was proposed by the excavation and shoring design-build team as the preferred method to construct infill panels between soldier piles because of the speed at which the shoring system could be constructed in variable fill, peat, wood waste and overburden compared with traditional secant piling methods. The development site is generally a truncated triangle in plan, with the longest side of the triangle being approximately 115.7 m (380 ft) long and the two shorter sides being approximately 71.6 m (235 ft) (Hybrid Shoring Wall 1) to 75.0 m (246 ft) (Hybrid Shoring Wall 2) long. The site is bounded by an existing bridge off-ramp structure along its longest side, and by city streets on the other two sides, as shown in Figure 1. The truncated section is approximately 16.8 m (55 ft) (Hybrid Shoring Wall 3) long. Due to project constraints, the hybrid DM and soldier pile shoring system was only proposed for the two shorter sides of the triangle and the truncated section. Traditional secant piles were installed for the longest side. This paper focusses on the hybrid shoring system. A typical detail showing the CSM infill panel with the soldier piles is presented in Figure 2."

Jan 1, 2017

By d&apos, Dennis V. Andrea

The Bureau of Mines and El Paso Mining and Milling Co. conducted a cooperative in situ leaching research program at the Emerald Isle mine near Kingman, Ariz. The objective of this research was to develop in situ leaching methods for 200,000 tons of ore exposed in the pit bottom and also 3,000,000 tons of ore under 200 feet of overburden adjacent to the pit. The research included core drilling for fragmentation analysis, inplace permeability testing, seismic surveys, blasting tests, blast vibration measurements, inplace leaching, and ground water monitoring. A l5,000-ton test area in the pit bottom was blasted and leached inplace for 117 days. This successful test was followed by leaching 100,000 additional tons of unblasted pit bottom ore. Two test blasts, under 205 feet of overburden and extending to 290 feet, were detonated in an area near the open pit. The second blast was detonated because the first blast did not create adequate permeability for leaching. Pit bottom leaching was discontinued and the test area under 200 feet of overburden was not leached because the company terminated operations at the Emerald Isle mine. Based on the research completed, an expanded in situ leaching system was designed, but not implemented, to recover copper from a 1,500,000-ton area at the Emerald Isle mine.

Jan 1, 1977

By James D. Hall

THIS essay deals with the materials and methods used in the waste filling of scopes in Canadian mines, with especial reference co the methods used at the Sullivan mine, Kimberley, B.C. The author would like to thank members of the staff of the Sullivan mine for information obtained, and acknowledges material from the following publications: Waste Filling of Stopes: Information Circular 6816, U.S. Bureau of Mines. Mining Methods and Practices at Lake Shore, by Leslie S. Weldon; Trans., C.I.M. & M., Vol. XXXIX, 1936, pp. 142-202. Development and Mining (at the Mcintyre Mine), by D. E. Keeley; Eng. & Min. Journal, November, 1933. INTRODUCTION Although mining in Canada is a relatively youthful industry, many of our mines have reached a stage of extraction which requires waste filling, both as a means of support and co make possible the winning of ore that would otherwise have co be left in the mine. Fill may be used at regular intervals as one of the cycle of operations, as in cur-and-fill and square-set scoping; or it may be introduced into a completed stope co provide permanent support for overlying rock formations, and co permit mining of pillars of valuable ore. Waste fill is sorted in resuing, which is a form of cut-and-fill scoping employed in narrow veins.

Jan 1, 1937

By E. G. Davis

Under a memorandum of agreement with Reynolds Metals Co., Richmond, VA, the Bureau of Mines studied the problem of corundum formation on refractory linings in aluminum recycling furnaces. A laboratory test was developed for evaluating refractories in contact with molten recycled aluminum and identifying the mechanism of corundum formation. A test apparatus was designed and constructed to evaluate the performance of refractory samples. Corundum mechanism formation studies indicated that corundum formed on refractories when there is metal penetration. Once corundum forms, it acts as a wick allowing the molten aluminum to move to the surface where it is oxidized, thus causing further growth of the corundum. Phosphoric acid treatment or a spinel mortar coating prevented corundum formation on the 70-and 90-pct-A1203 refractories.

Jan 1, 1988

By Keith Schaeffer

This paper presents a history of the planning, engineering and construction completed for the railroad tunnel crossing part of the West Elizabeth Avenue Storm Drainage Project, undertaken to relieve flooding within the West Elizabeth Avenue area in Linden, NJ. The Railroad Crossing Contract is part of the larger Linden Drainage Improvements Project consisting of a new gravity storm sewer system. The improvements are required to provide additional storm drainage for the City of Linden and the Merck Pharmaceuticals manufacturing facilities in the City of Linden.

