Search Documents

By R. J. Visintainer, W. L. Whitlock

"Difficulties with the sizing and operation of centrifugal froth pumps are common and the underlying fluid dynamics are complex. Design and selection often relies on previous experience, offering unreliable guidance for novel applications or unexpected problems. The current paper describes a program of extensive laboratory testing on froth handling centrifugal pumps, covering a range of flows, heads, speeds, viscosity, air content and froth stability. Variations in impeller vane design and the effectiveness of an airlock venting apparatus were also examined. The program resulted in a better understanding of centrifugal froth pump dynamics and insight for the troubleshooting of field applications.INTRODUCTION The Challenge of Pumping Froth In pumping mineral processing froth, the handling of large quantities of air within the fluid is often unavoidable. Efforts to reduce the amount of air present at the pump suction, while always recommended for improving pump performance, may have limitations. Some strategies may also carry an economic penalty, such as unwanted process dilution (e.g. due to water spray or injection), or increased capital cost of equipment due to oversized pumps, sumps and/or piping. Froth pumping losses fall into several categories, as described below and represented graphically in Figure 1. • Density effects: Entrained air reduces the pressure created by the centrifugal pump in direct proportion to the reduction in bulk density. This is not a true “loss”, since the head produced by the pump (in meters of froth), may remain unaffected. However, the reduction in pressure often leads to a corresponding increase in pump speed required to drive the system, which itself leads to increased NPSH required by the pump (NPSHR). Furthermore, by adding a gas phase, the overall volumetric flowrate is increased, assuming a fixed quantity of de-aerated liquid being handled. This leads to increased suction velocity which further reduces the NPSH margin by simultaneously increasing pump NPSHR and decreasing system NPSH available at the pump suction (NPSHA). • Viscosity effects: Increased viscosity introduces an additional factor in some froth pumping applications, such as oil sands bitumen froth. Losses result from increased shear stress within the fluid flow, which increase with flowrate. Viscosity also facilitates the formation of airlock by reducing turbulence and allowing individual bubbles to coalesce more easily within the flow stream. Finally, it increases pump NPSHR by increasing local pressure drop in the vicinity of the vane inlet edges. • Airlock effects: Also known as air binding, it occurs when air or gas coalesces within the pump suction or impeller passages and begins to collect there, held by buoyancy forces within the rotating flow field. In essence, the liquid “floats upwards” towards the pump suction against the outward directed centrifugal forces. The airlock acts as a blockage, with corresponding reductions in flow, head and efficiency. NPSHR also increases, due to increased velocity and distorted streamlines in the flow circumventing the blockage."

Jan 1, 2012

These proceedings consist of papers presented at two Bureau of Mines Technology Transfer Seminars for the purpose of disseminating recent advances in mining technology related to coal mine fire and explosion prevention. Primary, although not exclusive, emphasis is placed on underground coal mining. The papers address research accomplishments ranging from methods for detecting mine fires to remote sealing systems for extinguishing coal mine fires. Each paper represents the current state-of-the-art in the respective research categories. Presentations include research occurring from both Bureau in-house and contract efforts.

Jan 1, 1978

By Etienne Audibert

No satisfactory theory has yet been advanced to explain what takes place when an explosive is fired in a mixture of firedamp and air. The only means of measuring the' danger is to fire the explosive into the gas mixture and note the effect, but the conditions of firing must be chosen carefully. This report is presented in the hope that it will assist in determining what method to use. The experiments have been designed to show the effect of the principal factors involved in the conditions of firing, and the results give information that seems to have some value.

Jan 1, 1940

By Etienne Audibert

No satisfactory theory has yet been advanced to explain what takes place when an explosive is fired in a mixture of firedamp and air. The only means of measuring the danger is to fire the explosive into the gas mixture and note the effect, but the conditions of firing must be chosen carefully. This report is presented in the hope that it will assist in determining what method to use. The experiments have been designed to show the effect of the principal factors involved in the conditions of firing, and the results give information that seems to have some value.

Jan 1, 1940

By Y. C. Kim, M Nataraja, J. T. Buckley, D. H. Tiktinsk

The Nuclear Waste Policy Act of 1982 (NWPA) assigns the U.S. Department of Energy (DOE) the responsibi1it.y of locating, constructing. operating, closing and decommissioning a nuclear waste repository. Prior to submittal of a licensee application to the U. S. Nuclear Regulatory Commission, the DOE is required by 10 CFR part 60 to conduct a program of site characterization for the site to be described in such application. Site characterization includes an exploration and research program in the field and laboratory to determine the geologic conditions and ranges of those parameters which are necessary for determining the suitabi1it.y of the site as a geologic repository. The information thus collected should be able to establish with reasonable assurance that the public and environment will be adequately protected from the hazards associated with a repository at the site. This paper demonstrates by example a geostatistical approach which, on the basis of the existing limited data base, can be used to evaluate (1) whether existing information on a certain parameter is adequate to be considered representative. (2) if additional information is required, where should the additional sampling or testing be performed, and (3) whether the new1.y acquired data along with the existing information constitute representative data.

