Search Documents

By Naiyi Li, Henry Hu, Alfred Yu

"In the past few years, various squeeze cast aluminum components have been developed and successfully implemented in various vehicles by the automotive industry because of their superior engineering performance. However, fundamental understanding of the formation of air gap during squeeze casting processes is still very limited despite of its significant influence on the extent of heat transfer between the casting and mould. In this paper, a mathematical model has been developed to simulate phenomena of air gap between the casting and mold' during squeeze casting of aluminum alloys. The model considers the effect of process parameters such as applied pressures and mold temperatures on the events of air gap formation. The predication indicates that the occurrence of highly enhanced heat transfer in squeeze casting of aluminum alloys primarily results from the presence of excess applied pressures.IntroductionA number of squeeze cast Al components has been developed and used in mass-produced vehicles in the past few years, such as steering knuckles, Road wheel, Engine Block etc. This is attributed to their superior engineering performance. In squeeze casting, the cooling rate can be increased by applying high pressure during solidification which results in the noted refinement in the micro structure scale leading to better casting properties. However, the excessive pressure increased interfacial heat transfer coefficient is affected during the solidification by air gap formation and die surface condition etc., which is believed to increase thermal resistance at the casting/die interface [l - 4]."

Jan 1, 2004

Stope back conditions in the cut-and-fill stopes at New Broken Hill Consolidated Limited often deteriorate to such an extent that, because conventional rockbolts are not able to maintain safe working conditions, square-set timber is installed. An attempt to eliminate this costly procedure has involved the use of long grouted rockbolts using high tensile prestressing wire. These bolts were developed in conjunction with the prestressing engineers of BBR (Aust.). This form of support has improved the back conditions, maintained safe working conditions, and delayed the introduction of timber in a number of stopes.Production from these stopes has been maintained at its previous level (at a rate approximately double that of a comparable timber stope).

Jan 1, 1974

By Earl C. Hutchison, Wade C. Hutchison

T 0 effectively evaluate property damage that is claimed to have been caused by blasting activities and in order to lay the proper foundation to build the best legal defense, identification of the actual causation for the damages are necessary. For the past twenty years, engineering personnel from VCE, Inc. (previously Vibration Control Engineering, Inc.) have been evaluating claimed blasting damages with pre- and postblast inspections, with analysis of seismic levels, blasting amounts at given distances, and with other engineering considerations. In addition to these evaluations, they have also documented other causes for damages which are of the types that are often claimed as blasting damage.

Jan 1, 1995

By J. J. Shields

This study by the Federal Bureau of Mines concerns different methods of face haulage used with various types of continuous-mining machines, mobile-loading machines, and track-mounted equipment under varying roof and bottom conditions and in coalbeds of varying thicknesses. This report is the ninth in a series on mechanical mining in bituminous coal mines. Reference to the reports previously published is made in appendix III, p. 106. Use of modern mining equipment in bituminous coal mines has resulted in increased productivity at the face. This especially is true where continuous-mining machines are used, and the supervision is good. Previous methods and equipment for moving coal from the face became inadequate and had to be improved to restore balance to the mining systems. Sometimes new equipment was needed to improve the face haulage, and in some instances, a new combination of existing equipment was used. Detailed studies of face haulage methods were made at 13 mines in Pennsylvania, West Virginia, Ohio, and Illinois to compare their effectiveness and to describe fully the conditions under which each method was used.

Jan 1, 1960

By James M. Link

Underground coal mining is the most hazardous industrial occupation in the United States.. Haulage accidents in underground coal mines contribute substantially to the occupational hazards of this type of work. In an effort to improve mine safety, a completely hydraulic transport system has been designed to move coal from the mine face to the preparation plant. The capital investment for the hydraulic haulage system is great, and the size of the mine developed for this study is large. Mine production for the conventional haulage mine is 1. 1 million tons of clean coal per year, while the hydraulic haulage mine will produce over 1.6 million tons of clean coal per year. Safety statistics for a number of mines of this size are shown.

