Search Documents

By Wolfgang G. Brunner

The center of Berlin is currently a huge jobsite, where international architects, designers, consultants, construction and ground engineers as well as investors take on the challenge of the biggest and probably most complicated projects in terms of soil conditions in Europe. The Berlin sand is generally suitable for foundation measures, but can be very tricky in deep excavation pits below the high ground water level. The reason for this is its uniform grading, medium dense stratification and lack of cohesion. The requirements for these deep pits are: - measurements in the range of up to 120 000 m2 per pit - depths up to 19 m below ground water level - lack of dense horizontal geological layers - no permission for lowering ground water levels - toughest ever European competition in construction. Sheet pile walls, sheet piles set into cut - off walls, secant pile walls, diaphragm walls, all with tie backs under high water pressure, are used as retaining sytems. The pits are closed at the bottom against water either by under water concrete, deep lying grouted cut - offs or high lying jet - grouted cut - off slabs. The huge dimensions of these excavation pits are a new challenge for ground engineers, and new technology had to solve the upcoming problems and resulted in new experience.

Jan 1, 1999

By Z Li, A Fleming, S Webster, L Snyman

Northparkes Mines is developing the E26 Lift 1 North block cave mine, which is adjoined to the existing E26 cave. This paper presents the challenges and methods used to design the ground support system during the feasibility study. Calibrated numerical simulations were conducted to forecast the levels of rock mass damage and to assist the ground support design. Generally, low to moderate rock mass damage is forecast on the extraction and undercut levels. However, poor ground conditions are expected in sheared and preconditioned zones adjacent the existing E26 cave. This will result in difficult ground conditions during development, undercutting and drawbell establishment. Empirical assessments were conducted to make sure the ground support system is able to handle both the static and dynamic load demand, and to accommodate the deformation values. A safety factor of 1.5 was used for the designs to cover the unknown rock mass conditions and potential for larger seismic events. Learnings from the E26 Lift 1 and SLC, also mining against the E26 cave, are incorporated into the design. Fibrecrete, mesh and resin bolts / mechanical anchors are the primary ground support system used, and cable bolts for intersections with a span of more than 6 m. Following undercutting and during the operating life of the mine, secondary ground support and rehabilitation will be required.

Mar 15, 2021

By A. H. Lang

Introduction The recent uranium discovery at Theano point, lake Superior, is probably a rediscovery of the first reported Canadian uranium occurrence. A description of material from the original discovery was published in 1847 by J. L. LeConte, and many attempts have been made to relocate the deposit. Such attempts have in the past been unsuccessful because of vagueness in the original description of the locality. Besides being a prospect that seems to merit development work, the Camray discovery is important because it reaffirms the occurrence of pitchblende in the eastern part of the Precambrian shield. Much staking followed the announcement of the discovery, and some additional finds have been reported. Location The Camray discovery is at the shore of Theano point, lake Superior, about seventy miles north of Sault Ste. Marie (see Figure 1). It is in township 29, range XIV, district of Algoma. The showing is two miles from Highway No. 17, and is reached by a rough trail that leaves the highway at mileage 72.9 from Sault Ste. Marie. There are no towns of any size nearer than Sault Ste. Marie.

Jan 1, 1949

By Sanjiv Dhanjal

"Often mineralogy dictates the physical properties of a material rather than chemistry. This in turn affects how that material behaves in a process plant, and whether optimum conditions for refining one mineral are different to those for refining another. For example how does refining copper from chalcopyrite differ to refining copper from bornite?Minerals are naturally occurring inorganic solids that have a definite chemical composition and an ordered atomic (crystalline) structure. X-ray diffraction is a common and highly developed method to identify and quantify minerals. X-rays are fired onto a material and the mineral is identified by the angles where the diffracted X-rays are in phase.Most X-ray analyzers are laboratory based. A sample is prepared and analyzed by a detector that travels in an arc to collect the diffraction pattern. COSMA has a curved detector which picks up the complete x-ray pattern instantaneously. Therefore, material is collected and transported through the machine where is it is analyzed continuously.COSMA measures about 0.5 tons of material per day, while laboratory analyzers measure a few grams at a time. Real time data trends are produced allowing for improved process evaluation and automatic control. The COSMA on-line system has taken X-ray diffraction out of the laboratory into the field.There are a number of systems in operation in cement production. It is recognized that on-line mineral analysis has a role in many other processes. This paper presents the technology and invites further discussion should the technology be beneficial to members of the audience.INTRODUCTIONThis article describes COSMA, a system that provides direct and continuous on-line mineral analysis using X-ray diffraction in the field. While X-ray diffraction is a common technique used in mineral analysis, the time from sampling to analysis can be hours and plant operators typically do not get the data in time to control a process or respond to an upset. COSMA provides rapid measurement, analysis and feedback of data, in real time. This provides powerful information that can be used to optimize operation, thereby reducing costs and increasing quality."

