Search Documents

By Anthony E. Szczuka

Two facets of surface mining were studied: feasibility of using training simulators to increase productivity of haulage trucks, front-end loaders, and shovels; and improving the efficiency of dragline operations with a computer-aided analysis of dragline usage and the addition of an on-board operator display. Training costs per student were estimated based on current training practices. Training objectives were derived from task: analyses of haulage trucks, front-end loaders, and shovels. The cost effectiveness of training simulators was determined. A computer-aided analysis defined the critical performance parameters. An on-board operator's display is recommended to improve operator efficiency.

Jan 1, 1976

By Fisher N. I

Disequilibrium ratios (U3O8/eU3O8), which assess the degree to which gamma activity represents the uranium content of a sample, have been measured on a representative set of samples from the ore zone of a carnotite ranium deposit located at Yeelirrie, Western Australia. A statistical analysis has been performed to investigate the dependence of the ratios on lithology and on the location of the sample in the orebody. The analysis indicates that dependence on lithology and on position across the orebody is negligible. Samples from the western end of the orebody and those from below the water table level tend to have slightly lower ratios than samples from other positions, although these trends are small compared with a large random variation in the data. The large random variation could result from some redistribution of the daughter isotopes of uranium within the orebody. On the basis of the results from all the samples, the estimated deficiency of uranium relative to radium in the ore zone of the deposit is 11 per cent.

Jan 1, 1980

By B. Genc, P. Malepfane

This study proposes a new approach to reduce the environmental impact during surface mining by improving environmental factors through the incorporation of carbon footprint into strategic mine planning. Two key variables were analysed by contrasting and comparing the baseline and optimised models generated. These variables include net present value, which helps determine the financial feasibility of the mining models and their carbon emissions. The variables were analysed by using linear regression, Spearman’s correlation, a P-value hypothesis, and an exponential decay test. Results show that at Mine A the projected net present value was 62% higher than when running a baseline model. Furthermore, the net present value from the baseline model portrayed a high rate of decay at 0.667 versus 0.118 from the optimised model. This indicates the baseline model’s sensitivity to long-term project timelines and fluctuating markets. The optimised method presents an opportunity to manage emissions during the high operational costs phases. It is represented by a 31% improvement in carbon emissions during the periods of high operational costs, whilst maintaining a positive net present value when compared with the baseline model. It was shown that the optimised model presents a better chance of achieving financial feasibility and balancing environmental impact, thereby ensuring that Mine A can align with the environmental aspect of economic, social, and governance principles through lowering the carbon footprint resulting from its hauling operations.

Jan 30, 2026

By R. F. Selden

The material in this paper is intended simply, to be an inquiry into some of the theoretical aspects of the occurrence of methane and carbon dioxide in coal, with a brief resume of the more recent literature. Several discussions on various phases of the subject have been published, a few of which (4, 20, 25, 88, 90)4/ have more or less extensive bibliographies of tie earlier literature. In large measure the pertinent literature deals with the unusual aspects of the subject, and in consequence it might appear that the normal aspects have not been given due consideration here. The latter information is largely a matter of practical field experience, and since that which is normal to one locality is often abnormal to another no sharp differentiation appears to be necessary or, in fact, possible. No attempt will be made to present a critical discussion of the relations between the presence of gases in coal and pertinent geologic features or mining practice. Although the presence of foreign gases in the ventilating air of many mines is not particularly noticeable, in many others the evolution of methane and perhaps small amounts of carbon dioxide (or sometimes the reverse - large amounts of carbon. dioxide with perhaps sore methane) is quite apparent.

Jan 1, 1934

By Joel N. Van Sant

An investigation was conducted to study possible sources of Utah refractory and structural clays that could be used for the manufacture of refractories and light or buff burning heavy-clay products. A field study was made and the clay samples tested to determine their firing characteristics. Results of the Bureau's work indicate many small noncommercial deposits of hypogenic clay occur in igneous rocks. Commercial hypogenic deposits are mostly halloysite clay developed by hydrothermal replacement of limestone. The high firing shrinkage of halloysite precludes its use as a refractory, however, halloysite produced at the Dragon Mine south of Eureka, is used fur making oil catalysts. Clays and shales suitable for low heat duty refractory products are found in the Manning Canyon shale, in shales associated with coal bearing rocks, and in the Dakota formation. Some of the clays from the Dakota formation are also suitable for high-duty refractory products.

