Search Documents

By V. Velicka, J. Ptacek, R. Snuparek, P. Konecny, G. Takla

Coal mining in Ostrava-Karvina coalfield is being accompanied by rockbursts. 82 rockbursts occurred within the period between 1990 and 2002. Natural and technological factors from these rockbursts were collected and analysed. They confirmed that rockbursts are complex geomechanical events and that the relations between co-acting technological and natural factors are very complicated. Der Abbau in dem Ostrava-Karvina Steinkohlenrevier wurde von Anfang an durch Gebirgsschläge begleitet. 82 Gebirgsschläge in dem Zeitabshnitt von 1990 bis 2002 erfolgten. Die Angaben über natürliche und technische Faktoren der Gebirgsschläge wurden gesammelt und analysiert. Es wurde bestätigt, dass die Gebirgsschläge komplexe geomechanische Phänomene sind und dass die Beziehungen zwischen den zusammenwirkenden Faktoren sehr kompliziert sind. L´abattage d´houille dans le Bassin houiller d´Ostrava-Karvina est accompagnée par les coups de terrains. 82 coups de terrains s´étaient produit dans la période entre 1990-2002. Les données sur les facteurs naturels et techniques ont été ramassées et analysées. Les résultats ont corroboré que les coups de terrains sont des phénomènes géoméchaniques complexes. Les relations entre les facteurs techniques et naturels coopérants sont très compliqués.

Jan 1, 2003

By Wm. O. Vanderburg

This paper describing the milling methods at the Hughesville concentrator of the St. Joseph Lead Co., Hughesville, Mont., is one of a series of similar papers being prepared by the U. S. Bureau of Mines on practices at the various mills in the United States. The writer expresses his thanks for the courtesies extended by the officials of the company while visiting the property and acknowledges the assistance and helpful suggestions given by R. H. Willcomb, general manager, and Carl Martin, mill superintendent, of the Hughesville Division f the St. Joseph Lead Co.; and E. D. Gardner, supervising engineer, U. S. Bureau f Mines, Southwest Experiment Station, Tucson, Ariz., in gathering and compiling the data herein presented.

Jan 1, 1931

Marble deposits of dolomitic variety are available in large quantities in India and for extracting these deposits diamond wire saw cutting machine is mainly used. Cutting performance of the diamond wire saw machine depends on rock parameters, machine parameters and operational parameters. Rock parameters related to physico-mechanical properties, such as, compressive strength, tensile strength, shear strength, modulus of elasticity and abrasion resistance of marble play role in determining cutting rate and beads wear rate. Thus, this study was undertaken to determine the relationship between different physico-mechanical properties and cutting performance. This work also aimed at enhancing the cutting performance of diamond wire saw in dolomitic marble deposit. Study was conducted in the field at three different zones having deposit of soft, medium hard and hard dolomitic marble. During the study, cutting rates and wearing of diamond beads were recorded in the field. Physico-mechanical properties were determined in the laboratory. The results obtained were subsequently evaluated by using statistical analysis. Study revealed that these properties of marble play a significant role in the performance of diamond wire saw machine. Predictive equations for the wearing of diamond beads and cutting rate were developed based on regression models. Results of this study will be of ample use for operators of wire saw to achieve maximum cutting performance and for manufacturers in designing the diamond beads.

Dec 6, 2010

By Yoginder P. Chugh

The characteristics of weak floor strata associated with actively mined coal seams in Illinois are very important from ground stability point of view and, in many cases, are the governing factors in determining the size of pillars and mine openings. Laboratory and field getotechnical characterization studies of weak floor strata were conducted at six mines during the period 1985-1988. Correlation analysis among engineering index properties, and laboratory, and field determined strength-deformation properties were conducted to identify simple tests which can be used to estimate ultimate bearing capacity and deformation properties of immediate floor strata. It was concluded that the ultimate bearing capacity (UBC) and strength- deformation properties of the weak floor strata can be estimated from simple tests such as, natural moisture content, atterberg limits, and axial swelling strain. Indirect tensile strength was found to be a better estimator of UBC than unconfined compressive strength.

Jan 1, 1989

By C. R. Summers

In response to the Coal Mine Health and Safety Act of 1969, mandatory noise standards have been developed that specify time-noise limits of mine personnel exposure. Most affected by elevated noise levels is the pneumatic roof bolter operator, both in terms of levels near or in excess of 115 dbA and in terms of length of exposure. Therefore, the principal emphasis of this Bureau of Mines report is on pneumatic drill noise control. It is not the intent of this report to suggest any drill redesign; instead, methods are suggested to reduce the noise level by complementing existing machines. An integral muffler system and a separate muffler system were tested in an attempt to lower pneumatic drill noise levels. Pneumatic drills, when new, operate at about 115 dbA when drilling in sandstone. Using the drill muffler systems, it was possible to decrease the noise level of a 115-dbA stope drill to approximately 100 dbA.

