Search Documents

By Haruka Takeura, Tomoaki Murata, Kazunari Yoshida, Masato Adachi

"Pure magnesium is a material with high functionality, however, the cold drawing of this material is very difficult, that is why, until this day there are no optimal cold drawing conditions. Furthermore, cold drawing of pure magnesium wire shows a problem with internal defects that occurs under certain conditions. In this research, the aim is the suppression of internal defects, and final target is to create the optimal cold drawing conditions for pure magnesium wires. The first step is the investigation of the drawing limit by using 250°Cannealed wire. As a result, reduction of 10% per pass was chosen for stable wire drawing. However, in this case, it was found that internal defects occurred at total reduction of over 45% during drawing. Investigation of intermediate annealing conditions that can suppress internal defects, and influence on internal defect that the die half angle and reduction per pass. As a result, it was found that the drawing condition capable of suppressing internal defects most efficiently was 13% reduction drawing by using under 6°half angle die. Consequently, it’s possible to manufacture a cold fine drawn pure magnesium wire of 100µm, without defects in the center of the wire and hindering its mechanical properties.INTRODUCTIONMagnesium is a light and high functionality material that has high vibration absorbency, heat dissipation, electromagnetic wave-shielding and recycling efficiency (Conruy, 1989). However, proper cold wire drawing conditions haven’t been established, that is why warm or hot processing is commonly used (Oishi, Mori, &Kawabe, 2005). As a result, strength improvement of the wires is not possible, that is why the production of medical tools is disregarded. If it was possible to cold draw magnesium wires, the applications for material products would expand. Further, in wire drawing such difficult processing material, if appropriate processing conditions are not selected, defects will be generated inside the drawn wire."

Jan 1, 2017

By A. D. Pienaar

The aqueous chemistry of niobium and tantalum compounds with hydrofluoric acid is a mature field of investigation. In contrast, very little attention has been paid to reactions of these compounds in non-aqueous environments. Similarly, reactions of elemental fluorine with niobium and tantalum compounds have received little more than cursory attention in literature. This work discusses the isothermal reaction kinetics derived from thermogravimetry, using a less redundant approach than is currently the standard. We also discuss the most likely kinetic models for this reaction.

Jan 1, 2012

By Kausik M. Sinha

Hydraulic stowing, which is being practiced in several major coal producing countries to deal with adverse mining conditions, usually permits almost 100% coal recovery from underground mines with minimal and controlled surface subsidence. It can be implemented in the US coal mines to reduce the severe effect of land subsidence and at the same time improve the cost of coal production, both of which are major setbacks for the coal industry in the USA

Jan 1, 1989

By W. Vorster

Bateman Engineering Project's acid-plant track record goes back to 1977. Bateman Engineering can design sulphuric plants based on gas from sulphur burners, metallurgical off gas as well as pyrite roasting systems. Bateman Engineering has a technology marketing agreement with NORAM Engineering Ltd of Canada to provide state-of-the-art, well-proven acid plant technology, and also has access to roaster technology from several sources, including Chinese technology. Utilising the Noram technology agreement, Bateman was awarded the Engineering and Procurement (EP) contract for the Ambatovy Nickel Project, Sulphuric Acid Facilities in 2007. This is the first Greenfield sulphuric acid plant Bateman has designed for many years, producing a combined 5,500tpd, and is one of the largest sulphur burning acid plants in the world. This paper gives an overview of the sulphuric acid plant for the Ambatovy Nickel Project, advantages of Noram?s unique technology on offer, an overview of work conducted on a recent study of an pyrite roasting acid plants as well as a new technology currently being developed by Bateman for the direct combustion of solid sulphur to form sulphur dioxide.

Jan 1, 2009

By R. J. Campbell

[The steady increase of aluminum production means a corresponding increase of carbon consumption in the alumina-reduction cells. Improved petroleum techniques constantly reduce the amount of byproduct petroleum-coke production. These, trends threaten the alumina-reduction works with possible shortages of carbon, which must be supplied from some other source. In anticipation of this shortages, an investigation into the possibility of using coal as an alternative source of carbon was begun at the Northwest Experiment Station of the Federal Bureau of Mines. The investigation lit has developed bench-scale methods that produce carbon of higher purity than is required by specifications for anode carbon. Additional work will b required to bring these processes to pilot-plant seals and to prove the suitability of the carbons, produced or aluminum-anode consumption.]