Jan 1, 1964

By W. A. Gibson, A. D. Trujillo

The Santa Rita copper deposit first served as a source of native copper for Indian implements and weapons. In 1801 Santa Rita copper, trans- ported by mule train to Chihuahua, began to be used commercially for making coins. It was a small- scale operation made difficult by Indian raids, transportation costs and depletion of the higher grade ores. There was, moreover, no known method for economically extracting copper from the under- lying low grade sulfide ores. Originally, copper and copper oxide ores were mined by underground methods, but there was virtually no development of the deposit-which became United States territory after the Treaty of Guadalupe Hidalgo in 1848-for almost a hundred years. A number of small underground mines had been started during that time, but it was not until 1873 that all the principal claims were consolidated under one control.

Jan 1, 1966

By O. H. Metzger

This is one of a series of capers being published by the Bureau of Mines on gold mining A the Western States. It describes the production of gold in the principal mining districts of New Mexico. The material was gathered red on a trip through tale State in the summer of 1936. ACKNOWLEDGMENTS The author acknowledges the aid and cooperation of mine operators in all parts of the State, who willingly contributed all information requested. Geological reports of the Geological Survey and the New. Mexico Bureau of Mince were drawn upon freely for information; credit to individual paper, is given in the text.

Jan 1, 1938

By Thomas Curtin

The Bureau of Mines, in its researches aimed to prevent wastes and to increase efficiency in oil-well practice, has investigated the matter of casing troubles and fishing methods. The results of the investigation are set forth in this paper. After expensive development work, many wells being drilled for oil have been abandoned because of casing troubles. These troubles in many instances have been thought to be insurmountable, whereas they are sometimes susceptible of solution. In fields_ where casing difficulties are of daily occurrence, methods have been evolved for combating them. Were these methods more widely known and applied wherever the same conditions exist, the oil industry at large would be greatly benefited. This report attempts to classify these troubles and suggests solutions that will save the operator discouragement and expense. It is assumed throughout this paper that the reader is so familiar with the ordinary oil-well drilling and fishing methods that detailed explanation is unnecessary. The well-drilling terms that are used herein will be readily understood by those for whom this discussion is intended. However, in order to avoid confusion as to the sense in which some of these terms are applied, definitions &re included.

Jan 1, 1920

By I. M. Richardson, M. Janssen, W. Geerstma, I. J. Bennett, V. A. Popovich

Avoiding wafer breakage is a big challenge in the photovoltaic silicon industry, limiting production yield and further price reduction. Special fracture strength tests suitable for thin silicon solar wafers and solar cells, to be used in combination with Weibull statistics, finiteelement (FE) modelling and digital image correlation have been developed in order to study the mechanical stability of solar wafers. The results show that removal of the saw damage significantly increases the strength of crystalline silicon wafers. Furthermore, it was found that silicon crystallinity and the location where the wafer is extracted from the cast Si ingot have a significant effect on the strength, namely samples taken from the bottom of the ingot are 30% stronger than those taken from the top. The study also showed that there is a decrease in fracture strength when an anti-reflective SiNx coating is applied, which is caused by high thermal stresses.

Jan 1, 2015

By H. W. Gillett, G. M. JAMES

In its work on mineral wastes the Bureau of Mines is studying losses in the melting of nonferrous metals and alloys. The greatest of these losses is that of zinc through volatilization in brass melting, but another and considerable loss is that of aluminum and its alloys in the melting of finely divided material. In order to get some idea of the magnitude of the loss in melting aluminum scrap and to find out what methods of melting were used information was gathered in regard to present practice; also experiments were conducted to obtain some data on the relative merits of different methods. As the experiments could be made on a laboratory scale only, they were not expected to solve the problem entirely, the object in making them being rather-by indicating which methods were of greater promise-to narrow the field over which largescale tests and comparisons need be made by those commercially nterested in the problem of melting scrap aluminum.