Jan 1, 1974

By Mario Samamé Boggio

El presente texto describe algunos aspectos de la inversión extranjera en tres períodos: fines del siglo XIX, la primera mitad del siglo XX y segunda mitad del siglo XX. Dentro de lo quince casos analizados se halló que 5 empresas son iguales: Northern, Southem, Santander, Santa Luisa y Madrigal; 4 empresas se han "peruanizado" total o parcialmente: Caylloma, Ticapampa (Alianza), Lampa (Minsur) y Ruaron, 3 empresas se han agotado aparentemente: Santo Domingo, Salinas y Minas Ragra, 1 yacimiento revertió al Estado y fue desarrollado por Minero Perú: Cerro Verde; y 2 empresas fueron expropiadas y estatizadas: Cerro de Pasco Corporation y Marcona. En todos los casos no hubo descubrimiento del yacimiento por el inversionista, quien compró las concesiones y denuncios, con excepción de Marcona que estuvo explorado y desarrollado y fue contratado para su explotación.

Mar 1, 1982

The importance of the minerals industry to any economy is clearly demonstrable. Its raw materials and products are the foundation of modem society and they have shaped the history of mankind from prehistoric times to the space age of today. However, those in the minerals industry have clearly failed to impress this fact on the consciousness of the public, bureaucrats and politicians. They have also failed to engage their dedicated opponents in a constructive debate. This is mainly because the minerals industry has been unwilling (until recently) to deal with the "soft" issues of civil society, nor understand and operate on a more emotional level. Technical professionals (as well as managers) in the future must be as comfortable in handling community concerns over social, environmental or landowner issues, as they are with logging complex drill core, designing blast patterns and separating one mineral from another. They must become caring, effective communicators and mediators. These are the new skills of a professional in the Third Millennium. These issues are outlined and discussed with some Australian data used to illustrate the point. If there is to be a future for all, then the policy makers within all levels of government (national, regional or local) must not drive essential mineral development offshore. They must address ways to support wealth creation mechanisms, particularly innovation. The minerals industry is a powerful wealth creator for ordinary citizens and an innovator. Politicians and their advisers must not .be allowed to forget this fact. If the ANZAC minerals industries do not win the emotional debate and successfully deal with the "soft" issues as well as they deal with the technical issues, there can be only a dim future ahead.

Jan 1, 2000

By Michael Wieland

For shooting rock properly, some relatively fixed quantity of rock work is required from the total charge mass, while keeping the overall toxic fumes to a minimum. The overall fumes weighted for the toxicity of different species and taken per unit charge mass, ??, are represented by a relative fume toxicity (RFT) formula. The worst two contributions are often carbon monoxide {CO} and total nitrogen oxides {NOX}, so the traditional Russian formula RFT-R formula suffices, though a generalized form RFT-G with more terms is worth checking. Using the work-principle model from thermodynamics, the rock work per unit charge mass, ??, is found from the reduction in internal energy for the reaction zone. This resolution technique for rock-work invokes the usual assumption that the quick irreversible process occurs without notable heat transfer to the rock (adiabatic); rock-work is not resolved, when this restriction is untenable. The ratio of ?? to ?? yields the weighted toxic fumes divided by the rock work or the readjusted fume toxicity ??, where ?? = ??/??. For convenience, graphical trends of ??, ?? and ?? were normalized using reference results for a stoichiometric (ANFO) mixture of ammonium nitrate (AN) and fuel oil (FO) shot under nominal rock confinement, noted later.

Jan 1, 2006

By W. G. Miller

An overall study was conducted to evaluate the properties and processes influencing the rate and magnitude of consolidation for oil sands fine tailings produced using different extraction processes. As part of this overall study, consolidation tests using slurry consolidometers were carried out for caustic and non-caustic fine tailings. The influence of a change in bitumen extraction process (caustic versus non-caustic) on consolidation properties, namely compressibility and hydraulic conductivity, was determined, as was the effect of adding a coagulant (calcium sulphate [CaSO4]) to caustic fine tailings. For fine tailings originating from two different oil sands ores (Ore A and Ore B), results were presented in terms of variation in average void ratio with time (settlement), void ratio with effective stress (compressibility), hydraulic conductivity with void ratio and coefficient of compressibility and hydraulic conductivity with sodium adsorption ratio. Findings indicated that chemical characteristics of fine tailings (water chemistry, degree of dispersion) do not have a significant impact on their compressibility behaviour and have only a small influence at high void ratio (low effective stress). The biggest advantage of non-caustic fine tailings and treating caustic fine tailings with coagulant is an increased initial settlement rate and slightly increased hydraulic conductivity at higher void ratios. Thereafter, compressibility and hydraulic conductivity is governed by effective stress.

