Search Documents

By N. Malakondaiah

Several growth chamber and laboratory experiments were conducted to study the germination behavior of plant species on mine spoils and plant growth responses to nutrients on spoils and topsoils. Experiments were conducted to study the germination potential of some native and introduced species under various conditions. The seeds of green needlegrass, side oats grama, thickspike wheatgrass, crested wheatgrass, birdsfoot trefoil and emerald crownvetch were less tolerant, whereas those of alkali sacaton. durar hard fescue, slender wheatgrass, yellow sweetclover and alfalfa were most tolerant to the sodic mine spoil conditions. Addition of leonardite improved the germination potential of some of the poor genninators. Slender wheatgrass and yellow sweetclover were used as test plants to study the fertility status and productivity potential of stockpiled topsoils and spoils collected from Center. Glenharold and South Beulah of North Dakota. The topsoils were neither saline nor sodic but low in N and P. The spoils were neutral to alkaline with SAIL of 12-32, EC of 1.8-5.5 mmhos/cm, Olsen&apos;s P< µ4g/g, and total N <0.07%. Application of N and P together to the topsoils increased the yield of wheatgrass and sweetclover by 88% and 70% of their respective maximum yields, whereas near maximum yields were obtained for both the species by the same treatments to the spoils. The average yields on topsoils were higher than the yields on spoils. The concentrations of major nutrients were higher in plants grown on topsoil, whereas the opposite was true with the concentrations of Mn, Zn, and Cu. Growth chamber experiments were also conducted to study the growth responses of alfalfa, oats and slender wheat grass by the application of Mn and Zn to a sodic coal mine spoil which was previously used for pot culture experiments. Significant growth responses to Mn and Zn were observed in alfalfa but not in oats or slender wheatgrass. Fertilizing the spoil with Mn along with NPK increased the yield of alfalfa to 85% and with Mn + Zn to 99%. Growth responses and plant composition results of this study confirm that the application of major nutrients to spoils can accentuate Zn and Mn deficiencies in some plants.

Jan 1, 1982

A mineral survey of the Rough Hills WSA (Wilderness Study Area) in northeastern Nevada was done by the U.S. Bureau of Mines in 1985 at the request of the Bureau of Land Management. The WSA is comprised of 6,685 acres of mountainous, desert lands within the Elko District of the Bureau of Land Management. The survey entailed investigations of prospects or mineral occurrences to provide information on possible resources within the WSA. No mineral resources were identified in the WSA. The only historical mining activity was for placer gold at the Prunty prospect at the confluence of Copper Creek and the Bruneau River. Total gravel at the prospect is about 6,500 cubic yards; however, the survey showed significant gold values (greater than $0.10 gold per cubic yard) only in the southwestern portion. There, however, the gravel averaged less than $1.00 gold per cubic yard, and only about 3,000 cubic yards are present, a grade and yardage insufficient to be of commercial interest. The occurrence, however, may have value for recreational mining by hobbyists.

Jan 1, 1986

By Qingwen Shi, Yun Zhao, Brijes Mishra

The effect of discontinuities on the fracturing and mechanical behavior of shale has been extensively investigated on a laboratory scale in previous works. It is well agreed that the lamination properties, including discontinuity and lamina properties, affect the behavior of shale. However, it is still unclear how the lamination properties are affecting the stability of the shale roof in an underground coal mine entry. This paper investigated the effect of lamination properties using the discrete element method on a mine-scale entry model as an extension to the previous work conducted on laboratory scale models.

Jan 11, 2022

By David A. Hall

We present an analysis of the propagation in a uniform tunnel of semi -circular cross section that contains two axial conductors. In particular, we show that, even if one of these conductors has high ohmic loss, one of the two propagating modes has relatively low attenuation. This corresponds to the situation where an unloaded dedicated wire is used to improve radio frequency communication in a mine tunnel that contains a heavily loaded trolley wire.

Jan 1, 1978

By Sidney Katell

This report, covering the period January 1969 through December 1969, is a continuation of a series that began with the publication of Information Circular 7516 in October 1949. It is the 11th in a series of reports prepared in cooperation with the American Association of Cost Engineers. The abstracted articles are concerned with all phases of cost engineering in the field of chemical and petroleum plants and related subjects. They are from the following sources: 1. American Association of Cost. Engineers Bulletin. 2. Bureau of Mines Information Circulars. 3. Bureau of Mines Reports of Investigations. 4. Chemical Engineering. 5. Chemical Engineering Progress. 6. Chemical Week. 7. Coal Age. 8. Coal Mining and Processing.

Jan 1, 1970

By David E. Swanson

The U.S. Bureau of Mines undertook a basic investigation of collimated abrasive water-jet behavior because a more complete understanding of the fundamental process may lead to further technical advances. Laboratory experiments used 2-mm water-jet nozzles and new entrainment apparatus to analyze collimated abrasive water jets operating under varied conditions. Maximum water pressure was 69 MPa to permit use of conventional hoses with a burst-to-operating-pressure ratio of 4. Nozzle and induction line pressures, abrasive induction rates, and jet reactive thrust forces were recorded for each operating condition. Average jet velocity and power were determined from component mass flow rates and reactive thrust force measurements. Relative velocity and cross-sectional distribution of abrasive particles were determined using impact analysis techniques. Other jet characteristics were determined photographically. Properties of free water jets, collimated water jets, and collimated air-water jets were determined for comparison.