Jan 1, 1975

By Charles L. Kimbell

The year 1979 was a period of increased activity for the world's mineral industry, distinctly in contrast with 1978 when estimated world crude mineral output value declined slightly and most phases of the industry's activity were somewhat curtailed. In 1979, most major mineral commodities recorded significant gains in output, with a substantial number achieving new record highs; details on trade levels for 1979 were not available, but increases over those of 1978 were expected on the basis of partial data. Consumption of most commodities edged higher; in some cases the higher demand levels were met largely through draw-downs of stocks accumulated in recent years, while in other cases notable output increases were required to meet demand. Actually, 1978 was not a bad year for all elements of the mineral industry if changes in output levels of the various commodities are considered as a measure of performance. There were far more individual commodities registering production increases between 1977 and 1978 than registered declines, but some of those reported as declining were relatively major commodities (bauxite, aluminum, copper and zinc were notable), Moreover, the upturn in productive activity in 1978 was not matched by increases in profits. However, 1979 was unquestionably a year of renewed expansion efforts, although some commodity areas, most notably the steel industry component, were still experiencing difficulties.

Jan 1, 1981

By T. K. Bundtzen

Placer gold in the Iditarod and Innoko mining camps of western Alaska is derived from a suite of comagmatic, Late Cretaceous to Early Tertiary, alkali-calcic, meta-aluminous. volcanic-plutonic complexes and peralumi-nous rhyolite sills that intrude Mesozoic flysch. Heavy-mineral concentrates from 42 mining operations and streams draining known mineralized areas in the igneous complexes contain placer gold and a variety of ore minerals derived from epithermal to hypothermal conditions of formation. The minerals include cassiterite, ilmenorutile, samarskite, cinnabar, scheelite, chromite, stibnite, silver sulfosalts, monazite, and zircon. Results of the study show that 1) cinnabar. stibnite, and quartz formed with the bulk of the placer gold in an epithermal lode environment, 2) chromite appears to have originated in mafic phases of monzonite plutons and alkalic basalts, and 3) niobium-tin-tungsten-uranium-silver values may have been derived from stockwork accumulations in cupolas of monzonite plutons.

Jan 1, 1987

CONTENTSThe significance of values givenINTRODUCTIONTHE ORE1. DATA SECURED FROM THE MILLING PLANT AS OPERATING BETWEEN 1938 AND 1942(a) Mill Recoveries(b) Mill Flow Sheet(c) Scheelite-Garnet Association(d) Detailed Examination of Mill Performance during 1942Crushing UnitsCoarse Rolls DischargeFine Rolls DischargeFeed to Huntington MillsFinal Ground ProductProduction of -200-mesh Scheelite SlimeSummary of Information on Crushing and Grinding Circuit(e) Detailed Examination of Mill Performance During 1942Concentrating UnitsLocation and Nature of Scheelite LossesSize Distribution of Scheelite LossesDistributor Spigot ProductsSummary of Information on Concentration Circuit(f) Detailed Examination of Mill Performance During 1942 Gravity Plant Feed2. EXAMINATION OF MINE SAMPLES TAKEN DURING 1942(a) Introduction(b) Nature of the Ore(c) Sampling of Mill Feed(d) Testing Technique(e) Minus 1/8-inch Ores-Naturally Broken Fractions(f) Recoveries from Plus 1/8-inch Fractions-Crushed to Minus 1/8-lnch(g) Probable Recoveries Obtainable from Weathered Ores140 Contour120 Contour90 Contour(h) Examination of an Ore Sample from the 90-foot Adit(i) Run-of-Mine Ore(j) Evidence of Maximum Sizes of Scheelfte Present in Run-of- Mine Ore(k) Summary of Information on Liberation and Recovery from the Ores as Mined in 1942 and from the Mill Samples