Jan 1, 1986

By George H. Holmes

This paper is one of a series on mining methods and practices published by the Bureau of Mines. It describes quarrying methods and crushing practices of the U. S. Lime. Products Corp. at its Sloan and Apex quarries. Calcining and milling processes. at the Sloan and Henderson plants also are outlined. The Sloan dolomite and limestone quarries and plant are in secs. 12 and 13, T. 23 5., R. 60 E., and sec. 18, T. 23 S., R. 61 E., M.D.B. &M., Clark County, Nev., about. 17 miles by paved highway southwest of Las Vegas (fig. 1). The Apox limestone quarry, and crushing plant are in sec. 26, T. 18 S., R. 63 E., M.D.B.&M., Clark County, Nov., approximately 18 milos northeast of Las Vegas, adjacent to U. S. Highway 91 (fig. 1). The Henderson calcining plant is Inc., in sec. 13, T. 22 S., R. 62 E., 14 miles southeast of Las Vegas on U. in a reduction unit of Basic Magnesium, M.D.B. &M., Clark County, Nev., about S. Highway 93 (fig. 1).

Sep 1, 1949

By R. B. Alke

Request to Mine Beneath Bridge The Jabs Run Bridge is a reinforced portland concrete arch filled bridge located on WV Bouts 7 near Pentress, WV. The bridge has a span of 22.9 m (meters) and a height of 4 m above normal pool elevation to the underside of the center of the arch (See Pig 1). The bridge is a two lane structure with a width of 6.86 m. The structure is over 50 years old Wing been built in 1929 and is owned by the Department (WV Department of Highways).

Jan 1, 1984

By A. M. Tunstall, N. Djordjevic, H. A. Villalobos

The damage zone behind a typical smooth-wall blast in the open pit was assessed by visually examining diamond drill core to identify blast-induced cracking, mapping core rock quality designations to identify changes in fracture frequency and conducting uphole seismic testing to determine changes in rock mass characteristics. The results from the three techniques show reasonable correlation. They suggest that major damage, in the form of fracturing of intact rock, occurs at least 7 m behind the smooth-wall blast and significant damage, in the form of opening and extension of calcite-filled fractures, at least 12 m from the blast. At greater distances the dominant damage mechanism is the loosening of existent joints within the rock mass. In the trachytes at El Soldado these damage mechanisms correspond to peak particle velocities of 2 000, 900 and 500 mm/s respectively

Jun 19, 1905

By G. Zhan, P. Mousset-Jones, G. Danko, J. J. K. Daemen, C. Mezei

Paper presented at the conference Risk assessment in the extractive industries, held in Exeter, 23-24 March 1994, and first published London: IMM, 1994, preprint volume. 18pp., 12 refs. (Originally entitled: Tunnel roof diagnosis using a robotic sensor test bed.) An integral roof diagnosis method is proposed to assist in assessment of risk regarding the stability of an excavation. A Robotic Sensor Test Bed (RSTB) is being developed for the characterisation of roof stability. The sensor test bed consists of a sonic/ultrasonic wave response sensor, a laser surface profiler and a surface temperature sensor. These sensors are mounted on an articulated robot manipulator for performing remote-controlled or fully automated diagnoses. A number of laboratory and field sonic/ultrasonic tests were conducted. A high-energy ultrasonic transducer and an impact device were used to resonate rock slabs. The fracture depths of the slabs were found to be inversely related to the measured resonance frequencies. The agreement between identified and actual dimensions was acceptable. Field tests also showed that loose rock on the surface can be clearly distinguished from solid formation by comparing their wave responses. The robotic laser profiler part of the RSTB was used to measure surface geometry. Different scanning methods are being developed to achieve the fastest and most precise measurements and to provide pertinent information about rock joints and major fractures

Dec 1, 1994

By Géssica Seara Faria

Foram fabricados compósitos de matriz de cobre, reforçados com grafeno a partir da mistura de uma dispersão de óxido de grafeno com pó de cobre eletrolítico. A dispersão foi produzida pelo método de Hummers modificado e caracterizada por espectroscopia Raman e difração de raios X. Os compósitos foram fabricados pelo processo de metalurgia do pó convencional. Os pós de compósitos foram caracterizados por microscopia eletrônica de varredura, os corpos de prova consolidados foram avaliados quanto a densificação a verde e do corpo sinterizado, e os corpos sinterizados foram submetidos a ensaio de compressão a fim de verificar a resistência dos compósitos.

