Search Documents

By K. Izumi

Ultra-grain refinement and high strengthening of metals by accumulative roll bonding (ARB) was widely reported. However, applications of ARB to magnesium alloys were rather limited. In this study, Mg-9%Li-1%Y sheets were applied to ARB at room temperature. Six 0.5 mm thick sheets were stacked and reduced into 0.5 mm thick by four passes. The procedure was repeated up to three cycles, so that the equivalent strain of 6.2 was applied. The sheets show dual phase structure with a (hcp) and ß (bcc). Grains elongates to the rolling direction with increasing number of ARB cycles. After three cycles, fragmented a grains with average size of about 300 nm are uniformly distributed. After the first cycle, the ultimate tensile strength increases to 180 MPa from 133 MPa, while the elongation decreases, however, still high (26%). The tensile strength slightly decreases by the second cycle and does not change at the third cycle. Meanwhile the elongation increases by the second cycle and the sheets show 41% of the elongation after the third cycle.

Jan 1, 2006

By Leon Nelson

SEVERAL factors which affect the segregation and solidification of killed hot-topped steel ingots are: (1) pouring temperature, (2) volume in the hot top, (3) taper in the ingot, (4) pouring rate by varying the nozzle size, (5) segregation of several elements, (6) moving ingots before completely solidified. In most of this discussion, segregation will be measured in terms of carbon variation only. All the data given are results on S.A.E. 1040 analysis of fully killed steel direct-poured in hot-topped molds giving 20-in. square ingots. Thus the variables of analysis and ingot size and contour are eliminated. Segregation results are all on the rolled-bloom size, not on the ingot itself. They are results from plant-control work and not results of special research on ingot segregation.

Jan 1, 1937

By W. W. Graff

This paper describing the mining practices at Mine, No. 4 on the Marquette range, Michigan, is one of a series of articles on mining methods and practices in various mining districts in the United States. Mire No. 4 is located in the Swanzy district, in the southern end of the Marquette range, about 3 miles from Gwinn, Mich. The Swanzy district is an isolated ore-bearing formation, and Mine No. 4 is at the extreme southeastern end.

Jan 1, 1930

By C. C. Jobes

Operating large face equipment, such as continuous mining machines, is one of the most basic and most dangerous elements of an underground coal mining operation. The operator usually performs cutting and tramming tasks in a restricted workspace with reduced visibility. During the execution of these tasks, operators often cannot see all of the locations needed to safely operate the continuous mining machine (CM ), which has sometimes resulted in accidents. In an effort to prevent these accidents, researchers at the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory, examined the continuous mining machine operator?s current information cues, or visual attention locations, so that risk of injury relative to the task, equipment and workplace environment can be evaluated in the future. The eventual goal is to develop interventions to enhance the information cues, and thereby increase the safety and health of machine operators. This paper details the operator interview process, determination of visual attention locations (VALs) and simulation of various mining scenarios.

Jan 1, 2011

By John Corcoran

INTRODUCTION Content of this Report The 1300m long twin-bore 8.1m diameter Airside Road Tunnels (ART) were excavated beneath the busy taxiways and stands of Heathrow Airport between 2002and 2003. The tunnels were fully completed and handed over to the client for use early in 2005. This paper will describe the purpose of the tunnels, and the measures put in place to minimize the impact of construction on the daily activities involved in running an international airport. Terminal 5 Construction Heathrow Airport is the busiest international airport in the World, with a current capacity of circa 67 million passengers per year, based on existing infrastructure of4 passenger terminals, 1 cargo terminal, 2 runways and 170 aircraft stands. Terminal 5(T5) is being built to increase Heathrow’s passenger capacity by providing the following: 12 additional aircraft stands through redevelopment of the south apron area, in the autumn of 2004 A main terminal building (T5A) and a first satellite (T5B), and 43 additional stands by the spring of 2008, most of which will be able to receive the new generation large aircraft (Airbus A380) A second optional satellite (T5C) by year 2010 A third optional satellite (T5D) by year 2015 The total value of the project is approximately 4.2 billion pounds for the main phase of the works spanning from 2000 to 2007. Purpose of the Airside Road Tunnel The ART has been constructed to support the internal road traffic of the airport between terminals, aircraft stands, runways and taxiways, for passenger buses, service and technical vehicles. The majority of the traffic will be buses transporting passengers between the terminals and their aircraft.

