Search Documents

By C. Cutts, K. Wheatley

The Dragon Lake Zone (uranium prospect) comprises a N160º trending vein that is approximately 110 m long, up to 5 m wide and from 1 to 40 m high. The zone is mostly within altered sandstone of the Fair Point Formation, the basal unit of the Paleoproterozoic Athabasca Group, but it also extends downward (up to 3.5 m) into basement rocks that occupy the northerly trending Maybelle River Shear Zone (MRSZ). This subvertical shear zone separates graphitic paragneiss and weakly deformed granitoid rocks to the east from non-graphitic paragneiss and foliated granitoid rocks to the west. The Dragon Lake Zone cuts across both the MRSZ and N060º-N070º-trending cross-faults that offset the shear zone but not the mineralized vein, which contains values up to 54.5% U over 50 cm core length. Strong chloritization occurs in graphitic paragneiss and sandstone adjacent to mineralization. Silica was depleted from the basement rocks and redeposited at the borders of the 5-15-m-wide alteration zone, as well as within overlying sandstone of the Manitou Falls Formation. There are minimal alteration effects in the overlying Lazenby Lake Formation. Geochemistry shows that the alteration zone in the Fair Point Formation is highly anomalous in metals, most notably in Ni, As, U, Pb, Co, and B. Clay within this zone is illitic and Fe-rich chlorite is also present. Brittle deformation is not as widespread or as well developed in the Fair Point Formation as it is in the overlying Manitou Falls Formation, which is extensively brecciated and contains some anomalous metal values.

Jan 1, 2013

By M. Ksiazek

Keywords: Thermal conductivity, thermal diffusivity, flash method, specific heat capacity, manganese ore Manganese ferro-alloys manufacturing involves a combination of quality raw materials and an energy source to produce high-quality products with low energy consumption. The thermal properties of manganese raw materials such as ores, sinters, and briquettes, are among the many factors that determine the amount of energy needed for processing. Thermal expansion, thermal diffusivity, conductivity, and apparent specific heat capacity of solid samples and compacted powder samples of manganese ores were examined from room temperature to 1000 °C. The effect of porosity (of the materials used) on the thermal properties was also investigated. The laser flash method and a pushrod dilatometer were used.

Jan 1, 2011

By G. Norman Owen, Roger E. Scholl

INTRODUCTION The analysis and design of underground structures to resist vibratory motion due to earthquakes has been of interest to engineers for several decades. The dynamic stability of a powerhouse cavern was considered in the 1960s (Campbell and Dodd, 1967). About the same time, the designers of the San Francisco Bay Area Rapid Transit system developed procedures for analyzing the subaqueous tunnels placed under San Francisco Bay and the tunnels excavated along the land portions of the alignment (Kuesel, 1969). Japanese designers developed fairly sophisticated procedures for analyzing subaqueous tunnels during the late 1960s and early 1970s (Kuribayashi et al., 1974). In the past decade, proposals to site important critical underground facilities in regions with moderate to high seismic activity have increased the interest in earthquake engineering of underground structures. Seismic designs or seismic studies have been conducted for rock caverns for storage of petroleum or location of power plants (Yamahara et al., 1977; Glass, 1976), buried tanks for fuels or rad¬ioactive waste (Fukushima et al., 1977; URS/Blume, 1976), tunnels for disposal of nuclear waste (Yanev and Owen, 1978; Wahi et al., 1980), and urban mass transit tunnels (Monsees and Merrit, 1984). One of the greatest drivers of the interest in seismic analysis and design of underground structures has been the proposals to dispose of high-level nuclear waste in mined repositories some 300 to 600 m (approximately 1,000 to 2,000 ft) below the ground surface. In 1979, the authors, in conjunction with Professor Tor Brekke, presented a paper on an evaluation and design procedure used in a study of a proposed nuclear waste repository (Owen, Scholl, and Brekke, 1979).