Jan 1, 2008

By K. Ananthanarayanan, R. I. L. Guthrie, S. A. Argyropoulos

"The low cost and availability of micro-computers and their peripherals provides the metallurgical engineer with the opportunity to use such computers in a wide variety of applications. In this paper, the authors describe the development of a low cost data acquisition system capable of measuring up to 8 analogue channels at a sampling rate of up to 5000 measure mentsper second. This system is equipped with proper hardware and software so that the micro-computer can be linked to a central computer facility such as the McGill System for Interactive Computing (MUSIC). This central computer facility is supported by an AMDAHL V7 computer. Using the present interface, communication rates between the microcomputer and the central computing facility can be as high as 9600 (baud).The above mentioned data acquisition system is currently used for monitoring dissolution kinetics of ferro-alloy additions in liquid steel. In addition to this, special software has been developed which enables the user of this system to monitor solidification rates of ingots, etc. As economic considerations are always important, comparisons have been made with existing recorders which show that the cost Of the present system is only 30 per cent more than a two-pen strip chart recorder.RESUMELa disponibilité et le bas prix des micro-ordinateurs et de leurs périphériques permet à l'ingénieur métallurgiste d'utiliser de tels ordinateurs pour diverses applications. Dans ce rapport, les auteurs décrivent le développement d'un système d bas prix pour l'acquisition des données, capable de mesurer jusqu'à huit canaux analogues jusqu’à une vitesse de 5000 mesures par seconde. Ce système est équipe avec son propre ""hardware"" et ""Software"" qui relient le micro-ordinateur d’un ordinateur central, comme le système de McGill pour computations réciproques (MUSIC). Ce central d'ordinateurs est soutenu par l'ordinateur AMDAHL V7. Utilisant cet "" interface"", la vitesse de communication entre Ie micro-ordinateur et l'ordinateur central peut atteindre jusqu'd 9600 (baud)."

Jan 1, 1980

By Robert M. Doerr

The research objective was to determine the effect of aluminum alloy additions on the oxidation behavior of cobalt-nickel alloys. Thirty high-purity alloys were reacted with 02 at 0.5 atm at 1,351°, 1,389°, and 1,429° K in a volumetric apparatus for about 300 min. The alloy compositions consisted of Co-Ni master alloys (0, 22, 50, 70, 91, and 100 wt pct Ni) with aluminum additions of about 0, 1, 2, 4, and 8 wt pet. Large early deviations from, or changes in, the parabolic rate constant were encountered, but in most cases, the reaction rate declined approximately in accordance with the parabolic rate law. A sharp peak in the parabolic oxidation rate constant was observed for specimens containing a to 22 percent nickel and 1 to 2 percent aluminum at 1,351° K, and the rate constants for these compositions were lower at the higher temperatures. Specimens containing 8 percent aluminum reacted far more slowly than did any of the others.

Jan 1, 1971

By Maria I. DeRosa

This Bureau of Mines report describes the Automated Breathing Metabolic Simulator and its hardware and software systems with emphasis on the role exerted by the software program subroutines in controlling the hardware mechanisms during the simulation of man's respiratory and metabolic functions.

Jan 1, 1978

By Ruipeng Qian, Pengfei Wang, Guorui Feng, XianJie Du, Jun Guo, Yuxia Guo, Tingye Qi, JinWen Bai

