Search Documents

The Fraser Range is composed dominantly of basic pyroxene granulites derived from basalts, many of which appear to have been vesicular and pillowed. Acidic and basic garnet-bearing granulites are important in the west, and acidic granulites and narrow anorthosite layers are dominant in some regions east of the Fraser Range. An extensive flat-lying olivine gabbro sheet cuts the granulites, and in places has been converted to spineI-bearingmeta-gabbros and pyroxene granulites. The granulites of the Fraser Range (Proterozoic) are separated from the gneisses and schists of the goldfields regions (Archaean) by the Fraser Fault, over which there is a large gravity anomaly (gradient 20 milligals per mile). Some of the problems associated with the concentration of Cu, and Ni liberated from mineral lattices during metamorphism, and other principles of metal concentration in granulite terranes, are discussed. The recognition of vesicular and pillowed zones, even though highly metamorphosed, is of fundamental importance.

Jan 1, 1969

The Greymouth Coal field is situated on the West Coast of New Zealand's South Island and has been mined for coal for more than 120 years. The area covered in this paper is within the Rapahoe Sector of this field and contains >200 million tonnes of low ash, low sulphur, bituminous rank coal. Paper No 6, presented to the 19th Annual Conference of the New Zealand Branch of The Australasian Institute of Mining and Metallurgy in Christchurch in August 1985 by R G Bowman, explained 'A Geologist's View' of the 'Economic Potential of the Greymouth Coalfield', and describes previous geological assessments of the Rapahoe Sector.

Jan 1, 1989

By M. E. Rossi, J. E. Camacho

"Geostatistical conditional simulations are becoming increasingly popular as tools that provide models of uncertainty at different stages of a mining project. They have been used as grade control tools in daily operations to assess the uncertainty of mineable reserves at the project’s feasibility stage, and to assess mineralization potential in certain settings. Other applications include assessment of recoverable reserves, resource and reserve classification, and drill hole spacing optimization studies. All large-scale applications of conditional simulations intend to benefit from the correct (or accurate) characterization of uncertainty, adequately describing the variability observed from the data and its effect on the final objective.The objective of this paper is to compare the ad-hoc uncertainty model provided by a traditional classification scheme with the probability intervals resulting from a conditional simulation model. It is argued that the uncertainty model derived from the use of classification schemes is of little practical use to the mining company or operation. The paper emphasizes differences in uncertainty based on the size of the mining unit considered, the extraction method, and local geological differences. Most importantly, it discusses confidence intervals for these mining units, as compared to the relative precision envisioned by a typical classification scheme.The application described in this paper is taken from a medium-sized Cu open pit and underground mine in northern Chile, and demonstrates the impact of several variables on the resulting conditional simulation models. It also compares a more traditional resource classification scheme applied, and the wide difference in local confidence intervals for each mining unit."

Jan 1, 2004

By D. J. Englund, R. A. Davis

"A three-dimensional CFD model of a straight grate furnace for indurating iron-oxide pellets was developed for exploring conditions of furnace operation for fluid flow, heat transfer and reactions. The model includes reactions for natural gas combustion in the gas phase and calcination and magnetite oxidation as well as drying in the pellet bed. The performance of the model was investigated with a series of pellet production rates that included adjustments to the fuel rates to achieve proper induration temperatures in the pellet bed. The model may be used to discover opportunities for process improvement.IntroductionIron oxide pellets are a feedstock to blast furnaces for iron making. Pellets require physical strength characteristics needed to maintain their integrity during storage, handling, transportation and smelting. Pellets are produced from iron ore in a series of mineral processing operations that form wet green balls from slurries of iron-ore concentrate with binders, such as bentonite, and possibly fluxing-agents such as limestone and dolomite. The green balls are dried, fired at high temperature, and then cooled in an induration furnace to achieve the strength and chemical composition required for efficient reduction and slag separation in blast furnaces. Induration furnaces are generally straight grates or grate-kilncooler configurations. These furnaces operate with pellet beds passing through a series of temperature zones to control drying and chemical reactions in the bed.Process air passes through the zones in an overall counter flow direction to the pellets for efficient heat transfer and energy recovery from the cooling stage. Consequently, the zone conditions and the overall furnace performance are highly coupled. Thus, it becomes challenging to predict how changes to any single zone may affect the rest of the furnace. To gain a better understanding of machine performance and coupling, a three-dimensional, steady-state model of a complete straight grate induration furnace was created using computational fluid dynamics (CFD)."