Jan 1, 1985

By G A. Blengini, S V. èolar

The minerals industry is faced with choices beginning in the exploration phase and extending over the life cycle of the mine. Firms examine the technical feasibility of alternative actions and typically rank them based on economic performance. Increasingly firms also consider alternativesÆ contribution to sustainable development. There are many visions of what a sustainable future should look like and much debate about what should be sustained. Sustainability is a process, a series of incremental actions, and each alternative course of action has the potential to further progress toward one or more sustainability goal. However, because it is not possible to sustain everything everywhere simultaneously, trade-offs and choices inevitably have to be made.Sustainable decision making before investment (ex ante decisions) should incorporate a broad suite of quantitative and qualitative information. One approach is to utilise an integrated sustainability assessment (ISA) framework that supplements traditional technical and financial tools with other tools such as objectives hierarchies (OH) and life cycle assessments (LCA). OH is a problem framing method that captures stakeholder and decision maker interests, objectives and values. LCA addresses material and energy flows, and environmental impacts. The outputs of these tools can be combined with additional qualitative measures and analysed using multi-criteria decision analysis (MCDA). MCDA models facilitate comparison of different alternatives on the basis of a set of criteria and indicators. Some can incorporate information on risk attitudes and preferences ( multi-attitribute value theory models) and others uncertainty about outcomes (multi-attribute utility models). Studies have been published describing and comparing tools for minerals sector decision analysis. Our paper extends this literature, discussing how a combined OH-LCA-MCDA can support ex ante sustainability assessment by incorporating preferences, risk attitudes, and monetised or non-monetised social and economic variables, in a manner that captures their inherent complexity. We also discuss how such a combined model would support trade-off analysis.

Jan 1, 2009

The profitability of individual ore blocks can be classed as clearly profitable, clearly not profitable, and those in between which are by nature quite sensitive to their major cost and revenue drivers. It is often the case that the most effort goes into the least profitable ore blocks to ensure that these will in fact not generate a loss. In these cases a cut-off grade policy is often not sufficiently live to separate individual sources given the volatility of financial markets and individual circumstances of some sources particularly in remnant operations such as Mount Isa MinesÆ Lead Mine. Standard sensitivity analysis can determine which factors stope profitability is most sensitive to. However, this does not usually indicate the likelihood of any input change, nor the combined effect of multiple inputs changing. The author attempted to modify the Lead Stream financial model that determines cash margin by inserting probability distribution functions and then using Monte Carlo simulations to determine the probability of any particular ore block making a profit. This effectively demonstrates the combined effect of varying a number of inputs simultaneously to provide a probability of making a profit. The limitations of this analysis lie in the accuracy that individual probability distributions can be specified. Attempts to generate valid functions from first principles have proved difficult for a number of reasons and these are discussed along with some practical alternatives.

Jan 1, 2002

Two key elements in the design of a pastefill or high density hackfill system are the preparation of the backfill material and its distribution underground. This paper examines these two areas. Owing to the essentially impervious nature of total mill tailings, preparation of pastefill and high density fill from current tailings involves a physical dewatering process. There are currently three methods available for this process: I. Vacuum or pressure filters. These represent the 'traditional' approach to the preparation of pastefill. 2. Paste production storage mechanism. This is a thickening/storage mechanism developed with the specific objective of producing paste/high density backfills. 3. Fluidization. This system utilises silos fitted with simple dewatering devices and nozzles. Recently developed by CANMET, it provides the simplest and most economical approach. This paper describes and compares the three preparation methods, from a practical and an economic point of view. Once the pastefill/high density fill has been prepared and binder added, the backfill must be distributed underground into the stopes. A fundamental factor in the design of a distribution system is the rheology of the material- No two materials will exhibit the same properties, and a sequence of rheological and related testing is required prior to the completion of the design of the underground distribution system. This paper covers the testwork normally required and discusses the fundamental design parameters of pastefill distribution systems. The final section of this paper summarises the use of pastefill at three mincsin Canada.

Jan 1, 1998

By R. P. D. Graham

It is almost exactly two hundred years since the foundations of the mining and metallurgical industries in Canada were laid. There '."'as nothing spectacular about this early start. It had to do with the most basic phases of these industries-the mining of coal and iron ore, and the manufacture of cast and wrought iron. At several points along the coast of Cape Breton island, coal seams may be seen outcropping quite conspicuously, and it is probable that they had been observed, and possibly worked in a small way, in very early times. However that may be, these coal seams have the distinction of being the first in North America of which there is any printed record, reference to them appearing in a volume by Nicolas Denys which was published in Paris in 1672. Regular coal mining in the district did not commence until about fifty years later, however. The metallurgists started their operations along the north shore of the St. Lawrence river. Here, at many points between Montreal and Quebec, are to be found deposits of bog iron ore, and in 1 730 a furnace for smelting such ore was established on the St. Maurice river. The St. Maurice forges continued in operation until 1880, and throughout that long period they were famed for the fine quality of castings produced, and also for a-superior wrought iron.