Jan 1, 2009

By C. Y. Sun

China is a country with abundant resources of tungsten, taking one of the world?s top-positions regarding both the total reserve and the amount of industrial production. China?s tungsten resources occur mostly in multi-metallic deposits rather than in single-metallic deposits. China?s multi-metallic tungsten ores have the characteristics of coexistence with other valuable components such as molybdenum, bismuth, copper, sulfur and fluorite. These ores are usually low in grade and difficult to process. The technological challenge in mineral processing lies in separation of multi-metallic components in these complex ores and a comprehensive utilization of natural resource. Several cases of industrial practice of processing China?s typical multi-metallic tungsten ores are presented.

Jan 1, 2014

By D. D. Macdonald, G. Engelhardt

The accumulation of damage due to localized corrosion [pitting, stress corrosion cracking (SCC), corrosion fatigue (CF), crevice corrosion (CC), and erosion-corrosion (EC)] in complex industrial systems, such as power plants, refineries, desalination systems, etc., poses a threat to continued safe and economic operation, primarily because of the sudden, catastrophic nature of the resulting failures. Of particular interest in managing these forms of damage is the development of robust algorithms that can be used to predict the integrated damage as a function of time and as a function of the operating conditions of the system. Because complex systems of the same design rapidly become unique, due to differences in operating histories, and because failures are rare events, there is generally insufficient data on any given system to derive reliable empirical models that capture the impact of all (or even some) of the important independent variables. Accordingly, empirical models have generally failed to provide a robust basis for predicting the accumulation of corrosion damage in complex systems under realistic operating conditions. The alternative prediction philosophy is determinism, in which the development of damage is described in terms of valid, physico-electrochemical mechanisms with the output being constrained by the natural laws. The differential damage is then integrated along the corrosion evolutionary path for the system (i.e., over the future operating "history") to yield the desired integrated damage, which is the quantity that is most useful to an operator. In this paper, we review the theory of predicting corrosion damage within the framework of Damage Function Analysis (DFA), with particular emphasis on the pitting of aluminum in chloride solutions and on the accumulation of damage from SCC in Type 304 SS components in the primary coolant circuits of Boiling Water (Nuclear) Reactors (BWRs). These cases have been selected to illustrate the various phases through which localized corrosion damage occurs.

Jan 1, 2005

By Jian Wang, Xiaoming Sun, Ming Jiang, Fuxin Shen, Chengyu Miao, Wenchao Zhao, Yong Zhang

The increased thickness of the coal seam leads to higher goaf roof collapse height. In contrast, the dynamic pressure from the mining of ultra-thick coal seams generates higher abutment pressures around the mined area and may affect the stability of roadways servicing these panels. To mitigate the deformation and damage issues in the roadways during the extraction of ultra-thick coal seams under a high depth of cover, researchers have proposed combining high prestress constant resistance support and roof-cutting technology (HPCR-RC). The deformation and failure mechanisms of the roadways during the extraction of ultra-thick coal seams under a high depth of cover, along with the mechanisms and field control effects of the combined support system, have been analyzed through theoretical analysis, numerical simulation, and field experiments. The research findings reveal that the high in situ stress, initial excavation disturbance, rotation, and subsidence of the fractured roof of the extra-thick coal seam led to significant deformation and damage in the roadways. High prestress constant resistance support compensates for the initial stress loss, reduces initial stress concentration, and absorbs deformation energy. Moreover, the roof-cutting technology severs the connection between the goaf roof and the roadway roof, disrupts the path of stress transfer, raises the level of roof backfilling in the goaf, and provides support to the roof, effectively alleviating the pressure on the coal pillar ahead and adjacent to the working face. Field experiments have confirmed the effectiveness of HPCR-RC, as indicated by a substantial decrease in surrounding rock deformation and support pressure within the roadways.