Aug 1, 2010

By W. G. Miller, J. D. Scott, D. C. Sego

An overall study was conducted to evaluate the properties and processes influencing the rate and magnitude of consolidation for oil sands fine tailings produced using different extraction processes. As part of this overall study, consolidation tests using slurry consolidometers were carried out for caustic and non-caustic fine tailings. The influence of a change in bitumen extraction process (caustic versus non-caustic) on consolidation properties, namely compressibility and hydraulic conductivity, was determined, as was the effect of adding a coagulant (calcium sulphate [CaSO4]) to caustic fine tailings. For fine tailings originating from two different oil sands ores (Ore A and Ore B), results were presented in terms of variation in average void ratio with time (settlement), void ratio with effective stress (compressibility), hydraulic conductivity with void ratio and coefficient of compressibility and hydraulic conductivity with sodium adsorption ratio. Findings indicated that chemical characteristics of fine tailings (water chemistry, degree of dispersion) do not have a significant impact on their compressibility behaviour and have only a small influence at high void ratio (low effective stress). The biggest advantage of non-caustic fine tailings and treating caustic fine tailings with coagulant is an increased initial settlement rate and slightly increased hydraulic conductivity at higher void ratios. Thereafter, compressibility and hydraulic conductivity is governed by effective stress.

Jan 1, 2010

By William H. Pomroy

This report describes Bureau of Mines research that led to the design, prototype fabrication, and successful proof-of-concept testing of an improved stench fire-warning system for underground noncoal mines. Stench systems are the most widely used means of warning driers in underground noncoal mines of fires or other emergencies. A stench system alerts miners that an emergency condition exists by injecting an odorant into the mine air. Although stench warning systems have been used successfully for over 60 yr, present systems suffer several serious shortcomings, including odorant toxicity, unreliability of warnings, widely varying stench concentrations, and others. In 1980, the Bureau began a research program to upgrade the stench warning system. The resultant system overcomes the deficiencies of existing systems by substituting tetrahydrothiophene for the commonly used ethyl mercaptan stench odorant, and through the use of a specially designed stench injector. The improved injector reliably meters stench fluid into either ventilation-air or compressed-air streams at a precisely controlled rate. Prototype hardware has been fabricated and proof-of-concept tested under bath laboratory and in-mine conditions.

Jan 1, 1985

By J. W. Adams

Two different techniques were wed to make measurements of the absolute value of electromagnetic noise in an operating hardrock mine, Grace Mine, located near Morgantown, Pennsylvania. Diesel-powered haulage equipment is used in this mine, and the electromagnetic noise environment it creates was measured to see how it differs from the environment created by electric-powered haulage equipment. One technique measures noise over the entire electromagnetic spectrum of interest for brief time periods. Data are recorded using broadband analog magnetic tape and are later transformed to give spectral plots. The other technique records noise amplitudes at several discrete frequencies for a sufficient amount of time to provide amplitude probability distributions. The specific measured results are given in a number of spectral plots and in amplitude probability distribution plots.