Jan 1, 1944

By R. E. Heithecker

The Zwolle oil field of Sabine Parish, La., is different from most oil producing areas of the State in that the oil is obtained from marl and chalkrock formations. The thickness of the reservoir rocks averages 500 feet; but production is not continuous throughout this thickness, as the oil apparently is localized in vertical and nearly vertical solution cavities and channelways or in porous zones of limited horizontal extent. The nature of the oil accumulation has caused two outstanding peculiarities of the field: (1) About 60 percent of the tests drilled were dry holes and (2) there were many instances of well interference. Commercial production was discovered in November 1928, after 17 years of prospecting in and around the present limits of the area now developed which has a length of about 22 miles and a maximum width of 4 miles. The field had produced 10,266,896 barrels of oil to January 1, 1934. The oil ranges in gravity from 400 to 420 A.P.I.

Jan 1, 1934

By S. J. Broderick

[Xuge d-mp heap co:lt:.ini9: tilcu?:na3s of tons of cad ~eP~se 2r3 a failiar sight in coal-mininc regior@:. T5ey reprecei~t considergole economic 1083, are very l.u.,si~hC,ly, ?:ld t?ke un m-lch vaL-x3le qace. Cor.sequentl;r thelr remcval i~ geatlyr dezir36, ax2 my ret-sn t?-at c,m be obtained would be er;pecic.llj .a~elconre&apos; t.7 the cod ir.S..r; kry. T?.e vaste rk.t~ri..tl conpl-ises large pieces of slr.t.e, hi~h-2s&apos;. bore c~al., luqs cf cle:., ,ad finer refuse conin,= fro3 the vrtskery, Tilt 1:zshcr:r refilsn contnins sone yood coal. Rig coal and the &apos;better p~lcs of bore ere the zat~rla2.s ~15:;~itiered in this in- vest ig:?.tion. 7% Il~avter frnctions of the w~~sherjr ref;lw aizd tts large 2ieces of slcte ?,".:I rgck contilin 1it:lei ccai-i-bcna.c~o~s caterial ad are vir- tu<dly worthiess nc, rz:. ::atcrin!. for .*=irin,= zct,iv?*teb cCvb~n. 13 the 3irniingh.m district, i13br.12, a-c.ju",P p?rcccn",f the c3sl r?.ir?ed is washed, ,md in tkis c?i.;trict nlz:~c rcfilce ecc;:?:lletcs ~t the r%tg of 1 to 2 million .! tons 2 yew.]

Jan 1, 1941

A Novel Diagnosis and Evaluation Procedure for Flotation Plants

Sep 13, 2010

By C. H. Riggs

THIS REPORT give&apos;s the results of a study of the central and south parts of the Cushing oilfield, including a description of the geology, a review of the production history, and estimates of oil reserves available by secondary-recovery methods. Each of the major producing zones of the field is treated separately. The report, which is one of a long series of field studies the Bureau of Mines has conducted over the past 40 years, was prepared to aid operators to increase oil recovery and to help prevent underground waste in the Cushing field, in the State of Oklahoma, and in the United States. The geology and production history are presented not as a review of past behavior of the Cushing field but rather to interpret the possibilities for increased oil recovery by future development of this and similar areas. The field, which is in the northwest corner of Creek County, Okla., was discovered in 1912 and developed during 1913 and 1914. For several years it, was one of the most important areas producing high-grade crude oil in Oklahoma. Although some oil has been recovered from each of 10 separate reservoirs, nearly 98 percent of the total recovery of oil in the area studied was from 4 major producing formations (table 1). Of these, only the Bartlesville [ ]