"A numerical modeling was conducted to describe the behavior of overlying strata on the longwall top coal caving face for exploitation of a 16.8 m thick coal seam. Three typical structural models, including the Cantilever Structure (CS), Lower Cantilever and Upper Hinged Arch Structure (LC&UHA), and Lower Arch and Upper Voussoir Beam (LA&UVB), were developed. Based on mechanical analysis of the different structures of the key strata, and considering the behaviors of the broken igneous rock strata, a method was proposed and applied to estimate the structures of the overburden strata. The results had been verified by a field micro-seismic monitoring test. The paper provides a foundational method to determine the shield loadings for the top coal caving longwall face.INTRODUCTIONLongwall top coal caving (LTCC) is a highly productive underground mining technology which has been widely applied to the exploitation of the thick coal seams in China and other countries due to its high efficiency (Ju and Xu, 2013; Ju, Xu, and Wang, 2011; Liu et al., 2009). In recent years, a large amount of research on mining pressure forecast, strata control, and mechanical equipment improvement of the LTCC technology has been carried out, which greatly advances the field application of the technology (Liu et al., 2009; Yu, 2016; Dou et al., 2014; Feng et al., 2011; Chen and Li, 2011; Yin, Yan, and An, 2008). In 2006, the LTCC technology was first applied to the exploitation in a 20 m thick coal seam at the Tashan Coal Mine in China (Yan et al., 2011). Ten years of mining at the Tashan Coal Mine has highlighted the importance of the support management in controlling the roof strata on the extra-thick LTCC face. The mining pressure is closely related to the structural features of the overlying strata and its movement laws (Yu, 2016; Dou et al., 2014; Feng et al., 2011). However, the distributions of three zones—caving zone, fracture zone, and deformation zone—on the fully mechanized caving longwalls changed significantly with the increase in thickness of the coal seam (Chen and Li, 2011). The behavior changes of the roof strata led to abnormal pressure in the mining face and resulted in the difficulty of surrounding rock control (Yin, Yan, and An, 2008; Liu et al., 2009; Yan et al., 2011; Gong and Jin, 2008). Therefore, the theoretical research focused on the behavior of overlying strata to reveal the laws of mining pressure has important theoretical significance and practical value.Many classical studies (Qian and Shi, 2003; Feng, 2010; Yu, 2015; Yu, Yan, and Liu, 2012) had been done to describe the behavior of overlying strata in the mining process. It has also been reported that magma intrusion causes an important effect on the surrounding rock, coal, and methane (Wang et al., 2005; Liu et al., 2007). On the one hand, the property and structure of the coal seam was obviously changed by the magma intrusion and resulted in a potential danger of a gas outburst during the mining process (Chen et al., 2012; Wang et al., 2014). On the other hand, the hard igneous strata and the joints occurred with the magma cooled, causing an abnormal behavior of overlying strata and resulting in a series of dynamic disasters during mining (Xuan, Xu, and Lu, 2014; Lu et al., 2016). In fact, many coal fields in China are intruded by igneous sill, including the Datong, Shuozhou, Huainan, and Xuzhou coal fields (Chen et al., 2014; Wu, 2011). The 3–5 coal seam at Tashan Coal Mine in Datong coal field is very thick and is intruded by a large area of layered lamprophyre rock. Face falls and shield failures occurred frequently during the face retreat."

Jan 1, 2019

By M. Roy

Safety and stability of underground coal mine workings are always in danger when opencast mines are operating in close proximity. A study was conducted to investigate the level of vibration generated from opencast blasting at similar distances on the surface as well as in the nearby operating underground coal mine openings. Eight blasts were performed and nineteen vibration data were recorded on the surface behind the opencast blasting face and also in underground openings at similar distances. It was observed that magnitude of vibration recorded on the surface were more than those recorded in underground.

Jan 1, 2007

By R. F. Hochstein, A. J. Neale, B. C. Flintoff

"Process control technology holds very significant potential benefits for many mineral and coal processing plants. The impact can be expected in terms of performance improvements (e.g. increased throughput, better quality control, higher availability), through reduced operating costs (e.g. lower reagent consumptions, manpower reductions) and in the form of intangibles (e.g. reduced vulnerability to manpower turnover, increased productivity in the user group). However, the installation of a process control system will represent considerable capital expenditure and will generate an operating cost. No management team would approve the funding for such a project without some reasonable measure(s) of the profitability of a proposed system. This paper describes a methodology for addressing the justification problem. Of particular interest is the approach to quantifying performance improvements, frequently found to be the predominant benefit of process control.INTROPUCTIONProcess control has become widely recognized as an essential component of any processing operation. It has direct impact on productivity, process efficiency and product marketability. The reported pay backs associated with successful installations underscore this observation. As a consequence, many operators who have little in the way of process automation are looking to initiate control projects, while those who currently enjoy some level of automation are looking to upgrade existing control systems (= process + instrumentation + hardware + software + operators + support). While the emphasis here would appear to be on retrofit process control projects, new plants, or those currently in the design stage, will usually find themselves in one of these categories shortly after startup 1."