Jan 1, 1974

"The characterisation of resources and description of variability across different ore domains is key to accurate prediction of probable metallurgical performance. Such characterisation testwork often has limited drill-core from which to work and this immediately confines the characterisation method to smallscale. For flotation feeds, the JKMSI (Mineral Separability Indicator) is being developed as a potential characterisation tool, building on earlier work by Chudacek, (1990), which used shaken test tubes, and was called the EMDEE device. In addition, the consistency of flotation recovery for specified size fractions has shown to be preserved, irrespective of the amount of material in that size fraction obtained by different milling conditions, so that the overall recovery can be estimated from knowing the particle size distribution (McIvor and Finch, 1991; Bazin et al, 1994, Runge, 2007 and Wightman et al, 2010) The JKMSI unit uses less than 10 g of material per test in narrowly sized classes and results to date have demonstrated the value of the test. This paper discusses the potential of the test by demonstrating the link between JKMSI performance and mineralogy of five different ores from Laguna Seca, Escondida Minera Limitada as well as the correlation to plant scale performance obtained in an earlier survey (Coleman et al, 2006). Further work to tie down the proof of representatively of the small sample has been identified and is discussed and included in the paper. INTRODUCTIONSince the uptake of the flotation process at the turn of the twentieth century, small scale, laboratory methods have been sought to characterise flotation response. Although laboratory batch flotation tests are the most widely used method to evaluate reagents, characterise ore variability and obtain suitable model parameters using various scale up factors Runge (2101) other methods using less ore would be useful where ore samples were limited.A method using test tubes for testing ores’s flotation response to reagents was first developed by Ian Walk (Wark & Wark, 1935; Wark; 1938; Sutherland and Wark 1955). In these tests a 50 cc stoppered measuring cylinder served as a means for a qualitative experiment, the aeration being effected through violent shaking by hand. In these experiments about 10 g of mineral was ground by pestle and mortar under water after which the ground material was deslimed and adequately conditioned with the appropriate reagents."

Jan 1, 2013

By Yukihiro Ishihara, Nanase Ogawa, Ming Lei

"Abstract In the Press-in Method, a static jacking force is used to install a prefabricated pile, while a reaction force is gained from previously installed piles. This piling technique has solved problems in urban piling construction such as noise and vibration associated with the piling work, restricted construction conditions due to the existing structures, and so on, since its emergence in 1975. Its applicability to hard ground conditions has been improved, with the development of press-in machines that involve augering or rotation. Besides, information such as time, penetration depth, jacking force and rotational (or augering) torque in piling work are automatically obtained. The concept of PPT, Pile Penetration Test, has been developed by the authors, to apply the obtained information to the processes of construction planning or foundation design. This paper highlights the technique to estimate SPT N value from data acquired in standard press-in (press-in without any auxiliary methods), press-in with augering and rotary press-in. The technique will be helpful in assuring the adequate embedment depth, re-selecting the adequate press-in machine or auxiliary method, and re-pricing the project objectively, particularly when a contractor encounters unexpected ground conditions.INTRODUCTIONThe Press-in Method is one of the piling techniques that use a static jacking load to install piles. It mitigates environmental problems of noise and vibration that have been associated with other conventional piling techniques.It is also featured by its spatial efficiency; since a ‘press-in’ piling machine gains a reaction force from the previously installed piles, there is no need of bulky weights that will occupy a large space. This feature is emphasized in the piling system in Figure 1, where a press-in machine and its related devices are all positioned and ‘walk’ on top of the pile wall.Its applicability to hard grounds has significantly been improved, with some newly developed piling machines that involve augering or that install tubular piles with teeth on the base by applying axial load and rotational torque at the same time."

Jan 1, 2014

By Jianbo Hu, Gang Han, Tao Zheng, Junfeng Jiang, Rui Su, Qihua Zhao

The rock quality designation (RQD) is a commonly used index for the classification and evaluation of rock mass quality and is widely adopted in mining and geological engineering. The traditional method of obtaining RQD still requires manual measurement of core length and calculation of RQD, which is inefficient. To address this problem, we propose a framework for drilling core image segmentation and RQD estimation from digital images of cores in core boxes based on the deep learning algorithm. The proposed framework is generated by combining the Mask Region-Based Convolutional Neural Networks (Mask R-CNN) instance segmentation algorithm, the U-Shaped Convolutional Neural Networks (U-Net) semantic segmentation algorithm, and the image processing functions of the Open Source Computer Vision Library (OpenCV). To demonstrate the accuracy of the proposed method, seven boreholes in the Xiushuihe vanadium-titanium magnetite mine, located in the Sichuan Province, China, were used as the case study. According to the comparison of the manual measurements and calculations of the cores taken from seven boreholes used to conduct this study, the framework can record the length of the drill cores and calculate RQD within an average error rate of 3.42%, while it saves about 85% of the working time. The results illustrate that the proposed framework enhances the efficiency of RQD calculation while satisfying the engineering requirements.