Jan 1, 2005

By A R. Penney

Since mining-induced seismicity first became apparent at the Beaconsfield Gold Mine in 2002, there has been an ongoing program of geotechnical investigations to understand the phenomenon and allow for the development of strategies to manage the risks it posed to personnel, the business and the community at large. Studies resulting from a seismically induced rockfall on Anzac Day 2006 have been extensive, and have advanced the understanding and management of seismicity at the mine. Enhancement of the mineÆs seismic array, implementation of extensive monitoring of ground behaviour, improved ground support and reinforcement design, and ongoing numerical modelling provide a technical framework for the management of seismicity. In addition, extensive involvement of the workforce in risk assessment and the development of standard work procedures (SWPs), has contributed to a æbest practiceÆ approach to manage seismic hazards at the mine.

Jan 1, 2008

By John C. Nichols

The Ouachita, Ozark-St. Francis, and Mark Twain National Forests are located within the Ozark and the Ouachita Mountains regions of southern Missouri, central and northern Arkansas, and eastern Oklahoma- an area generally referred to as the Ozark-Ouachita or Interior Highlands. These national forests share many similarities in geography, biotic resources, and areas of shared public, market, and user interests. The three national forests have joined together to evaluate the natural resources within the Highlands and to study the impacts of the forests on local and regional economies and on the people who use these national forests and their resources. Other federal, state, and local government agencies and universities have joined with the Forest Service in this project, broadening the assessment area beyond the national forest boundaries to include 107 counties in Arkansas, Missouri, and Oklahoma. The diverse, resource-related data for the as- sessment area address social, economic, terrestrial, and aquatic issues and conditions throughout the Highlands. The assessment report currently is being developed by the Forest Service and will include an accoMpanying CD-ROM. The Ozark-Ouachita Highlands assessment has provided a forum for minerals- and geology-related resources, industries, social significance, and potential to be profiled and discussed along with other critical assessment resources. The state geological agencies in Arkansas, Missouri, and Oklahoma were active contributors to this effort. Their reports and other key data bases developed and used for the minerals sections of the published assessment report will be available either as a supplemental CD-ROM or on the Internet. Updated information on the progress of the assessment report can be found at the Ouachita National Forest Website, at <http://www.fs.fed.us/oonf/ouachita.htm>. This will also include a matrix displaying the minerals in the assessment area, their occurrence by assessment-area counties, and a potential ranking, as well as information on interesting geologic features. The state and federal reports, resources, and data bases, have helped answer key questions concerning mineral resources and related issues in the Highlands:

Jan 1, 1999

By M. A. Islam, H. Mischo, G. Barakos

Among the thirty-five declared critical raw materials (CRM) in the United States, there is no sustainable domestic production for the fourteen of them, while for some others domestic supply does not meet the national demand. Numerous potential critical raw material projects are in advanced exploration stages. However, the price uncertainties for many of these commodities put feasible future production into question and come into contrast with overly optimistic price forecasts published in all feasibility studies related to such exploration projects. Thus, in this work, a newly developed smart computational tool is used to evaluate the real perspectives of several CRM exploration projects implementing actual commodity prices, and to conduct reverse calculations in order to find the prices at which each project can be viable.

Mar 2, 2022

By Olav K1omstad1ien

The lean, but extensive iron ore deposits of the Dunderland Valley north of Mo i Rana, Norway, is the raw material for the Rana Mines which is a division of the state owned steel mill A/S Norsk Jernverk. Activities for the exploitation of the orebodies were commenced in 1902 by the English Dunderland Iron Ore Company. During its operating period the company constructed a total of two large scale concentrating plants. The activities were strongly marked by technical problems and labor disputes. Thus actual production was limited to the years 1904-1908, 1928-1931 and 1937-1939. During these periods a total of 1.9 million tons of crude ore was mined and 0.6 million tons of concentrates produced for export. The present plant commenced operations in late fall of 1964. Up to and including 1976 about 26.6 million tons of crude have been put through the concentrating plant and about 10.7 million tons of concentrate produced.