Jan 1, 2015

Societal influences, needs, and uses for recyclable materials are becoming increasingly important business and economic factors in the traditional natural resource companies. Several metals (such as steel, aluminium, zinc, lead and cadmium) are amenable ro recycle which eliminates solid waste generation and decreases the depletion of natural resources. In recent years, the non-ferrous industries have begun to recycle more materials and the next decade will see even larger recycle efforts. In addition to the traditonal recyclable materials, existing metallurgical plants are, or should be, able to handle and recycle materials viewed as 'hazardous'. Unfortunately, some national and regional regulations hinder, and in some cases prevent, the recycling of certain materials. Zinc Corporation of America (ZCA) is currently the largest producer of zinc metal in the USA and one of the world's largest producers of value-added zinc products. Over the last few years, ZCA has become one of the world's largest recyclers of zinc from various diverse materials. ZCA considers these recyclable materials as valuable 'land mines' that provide economic alternatives to the depletion of natural resources while serving society in the minimisation of solid waste disposal. Using the current production facilities of ZCA as a model, this paper overviews the recycling of zinc-bearing materials with special emphasis on: 1. the amenability for recycle within ZCA's pyrometallurgical and hydrometallurgical operations, 2. the quantities and economics of recycle, 3. the problems of recycling hindered by current national and regional regulations, 4. the concepts of total recycle rather than just recovering zinc while generating a modified solid waste, and 5. the motivators for recycling.

Jan 1, 1993

By W. W. Stephens

As part of the Bureau of Mines program directed toward more effective utilization of the mineral resources of the United States, a number of processes for production of sponge iron have been investigated. The use of sponge iron as a raw material for production of steels and other ferrous alloys offers several possible advantages over the conventional pig-iron and scrap process, especially for utilization of the smeller, widely distributed iron-ore deposits of the western United States. Although considerable information has been made available on various processes for production of sponge iron, little information 118.6 been published heretofore on the problems and costs involved in melting the sponge iron for production of steel. The present Paper reports the results of tests conducted at the Bureau of Nines pilot plant at Redding, Calif. in which several different types of sponge iron Were used as charge material for production of steel in a 4-ton-capacity basic arc furnace.

Jan 1, 1949

By C. A. Stewart

I. INTRODUCTION AND GENERAL STATEMENT OF RESULTS. The field-work upon which this paper is based was done in the summer of 1910, and was made possible by the courtesy of the Imperial Copper Co., which gave me access to its property. For their kindness in this respect I wish to express my thanks to W. F. Staunton and Meade Goodloe. Moreover,. B. F. Smith and G. B. Gentry, mining engineers in the employ of the company, gave invaluable assistance by placing maps,. etc., at my disposal, and by discussing with me the problems of the district; and it is a great pleasure to acknowledge this indebtedness to them. In order that the significance of some of the details that follow may be better appreciated at first reading, a general outline of the conclusions reached is given here. In the Silverbell mining-district a series of Palaeozoic limestone blocks is completely surrounded by post-Palaeozoic igneous rocks, intruded in the following order: alaskite, alaskite-porphyry, biotite-granite, andesite, and quartz-porphyry. The biotite-granite is believed to represent a differentiation of the. magma from which the alaskite-porphyry came ; and this conclusion-has an important hearing on the origin of the ores. The intrusion of both alaskite-porphyry and biotite-granite was followed by the emission of magmatic waters, which sericitized and silicified the alaskite-porphyry and granite, and produced in the limestone, by the addition to it of silica, iron, and alumina, great masses of garnet, quartz, and wollastonite. Following close upon these solutions came metal-bearing magmatic waters, which impregnated porphyry, granite, and alas kite with cupriferous pyrite, and deposited in the garnet zones chalcopyrite and copper-bearing pyrite that make important bodies of contact-metamorphic ores. Secondary enrichment has taken place in the disseminated ores in the igneous rocks,. raising their copper-content to 2 per cent. in some cases,. and extensive drilling has been undertaken to block out these deposits. East of the contact-metamorphic deposits there is a fissure-vein of lead-silver ore in the quartz-porphyry. This rock is distinctly younger than the alaskite-porphyry and the granite; and the lead-silver ores belong, therefore, to a period of mineralization distinctly later than the copper-deposition.

May 1, 1912

By Howard C. Pettibone

Mine safety personnel reported occurrences of excessive "glove-fingering" and other problems with resin-grouted roof bolt installa tions. To study these problems, the Bureau of Mines designed a test plan to (1) obtain baseline information on several resin cartridges and (2) investigate the variables involved in the installation of a resin bolt. Three brands of resin representative of the industry in January 1983 were selected for cartridge evaluation. The installation variables selected for study were the method of installation, the hole depth, and the hole annulus. These variables were studied by installing a series of bolts in concrete blocks using different values for each variable. Results of the research show overspinning the resin may cause problems, but they can be avoided by using the spin times recommended by manufac-turers. Excessive glove-fingering is not a problem if the manufacturer-recommended installation procedures are followed.