Jan 1, 1916

By S J. Clarke, C S. Walker

The South West Rail Link (SWRL) project involved construction of a rail line to service new residential areas in south-west Sydney. The 11 km rail line is conveyed through a short tunnel at shallow depth where it crosses beneath the eight lanes of the Hume Highway. The underpass location is one of the most heavily trafficked within Sydney’s motorway network.The New South Wales Roads and Maritime Services (Roads and Maritime), as the owner of the highway asset, had the responsibility of managing the risks to the highway and traffic associated with the tunnelling project from the pretender stage through to completion. This paper considers the primary risks and mitigation measures employed, including geotechnical investigation, and development of appropriate construction constraints and concept design of an extensive real-time survey system to monitor pavement deformation during the tunnel works.The geology comprises fresh Minchinbury Sandstone in the tunnel invert and side walls, and variably weathered Bringelly Shale in the haunch and crown. Few tunnels have been excavated in these rock types in Sydney, and there is little information relating to the in situ stresses and stress-relief deformations in these materials.During tunnel construction the monitoring data indicated unexpected surface heave of up to about 24 mm. A multiparametric back-analysis of the deformation data is presented, which provides information on the deformation mechanisms and key geotechnical parameters, including rock mass modulus and in situ stresses.The approaches and methodologies developed for the SWRL underpass were effective in maintaining the safe operation and traffic capacity of the highway throughout the construction period, and the analysis of the monitoring data provides a useful reference for similar future projects, or projects constructed in similar ground conditions.CITATION:Clarke, S J and Walker, C S, 2014. Deformation mechanisms of the South West Rail Link underpass beneath the Hume Highway, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 631–640 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By R. F. Selder

The material in this paper is intended simply to be an inquiry into some of the theoretical aspects of the occurrence of methane and carbon dioxide in coal, with a brief resume of the more recent literature. Several discussions of various phases of the subject have been published a few of which (4, 20, 25, 88, 90) have more or less extensive bibliographies of the earlier literature. In large measure the pertinent literature deals with the unusual aspects of the subject, and in consequence it might appear that the normal aspects have not been given due consideration here. The latter information is largely a matter of practical field experience, and since that which is normal to one locality is often abnormal to another no sharp differentiation appears to be necessary or, in fact, possible. No attempt will be made to present a critical discussion of the relations between the presence of gases in coal and pertinent geologic features or mining practice. Although the presence of foreign gases in the ventilating air of many mines is not particularly noticeable, in many others the evolution of methane and perhaps small amounts of carbon dioxide (or sometimes the reverse - large amounts of carbon dioxide with perhaps sore methane) is quite apparent. The presence of small quantities of carbon dioxide can be attributed to oxidation of the carbonaceous matter exposed to the air. In the few cases in which this explanation is not sufficient, obviously the carbon dioxide must escape as such from the coal and neighboring strata.

Jan 1, 1934

By D. Denton, M. Stickney, R. Langston

The National Institute for Occupational Safety and Health and the Stillwater Mining Company worked cooperatively with the Montana Bureau of Mines and Geology to develop a system that would collect seismic data at the Stillwater and East Boulder mines. The purpose was to obtain baseline information on the magnitude and location of mining-induced seismicity to determine if the mines needed multi-channel in-mine monitoring systems. Seismic data recorded at field sites near the mines are being telemetered via FM radio through a series of repeaters to a central recording site where the seismic signals are digitized using an Earthworm data acquisition system. The Earthworm system performs several data analysis tasks in near-real time and places raw seismic data, preliminary hypocenter locations, and magnitudes on a Website within 5 min of a seismic event. Such rapid access to seismic data allows personnel at the Stillwater Mine, Spokane Research Laboratory, and Earthquake Studies Office to evaluate seismic events quickly and respond in ways that may improve the safety of mine personnel underground. Installation of the system also broadened earthquake coverage to south-central Montana, a region previously not covered by the seismograph network.