Jan 1, 1990

By Maria I. De Rosa

High temperatures encountered by mine rescue teams during emergency situations may cause severe physiological strain, hindering the men from carrying out rescue and recovery missions. A prototype ice-cooling garment (ICG) was developed by the Bureau of Mines to alleviate physiological strain due to heat stress. The effectiveness of the garment was tested with acclimatized and unacclimatized subjects at a typical work rate (1,200 Btu/hr) expected during rescue operations and at various hot environments (97° to 113° F dry bulb and 80° to 89° F wet bulb). During exposures with the ice cooling garment, the subjects were able to maintain a safe deep body temperature of 100.4° F or below Without the garment, the deep body temperature rose beyond values of 100.4° F, a condition considered unsafe for continuous work in hot conditions. Both heart rate and skin temperature values were lower while wearing the ICG. Subjective observation also indicated a marked benefit by wearing the ICG.

Jan 1, 1976

By Daniel T. Brian, O&apos

Exploration targets and results in the mining industry are commonly summarized in terms of tonnage and grade. Business appraisals require, as additional information, the expected profit or loss implied by the physical summay. The early incorporation of knowledge gained through financial analysis computations can provide a means for economically resolving many common exploration and development problems. Examples of such applications from the activities of exploration planning, reconnaissance, land acquisition, and development planning are presented. While prospecting for mineral deposits, geologists are frequently asked what they hope to find or have found. The response is usually descriptive, such as "50 million tons of 1% copper," and the economic implications are deferred until a capital investment decision is required. At that time, a financial analysis integrating the four analysis components is completed. These components are: 1) Tonnage and Average grade above cutoff grade 2) Capital and operating costs 3) Product value 4) Appropriate profit or loss accounting Close examination of these components reveals that there is no intrinsic reason for avoiding financial analyses at earlier stages in exploration, as long as the uncertainty of the estimate is realized. Tonnage and average grades are commonly estimated at early stages in exploration. For this component, the appropriate cutoff is the major uncertainty. Capital and operating costs are difficult to estimate before detailed quantitative information is available, but estimates useful for the types of applications pertinent to earlier exploration stages are possible. Product value estimates may or may not be difficult, depending on the pricing structure of the particular commodity. A simplified accounting procedure usually may be adopted without introducing any significant loss of validity. This paper describe some of the financial analysis applications which are pertinent during mineral exploration and deposit development. These applications lend additional insight during exploration planning, land acquisition, physical exploration, and development. The examples are oriented toward a hypothetical management investment policy which is based on a single criterion, a minimum 15% discounted cash flow rate of return. In reality, managements use multiple criteria. This simplification is convenient for purposes of presentation and does not invalidate the examples. Computers are useful, but not a requirement, for the applications described. The use of computers provides the results on a more timely basis at costs lower than equivalent manual computations. UNDERLYING PRINCIPLES AND ANALYSIS METHODS Data estimates are subject to uncertainty. The analyst may choose to assess this uncertainty by using one of two principles. Each principle has some advantages. The principle most commonly employed is "assumed certainty." Each financial analysis is based on one set of selected data, which may represent the average estimates, minimum expected conditions, etc. The critical data is identified by making successive calculations, varying the values used. Such studies, called sensitivity analyses, isolate the economic effect of various uncertainties, and guide the allocation of future efforts toward improving the overall accuracy of the analysis. A second principle, "assumed risk," examines the interactive effect of the current uncertainties by qualitatively assigning probability distributions to each data element. These probability distributions indicate the currently appraised chance that a given numerical value will prove to be true. The corresponding procedure, risk analysis, consists of processing many individual financial analyses, each analysis being based on randomly selected numerical values from the probabilistic distributions. The result is a numerical presentation of the uncertainty, but care must be exercised in the interpretation of results. The advantage of this procedure is the direct measurement of economic uncertainty caused by the interaction of uncertain estimates. Kennecott Copper Corp. has developed computer systems for accomplishing sensitivity and risk analyses.

Jan 1, 1970

By Frank Sames

Most Blasting Programs are developed focussing on the environmental impact with respect to blast vibration and airblast. Compliance with existing regulations or policies limiting the immissions are generally achieved through constrains in the blast design, or monitoring programs. Efficient monitoring programs combine compliance monitoring and blast assessment. Signals, which are obtained in the area of direct influence of the seismic source, can contain valuable information about the blast design parameters. Techniques to analyze blast vibration signals have advanced and can assist in understanding the contribution of individual blast parameters to blast vibration and airblast. Advanced signal analysis encompasses magnitude analysis, Fast Fourier Transforms (FFT) and frequency scans in the frequency domain, as well as filtering in the time domain. Through examples, the advanced signal analysis techniques and their limitations are described and discussed, showing the impact of blast timing, timing accuracy, charge configuration and the geology dependent transmission behavior. Optimization criteria and pragmatic monitoring programs can be developed on the basis of the most influential blast parameters. In addition, however, safety and the cost efficiency of the blasting program are essential to the success of an operation. That is where advanced signal analysis techniques can interface with blast planning, computer assisted modeling and information systems. A valuable process can be developed to ensure compliance with existing regulations and efficient risk management for mining operations, while tracking cost and supporting operational decisions. A conceptual blasting information system is presented.