Jan 1, 1956

By M. Kuchta, A. Newman

LKAB’s Kiruna Mine, located in northern Sweden, produces about 24 Mton of iron ore yearly using sublevel caving. For efficiency, the mine must deliver planned quantities of three ore products. We use mixed integer programming to schedule Kiruna’s operations, specifically, which production blocks should be mined, and when they should be mined to minimize deviations from planned production quantities while adhering to mining restrictions (e.g., sequencing). A new production block database and a well-formulated mixed integer programming model dramatically reduce the size of the original problem; in less than ten minutes we generate five-year schedules with time fidelity of months.

Jan 1, 2002

By W. Vorster

Bateman Engineering Project's acid-plant track record goes back to 1977. Bateman Engineering can design sulphuric plants based on gas from sulphur burners, metallurgical off gas as well as pyrite roasting systems. Bateman Engineering has a technology marketing agreement with NORAM Engineering Ltd of Canada to provide state-of-the-art, well-proven acid plant technology, and also has access to roaster technology from several sources, including Chinese technology. Utilising the Noram technology agreement, Bateman was awarded the Engineering and Procurement (EP) contract for the Ambatovy Nickel Project, Sulphuric Acid Facilities in 2007. This is the first Greenfield sulphuric acid plant Bateman has designed for many years, producing a combined 5,500tpd, and is one of the largest sulphur burning acid plants in the world. This paper gives an overview of the sulphuric acid plant for the Ambatovy Nickel Project, advantages of Noram?s unique technology on offer, an overview of work conducted on a recent study of an pyrite roasting acid plants as well as a new technology currently being developed by Bateman for the direct combustion of solid sulphur to form sulphur dioxide.

Jan 1, 2009

By Pedro Lilienfeld

This report describes a program whose objective was to develop, design, fabricate and laboratory-test two prototype instruments capable of real-time selective detection and measurement of airborne fibrous-shaped particles. The operation of this fibrous aerosol monitor (FAM) is based on the rotation imparted to the acicular particles by means of a rotating quadrupole electric field of the order of 3000 V/cm. This field induces a dipole charge separation on the fibers and aligns them with the applied field. The selective detection of the fibers is effected by synchronous detection of the resulting modulation of the light scattered from a continuous-wave helium-neon laser beam by the rotating particles. The theory of operation, design of the electric-optical detection configuration and the electronic signal processing method are discussed. By means of a scattering pulse sharpness discrimination technique, fibers whose length exceed a selectable value are detected and their number concentration digitally displayed. Counting times of 1 to 1000 minutes permit the measurement of fiber concentrations between 0.001 and about 30 cm-3. A concentration of the order of one fiber per cubic centimeter can be assessed within a relative standard deviation of 10 percent with a counting period of 10 minutes. The FAM is a portable, battery-powered instrument capable of operating continuously for about 4 hours between battery charges. Preliminary tests with crocidolite and crysotile asbestos as well as with glass fibers were performed in the laboratory and the results indicate good correlation with the standard NIOSH phase contrast microscopy filter counting method.

Jan 1, 1977

By Tom Gabardi, Peter Clarke

"MillMapperTM is a new 3D laser scanning technology that has only recently been introduced into the North American mining industry. It enables mill operators to gain a much more complete understanding of the condition of their mill internals and to more accurately predict how liners will perform in the future. This paper describes the technology and techniques used to obtain data on internal mill conditions, how this data is processed into meaningful information which enables better prediction of liner life and gives examples of the reports provided by the software. Examples are given, using client sites data, on how this information is being used to reduce the costs and improve the revenue from SAG and ball mills.INTRODUCTION Scanalyse Pty Ltd developed the MillMapperTM technology in Australia over a number of years and has recently introduced it into North America with a significant take-up in Canada. The technology was commercially released in Australia in late 2006 and there has been significant technical development in the features provided since that time. MillMapperTM has been accepted as a useful technology in the Australasian region and more recently has been introduced to sites in Chile, Peru, Brazil, USA, Canada, Laos and South Africa. Over 100 different mills have been scanned and the technology has been thoroughly tested and validated. It has become an integral tool in condition monitoring and improvement programs for SAG and Ball mills across many sites and is now providing significant and measurable benefits to the mining industry. Some of these benefits will be described in this paper using actual examples."