Jan 1, 1924

By David Burchell

Duckbill mining is probably the simplest method of loading coal mechanically at the face in underground mines. It is a means of reducing the amount of physical labour required to produce a ton of coal. In effect, it is merely shaker conveyor mining brought up to date with the addition of a self-loading head or 'duckbill' on the end of the conveyor line. Any mechanical device used to load coal is a means of supplanting the human muscles as the medium for getting the coal off the floor into the transportation equipment. There can be no argument with the conclusion that a man can lift so much and no more. He can load more tons of coal on a low conveyor, because the lift is less, than he can in a pit car two, three, or even four feet high. Thus it follows that, if the lifting operation is entirely eliminated, the man should be able to produce even more coal. A mechanical operation is essentially a multiplication of physical strength. Although there are various ways in which coal can be loaded at the face by mechanical means, there is, perhaps, none more adaptable than shakers equipped with duckbills. This is particularly true for thin seams and in mines having heavy, tender top conditions which require close timbering. However, as we are discussing duckbill mining, we will make no further reference to any other type of equipment. The first, and to date the only, mine in eastern Canada to adopt a system of mechanical loading at the face is the Franklin mine of the Bras d'Or Coal Company, Ltd., at Bras d'Or, N.S. An experimental Goodman shaker conveyor with a self-loading head, or duckbill, was installed in this mine in 1940. Since that time other units have been placed in operation so that, today, this mine is completely mechanized. The method of operation 1s room-and-pillar. The operation is carried on in a 42-in. seam, which lies 420 feet beneath the Sydney Main or Harbour seam in the Sydney Mines basin. The slopes bear N.25 30'E., dip 10 per cent seaward, and are about 6,000 feet in length. The physical conditions of this seam do not make it particularly adaptable for complete mechanization as it contains a large amount of foreign material, such as clay intrusions or wash-outs and iron pyrites. These clay intrusions, known locally as 'troubles', vary in thickness from a few inches to as thick as eighteen feet and usually replace the coal to the full height of the seam.

Jan 1, 1947

By A. H. Daane, R. L. Myklebust

The yttrium-manganese system has been investigated by thermal, metallographic, and X-ray diffraction methods. There are three intermetallic compounds present: YMn2 which melts congruently, YMn4, which undergoes syntectic decomposition, and YMn,, which undergoes peritectic decomposition. The compound YMn4 is ferromagnetic at room temperature with a Curie temperature of 214°C. There are eutectics at 25.2, 60.9, and 82.0 wt pct Mn which melt at 878°, 1100°, and 1075°C, respectively. Crys-tallographic data are given for YMn4, and YMn12 . The terminal solid solubilities are low. In a general program of study of yttrium metal in this laboratory some alloy systems of this metal with elements of the first transition period have been examined. This work was originally instigated by experiences in cladding yttrium with jackets of some protective metals such as Inconel for high-temperature service in air.' In some cases a low-melting phase was observed to form between the Inconel and the yttrium resulting in failure of the samples. In characterizing this reaction, a survey was made of the systems of yttrium with chromium, manganese, iron and nickel,, and it was found that a eutectic was formed between these metals and yttrium on the yttrium-rich side of the system. This present study of the Y-Mn system was carried out to examine in more detail the alloying nature of yttrium, and to correlate trends that have been observed in previous related studies. It was observed by Voge13 that in the systems of lanthanum, cerium, and praseodymium with each of the metals in the first transition series, the tendency to form compounds diminished in the order nickel, cobalt, and iron while no compounds were formed with manganese, chromium, or titanium. Beaudry and Daane4 observed a similar behavior in the systems of yttrium with some members of the first transition series except that the tendency for compound formation was greater. Both the Y-Ti5 and Y-Cra systems consist of simple eutectics, while in the Y-Fe,7 Y-CO, and Y-Ni4 systems, there are four, eight, and nine compounds, respectively. In addition to the above trends, the similar atomic radii and electronegativities of yttrium and thorium invite a comparison between their alloying behaviors with a common element such as manganese. In crys- tallographic studies, Florio et al.' have identified three intermediate phases in this system which are ThMn2, Th6Mn23, and ThMn,,. Gschneidner and Waber10 have examined published information on alloy systems of the rare-earth metals and have correlated this information with current alloying theory. From their study, they predicted that the Y-Mn system would contain one intermetallic compound. On the basis of this prediction, the trend in the alloying behavior of yttrium with the elements of the first transition series and the alloying behavior of thorium with manganese, one might expect from one to three intermetallic compounds to form in the Y-Mn system. A consideration of Hume-Rothery's rules of alloying based on size-factor, electronegativity, and valency suggested a small terminal solubility and possible compound formation. The present study was undertaken to confirm these predictions of low terminal solid solubility and compound formation and to establish the general alloying behavior of yttrium with manganese. EXPERIMENTAL Materials. The manganese used in this investigation was obtained from the Foote Mineral Co. as electrolytic plates of 99.9 pct stated purity; the yttrium metal was prepared in this laboratory. Table I gives the analyses of these materials. For the solubility studies at the yttrium-rich end of the alloy system, distilled yttrium, whose major impurity was 200 ppm Ti, was used. Preparation of Alloys. The alloys were formed by comelting the two metals in an are-melting furnace under an atmosphere of argon. The buttons thus formed were inverted and remelted three to five times to promote homogeneity. Due to the high vapor pressure of manganese, it was assumed that the weight lost during are-melting was all manganese. This assumption was based on the very good agreement observed between calculated compositions and chemical analyses of several alloys. The compositions of the dilute alloys used for solid solu-