Jan 1, 1978

By W. L. Zhong

Probability function integration method is one of the influence function method. It is a widely accepted method in many mining districts in China and Poland mainly because its theory and formulae can well-represent the surface subsidence basins due to longwall mining of flat or near-flat seams. This paper introduces the basic theory of the probability function integration method and determines its 4 basic parameters by analyzing the measured subsidence profiles in eight longwall panels in Northern Appalachian Coal field. It also discusses the two methods for determining the 4 parameters. Finally the acquired parameters are used to predict the subsidence and deformation of the houses for damage assessment. Comparisons are made between the measured and the predicted subsidence. Probability Function Integration Method The probability function integration method for predicting surface movements and deformations is widely used in China and Poland. The governing equation of the method contains five parameters: subsidence factor, a, offset of inflection point, d, tangent of the major influence angle, tan fl, horizontal movement constant, b, and major dispersion angle e (e = 90. for flat seams). Its applicable range iis much larger including seams less than 30&apos; from the horizontal, critical and noncritical mining and soft to hard overburden.

Jan 1, 1986

By Sergio Cattalanl, Francis Chartrand

"The geology and origins of volcanogenic massive sulfide (VMS) deposits in the Abitibi belt of northwestern Quebec have been the subject of discussion since the discovery of the Horne orebodies in Noranda in 1923.The present Noranda version of the VMS model characterizes the ideal deposit as a stratabound, base-metal accumulation that is in close spatial relationship with hydrothermal alteration and stockwork zones, felsic lava domes, coarse phreatic-pyroclastic breccias, and subvolcanic intrusions that characterize vent- and proximal{acies submarine volcanic environments. Deposits tend to occur in a favorable stratigraphic interval within a mining camp, and this is well-documented in the Rouyn-Noranda and Matagami camps.However, in recent years many VMS deposits have been shown to deviate from the ideal Noranda-type. For example, the Ansi/ deposit is characterized by sulphide-bearing alteration zones that extend far above the massive sulfide lenses, and by abundant magnetite immediately underlying massive sulfide. The Horne deposit appears to lack the typical chloritic alteration pipe underlying the massive sulfide lenses, as well as laterally-equivalent exhalite horizons. The Horne and Quemont deposits, besides being the two giants of the camp, are particularly rich in gold, whereas others, such as WaiteAmulet and Millenbach, have low gold values. Finally, some deposits in the Noranda camp, such as the Ansil, Corbet and Mobrun mines, are outside the favorable stratigraphic interval. Therefore, it would appear that part of the key to renewing base metal reserves in northwestern Quebec is the use of evolving descriptive-genetic models that incorporate geological variations like those cited above."

Jan 1, 1990

By R. A. Cattell

With the surrender of the Japanese Imperial Government as a climax to the capitulation of the German High Command , the main objective of the Petroleum and Natural Gas Division pivoted from war assignments to its main normal functions . One of these functions is to give wide public distribution to valuable technical facts which the Division has obtained through research on petroleum , natural gas , helium , and related subjects . During the war years many engineering data and scientific facts could be released only on a restricted basis as reports to war agencies and others immediately concerned . Moreover , many of the wartime reports contained masses of detailed data that were prepared under stress to meet emergency schedules . For peacetime publication and application , these data must be reviewed , correlated , and rearranged so as to present the essentials in proper form . To illustrate , a wartime report of 50 pages might be resolved into one curve in a composite graph for a peacetime publication . Another factor affecting the orientation of the work of the Division is the broader horizon of research revealed by its war activities . Fundamental research and careful engineering analyses are just as important in time of peace as in time of war; in fact , they should be more important to the forward view , because under peace conditions disrupting influences that distract from the orderly acquisition of knowledge are minimized . Therefore , the concerted effort has been not to " salvage " the results of the war activities , but to evaluate them on the basis of their relative importance in the future economy of the country . Where wartime investigations have pointed to peacetime accomplishments , the effort has been to give the corresponding type of work additional emphasis . This adjustment can not be made hurriedly , but many of the necessary preliminary steps on the new course have been taken ..