Jan 1, 1987

By Donald R. Johnson

Apparatus providing simultaneous differential thermal analysis, thermo-gravimetry, and evolved gas analysis, has been developed by the Bureau of Mines specifically for thermal study of oil shale and other solid, natural fuels. The apparatus is described in detail, and simultaneous analyses on a single sample of an oil shale mineral, nahcolite, and a thermal analysis demonstration compound, calcium oxalate monohydrate, are presented to demonstrate the instrument's capabilities.

Jan 1, 1970

By Terry L. Muldoon

The report describes the development of preliminary requirement specifications for standardized operating controls for roof bolting machines used in underground coal mining. According to recent statistics, roof bolting continues to be one of the most hazardous occupations in underground coal mining. The two principal hazards to the roof bolter operator are the machine itself and roof falls during the bolting cycle. The lack of standardization of machine controls is a major contributor to this hazardous situation. Observations of roof bolting operations and discussions with roof bolter manufacturers coupled with detailed analyses of roof bolter control design specifications were performed during this study. Detailed roof bolter operator task analyses, commonality of control analyses, and classical link analyses were also performed. The results of these analyses were then used to produce preliminary requirement specifications for standardized controls.

Jan 1, 1980

By K-H. Frohne

This report presents a study of the Cooper sand of the Fork Run pool of Warren and McKean Counties, Pa., and a prediction of the secondary oil recovery by gasflooding the reservoir. A computer program employing a modification of the Craig, Geffen, and Morse secondary recovery calculation was used to make the gas flood performance forecast and is presented in the appendix. The Cooper sand reservoir in the Fork Run pool lies at a depth of about 1,900 feet and covers an area 1/2 mile wide by 2-1/4 miles long. Original oil in place is estimated to have been 8,266,000 STB. The primary recovery mechanism is solution gas drive, and ultimate primary recovery may reach 20 percent over a well life of 90 years. Two computer predictions were made for gas flooding the Cooper reservoir. The first was for a 25-acre pilot five-spot utilizing existing wells, but project economics were poor since only 25 percent of injection gas is utilized for pilot oil recovery. Recovery was 71,000 STB, or 22 percent of oil in place at flood initiation, but required 25,700 scf gas injected per STB of oil recovered. In the second prediction, pilot area performance was projected for the entire Fork Run pool, and economics became good. Recovery was 1,753,000 STB from 25 five-spots after the injection of only 6,400 scf per STB of oil recovered.

Jan 1, 1969

By F. H. Gunnell, W. C. Dunham

"INTRODUCTION The Treasure Hill mines, situated in Dry Canyon, Ophir mining district, Tooele County, Utah, together with several other properties in the district, examined were examined by Frank L. Wideman, an engineer, the Bureau of Mines, in September 1942.In April 1945, development drilling was started on the Treasure Hill mines, which are operated under lease from the Madison Mines Co. The project was continued in 1946 and terminated in 1947.While the Bureau of Mines project was in progress, the Morgan and Fullion tunnel workings were surveyed by Bureau engineers.ACKNOWKEDGEMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy, It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual investigative perk, and prepares the final report. The Branch, O. C. Ralston, chief, analyzes samples and performs beneficiation tests. The work here described was under the direct supervision of Paul T. Allsman, chief, Salt Lake City Division, Mining Branch."

Jan 1, 1948

By Wm .. O. Vanderburg

This paper describing the mining practices at the Block P mine of the St. Joseph Lead Co. at Hughesville , Mont . , is one of a series of similar papers being prepared by the Bureau of Mines on mining practices , methods , and costs in the various mines of the United States .

Mar 1, 1931

By Scott Rosenthal, Kyle Murphy

This paper discusses the trials and tribulations of obtaining Velocity of Detonation (VOD) readings in small diameter blast holes in an underground mine. Montana Technological University (Montana Tech) obtained a time-domain reflectometer (TDR) type VOD monitoring unit. Purchase of the VOD monitor was justified on verifying explosives performance used in Montana Tech’s practical underground mining class and provide a teaching aid for the school’s rock fragmentation class. Before demonstrating the unit to students, we figured we better learn how to use it first so we give the students an appropriate experience. Our first learning was in obtaining the correct coaxial cable for the VOD monitor and how to properly terminate the cable. Once the cable was on-site and terminated, VOD testing could commence. Use of the VOD monitor was tested underground in small diameter holes (1.5-inch, 38 millimeter) pneumatically loaded with ANFO. After a few failed trials, and follow-up discussions with the supplier, VOD readings were obtained for the ANFO loaded holes. Additional readings were obtained for a pre-split product and detonating cord to satisfy our curiosity that the unit was performing as specified by the manufacturer. This paper will share our learnings in the hopes that others can benefit.