Jan 1, 1989

[PRESIDENT E. DEGOLYER, District 0 NEW YORK, N. Y. PAST PRESIDENTS J. V. W. REYNDERS, District 0 . NEW YORK, N. Y. SAMUEL A. TAYLOR, District 3 PITTSBURGH, PA. FIRST VICE-PRESIDENT GEORGE OTIS SMITH, District 4 .WASHINGTON, D. C.]

Jan 1, 1928

Whilst the wider community is both a large consumer of mineral products and relies on mineral exports for much of the wealth which sustains it, the community generally has a poor perception of the minerals industry. &nbsp; The role of professionals and The AusIMM in the "New Economy" minerals industry is reviewed. The new structure of The Institute is vital as we move forward in times of globalisation, rationalism, increasing litigation, criminalisation of risk and increased focus on corporate governance. This address looks forward to ways The AusIMM and professionals of the future are positioning themselves for these and other challenges.

Jan 1, 2001

By Leon Maday, Dan L. Pecha, Jeremy Johnson, Daniel N. Adams

The Brightwater conveyance system includes 26 km of tunnels, a 130 mgd pump station, 2 km of micro tunnels, and a 2.4 km outfall. The tunnels extend from Woodinville to Puget Sound through varying soils in 1 to 7 bars of hydrostatic pressure and depths to 185 m. The tunnel diameters range from 4 to 6 m and include numerous lining systems. This paper highlights major shaft and tunnel design, including dual cellshafts, multiple pipe configuration tunnels, polymer concrete segments, and the use of a one pass lining designed to convey high pressure effluent.

Jan 1, 2005

By D. Arentsen

Changing environmental laws, new operating requirements and the increasing accuracy with which the bearing capacity of driven piles can be calculated have all led to the development of hydraulic piling hammers, some very primitive, others very advanced. Users find it difficult to decide which model is the most suitable, because the specifications are neither uniform nor unamiguous. There are no standard specifications and, moreover, the majority of hammers are suitable only for a limited range of applications. For the user, however, it is important to choose a hammer which will meet future as well as current requirements and will not quickly become obsolete or be unsuitable for a particular job.

Jan 1, 1987

Satellite Image Based Strategies to Evaluate the Impact of Dismissed Mine Site - An Application to the Mae Moh Coal Mine Area in the Lampang Province, Thailand

Sep 13, 2010

By Haitao Wang, Shen Wang, Dongyin Li, Yongjia Xu, Jinzhao Liu, Xiangjun Chen

The safe and efficient driving of the roadway along the gob is becoming an increasing challenge due to the influence of the integrity and bearing capacity of the side coal and rock mass in the gob under the roof cutting mining mode. The mechanism of protection of the gob-side roadway is shown by modeling the influence of roof cutting and the application of a destress technique on the lateral coal and rock mass zones. The distribution characteristics of stress, displacement, and fracture in the overburden are analyzed by numerical simulation method under the three working conditions. The results indicate (1) construction of row holes and blasting can form artificial structure’s fracture plane above the roadway, which can effectively cut the connection of overburden. The artificial structure’s fracture plane decreases the peak value of the lateral coal body’s support pressure. The peak point and the critical location of the stress reduction area are both transferred to the deep part at the same time, providing adequate space for the gob-side roadway. (2) The stress arch foot in the lateral rock mass rises to the rock layer at the bottom of the roof cutting plane after top cutting, as does the high-pressure area of deviator stress. The fracture plane prevents lateral coal and rock mass instability and limits the negative effects of roof deformation above the gob-side roadway. (3) The triangle slip fracture zone moves to over the roof cutting drilling zone due to the fracture plane, showing a high position compared to its original zone.

Jul 11, 2023

By John Cory, David Lily, Bill Hissem

The Lafarge granite quarry in Cumming, Georgia is using Principal Component Analysis (PCA) and Biplot charting to identify important variables and control air blast and vibration. Every blasting situation is unique and PCA and Biplot charting help to clarify the major variables determining air blast and vibration.

Jan 1, 2010

By T. T. Tomimatsu

[This Bureau of Mines paper investigates explores, and analyses the Corporate structure dynamics and Rancid role to evaluate the economic health of the U.S. copper producers. It highlights the Corporate policy options and measures of corporate profitability and suggests that a competitive domestic copper industry will exist in the future. The study highlights the activities of 14 selected major copper-producing companies, including their subsidiaries o affiliates, that were responsible for more than 95 percent of the total U.S. production in each of the years since 1969. The selected firms are hot all primarily in the business of producing copper. Several of the large producers are classified by the financial institutions as integrated oil and gas enterprises.]

Jan 1, 1980

By Arthur Crowfoot

This paper describing t o concentrating practice of the Phelps Dodge Corporation, Morenci Branch, at Morenci, Ariz., is one of a series of articles on concentrating methods and posts being prepared by the Bureau of Mines. The Morenci concentrator, locally known as No. 6 concentrator, treats 5,000 dry tons of ore per 24-hour day by primary tabling followed by two stages of flotation treatment, at 48-mesh size and 65-mush size respectively.