Jul 31, 2023

By H. R. Thorpe

A floating gold dredge operating in coarse alluvial gravels of the Grey River on the west coast of the South Island, New Zealand, generated high concentrations of clay and colloidal particles in the dredge pond, which entered the groundwater system. Sampling was carried out at depths down to 20 m and it was found that variation of the length of the flow path occurred because of the movement of the dredge towards the piezometers. The alluvial gravels, the suspended sediments, the groundwater system and the water chemistry were all studied. Sediment concentrations were found to be highly variable with depth, but the relative concentrations in the depth profile were generally consistent as the flow distance shortened. The sediments were extremely fine and travelled further through the gravels than predicted. Comparison of field results with the available theory of deep filtration in clean beds of porous media gives some basis for estimating the behaviour of fine sediments in other alluvial systems

Jun 19, 1905

By H. Y. Sohn

Considering the two most important issues the ironmaking industry faces today, i.e., energy consumption and greenhouse gas emissions, it would be advantageous to utilize the concentrate-size raw materials directly without pelletizing or sintering, especially without the use of coke. This plenary lecture describes two such processes developed at the University of Utah. One is the Flash Ironmaking Technology (FIT) and the other is a moving-bed process for continuous ironmaking with gaseous reduction of iron ore concentrate (MBIT). These technologies are designed to produce iron directly from iron concentrate without requiring pelletization/sintering and cokemaking in two significantly different temperature ranges. They take advantage of the high reactivity of the concentrate particles and will considerably reduce energy consumption and carbon dioxide emissions compared with the current processes. The process of the development from the conception of the idea, to kinetic feasibility establishment, to laboratory flash furnace, and finally to the operation of a prototype facility for the development of the FIT is discussed. The development of the MBIT also started with the formulation of the process concept, followed by kinetics feasibility establishment, and the design of a potential industrial reactor. The results of economic analyses on the FIT are briefly described.

May 12, 2023

By F. E. Joyce

The Bureau of Mines studied copper-nickel minerals (mainly sulfides) of the Duluth Gabbro Complex in north-eastern Minnesota to determine their response to selective high-temperature sulfatization techniques. The gabbro, containing 0.44 percent copper and 0.13 percent nickel, was ground to minus 325 mesh and sulfatized in a heated, rotating, stainless steel bench-scale retort. Tests demonstrated that over 95 percent of the copper and 80 percent of the nickel can be converted to water-soluble sulfates, depending upon the roasting conditions employed. Yield equations were developed using regression analysis for predicting the extraction of copper and nickel between the temperature limits of 520° to 670° C, the roasting time limits of 3 to 7 hours, and S02 limits of 10 to 40 percent in S02-air mixtures.

Jan 1, 1971

This paper gives an overview of the difficulties associated with determining the strength of hard rock pillars. Although a number of pillar design tools are available, pillar collapses still occur. Recent examples of large scale pillar collapses in South Africa were caused by weak partings which traversed the pillars. Currently two different methods to determine the strength of pillars are used namely, empirical equations derived from the back analyses of failed and stable cases and numerical modelling tools with an appropriate failure criteria. Both techniques have their limitations and additional work is required to obtain a better understanding of pillar strength. Empirical methods are popular and easy to use, but care should be exercise that the results are not extrapolated beyond the range of the data which were used to derive them. An example is the Hedley and Grant formula (derived for the Canadian uranium mines) that has been used for many years in the South African platinum and chrome mines (albeit with some adaptation of the K-value) to design the pillar layouts. Very few collapses have nevertheless been reported and it might even be too conservative an assumption of pillar strength in these mines. As an alternative, some engineers strongly advocate the use of numerical techniques to determine pillar strength. A close examination unfortunately reveals that these techniques also rely on many flawed assumptions. An area where numerical modelling is invaluable, however, is to study specific pillar failure mechanisms, such as the influence of weak partings on pillar strength. In conclusion, it appears that neither empirical techniques nor numerical modelling currently provide a solid basis to conduct pillar design. It is therefore recommended that both these techniques be utilised when confronted with a pillar design to obtain the best possible insight into the problem.

Nov 25, 2010

By Dr. Daniel W. H. Su

t is both an honor and privilege for me to nominate Dr. Daniel W. H. Su for the inaugural Syd S. Peng Ground Control in Mining Award. I can think of no better candidate than Daniel that is deserving of this award ? an award to recognize technical excellence in advancing ground control technologies [and] approaches. Daniel?s education and career spans over three decades. Having graduated from National Cheng Kung University in Taiwan in 1972 with a B.S. degree in Mining and Petroleum Engineering, he spent the next four years in the Taiwanese military and mining industry, before moving to the United States, where he enrolled in West Virginia University?s Mining Engineering Department. He received his M.S degree in Mining Engineering from WVU in 1978; then in 1982 became the first person to ever receive a Ph.D. in Mining from WVU. His thesis was titled, ?Development of Ultrasonic Techniques for the Measurement of In Situ Stresses?.

Jan 1, 2006