Oct 30, 2017

Jan 1, 1966

By J. H. Holden

Operations involving the processing of coal, oxygen, and steam into synthesis gas by means of two pressure-type gasifiers have demonstrated the effect of heat loss and operating variables on carbon gasified and oxygen and coal requirements. Carbon gasified is the fraction of carbon in the coal that is converted to gas. Oxygen and coal requirement is the quantity of each that is needed to produce a unit volume (M std. c.f.) of carbon monoxide and hydrogen. Operating pressure of the gasifiers ranged from 150 to 300 p.s.i.g. and coal was fed at 200 to 500 lb./hr./cu.ft. of reaction-zone space. Oxygen-to-coal ratios were 8.5 to 10.5 std. c.f./lb. Heat loss and residence time have opposite effects on carbon gasified; increasing the heat loss decreases the carbon gasified, but increasing the residence time (by raising the operating pressure or reducing the coal-feed rate) increases the carbon gasified. The effects of these two factors are difficult to separate because they usually change simultaneously. A comparison of the results obtained from the operation of two gasifiers with different levels of heat loss, however, permitted the effect of heat loss to be separated from that of pressure and coal-feed rate. When the results were deter- mined on the basis of constant heat loss, increase of the residence time increased the carbon gasified until the reaction virtually had come to completion. For example, at 150 p.s.i.g., decreasing the coal-feed ratio from 500 lb./hr./cu.ft. to 200 lb./hr./cu.ft. substantially increased the carbon gasified. At 300 p.s.i.g., however, changing the coal-feed rate had little effect on the carbon gasified because the reaction had almost reached completion and further increase in residence time resulted only in a negligible change.

Jan 1, 1962

By W. J. D. Stone

In 1960, Magnetics International Ltd. undertook the development of the Jones High Intensity Wet Magnetic Separator in the Americas. Magnetics International had a number of possible applications in its own projects plus the intention of developing the equipment for sale to others. It was soon recognized that no matter how innovative a piece of mineral separation equipment may be, it takes many years and much finance before it is finally accepted for large scale use. For this reason, many good ideas die in their infancy. One of the chief reasons for such a time lag between conception and large scale implementation is the usual lack of finance to construct and put into operation a large demonstration unit. Even with a large unit for demonstration, the first major user usually requires a guarantee that is not normal in accepted separation equipment. Such problems are also normally accompanied by major design changes from the first conception.

Jan 1, 1971

By C. Pelley, S. Kelebek, G. Kunzel, S. Gregersen, M. Pollanen

A series of small-scale tests was conducted to evaluate the effect of micro-fracture development, imposed by blasting, on the material properties of the rock as well as its resistance to crushing and grinding. The uniaxial compressive strength, tensile strength, Poisson’s ratio, Pwave, S-wave velocity, point load test index, crushing, and grinding work indices were evaluated for samples without any blasting load and for samples which had received a variety of blast loads ranging from a single impact with a lowstrength detonating cord to a combination of impacts at different times and significant impacts with powder factors close to those used in practical blasts. It was shown that the rock mechanics parameters change even at low impacts, suggesting easier crushing of the rock. Damage values appear to be affected by timing as stress wave superposition affects the damage process. Fragmentation is achieved at higher impact levels while work index modification of the fragments is also observed when high powder factors are used, suggesting improvements in grinding.

Jan 1, 2006

By J. M. Gomes

Bench-scale flotation tests were conducted on two western tactite ores to study the recovery of tungsten and zinc minerals. The investigation, which is part of the Bureau of Mines ongoing program to develop methods for beneficiating minerals and metals from domestic low-grade ores, demonstrated the feasibility of producing scheelite, sphalerite, and their bulk concentrates. Sphalerite concentrates containing 51 to 53 pet Zn and less than 0.11 pct W03 were selectively recovered prior to scheelite flotation. Zinc recovery ranged from 85 to 91 pct. Scheelite concentrates containing 17 to 25 pct W03 were then recovered from the ore; tungsten recoveries ranged from 88 to 94 pct. Bulk flotation concentrates containing 84 to 91 pct of the W03 and 87 to 95 pct of the zinc also were prepared. More than 98 pct of the W03 in a bulk concentrate containing 9 pct W03 was extracted by autoclave leaching with a soda solution. The zinc remained in the leached residue.