Jan 1, 1962

By Eric E. Cather

In 1984 and 1986, at the request of the U.S. Forest Service, the U.S. Bureau of Mines conducted a mineral appraisal of the 315,000-acre Lemhi Range study area. This area is located in Lemhi and Custer Counties, about 25 mi south of Salmon, Idaho, and is in the Northern Rocky Mountain physiographic province, Topography is generally rugged with elevations ranging from 5,600 ft to about 11,350 ft above sea level. Since the 1880's, approximately 500 mining claims have been located within the study area; about 400 were current at the time of this investigation. Also, part or all of 12 patented mining claims are in the study area. During Bureau field work, forty-four mineralized sites were examined. The sites had been explored by 80 adits, 14 shafts, and about 140 pits and trenches. At least five properties in the study area have had significant production; the adjacent Mohawk, Grace Phelan, and Snowbird claims had a combined total of 136,000 oz of silver and 67,000 lb of lead; production at the Brown Bull was about 14,800 oz of silver and 115,000 lb of lead; the Portland mine yielded an unrecorded amount of silver. The Hilltop mine, located a few hundred feet outside the study area, produced 125,000 oz of silver, 2.7 million lb of lead, 87,000 lb of zinc, and 62,000 lb of copper from mineralized zones that might extend into the study area. More than 10,000 lb of copper were produced at the Blue Jay mine from workings located about 1,000 ft outside the study area. The Bureau of Mines investigation did not reveal the presence of identified resources in the study area. However, several areas contain mineralized sites and are known occurrences. Some of these warrant additional work to further delineate the mineralization and possibly determine identified resources.

Jan 1, 1988

By Jeffrey S. Walker

The purpose of this U.S. Bureau of Mines effort was to determine if ground movement caused by mining-induced subsidence is directly transferred to a structure and, if so, how that transfer takes place. Four concrete block walls with foundations were constructed and monitored over an active longwall panel. Three of the walls were located perpendicular to the direction of mining in zones where maximum inclination, maximum tension, and maximum curvature were predicted to occur. The fourth wall was constructed along the centerline of the panel, parallel to the direction of mining. All of the walls and the surrounding ground surface were instrumented with conventional survey monitoring points and extensometer stations to observe the vertical and horizontal movements. The fourth wall instrumentation also included continuously recording tiltmeters. The results of this investigation indicate that these simple structures respond to subsidence in a similar manner as the ground surface. This suggests that once the transfer mechanism is more fully defined, prediction models can be developed to accurately estimate the effect of mining on surface structures.