Jan 1, 2012

By R. H. Sprute

This report describes Bureau of Mines laboratory test results in electrokinetic dewatering and consolidation of metal-mine tailings. Tailings were placed in 0.3-cubic-foot Plexiglass models, and dc potential was applied until dewatering ceased. Time-oriented measurements of water removal, changes in resistivity, and power consumption were recorded during the dewatering process. Dewatered material was tested for moisture content and density. Equipment and procedures were developed to optimize the method for unclassified mill tailings from a particular mine in the Coeur d'Alene, Idaho, district. Results indicate the method to be highly effective in dewatering and consolidating this material.

Jan 1, 1974

By R. G. Hamm

A brief outline covering the shovels and draglines in use in the open-pit mines of Western Canada, including British Columbia, Alberta and the Yukon, is given, followed by the procedure for the selection of the correct wire rope for each application. Such fa ctors as wire rope constructions, lay directions and types of cores are mentioned. Once the correct wire rope has been selected, there are variousfactors that can affect the service fife ofthe rope and the reduction ofdown-time during rope change-overs. Factors such as hairpin winding, types of Becket loops, and shovel drum and bail adaptors are described.

Jan 1, 1979

By D. H. Desy

The Bureau of Mines has conducted research on the ignition of methane-air mixtures by sparks caused by frictional impact of aluminum alloys on rusted steel at typical coal mine fan speeds. The objectives were to establish the incendivity of aluminum alloys under these conditions, to investigate differences between aluminum alloys, and to evaluate substitute materials for the aluminum-steel combination. With a specially designed apparatus, three commercial aluminum casting alloys and a number of experimental aluminum alloys were tested for incendivity of the frictional impact against rusted steel in flammable methane-air mixtures. All aluminum alloys tested produced some ignitions. Of the experimental alloys, the harder alloys and those containing silicon tended to be more incendive than the others. With the normal experimental conditions, constructional steel, stainless steel, brass, and plastic did not cause ignition of methane-air mixtures in frictional impact against rusted steel. Some ignitions occurred with constructional steel at high speed in more flammable gas mixtures enriched with oxygen. From these findings, it is suggested that constructional material combinations other than the aluminum-steel combustion would minimize this inc endive hazard. A detailed description is given of previous research, and comparison is made with present results where appropriate.

Jan 1, 1975

By D. Olsen, S. Cole, J. Strid, G. Colzani

This paper focuses on the underground tunnel work at the Hollywood Water Quality Improvement Project (HWQIP) in Los Angeles, CA. The HWQIP is being constructed to provide a water distribution system to bypass the existing Hollywood Reservoir System, which supplies drinking water for 500,000 people. The major project features include, a 2.9-meter diameter 1,829 meter long bypass tunnel, a 1.8-meterdiameter 366 meter long utility tunnel, 3 jack and bore tunnels, two 136 million liters underground circumferentially wrapped pre-stressed concrete water storage tanks, associated piping, and mechanical facilities. The physical project location coupled with strong community involvement and stringent environmental concerns was a considerable driving force for this project located in the Cahuenga Pass area of the Hollywood Hills north of Los Angeles, CA.