Jan 1, 1958

By W. S. Landers

This bulletin is a detailed study of low-temperature, entrained-bed carbonization of a Texas lignite. The lignite studied was from the Sandow strip mine and is representative of the Rockdale formation of the Wilcox formational group. Carbonization was conducted in a continuous entrained-bed reactor at several temperatures in the 8801 to 1,52°C F range, and at air-coal ratios it the 0 to 10.30 scf/lb range (moisture- and ash-free basis). Carbonization rates ranged from 97.1 to 410.0 lb/hr (as-received basis), At the higher air-to-coal ratios employed, all or most of the carbonization heat was provided by internal combustion with air in the reactor. At the lower air-to-coal ratios, parts of the heat for carbonization was supplied externally. It was demonstrated that the entrained-bed carbonization of lignite is a complex reaction and that several variables, of which carbonization temperature, air-to-lignite ratio, and the average size of lignite are important, act together to influence both the carbonization yields and the properties of the resultant products, Process variables established by pant tests were used to design the industrial scale carbonizer operated at Rockdale, Texas, by the Texas Power & Light Company as agents for the Aluminum Company of America. Properties of the carbonization product obtained from the industrial scale reactor were essentially the same as those obtained from the pilot plant reactor operated under the same conditions.

Jan 1, 1968

Recommendations from 44 mining industry workshops are summarized and reviewed in the context of Bureau of Mines research and development programs on-going during the period 1974-1977. Approximately 1,000 specific recommendations for research and development are summarized in a systematic and comprehensive format appropriate for review by mining research and development program managers. Relevant Bureau of Mines research programs are briefly described and some opportunities for future research and development are identified.

Jan 1, 1979

By Bin Tang, Suping Yao

In the last decade, the copper industry in China has developed rapidly and attracted the world’s attention. The production capacity of refined copper has grown remarkably from 4.578 million tons in 2010 up to 9.029 million tons in 2018, accounting for about 40% of the global refined copper production. And now, China has become the biggest refined copper producer in the world. This paper summarizes the application of modern copper metallurgical technologies such as Outotec flash smelting/converting technology, Cyclone smelting technology, TSL (ISA/Ausmelt) smelting/converting technology, Jinfeng side blown smelting and Baiyin side blown smelting technology, Chifeng side blown smelting and continuous top blown converting technology, SKS bottom blowing technology, Dongying two-step smelting technology, copper electrorefining with high current density, etc. in China’s copper industry, analyzes and compares the characteristics of those technologies and presents the great efforts of China’s copper smelters in adapting to the increasingly strict emission standards and improving economic benefits of copper smelters. INTRODUCTION China has been the biggest refined copper producer in the world for many years. China produced million tons of refined copper in 2018, accounting for 40% of the copper smelting production in the world, and of which, roughly, 70% of the copper concentrate was imported, mainly from Chile, Peru and Australia. ICSG (International Copper Study Group, 2017) shows clearly the position of top 20 countries of copper production and copper mine production (Figures 1 and 2). Blast Furnaces, Reverb Furnaces and Electric Furnaces dominated China Copper Smelting for quite long time till 1980s. The first modern copper smelting technology (flash copper smelting) was introduced into China in 1980s, then followed by Noranda, Ausmelt and ISA. Since then, China copper smelting technology stepped into modern time. Since 2000, old processes (Blast Furnace, Reverb Furnaces and Electric Furnaces) were phased out and replaced by modern smelting technologies. China Copper Production has been increasing dramatically (Figure 3).

Jan 1, 2019

By Jacob Chacko

The Izmit Bay bridge, a 3-km-long suspension bridge crossing of Izmit Bay, Turkey is planned to be constructed in one of the most seismically active places in the world. The site, which has the potential to experience significant earthquakes associated with the relative motion accommodated on the North Anatolian Fault, is underlain by deep deposits of soft soils, and areas of unstable and liquefiable soils. Characterizing the seismotectonic setting, foundation soil conditions, potential fault locations, as well as other geohazards was a critical component for the project concessionaire to finance the project and obtain meaningful bids for bridge design and construction. Given the Build Operate Transfer (BOT) funding mechanism, executing this work in the least possible time was critical to the concessionaire?s financing scheme. Fugro was retained to provide geotechnical, geological, and seismological evaluations for the project region, and to generate data for contractors to develop reliable designs and bids. The uncertainties in these data made it difficult for the BOT concessionaire to finance the project and tender Bridge design and construction. The investment in an early and comprehensive site characterization program to evaluate and quantify those uncertainties allowed the concessionaire to save schedule, provide a robust bid basis to bridge contractors, and persuade banks to finance what was perceived to be a relatively high risk project.