Jan 1, 1989

By L. Garycki, P. Poks, R. Urbaniak, T. Gabka

In 2016 at Głogów Copper Smelter KGHM Polska Miedź S.A., after shutting down the shaft furnaces new FSF was launched. Currently, it is the only smelter with two direct to blister flash smelting furnaces in operation. The main difference between the vessels are the dimensions and production capacity. The new furnace design output is about 30% higher compared to the old flash smelting furnace working for 40 years. The paper presents a comparison of both FSFs operation, differences in technology and the way to optimize the process to maximize efficiency. INTRODUCTION KGHM Polska Miedź S.A. is the only company in Poland (eastern part of Europe) that extracts and processes copper ores. It is located in the south west of Poland and this region is called the "Copper Basin”. KGHM PM S.A. consists of three underground mines: Lubin, Polkowice-Sieroszowice, Rudna, concentrator plants, a tailings pond plant, three copper plants: Legnica, Głogów and Cedynia wire rod plant in Orsk. The publication relates to the operation of the furnaces in Głogów (the plant in Głogów consists of Głogów 1 and Głogów 2 which form integrated smelting and refining facilities). In 2016, after closure of the shaft furnaces technologies in the Głogów 1, a new FSF commenced operation. The simplified process flow sheets are given in Figure 1 and 2. Technological schemes are similar, but due to the differences in them, they will be discussed separately. Głogów 1 Enriched ores are discharged and directed to the feed preparation plant. Delivered concentrates are built up on the three bedding aisles in appropriate proportions. The concentrates are distributed in even layers in one of the three aisles. Aisle emptying is done with a blending machine which cuts across the concentrate layers and collects thus blended material, sending it via belt conveyors to a storage bin. From the cross- blending machine and conveyor assembly, the mixture of concentrates is directed to drying in the steam dryer. Part of the charge is directed to the FSF and part to the roaster for carbon elimination. Known in the world roasters are used to eliminate sulfur compounds or arsenic. In the case of KGHM deposits, the aim of the process is to reduce the energy value of the feed by eliminating carbon and converting sulfur from sulfide to sulfate. Changing the nature of exothermic to endothermic material is crucial in the case of furnace operation with design performance. Roaster is a separate furnace with an innovative character.

Jan 1, 2019

By Lewis Robert M.

The importance of phosphate in feeding the people of the world has been recognized by mining companies as they continue their search for new ore deposits and ways of improving phosphate production. An extensive phosphate-recovery research project involving investigation of beneficiation variables by batch testing, flotation pilot-plant processing of the major portion of the ore, gravity separation of the coarse fraction, and recovery of byproduct heavy minerals of a North Carolina phosphate deposit has been completed. Data obtained through batch tests enabled the development of an economical flowsheet which proved successful for the efficient recovery of a good quality phosphate concentrate in a pilot plant.

Jan 1, 1975

By Charles Hardy

ACTIVATED alumina is an aluminous material which may be 1 classified chemically as a partially dehydrated aluminum trihydrate having a high porosity and a perma¬nent physical structure. In general, it may be employed effectively and economically for the complete removal of water vapor from gases and vapors; for the selective adsorption of certain as especially those of the higher boiling points, and as a catalyst or catalyst carrier. Other forms of alumna are available and may be employed similarly but not so effectively nor can reactivation be accomplished with uniformity over many cycles without deterioration. The adsorption-reactivation cycle of activated alumina can be repeated many times without any apparent depreciation ill

Jan 1, 1934

By Michael Rieber

Commodity transportation by barge is possible on about 25,000 miles of navigable inland waterways in the contiguous 48 states. Barge operations are used chiefly for the movement of bulk raw materials ranging from farm products to iron ore, coal, and other bulky semi-finished as well as finished products such as steel, chemicals and petroleum [3,p.7-9]. The barge industry, unlike other transportation industries, is largely unregulated. This is because all liquid bulk commodities most dry bulk commodities transported by for-hire carriers and companies engaged in private transportation of their own commodities are exempted from Interstate Commerce Commission regulations. As a result, about 15 percent of the total ton-miles of barge traffic each year is under Interstate Commerce Commission regulation [13,p.14-25].