Jun 1, 1949

By David Flores, Benjamin Cebrian

Gold mining require high levels of dilution control due the high value of ore. These types of operations employ short benches, which are suitable for ore control, lower displacement and more representative block models. However, shorter benches makes fragmentation by blasting difficult because blast designs tend to be stiff in regards to burden/bench height ratio. This is especially relevant in hard, massive ore bodies where usual drilling diameters lead to poor energy distribution. In regards to control ore loss and dilution, there are different techniques to minimize both, which include: panel blasting, buffer blasting to muck piles and differential loading of areas of the blast bench. All of them should be sequenced with appropriate displacement along the ore/waste contacts. This paper describes extensive engineering approaches to achieve both dilution control while not hurting fragmentation in the very hard, massive ore sections of a mine case study. Ore Tracker microchips are used to correlate performance of these designs at the SAG mill (bottleneck of this specific operation). Another gold mine uses the same technology to detect when and where operational dilution is happening. The system tells where flagging of the different ore bodies has been followed in order to detect which operators pass the excavation limits beyond ore control flagging.

By Robert W. Ageton

The Bureau of Mines investigated the in situ vertical component of the rock stress in the rib of the haulage drift on the 6100-level of the Star mine, Burke, Idaho, using the flatjack and borehole deformation methods. The estimate of the vertical component of stress about 2 feet into the rib at a station along the haulage drift on the 6100-level of the Star mine by the flatjack method is approximately 5,875 psi, whereas the borehole deformation procedure at this station yielded a value of 5,500 psi for the same depth into the rib. The test zone is approximately 5,625 feet below the surface.No attempt was made to extrapolate stress estimates beyond the depth of the flatjack installation.

Jan 1, 1967

By Yuchen Wu, Purushotham Thkkaraja, Marek Borowski, Jie Liu, Jianwei Cheng, WANCHENG ZHENG, Yu Wang, Weidong Lu, Gang Zhao, Zhanyou Sa, Huan Yang, Yuhang Wu, Hui Wang

The abstract discusses the importance of gas drainage in coal mines for safety, environmental protection, and resource utilization. It highlights the significance of borehole sealing technology for efficient gas drainage. The study introduces a new inorganic retarding sealing material and investigates its properties, including stability, thermal stability, fluidity, and thixotropy. The material's diffusion performance in cracks is tested using a self-designed system. Field tests in a coal mine demonstrate the material's effectiveness in improving borehole sealing compared to traditional materials.

May 1, 2022

By Antonio Raschillà

On the 2nd of June 2007 SELI S.p.A. started the excavation of Beles Tailrace Tunnel (Ethiopia). The new 8,07 m diameter DS Universal TBM utilized for the tunnel excavation was manufactured by SELI S.p.A. and allowed the installation of 30 cm thick concrete lining, contemporaneously with the excavation of 7,200 m of tunnel. The greatest part of the tunnel alignment was excavated in hard and sound basal-tic rocks. The paper describes the main steps of the tunnelling operations which led to a remarkably rapid excavation, with a peak production of 36 m / day and a final break-through achieved 46 days ahead of the contractual deadline. Furthermore the paper describes the work and logistic organization that was set up to efficiently perform the mechanized excavation in the very remote area of the project.

By C. Lorimer Colburn

"The diverting of men from industry to combat in the world's war focused the attention of the operators in this country upon mechanical means of doing things. The demand for man-power -was so insistent that every available agency for multiplying it had to be employed. It was during the 1period of the war and immediately thereafter that development of the use of underground loading devices made most rapi4 progress. In all parts of the United States, mining engineers and mine managers were diligent in their efforts to develop mechanical loaders. The mining engineers of the U. S. Bureau of Mines in every section of the country have secured, with the cooperation of the mine operators, data on the actual performance of the mechanical shovels in their districts, and have made them available to the author of this paper.No effort has been made to discuss exhaustively the subject of underground loading devices. It has been the object to collect together in one paper, records of the performance of all machines now in actual use. Improvements in the design of machines are constantly being made the performance records given in this paper relate to operation prior to March 1 1 1921. The records prior to 1920 cay not fully represent the work that could be accomplished with the present models of the same machine.The data secured are given exactly as reported by the mine operators. Since this data were collected there have been two underground loaders, of a different design, put into operation in the iron mines of the Lake Superior District. One is the John Mayne Sub-level loader, being tried by the Cleveland-Cliffs Iron Co., Ishpeming, Mich., and the other is the Cole-Goudie shovel, being tried by the Oliver Mining Company, at Ironwood, Mich. No information has been secured regarding the performance of either of these machines."