Jan 1, 2011

By Mervin D. Marshall

A quick-reaction, mine permissible rescue vehicle (MERV) was developed for use by rescue teams. The MERV is a 6-wheeled, battery-powered unit with life support equipment and instrumentation; designed for a two-man team, with provisions for handling two victims or tools in a trailer. The vehicle is 100 inches long, 56 inches wide, and maximum height of 34 inches. It can be lowered down most mine shafts and has clearance to travel mine railways. The vehicle has power to all six wheels with power transmitted separately to either or both sets of wheels. Low-pressure, high-traction tires give the vehicle the ability to handle soft, muddy mine floors, flooded areas and significant obstacles, and can negotiate a 45% grade. Power and life support are sufficient for a 4-hour mission. The life support system is a commercially-available, approved unit currently used by MESA rescue personnel. A payout wire system provides communication between the vehicle and home base over a distance of 10,000 feet. On-board monitoring of carbon monoxide, methane and oxygen is provided, with master and individual alarms to warn of gas concentrations outside pre-set limits. A lightweight, water-tight trailer was developed for carrying victims or hauling tools and equipment.

Jan 1, 1979

By D Beahm

Introduction The Energy Metals Corporation (EMC) holds numerous mineral properties in the northern portion of the Great Divide Basin including the JAB Property, one of several potential properties being planned for development as a satellite facility to the greater Antelope Uranium Project. A National Instrument 43-101 Technical Report has been completed for the JAB property. This report estimates total measured and indicated mineral resources on the property totaling 3,555,022 pounds U3O8 contained in 2,400,875 tons at an average grade of 0.073 % U3O8 at a .25 GT cutoff in accordance with CIM Standards on Mineral Resources and Reserves. The JAB Property is located in Sections 13, 14, 15, 16, 21, 22, and 23, Township 26 North, Range 94 West, approximately Latitude 42o 14’ North and Longitude 108o 00’ West (Figure 1, Location Map). This property consists of unpatented mining lode claims and Wyoming State mineral leases comprising approximately 2,100 acres.

Jan 1, 2007

By W. E. Tournay

In accordance with a cooperative agreement between the Bureau of Mines, United States Department of the Interior, and the Linde Air Products Co., an investigation was made at the Bureau Explosives Testing Station, Bruceton, Pa., to develop suitable test methods for evaluating the performance and sensitivity characteristics of liquid-oxygen explosives. This report presents the results of the investigation. The unique nature of liquid-oxygen explosives necessitated both modification of standard techniques and development of entirely new test methods. The latter requirement was due to the fact that differences exist in the kind of information that must be developed for studying relative safety and performance properties of these explosives compared to that of fixed explosives.

Jan 1, 1949

By Scott Rosenthal, David Gilkey, Michael McGivern, Lorri Birkenbuel, Daniel Autenrieth, Ty Murphy, Hadi Aldossari

A safety climate case study was carried out at a surface metal mine where investigators administered the Liberty Mutual Short Scale Safety Climate Survey to 365–368 miners to measure safety climate in consecutive years. Following the baseline safety climate survey in 2019, Foundations for Safety Leadership (FSL) training was conducted with 81 middle to upper management employees at the mine site. Investigators found statistically significant differences in the pre vs. posttraining FSL assessment scores of the middle to upper management employees who attended the training. The follow-up safety climate evaluation was compared to baseline scores and revealed no significant improvement. The overall baseline company safety climate score of 76.38 increased minimally to 76.50 (p-value = 0.616). Investigators also evaluated differences in safety climate between the company’s three major divisions (operations, maintenance, and administration). Both years administration had the highest mean score and operations had the lowest mean score. The authors attributed the statistically significant differences found among the three major divisions to various dissimilarities in their work environments.

Aug 13, 2021