By J. F. Brune, A. Verma

"Face ignitions in underground coal mines are a major risk for underground mining operations, as they can lead to methane or coal dust explosions. The 2010 disaster at the Upper Big Branch Mine resulted in 29 fatalities due to a methane and coal dust explosion initiated from a face ignition. Much research has been conducted to mitigate face ignition hazards, from water sprays to installing passive and active explosion barriers. Despite the increased use of water sprays in U.S. coal mines, there have been more than 50 documented face ignitions in the U.S. underground coal mines since 2010, indicating that this hazard still prevails. This paper will examine the statistics of face ignitions and gas explosion in U.S. coal mines based on MSHA data. It will study factors contributing to these face ignitions and outline best practices for their prevention based on experience and practices worldwide. INTRODUCTION Methane and coal dust explosions are one of the major causes of coal mine disasters in the U.S. and around the world. Such disasters have resulted in the large number of fatalities and loss of mine infrastructure. The recent explosion at the Soma coal mine in Turkey has caused the death of 301 miners (Mining Turkey, 2014). As documented by U.S. Mine Safety and Health Administration (MSHA, 2015a), the U.S. coal mining industry has also experienced several catastrophic mine explosions with accidents at Upper Big Branch mine, Darby mine, Sago mine and Jim Walter Resources No. 5 mine in the last decade, causing the deaths of almost 60 miners. Every explosion requires a source of ignition, the right amount of fuel and oxygen. In underground coal mines, methane acts as a fuel while ventilation air acts as a source of oxygen. The source of ignition may vary from spontaneous combustion, electrical equipment and switchgear, mechanical heat sources, face ignitions due to friction rock-on-rock or from cutter bits and lightning strikes. Under the right conditions, energy of less than 0.3 mJ is sufficient to ignite methane-air mixtures (James, 2007) that can result in a catastrophic explosion. Much research has been done to mitigate the methane explosion hazard by proper dilution, continuous monitoring of methane and elimination of ignition sources. Historical studies indicate that face ignitions are the major cause of explosion in underground coal mining operations worldwide (Belle, Carey, and Robertson, 2012). Statistics shows that most mine disasters were started from a small face ignition, which turned into a major explosion fueled by additional methane and coal dust (Belle et al., 2012). To investigate face ignition hazards, researchers must study potential ignition sources as well as potential explosive atmospheres near mechanical coal cutting operations. Statistical analysis of U.S. coal mine face ignitions reported by the U.S. Mine Safety and Health Administration (MSHA, 2015b) shows that several factors are responsible for face ignitions."

Jan 1, 2016

By Trevor R. Ellis

Minerals appraisers/valuers often find great difficulty in attempting to employ the sales comparison approach to the market value appraisal of development and operating stage mineral properties. An important factor generally overlooked is a comparison of net operating income (NOI) margins on a per-unit-of-production basis between mineral properties, whether these be demonstrated or forecast margins. NOI margins can vary greatly between mines or quarries that are producing similar products. Ultimately, the expected NOI margin determines what a buyer is willing to pay for an income-producing property. Here, common criticisms of the sales comparison approach by mineral appraisers are introduced. These are counterbalanced by raising some issues in the way the inputs for the income approach are usually derived by minerals appraisers and by review of some conspicuous examples of the much-too-common misuse or abuse of the income approach in market value mineral appraisals. Example transaction analyses and sales comparison analyses are used to demonstrate the author?s methodology for adjusting units of resource in his transaction adjustment tables. The examples are used as the basis for a discussion of ways to employ adjustments for operating economics and many other factors, while warning against the potential for double counting. The conclusions include a recommendation that minerals appraisers attempt to apply at least two of the three valuation approaches when appraising the market or fair value of development and operating stage mineral properties, the two being the sales comparison and income approaches.

Jan 1, 2011

By G. B. Harris

It has long been appreciated that chloride chemistry has a number of advantages over the more traditional sulphate route for both extracting and separating metals. Modern materials of construction, coupled with the development of a more cost-effective and efficient hydrochloric acid regeneration technology mean that chloride-based processes are now more competitive and attractive. Such processing routes are able to recover more of the contained metal values in a feed, including iron in a benign and/or marketable form, and particularly the so-called rare and rare-earth elements which are increasing in demand in our electronic age. These factors, therefore, add appreciably both to the overall economics of a project, but also offer a much more sustainable approach to our dwindling natural resources. Additionally, chloride-based flowsheets can be much more environmentally-friendly, offering practical alternatives to two of the biggest headaches faced by the industry, namely cyanide usage and the generation of red muds. This paper presents a brief theoretical background, focusing on the latest developments of ferrous iron oxidation and the low-temperature, selective hydrochloric acid regeneration process, which is the key unit operation for any chloride flowsheet, and discusses in general the advantages of the chloride approach. Several recently-developed flowsheets, which have been tested at the miniplant level, are presented for gold, base metals, titaniferous magnetites and lead-silver ores wherein the advantages of considering a chloride approach are highlighted.