Oct 1, 1921

The Aredor mine employs conventional dragline methods to exploit alluvial diamond deposits. Production began in 1984 with the policy of mining in the terrraces during the wet season and in the river flats during the dry season. Early production failed to meet predicted grades. A major geological programme to re-evaluate existing reserves was undertaken. This resulted in considerable increases in reserves in the river flats. Many of the reserve blocks included flats on both banks of the Baoule river. Methods of access into the river flats, normally flooded in the wet season, were developed to allow mining throughout the year. River diversions have been the main method used to provide access into the reserve blocks and, most importantly, to remove the risk of flooding. Aredor has carried out six main river diversions with a total length of 12 km. The diversions allowed production planning to be made on the basis of the economic evaluation of the reserve blocks, without undue regard to natural ground conditions or to seasonal factors. The Manning equation was used for the calculation of channel dimensions and gave satisfactory results. The practical aspects of the diversion preparations and flooding prevention are described

Sep 1, 1991

By Alfred R. Powell

LATE in 1944 a group of petroleum and coal technologists was organized in Wash¬ington under the sponsorship of the Petroleum Administration for War and the U. S. Bureau of Mines. This group, known as the Technical Oil Mission, was placed under the authority of the Technical Industrial Intelligence Committee of the Joint Chiefs of Staff, which was then promoting the organization of other missions to be sent to Germany to obtain technical information regarding various industries in that country. The objective of the Technical Oil Mission was to obtain technical data on German production of synthetic oil from coal and all other commercial practices and research projects connected with the oil industry. The primary purpose was to obtain such data as were immediately essential to assist the war against Germany and Japan, with secondary emphasis on technical information that would assist American industry after the end of the war. Since oil-production facilities in Ger¬many and the occupied countries con¬trolled by Germany were the top targets for strategic bombing, the Technical Oil Mission was the first group under the Technical Industrial Intelligence Com¬mittee to enter Germany. A few members of the group flew to London in February 1945 and the majority of the remainder followed in March. In London they were joined by an equal number of British investigators and the combined, mission was then sent into Germany under the authority of the Combined Intelligence Objectives Subcommittee (CIOS). A sum¬mary of the more important information gained by this combined British and American mission is presented below. GERMAN OIL PRODUCTION The oil available to Germany, both natural and synthetic, and including pro¬duction from occupied countries, reached a peak in late 1943 and early 1944. Pro¬duction at this time was at the rate of 1,200,000 metric tons per month, equiva¬lent to i00,000,000 bbl. per year, or about 7 per cent of the wartime production in the United States. Of this production, 50 per cent was crude oil from Romania and Hungary, 12 per cent was crude oil from Germany itself, including Austria, 9 per cent com¬prised coal-carbonization products, that is, tar and light oil, and only the remaining 29 per cent was synthetic liquid fuel made from coal or tar. Synthetic liquid fuel made in Germany was equivalent therefore to less than 2 per cent of war¬time production of crude oil in the United States. The success of the strategic bombing campaign against German oil-production facilities is demonstrated by the fact that by September 1944 the Ploesti fields of Romania and much of the syn¬thetic oil production had been eliminated, so that the amount of oil available to the German war machine was only 25 per cent of the peak quantity mentioned above. By early 1945, when the combined British and American oil mission was entering

Jan 1, 1946

By E. D. Gardner

This paper is a progress report on the study of mining methods and costs in the western United States and summarizes that part of the work pertaining to the undercut block-caving method of mining. Ore is mined on a large scale exclusively by the undercut block-caving method at the following six mines in the western United States: The Morenci branch of the Phelps Dodge Corporation, Morenci, Ariz.; the Ray mines of the Nevada Consolidated Copper Co. at Ray, Ariz.; the Inspiration Consolidated Copper Co. at Inspiration, Ariz.; the Miamo Copper Co. at Miami, Ariz.; the Ruth mine of the Nevada Consolidated Copper Co. at Ruth, Nev.; and the Consolidated Coppermines Corporation at Kimberly, Nev. The undercut block-caving method is also used at the mine of the Andes Copper Mining Co. at Potrerillos, Chile.

Jan 1, 1930