By W. R. Ingalls

DUPING the last two years, and especially during the last six months, a number of important articles upon the new methods for the desulphurization of galena have been published in the technical periodicals, particularly in the Engineering and Mining Journal and in Metallurgie. I proposed for these methods the type-name of "lime-roasting" of galena as a convenient metallurgical classification,' and this term has found some acceptance. The articles referred to have shown the great practical importance of these new processes, and the general recognition of their metallurgical and commercial value which has already been accorded to them. It is my present purpose to review broadly the changes developed by them in the metallurgy of lead, in which connection it is necessary to refer briefly to the previous state of the art. The elimination of the sulphur-content of galena has been always the most troublesome part of the smelting-process, being both costly in the operation and wasteful of silver and lead. Previous to the introduction of the Huntington-Heberlein process at Pertusola, Italy, it was effected by a variety of methods. In the treatment of non-argentiferous galena concentrate, the smelting was done by the roast-reduction method (roasting in reverberatory furnace and smelting in blast-furnace); the roast-reaction method, applied in reverberatory furnaces; and the roast-reaction method, applied in Scotch hearths 2 Precipitation-smelting, simple, had practically gone out of use, although its reactions enter into the modern blast-furnace practice, as do also those of the roast-reaction method.

Sep 1, 1906

By M. Z. A. Bakar

To investigate the differences in the radial drag pick cutting performance in dry and saturated sandstone, a suite of linear rock cutting test was performed using linear rock cutting machine (LRCM). Experimental results of 50 data passes, incorporating 350 data cuts were used to compute cutting, normal and side forces required for determination of other performance related parameters. Although the forces required to cut the dry and saturated rock were in congruence for most of the spacing and depths of cut combinations; but the overall averaged cutting and normal forces for saturated rock cutting were found to be 9.9% and 9.4% respectively higher than the dry rock cutting. The increase in the overall averaged forces was attributed to strength variability of one of the saturated block affecting the overall forces. The side forces experienced a negligible drop in saturated rock cutting. An increase of 28% and 9% in the actual and nominal specific energy values respectively was also recorded when cutting saturated rock as compared to the dry rock cutting. The increase in saturated rock specific energy is attributed to production of large amount of fines and few large sized chips directly contributing towards increase in specific energy. The optimum s/d ratio for dry rock tests was found to lie between 6 and 8 whereas for saturated rock cuts this value lied between 5 and 9.

Jan 1, 2012

By C. Guo

The Mildred Lake Settling Basin (MLSB) is the largest disposal site for mature fine tailings (MFT) at the Syncrude Canada Ltd oil sands plant. Over the past years (since 1997), there has been a marked change in the consolidation behaviour of MFT in the MLSB, which is attributed to microbial activity. Methane-producing microorganisms, known as methanogens, have become very active, and large amounts of biogas (mainly methane) have been produced. In certain regions within the MLSB, gas bubbles are released to the water surface of the tailings pond. Continued field monitoring of the MLSB has provided convincing evidence of the rapid densification process (rapid water drainage from the tailings). This phenomenon contradicts the consolidation models for MFT developed over the past 20 years. The above phenomenon has also been reported at the oil sands tailings ponds operated by Suncor Energy Ltd. in Fort McMurray. This rapid densification has caused pumping challenges in the transfer of fine tailings from the Mildred Lake Settling Basin for the creation of composite tailings. The rapid densification of the MFT may also have potential positive effects in accelerating the reclamation of the oil sands fine tailings. A field and laboratory research program is underway to study the mechanism leading to the rapid densification phenomenon. Systematic field investigations were performed to determine the distribution and characteristics of the rapidly densified MFT. Gas bubble distribution on the water surface was mapped to determine the zones of different biological activities in the pond. These field investigations provided solid ground for further experimental and theoretical research. A number of small-scale column tests were carried out to observe the gas evolution and to measure the changes of some geotechnical parameters under different microbial activity. Also, a series of gassy MFT densification tests are being conducted to study the mechanism of the rapid densification of the MFT under microbiological activity. A review and discussion of the research program is given and some preliminary research results are presented in the paper.