Sep 25, 2023

By D. Lawrence, H. Lawrence, G. Saevil

Plant operators in the mineral processing industry have been implementing expert systems for several years now, with the intent to increase production and reduce costs. Most systems have been installed on grinding circuits of some type and have proven that the technology is viable in that application. However, few applications on other processes have been attempted for various reasons, such as lack of reference sites, complexity of the process, lack of suitable measurements and lack of confidence in the technology. The successful application of an expert system on an Alumina Calcining kiln is the first such application in the West Indies Alumina Company (Windalco), and demonstrates how this technology can be successfully applied to other processes. The key objective of an expert system is to optimize the process. To achieve this the process must first be stabilized, followed by optimization of the operating parameters. The steps taken by this expert system to optimize the process are: • Check for abnormal conditions and deal with them using a prioritized set of special actions. • Use a selection of rule blocks to stabilize the process. • Once the process is stable, achieve additional benefits through further optimization of the process. The potential benefits that a user can expect to achieve through installing an expert system can be assessed on the basis that performance will improve from that of an "average operator" to that of the "best operator" performing at his optimum for 24 hours a day, every day. The quantifiable process benefits include: • Increased production • More consistent product quality • Reduced operating costs • Reduced standard deviation of key variables • Consistent plant operation The success of this project was measured in several ways: project implementation, realised economic benefits, and realised non-economic benefits. With a commitment to maintain the system over the long term, the longevity of the system is assured and will become an important part of the Alumina Calcining control strategy at Windalco. This paper discusses the various phases of implementing the ABB Expert Optimizer expert system, what the benefits were and the procedure that is in place to maintain the system to ensure continued long term success.

Jan 1, 2002

By F. N. Kissell

The machine-mounted continuous respirable dust monitor (MMCRDM) is a fixed-location area sampling device developed for possible use at the working face of an underground coal mine. This device, based on proprietary technology known as the tapered element oscillating microbalance, has evolved over the past eight years through a cooperative effort of the former Bureau of Mines, MSHA, and the Rupprecht & Patashnick Company in Albany, NY. The capability to measure respirable coal mine dust levels on a continuous basis, rather than depending solely on periodic samples obtained from the traditional coal mine dust samplers, has been a goal in the mining industry for nearly two decades. Recently, an extensive series of laboratory and underground tests was conducted by NIOSH with the cooperation of MSHA and coal operators to test the performance of the MMCRDM In preliminary laboratory testing, the MMCRDM seemed to work well. However, in every underground test, when compared to reference samplers placed close to the inlet, the MMCRDM failed to meet the 25% accuracy criterion specified in the contract under which it was developed. Two reasons explain this failure: First, in most tests the bias (the relative discrepancy between the average MMCRDM concentration and the average reference sampler concentration) was too great. Second, the variability of the samplers used for reference comparison was too large. Finally, the underground testing of the MMCRDMs showed that they are quite unreliable at this stage of development. In the majority of mine tests, no more than 10 shifts of data were taken before the MMCRDM failed to function properly. Major breakdowns, requiring the return of the MMCRDM to the factory for repairs, occurred on average every 28 days. To be considered mine-worthy, MMCRDM reliability must be substantially improved. KEYWORDS Dust, coal dust, dust instrumentation, dust sampling, dust monitoring, black lung, pneumoconiosis