Jan 1, 2014

THE Synthetic Liquid Fuels Act. (30 U.S.C., 321-325, and amendments) became law April 5, 1944, and a period of intensive research and development in this field was begun by the Bureau of Mines. As part of this program, bulletins were published on pressure hydrogenation.3 the Fischer-Tropsch synthesis,4 anal oil shale.5 The Bureau also has published a short bibliography on coal gasification,6 mostly of a theoretical nature. Because coal gasification is prerequisite to either the Fischer-Tropsch or coal-hydrogenation processes, publishing this sizable collection of technical information in this form will be valuable. The material will be presented in three parts, as follows: I. United States Patents. II. United Kingdom Patents. III. Other Foreign Patents. The domestic patents for this bulletin were collected between 1953 and 1955.

Jan 1, 1960

By E. S. Chalpin

On 25 August 1971, the U.S. Bureau of Mines contracted with the Aerojet Liquid Rocket Company to perform an engineering research program to be completed on 25 May 1972. The program objective was to evaluate the advantages and disadvantages of the underground use of several power sources including but not limited to a closed cycle diesel, electric cable/motor, rechargeable battery/ motor and exhausting diesel for mine shuttle cars, with emphasis on health and safety. This report, Research in Advanced Power Systems for Mining Health and Safety consists of four (4) main parts: (1) Hazards and Safety Analysis of Mine Power Systems, (2) Evaluation of Closed Cycle Diesel Power System for Mine Applications, (3) Closed Cycle Diesel Power System Consumables Compatibility, and (4) Concluding Remarks and Recommendations. The hazards introduced to a mine by shuttle car power system failure modes were evaluated and reported. A "fault tree" analysis was generated for each power system and the probability of death or injury during an eight (8) hour shift and for a week of operation (105 hours) were estimated. Advantages and disadvantages were also reported for each system studied. Aerojet's assessment, based on a "forced decisions analysis," of the four shuttle car power systems as to their relative health and safety is that the exhausting or open cycle diesel is preferred, followed by the closed cycle diesel, the electric cable/motor and the rechargeable battery/motor. The assessment was based on ten parameters pertinent to the health and safety aspects of shuttle cars. Drawing layouts of two typical mine shuttle cars incorporating closed cycle diesel powerplant concepts are included in this report. The performance parameters established for the two concepts are tabulated. A study was made of the logistics involved in transporting and replenishing the consumables needed to operate a shuttle car equipped with a closed cycle diesel. The closed cycle diesel powerplant consumables -oxygen, potassium hydroxide, and diesel fuel - were analyzed as to their compatibility with materials found normally in a gassy coal mine. Spill tests simulating inadvertent leakage of liquid oxygen in a coal mine were performed. A critical evaluation of existing oxygen sensitivity data and the relationship to the use of oxygen on a shuttle car in a coal mine environment is presented.

Jan 1, 1972

By Wilmer McInnis

MOLYBDENUM, one of the more versatile alloying elements in modern metallurgy, was first isolated by Hjelm in 1782. The pure metal is silvery white and softer than steel. It melts at a higher temperature than all other metals except rhenium, tungsten, and tantalum. Molybdenum, a member of group V of the periodic table, chemically exhibits valences in stable compounds of 2, 3, 4, 5, and 6. It is a strong carbide-forming element, and much of its alloying effect in steel is imparted through the formation of carbides. Molybdenum occurs in nature only in combination with other elements. The most common occurence is molybdenite (MoS2), which is widely distributed throughout the world; the few known commercial deposits are the major sources of molybdenun1. The other commercially important mineral, wulfenite (PbMo04), was a major source of molybdenum in the United States during the early part of the 20th century, but with exploration and development of the world-famous Climax molybdenite deposit during the World War of 1914-18, molybdenite soon became the world's major source of molybdenum. In recent years, virtually no wulfenite has been mined. Many copper deposits contain minute percentages of molybdenite; and, since the inauguration during the early 1930's of the recovery of molybdenite as a byproduct of these deposits, they have been an important source of molybdenum.

Jan 1, 1957

By Nan Hua

As a high production and high efficient mining method, top coal caving method is now widely used in China. However, as more extra-thick coal seams are mined, it becomes more and more difficult to make the top coal fully broken up, resulting in more and more top coals flowing into the gob, rather than onto the rear AFC at the working face as designed. This research is aimed to investigate the failure mechanisms of the extra-thick top coal caving mining method.

Jan 1, 2009