Jan 1, 1977

The purpose of this paper is to describe briefly the clean-up procedure adopted at the treatment plant of Paringa Mining & Exploration Co. Ltd. at Kalgoorlie, Western Australia.A clean-up is carried out at the end of each four-weekly period, and all figures subsequently quoted are taken from a summary of the results of the eight periods ending 8th April, 1941.STRAKING AND AMALGAMATIONOf the total gold won 22· 77 per cent. is recovered by straking and amalgamation.The discharges of both the primary and secondary ball mills are pumped over a common set of five ten feet long by three feet wide straking tables, set at an angle of 10 degrees, before passing to the 14 ft. diameter by 30 ft. by 8 ft. Dorr bowl classifier.This classifier is in closed circuit with both of the ball mills, hence the whole of the circulating load of the fine grinding circuit, which approximates to 800 per cent., is required to pass over the straking tables. For convenience in handling, corduroy cloths are used in lengths of 5 feet, and are picked up and replaced by clean cloths at four-hourly intervals. The avaHable straking area provided is, therefore, 900 square feet, or approximately 3·30 square feet per original ton per 24 hours. The density of the pulp passing over the tables is about 54 per cent. solids, the area provided per ton of pulp per 24 hours being approximately o· 2() square feet. Washing of the corduroy cloths is carried out on the day shift only, about 800 lb. of strake concentrate being obtained daily.This concentrate is sluiced from the washing trough on the elevated straking floor to the 4 ft. by 2 ft. diameter amalgamating barrel located in the gold room below.The barrel is of standard design and is rotated at 25 r.p.m. It is charged each day at 4 p.m., and grinding of the strake concentrate at approximately 70 per cent. solids is continued until 8 a.m. the following day. The barrel is then stopped, and the contents generously diluted with water, and after a few minutes rotation some of the slime is carefully poured off through the small discharge hole. This dilution and decantation is repeated until a good deal of the valueless slime has been removed.A further quantity of strake concentrate is then charged to the barrel, which is allowed a further 16 hours grinding period. After again diluting and decanting, approximately 25 lb. of mercury and 15 lb. of lime are added to the charge, which is then given an amalgamation period of 2 hours before cleaning up.By the process of grinding, diluting and removal of slime by decanting...

Jan 1, 1941

By G D. Price

Scheelite mineralisation east of the main divide in' the Southern Alps of New Zealand was originally identified by Royden Thompson who is now a geologist with the NZ Geological Survey. This mineralisation was brought to the attention of CRA in 1978. Reconnaissance surveys were carried out in 1979 to delineate the extent of the mineralisation. This was undertaken using ultraviolet light examination of the sediments within the major drainages in the Southern Alps. This defined tentative zones of prospective mineralisation. As a result of this, preliminary reconnaissance, exploration licences were applied for -those areas in which indications of scheelite mineralisation were strongest. A total of 1737 km2 of ground was applied for within four exploration licences. These covered the main Southern Alps mountain chain between the Haast/Wanaka highway and the Mt Cook National Park.

Jan 1, 1983

By Rosiane Mary Rezende Faleiro

A Vallourec tem investido na tecnologia de carbonização contínua com objetivo de produzir carvão vegetal, CV, de boa qualidade siderúrgica e maior rendimento na conversão madeira / CV siderúrgico, tornando o processo viável em termos técnicos e econômicos para o cenário brasileiro. O objetivo desse trabalho foi comparar, por simulação termoquímica, o impacto relativo nos consumos de CV granulado enfornado pelo topo, utilizando CV produzido por fornos retangulares de alvenaria e CV obtido no reator de carbonização contínua da Vallourec, o Carboval. A qualidade siderúrgica superior do CV Carboval permitiu reduzir o consumo específico de CV granulado em 18,2kg/t que, somando ao melhor rendimento gravimétrico e menor geração de frações finas, torna atrativa e viável esta tecnologia. Estas vantagens impulsionam o setor a sair do artesanal para o industrial na produção de CV.

Aug 17, 2017

By H. D. BAILEY, John W. Cole

This paper is one of a series on mining methods and costs published by the Bureau of Mines .. Because of the role, played by the Federal Government in the discovery of the ore body, a description of the exploratory operations of the Bureau of Mines, is included ...

Apr 1, 1948

This report summarizes the work performed under USBM Contract No. H0395041. The primary objective of this work was to extend the noise control technology developed under earlier USBM projects to a wider range of load-haul-dump models to evaluate the general applicability of these techniques. Noise control treatments were designed, fabricated, and installed on three Wagner LHDs (an 5T-2B, ST-2D, and an 5T-8A) selected as demonstration machines for this project. The machines were evaluated either in production mines or at the Bureau's Lake Lynn Mine. The results indicate that it is possible to achieve overall noise reductions of between 4 and 8 dB using these techniques. Engine cooling and seal design were determined to be important design issues in such treatments.

Jan 1, 1984