By Sean Gallagher

Bolting large sheets of wire mesh screen (WMS) to the roof of underground mines prevents injuries due to rock falls. However, WMS can be heavy and awkward to lift and transport, and may result in significant spinal loading. Accordingly, six male subjects (mean age =45.8 years + 7.5 SD) were recruited to lift WMS in a laboratory investigation of the biomechanical demands. Biomechanical modeling was used to estimate external moments about L5-S1 for sixteen lifting tasks, using two sizes of WMS. Full-size WMS involved a two-person lift, while half-size WMS involved a one-person lift. Lifts were performed under 168 cm and 213 cm vertical space. Restriction in vertical space increased the maximum L5-S1 extensor moment from 254 to 274 Nm and right lateral bending moment from 195 to 251 Nm. Lifting full sheets of screen (as opposed to half sheets) resulted in an average 33 Nm increase in L5-S1 extensor moment. The L5-S1 extensor moment was increased by an average of 44 Nm (18%) when lifting screens positioned flat on the floor compared to an upright position. Relevance to industry: Large flexible materials are commonly lifted in industrial work environments, and may involve the efforts of two or more workers. The current study examines the low back loading associated with lifting large flexible screens and presents recommendations to reduce spine loading.

Jan 1, 2009

By W. L. Saunders

(New Haven Meeting, February, 1909.) This paper deals specifically with heading-driving as distinguished from the broader term tunnel-driving. A heading is a pilot or path-finder for the main tunnel. Some headings are complete tunnels in themselves; that is, conditions at times warrant driving a heading the full diameter of the proposed tunnel. A tunnel 10 ft. in diameter might be driven to advantage through a single heading, provided the nature of the material admits, but it usually pays to drive rock tunnels of large diameter through the heading-and-bench system. Much de-pends upon the material, as in soft ground tunnels of much larger diameter are driven in a single heading. In mines, the tunnels, drifts, cross-cuts, adits, etc., are usually of small diameter, hence the driving of headings applies to completed tunnels in minim-work, except, of course, in cases like drainage-tunnels and main entries leading into coal-mines, where conditions call for tunnels of large diameter, approximating those driven for railway-service. In building aqueducts the tunnels are driven from 6 to 8 ft. in diameter up to 15 or 20 ft., while in railway-service the dimensions vary from 18 to 30 ft. in diameter. There is no department of rock-excavation so difficult as that of heading-driving. This work. also belongs to the most expensive class in rock-excavation. A heading is driven .directly in the solid. There are no lines of lesser resistance towards which to direct the energy of the blast, but. the material must be blown out by main force. The completion of the heading simplifies all the rest of the work of excavation. It is easy, for instance, to enlarge a heading either from above, below or oil the sides, by breaking towards the open face through holes approximately at right angles to the axis of the heading; or the enlargement sometimes takes place by holes driven outside

Apr 1, 1909

By Roberto Bria

El presente texto describe el módulo prefabricado para las salidas de emergencia. En este sentido, el sistema modular prefabricado busca facilitar y agilizar la instalación de salidas de emergencia desde el interior de mina hasta superficie mediante RB entubados con módulos armados fuera de la Unidad Minera, mejorando la seguridad mediante un sistema confiable de fácil colocación, reutilizable, y de gran robustez. De ese modo cumplir con el objetivo primordial de las salidas de emergencia de 200 m hasta la superficie, en terrenos de calidad de roca regular a mala.

Sep 21, 2013

This report describes the results of a program to design, procure, install, and evaluate a multi-channel underground telephone system of modern design in the Sunshine Silver Mine near Wallace, Idaho. Although the evaluation portion of the program was deleted, this report contains a cost benefit analysis for such a system using estimates of operational data for the Sunshine Mine. The results show a centrally switched telephone system of conventional design with ruggedized phone enclosures and special environmentally sealed dial pads to be the most economical.

Jan 1, 1982

By Jerome Apt

This manual has been prepared fur the help and guidance of underground coal mine operators. It details both common and unique engineering methods by which the respirable dust, which is generated in coal mines, can be controlled. This document was compiled by Apt, Bramer, Conrad and Associates, Inc. under contract number H0111464, issued by the U. S. Bureau of Mines and forms Volume II of the final report. This contract was authorized by and executed pursuant to the Federal Coal Mine Health and Safety. Act of 1969 (P. I. 91-173; 83 Stat. 742).