Apr 1, 2005

Book review Pearson, J. S. Ocean floor mining. Park Ridge (New Jersey), Noyes Data Corporation, 1975. 201 pp. NIM reports Report no. 308 A mineralogical study of gold particles in pulp residues from the Bracken Gold Mine. (7th Mar.,1968. Re-issued Oct. 1975.) Report no. 377 Examination of pulp samples, treated with cyanide, for coated gold.(7th Aug., 1968. Reissued Oct.1975.) Report no. 385 The determination of the nature of coatings on gold particles. (2nd Aug., 1968. Reissued Oct. 1975.) Report no. 452 The Purlex Process - a description of the pilot plant leading to the use of the process in South Africa. (13th Jan., 1969. Re-issued Oct. 1975.) Report no. 482 Review of work on the treatment of pegmatites. (9th Apr., 1969. Reissued Sep. 1975.) Report no. 1443 Gravity concentration tests on four samples from Tantalite Valley,S. W.A. (5th Jul., 1972. Re-issued Sep. 1975.) Report no. 1489 The breakage of S oderberg electrodes. (10th Nov., 1972. Re-issued Nov. 1975.) Report no. 1545 A mineralogical investigation of leach residues from the Blyvooruitzicht Gold Mine. (22nd May, 1973. Re-issued Nov. 1975.) Report no. 1583 Preliminary tests on winnowing for the recovery of mica. (12th Nov., 1973. Re-issued Sep. 1975.) Report no. 1652 The identification of diamonds from Premier, Finsch, and Jagersfontein Mines by statistical analysis of data obtained from instrumental neutron-activation analysis. Report no. 1723 The determination of zirconium and aluminium in zirconiumaluminium alloys. Report no. 1739 The determination of trace amounts of noble metals in sulphate media. Report no. 1771 The determination of silver, selenium, tellurium, antimony, tin, lead, and arsenic in anode sludges. Report no. 1772 A study of copper recovery by lime roasting and leaching. Corrigendum The Special Issue of Volume 76 of the Journal ('Recent Advances in Mineral Dressing, October 1975) should be corrected as follows. The South African Institute Of Mining And Metallurgy - Information On Membershlp The Institute was founded in 1894 as the Chemical and Metallurgical Society of South Africa. In 1904 it was reconstituted as the Chemical, Metallurgical and Mining Society of South Africa and in 1956 it became the South African Institute of Mining and Metallurgy. Die Suid-Afrikaanse Instituut vir Mynbou en Metallurgie - Inligting Oor Lidmaatskap Die Instituut is in 1894 gestig as die Chemiese en MIetallurgiese Vereniging van ::!nid-Afrika. In 190-1is dit omvorm tot die Chemiese Metallurgiese en Mynbouvereniging van Sllid-Afrika en in 1956 het dit die Suid-Afrikaanse Instituut vir Mynbou en l\Ietallurgie geword.

Jan 2, 1976

By Bruce B. Redpath, Doug Crice, Rob Huggins

Over the last decade, instrumentation has been developed that allows the application of seismic reflection methods to groundwater and engineering problems. At the Geological Survey of Canada, we have been developing and testing shallow reflection techniques for mapping the bedrock topography and structure within the overburden. We have attempted to develop methods which can be implemented with a minimum investment in equipment and computing capabilities. The data are recorded on a l&channel engineering seismograph, using a single high-frequency geophone per channel, and a hammer or in-hole shotgun (“Buffalo gun”) as the seismic source. Processing and display of the data can be accomplished on an Apple II+ or IIe microcomputer and an Epson wide-track dot-matrix printer.

Jan 1, 1991

By Sam S. Taylor

Subsurface disposal of oil-field brines was practiced in Oklahoma on a limited scale as early as 1925. The technique of subsurface injection has been improved immensely and has been applied with varying success in many oil-producing areas in Oklahoma, and elsewhere. This method of disposal, however, is only one of several methods available to operators of oil-producing properties, but, in contrast with usual methods of handling brines on the surface it eliminates the damaging effect of mineralized water on fresh-water supplies, vegetation, and aquatic and other animal life. Other methods of brine disposal approved by regulatory agencies in some States include (1) impounding in impervious ponds and solar evaporation, (2) controlled diversion into surface waters, and (3) recovery of the mineral salts of the brine. In most, States where oil is produced regulatory bodies authorize the use of one or more of these methods of brine disposal. In Oklahoma, for example, the Oklahoma Planning and Resources Board of the Conservation Commission has been authorized to adopt whatever methods or means may be necessary to prevent contamination by mineralization of all potable waters within the State.

Jan 1, 1942