Jan 1, 2000

By W. E. Lee

Penetration and dissolution mechanisms are reviewed for predominantly single-phase oxide, two phase oxide and oxide-carbon composite refractories by liquid silicate slags. Theoretical models of these processes, as well as static (sessile drop, dipping and crucible) and dynamic (rotating finger and rotary slag) experimental tests, along with their practical limitations are considered. Direct (congruent or homogeneous) attack is controlled by the reaction rate at the slag-refractory interface or the rate of diffusive transport of species to it through the slag leading to active corrosion. Indirect (incongruent or heterogeneous) attack is controlled by diffusive transport through the slag or through a new solid phase, which forms at the original slag-refractory interface. This may lead to passive corrosion. Examples of direct and indirect attack in a range of refractory/slag systems are described highlighting the critical influence of the composition and hence viscosity of the local liquid slag adjacent the solid refractory. Penetration and corrosion can be controlled either through the local slag composition via the refractory or the bulk slag or by microstructural control of the refractory by e.g. internal generation of dense layers or external deposition/generation of passive coatings, so-called in situ refractories.

Jan 1, 2004

By Chetan D. Savani, Mike K. Muchard

The necessity to evaluate undocumented foundation lengths is essential in assessing the useable life, need for scour protection, retrofitting, or full reuse of existing bridge foundations. For this purpose, Parallel Seismic Testing (PST) has the best accuracy and is applicable to the widest range of foundation configurations used in bridge construction of any test method. Although not limited to bridges, PST case studies are presented involving two bridges. To preface the case study discussions, an overview of the PST method is given along with its results and analysis thereof. In one of the cases, we were afforded the rare opportunity to see the existing piles being extracted long after the PST testing program was completed. The resulting Class A prediction reaffirms the accuracy of the method. Versatility of the PST method is also exemplified in the two cases presented, where unique situations from complex foundation systems were overcome by analysis to provide successful results.

By Gary E. McIntosh

This paper will discuss a U.S. Bureau of Mines project designed to assess and predict the impacts which surface coal mining will have on the regional shallow groundwater systems in the Powder River Basin. The primary objective will be met through the accomplishment of the following: (1) The design and establishment of a regional network for monitoring of shallow groundwater systems in the Basin. (2) Monitoring of the direction and rate of flow, water quality, and aquifer characteristics of the shallow groundwater systems. (3) Development of a regional groundwater simulation model with appurtenant subroutines to determine local effects.

Jan 1, 1978

By A. Warczok, T. A. Utigard

"Slags from smelting of copper concentrates contains from 1 to 15% of copper. Copper is present in the form of copper or copper matte inclusions of size from 2 to 1000 micro, and as dissolved cuprous oxide. Removal of the copper requires the slag reduction, primarily reduction of magnetite and co-reduction of cuprous oxide. Thus, the kinetics of the slag reduction play an important role in copper recovery. Instantaneously, at the contact of carbon and a slag the gaseous film is formed. The magnetite and cuprous oxide reduction is going through a gaseous film, separating the slag and carbon of a coke or electrodes. The thickness of a gaseous film grows to a critical value and gas bubbles, containing CO and CO2, are created and rise up in the slag. Results of measurements of kinetic of the slag reduction with graphite showed high value of activation energy, close to the value of activation energy of Boudouard reaction. Strong temperature dependence of the reaction rate points out the thermal instability of the reacting system. It was found that the slowest process in the reduction stages determines the loop of CO and CO2 transfer and magnetite diffusion to the slag/gas film boundary. Strongly endothermic Boudouard reaction seems to cause thermal instability on the reaction surface. So, heat transfer to the reaction surface is very important. Due to low thermal conductivity of a slag the convection dominates in the heat transfer. So, any slag stirring accelerates the rate of reduction and coalescence of metallic copper or copper matte inclusions."

Jan 1, 2015