Jan 1, 2001

By W. I. Nissen

As part of its program to provide technology for reducing undesirable environmental impacts of mineral processing operations, the Bureau of Mines developed the citrate process for desulfurizing industrial stack gases that contain from 0.1 to 2 vol pet S02. In this regenerable flue gas desulfurization (FGD) process, S02 is absorbed from cleaned and cooled industrial flue gas with a citric acid-sodium citrate solution. The absorbed S02 is subsequently reacted with H2S to precipitate marketable elemental sulfur and regenerate the solution for recycle. Laboratory investigations of process parameters provided information for designing larger scale continuous operations. Information gathered from operation of two pilot plants, one at a copper smelter and one at a lead smelter, confirmed the laboratory results. Data were obtained for design and construction of a commercial-sized demonstration plant at the George F. Weaton Power Station, Monaca, PA. A preliminary operation of the plant was demonstrated, under a cost-sharing Bureau-industry contract. This bulletin describes the citrate process and gives results of the laboratory, pilot plant, and demonstration plant studies, as well as corrosion investigations.

Jan 1, 1985

By N. Abdel-Khalek, A. Youssef

The tailings from beneficiation of Florida phosphate ore contain considerable phosphate values. These tailings are currently discharged into large disposal areas. More than three million tons of P2O5 are discarded with the phosphatic slimes (clays) in Florida each year. These phosphatic clays not only create one of the most difficult disposal problems in the mining industry, but also represent a tremendous loss of P2O5. As the quality and quantity of Florida’s phosphate reserves diminish, recovery of phosphate values from these wastes becomes more vital. This will also significantly lengthen the life of these important phosphate resources. Thus, it is the goal of this study is to recover more than 80% of the phosphate values in phosphatic clays. A systematic study to characterize samples taken from inactive disposal area has been conducted. The data suggest that natural segregation takes place in the settling pond. In other words, coarser particles settle closer to the feeding point of the pond. Flotation tests were conducted using the +325 mesh fraction of samples obtained from sites close to the feeding point (sample# A) and further from that point (sample# B) and (sample# C) which is even further away from the feeding point. The results show the following: Sample# A gives the highest grade and recovery, followed by that of # B and then of # C. There is a great potential to upgrade sample# A where concentrates of high grade (68.9-70.1 % BPL or 31.5- 32.1% P2O5) and recovery (~86.6-95.4 %) can be obtained under the investigated operating conditions (1.0 – 2.0 kg/ton sodium silicate and 1.5—3.0 kg/ton collector mixture of fatty acid and fuel oil). The mineralogical and chemical analysis of all samples is presented in this paper for comparison. Only in this paper, the flotation data of (site # A) are discussed below.

Jan 1, 2002

By W. B. Boggs

The Noranda smelter was built by Noranda Mines, Limited, from the designs of A. E. Wheeler, consulting metallurgist, New York, for the reduction of ores and concentrates from the Horne mine, and to treat, on a custom basis, ores and concentrates from other mines in the Rouyn district. The smelter is situated at Noranda in western Quebec, about 330 miles directly north of Toronto. Ground was first broken for construction in November, 1925, before the completion of the branch railway into the district, which was not finished until October, 1926. After many difficulties and delays due to the Jack 'of transportation and the severe weather during the winter months, the smelter was started in December, 1927, and the first blister copper was poured on December 17th. The smelter was built throughout in two duplicate units, each with a rated capacity of 500 tons of ore per day. Operations were started with only one unit, and after several months it was found that one unit alone would smelt 1,000 tons of ore per day. At this time only one shaft, No. 3, existed, and its hoisting capacity and the capacity of the original crushing plant were insufficient to supply ore for two units at the increased tonnage. Accordingly No. 4 shaft was sunk and a new crushing plant provided to handle the ore hoisted there. This work was completed in the latter part of November, 1929, and since that time both smelter units have been operating.