Jan 1, 1972

By D. Rahal

All ores have an economic optimum particle size (Wills and Napier-Munn, 2006). This optimum value is often a compromise between the need to achieve adequate liberation for the efficient separation and recovery of valuable minerals and the energy consumed by the crushing and grinding process. It has been recognized for nearly three decades that grinding is the most expensive and least efficient stage in mineral processing (El-shall and Somasundaran, 1984). At that time it was estimated that grinding consumed between 25 and 70% of the total power required in mineral processing. This recognition drove the development of new stirred mill fine grinding technology in the 1990s (Jankovic et.al, 2003; Enderle et. al., 1997; Massey, 2008). These milling technologies have a reduced energy consumption compared to traditional fine grinding using ball mills. In the ?coarser? fine grinding applications this improvement is approximately 30%. The benefits increase to above 50% in ultrafine grinding applications (Lichter and Davey, 2006). Despite these gains, the US Department of Energy reported that an additional energy savings of up to 37% is possible in the minerals industry. They identified continuing research and development and implementing best practices in both grinding and materials handling as the primary avenues for the additional reduction (BCS, 2007).

Jan 1, 2011

By Alton B. Cook

The practice of using partly depleted oil reservoirs for gas-storage operations is proving successful. Moreover, this practice provides a method of secondary oil recovery when gas is cycled at full-storage reservoir pressure. Because of the relative newness of this operation, a study was undertaken to assist engineers in developing improved gas-injection and production procedures and in calculating the amount of gas needed for completely repressuring reservoirs. This paper is the third in a series reporting the progress of a study by the Federal Bureau of Mines of reservoir performance during complete gas repressuring and gas cycling. A procedure for estimating secondary oil recovery by this method is also under study. One report (7)3/ describes the laboratory equipment. The other report (8) gives (1) data on the New York City field, Clay County, Tex., which has been converted to gas-storage operations; (2) laboratory data from research with a model oil reservoir, in which primary production, complete gas repressuring, and gas cycling for the New York City field were simulated; and (3) theory to explain reservoir performance during gas repressuring.

Jan 1, 1961

By Kwangmin Kim, Junnhyeok Park, Taehee Lee, Minkyu Kim

Mine tailings storage facilities (TSFs) can be a significant source of fine, respirable dust. This dust poses concerns, especially for nearby communities, because of its detrimental impact on respiratory health. To address these concerns, this study examined the effectiveness of commercially available polymers, known for their biocompatible and environmentally friendly features, to prevent dust generation from upstream-type TSFs in active mining operations. It focused on two areas in TSFs: the tailings beach and slope/dike surfaces. Two types of polymers—polyethylene glycol and poloxamer—were selected, and their effectiveness was evaluated in a series of phased laboratory and field tests. The lab tests investigated the moisture-retention capacity of the tailings after treatment with the polymer solutions as well as the ability of these solutions to reduce dust emissions. Polymers were applied to a tailings bed surface in the lab and dust was generated from this surface using a wind tunnel. PM10 and PM2.5 concentrations were measured using laser-diffraction dust sensors, and the polymers were found to have reduced dust emissions up to 95%. Small-scale wind-blowing tests were conducted in the field (specifically, in a controlled environment at a TSF) to evaluate polymer effectiveness on the tailings beach and slope/dike areas. The tests revealed that the AP could efficiently suppress approximately 80% of PM10 and PM2.5 dust emissions at both types of areas. Finally, 1000 gallons of AP solution were discharged at the top of tailings beach and slope/dike areas, respectively, and found to be effective. The results of these tests showed the high potential of the biocompatible polymers to be a feasible solution for reducing the respirable dust emissions from upstream TSFs in arid and semi-arid regions.

By T. T. Chen

Copper anodes generated from copper scrap are relatively rich in Sn, Zn and Fe. Because of the presence of oxygen, only trace amounts of Sn occur in solid solution in the copper crystals. Thus, Sn occurs mainly as SnO2, Cu-Sn-Ni oxide and Sn-Ni-Zn oxide in the copper anodes, and Zn and Fe occur mainly as minor constituents in the Sn-Ni-Zn oxide and Cu-Sn-Ni oxide. During electrorefining, these oxide species are liberated from the copper anodes and report directly to the anode slimes. The trace amounts of Sn present in solid solution in the copper crystals dissolve but reprecipitate as Sn arsenate or a Sb-As-Sn-O phase. Accordingly, high Sn contents in copper anodes do not lead to elevated Sn concentrations in the electrolyte.