Jan 1, 1931

From Sept. 22-24, the Las Vegas Convention Center will be home to MinExpo 2008, the world?s largest mining equipment show that comes along once every four years. Sponsored by the National Mining Association (NMA), this year?s show is on pace to be the largest ever. Nearly 1,300 exhibitors have purchased nearly 55,700 hm2 (600,000 sq ft) of booth space. At the center of it all will be some of the most impressive mining equipment that the industry has to offer. And in the shadows of the massive haul trucks, drill rigs and bulldozers, attendees will be able to see the latest and greatest products including hand tools; the latest in automation and robotics; safety and communications equipment; longwall mining equipment; engines and parts; materials handling and processing equipment and services; pollution control equipment; reclamation equipment and services; computer applications; consulting and financial services and more. While many companies will be on hand to display the tried and true, there will also be plenty of new things to see. ?We anticipate that a whole range of new products will be introduced at the show,? the NMA said of the show that has been called the world?s richest deposit of mining technology, services and products. In addition to the show that will take place in Center Hall and North Hall of the Las Vegas Convention Center, MinExpo 2008 includes a conference program with 20 educational sessions that will tackle the most timely and pressing issues affecting the mining industry. Many of the industry?s top professionals will lead the discussions.

Jan 1, 2008

By Nozomu Kotake, Rakshya Shrestha, Ralph Griffin, Stefanos Papadopulos, Jeff Fippin, Sushil Kafle

Direct Power Compaction (DPC) is a deep Vibro-compaction method used for liquefaction mitigation. In DPC, H-beams are used as vibrating rods penetrating deep into the ground, and a vibrating force is applied directly to the tip of these H-beams to densify the loose ground. A characteristic feature of DPC is the use of a flapping plate installed at the base of the H-beam to enhance the compaction efficiency during penetration. In addition, 2-rod and 4-rod type equipment have been developed to improve productivity and enable rapid construction. DPC was selected as the most suitable and cost-effective technique to mitigate liquefaction hazards in two projects in the San Francisco Bay Area, one on Alameda Island and another on Treasure Island. Both sites were capped with hydraulically placed sand fills. Liquefaction analyses indicated excessive liquefaction-induced settlements and large lateral spread without ground improvement. Densification using DPC was performed up to depths of 42 ft to reduce the liquefaction potential of the sand fill to acceptable levels and to allow planned improvements. Cone penetration tests were conducted before and after DPC to evaluate its performance. This paper describes the equipment and process involved in DPC and discusses its application in terms of subsurface conditions and geotechnical design considerations.

Sep 8, 2021

In 1967 the United States consumed 58.8 quadrillion Btu of energy. Both the Atomic Energy Commission and the Resources for the Future, Inc., a private economic forecasting group, predict that the United States energy requirements will reach 135 quadrillion Btu by the year 2000. In 1967 bituminous coal produced 21.4 percent of the energy used in the United States and anthracite coal another 0. 5 percent. Coal Reserves Coal reserves make up about four-fifths of the United States storehouse of fuel in proven reserves. Seventy-five percent of all fuel, likely to be found and recovered is coal. Electric utilities consume more than half of the bituminous coal mined in the United States in generating 53 percent of the nation&apos;s electricity. Atomic Energy Commission analysts have proposed the development of a vast "national energy system" based upon long-distance electrical transmission from abundant untapped coal reserves in the western United States. The study predicts that even if uranium supplies are available and economic breeder reactors developed, coal requirements for electricity generation will more than double by 1980 and increase another 50 percent before the year 2000.

Jan 1, 1970

By James P. Bennett

To identify construction materials for emerging technology in chemical and metallurgical processes, the Bureau of Mines investigated the acid resistance of ceramic materials. Eight commercial ceramic materials comprising two red shale, two fire clay, a silica, a five-claybonded silicon carbide, a carbon, and a high-alumina brick were evaluated. Samples were exposed for 110 days to 20 wt pct HCl at 50°, 70°, and 90° C and to 30 wt pct HCl at 70° C. Statistically significant changes in cold crushing strength, volume, and weight were generally small or not detected. The leach rates of Al, Ca, Fe, K, Mg, Na, Si, and Ti ions were monitored. The carbon brick sample had the best acid resistant properties with a maximum total leached ion weight loss of 0.004 wt pct. The silicon carbide, the silica, and one of the fire clay bricks also had excellent acid-resistant properties.

Jan 1, 1983

Organization Place Date 1919 Automotive Engineers New York, N. Y. Feb. 4-6 American Institute of Mining Engineers New York, N. Y. Feb. 17-20 New England Association of Gas Engineers Boston, Mass. Feb. 19 American Institute of Electrical Engineers New York, N. Y. Feb. 19-21 National Society for the Study of Education Chicago, Ill. Feb. 25-28 American Railway Engineering Association Chicago, Ill. Mch. 18-20 American Electrochemical Society New York, N. Y. Apr. 3-5.

Jan 2, 1919