Jan 1, 1930

By Ernest W. Johnson, F. E. Cash

"INTRODUCTION Mine operators have long realized the importance of providing a satisfactory and dependable means of giving prompt warning to underground mine workers at the occurrence of a mine fire or other threatened disaster.Most underground mines of the Lake Superior district are prepared to inject a stench liquid into the compressed-air system quickly to give such warning. The liquid evaporates quickly and gives off an intense and easily recognizable odor even when present in minute quantities in the mine air. Workers in the mines studied have been fairly generally familiarized with the odor and instructed as to evacuation procedure when the warning odor is detected.In some mines provided throughout with electric lighting, including working faces, a prearranged light-flashing signal is given as a warning supplementary to that received from the stench.In a few mines, workers have been instructed to evacuate the mine immediately in the event the compressed-air supply is cut off, regardless of whether mechanical failure may be involved.Information obtained in observing a number of stench-injection tests is compiled and presented in the hope-that it will serve as an incentive to provide means of making stench injections at mines not now so equipped and for making similar tests at other underground mines, so that in case unsatisfactory results are obtained rectifying adjustments or changes may be made in time. It is further hoped that this paper will bring out the real importance of repeating these tests from time to time, at least once a year on each operating shift, so that in the event of an actual emergency, underground employees will receive a prompt warning."

Nov 1, 1945

By Júlia Beltrami

O trabalho estudou a formação, a interação com a escória e a solidificação de inclusões geradas durante o processamento de aços dual-phase com alto teor de silício (>1%). A composição destes aços, se não bem controlada, pode gerar inclusões sólidas de sílica pura durante o lingotamento contínuo. Para o estudo, foram feitas simulações termodinâmicas com o software computacional FactSage 6.4. As simulações mostraram que os fatores mais importantes para a composição inicial das inclusões é a relação %Mn/%Si e o teor de alumínio dissolvido no aço. Ao interagir com a escória, a tendência é que as inclusões se aproximem da sua composição ao longo do tempo. Durante a solidificação, a maioria das inclusões apresentou fases deformáveis e de baixo ponto de fusão, com exceção das inclusões sem CaO e da inclusão com 25% de Al2O3 e teor intermediário de CaO, que apresentaram as fases tridimita, coríndon e gehlenita de alto ponto de fusão e não-deformáveis.

Aug 16, 2017

By G. J. de Korte

South Africa’s best-quality coal, located in the central Highveld basin, is becoming depleted and alternative sources of coal, such as the Waterberg coalfield, will have to be developed to supply the country with coal in the future. The quality of the coal being mined in the central basin is gradually becoming poorer. This necessitates that more of the coal be processed to improve the quality to meet customer requirements. The challenge to the coal processing industry is to process low-yielding coals to produce goodquality products and at the same time ensure that coal mining remains economically viable. This requires that more cost-effective coal processing technologies be investigated and implemented.

Jan 1, 2015

By B. W. Gandrud, A. C. Richardson

"INTRODUCTION The Bankhead mine of the Cane Creek Coal Mining Co. is in the central part of Walker County, Ala., 4 miles south of Jasper. The Mary Lee bed in this part of the State yields a practically free-burning coal which is marketed as a. steam-raising and domestic fuel. As mined, the coal ordinarily contains ash-forming impurities to an extent that makes it necessary to treat the coal by some washing process before it is marketed. At present the Bank-head coal coarser than 3-1/2 inch is hand-picked and the coal finer than 3-1/2 inch is washed in two single-compartment jigsThis paper contains the result of screen-sizing and float-and-sink tests on a representative sample of the run-of-mine coal and the results of tests made to show the amount of coal liberated from impurities by crushing the coarser sizes. .This report is one of a series on the washability of Alabama coals which is being prepared by the U. S. Bureau of Mines and the University of Alabama, with the cooperation of the coal producers of Alabama.SAMPLING AT THE MINE'The Mary Lee bed at Bankhead consists of two benches separated by a rock parting which varies in thickness from place to place in the mine. The top bench has a very uniform thick-nest; throughout the workings and yields about 65.0 per cent of the output. The bottom bench varies greatly in thickness and in nary places becomes too thin to work at a. profit. The sample for the washability study was taken underground at a place which was typical of the mine as a whole. In taking the sample the working face was squared up and a representative section out from each bench. Care was taken to secure a, quantity of coal from each bench proportional to the quantity contributed to the mine output. The rock parting as gobbed in accordance with the usual mining practice. The total sample taken weighed 3 tons."

May 1, 1933