Jan 1, 2010

By T. B. Counselman

"C" VERYONE who has to calculate cyanide circuits, -¦-' using either thickeners, filters or both, realizes the headaches involved in solving a set of simultaneous equations. When you calculate a large number of these, based on experimental data, trying to arrive at the best flowsheet, you can spend days at the task. T. B. COUNSELMAN, Member AIME, is Manager, FluoSolids Division, The Dorr CO., Stamford, Conn. AIME New York Meeting, Feb. 1950. TP 2783 B. Discussion (2 copies) may be sent to Transactions AIME before March 31, 1950. Manuscript received Aug. 23, 1949. Herewith is presented a short method, equally accurate with the standard simultaneous equation method, and much quicker. Here for instance is the standard simultaneous equation method, for 100 tons per day of $10 ore, with the conditions assumed as below (fig. 1). Conditions Assumed a. 100 tons of ore per day crushed in cyanide solution. b. Discharge from all thickeners with 50 pct moisture. c. $10 value dissolved per ton of ore. d. 50 pct in mill and 50 pct in agitators. e. 400 tons of solution from thickener V precipitated to $0.02. f. Agitation with a dilution of 2 of solution to 1 of solids. g. Let V, W, X, Y and Z represent value in dollars per ton of solution discharged from the resvective thickeners. Equating Out of and Into Each Thickener 1. lOOVplus 400V = 500W plus (0.50 X $10 X 100) 2. 1OOWplus 600W= 500X plus lOOW plus (0.50 X $10 X 100) plus lOOV 3. lOOXplus 500X = 1OOWplus 500Y 4. 1OOY plus 500Y = 1002 plus 1OOX plus (400 X 0.02) 5. 100 Zplus l00Z = l00Y plus 100 tons of water (value $0.00) Simplifying: 1. v = W plus 1.00 2. W = X plus 1.20 3. X = Y plus 0.24 4. Y = 0.2Zvlus 0.064 5. 2Z= Y

Jan 1, 1951

By T. B. Counselman

"C" VERYONE who has to calculate cyanide circuits, -¦-' using either thickeners, filters or both, realizes the headaches involved in solving a set of simultaneous equations. When you calculate a large number of these, based on experimental data, trying to arrive at the best flowsheet, you can spend days at the task. T. B. COUNSELMAN, Member AIME, is Manager, FluoSolids Division, The Dorr CO., Stamford, Conn. AIME New York Meeting, Feb. 1950. TP 2783 B. Discussion (2 copies) may be sent to Transactions AIME before March 31, 1950. Manuscript received Aug. 23, 1949. Herewith is presented a short method, equally accurate with the standard simultaneous equation method, and much quicker. Here for instance is the standard simultaneous equation method, for 100 tons per day of $10 ore, with the conditions assumed as below (fig. 1). Conditions Assumed a. 100 tons of ore per day crushed in cyanide solution. b. Discharge from all thickeners with 50 pct moisture. c. $10 value dissolved per ton of ore. d. 50 pct in mill and 50 pct in agitators. e. 400 tons of solution from thickener V precipitated to $0.02. f. Agitation with a dilution of 2 of solution to 1 of solids. g. Let V, W, X, Y and Z represent value in dollars per ton of solution discharged from the resvective thickeners. Equating Out of and Into Each Thickener 1. lOOVplus 400V = 500W plus (0.50 X $10 X 100) 2. 1OOWplus 600W= 500X plus lOOW plus (0.50 X $10 X 100) plus lOOV 3. lOOXplus 500X = 1OOWplus 500Y 4. 1OOY plus 500Y = 1002 plus 1OOX plus (400 X 0.02) 5. 100 Zplus l00Z = l00Y plus 100 tons of water (value $0.00) Simplifying: 1. v = W plus 1.00 2. W = X plus 1.20 3. X = Y plus 0.24 4. Y = 0.2Zvlus 0.064 5. 2Z= Y

Jan 1, 1951