Jan 1, 1982

By Nobuyoshi Yabuki

Building Information Modeling is a prevailing methodology in the building industry and half (by length) of the world's shield tunnels are in Japan. Accordingly, for shield tunnels from 2005 to 2007, we developed a product model called IFC-ShieldTunnel, which is based on Industry Foundation Classes (IFC), in order to meet the future demand for such a product model. IFC-ShieldTunnel was developed by adding new elements that are specific to shield tunnels and that are not included in the original IFC. The added elements include shafts, segments (A, B, and K types), waterproofing elements, segment joint elements, and ring joint elements. Furthermore, soil layers and void elements were created. Recently, we updated the product model by re-organizing the entities and correcting errors. We deployed the updated IFCShieldTunnel model in the construction of an actual shield tunnel in Tokyo for about a year from August 2010 in order to check its feasibility. In the verification process, first, segments were modeled using Autodesk Revit Structure 2011 and property data were assigned to each segment element. Next, a mapping between the original attributes of the entities of IFC and properties of IFC-ShieldTunnel segments was developed. Using this mapping and IFC?s IfcBuildingElementProxy function, we were able to convert the IFC data from Revit Structure 2011 to IFC-ShieldTunnel automatically. Segment data were also converted from Revit Structure to Google SketchUp by IFC-ShieldTunnel. Furthermore, the construction scheduling and cost data were converted from Revit Structure to EXCEL for 4D and 5D analyses of construction. We interviewed engineers who used IFC-ShieldTunnel and received positive comments about the utilization of the product model. Overall, our test demonstrated the feasibility of IFC-ShieldTunnel. In future work, we plan to apply IFC-ShieldTunnel to more projects and test its practicality.

Aug 1, 2013

By N. Nikolaev

La cantidad de métodos experimentales y analíticos no consideran los factores que influyen sobre el proceso de acción recíproca entre los elementos de sostenimiento y el macizo rocoso. En ese sentido, estamos en condiciones de separar dichos factores en grupos, reuniendo en uno los independientes, y en otros los relacionados entre sí. Por ello, el presente texto señala los métodos adecuados para determinar la influencia de un factor determinado o de un grupo de factores sobre el desarrollo del proceso a través de la determinación del tipo de cabeza de anclaje y de la pérdida de tensión final del anclaje con el transcurso del tiempo.

Jan 1, 1973

By C. O. Aksoy, H. Kose, K. Heasley, E. Yalçin

"In Turkey, the growing demand for lignite has resulted in increased lignite production and an emphasis on improving underground recovery. This has resulted in a gradual increase in the application of the retreat longwall mining method and also in the extraction of the safety pillars protecting permanent underground structures (drifts, shafts) in mines prior to their abandonment.Extracting these safety pillars presents a special hazard to mine employees and the stability of the mine. Often subjected to high stresses, the behaviour of these pillars is not always predictable. Special care must be taken to ensure that infrastructure does not collapse prematurely, and that working conditions remain safe. Otherwise the extraction must be halted, and the remaining coal lost.This investigation reports on a study of the stability of safety pillars during the final extraction phase of the Hustas mine in Soma, Turkey.” The model construction was based on mine plans, and material properties were derived from physical properties testing. Observed subsidence effects from other mining events were used to calibrate the overburden lamination thickness.The model results compared well with surface physical disturbance occurring as a result of mining, as well as with conventional longwall stress redistribution theory and underground observations. The study has shown that properly calibrated models can be useful in assessing mine safety during remnant pillar extraction. The LAMODEL results demonstrate the convenience of this easy to use software."

Jan 1, 2004

By Eugene T. Sheridan

The 25th annual survey of the peat industry by the Bureau of Mines, United States Department of the Interior, disclosed that 79 companies produced and sold peat from 81 operations in 21 States in 1958. Peat is a carbonaceous deposit, formed under water or in a water-saturated environment from plant material. It is the first stage in the development of coal and, when properly dried, can be used as fuel. Although 98 percent (estimated) of the total world production is used for energy purposes, the status of peat in the United States is somewhat unique in that none is used for fuel, and practically all is consumed as an agricultural product, chiefly for soil improvement purposes. The domestic peat industry has expanded rapidly since World War II, and production in 1958 was 327,813 net tons valued at $3,445,767. More than one-half million ton of peat was consumed in the United State in 1958, however, as 269,096 tons was imported.

Jan 1, 1959

By Doris M. Hyde

There were no significant changes in the mineral industries of the smaller Caribbean Islands during 1980. Imported petroleum requirements continued to erode economic gains that may have occurred in other sectors. Some relief may be forthcoming as more qualified Caribbean countries take advantage of Trinidad and Tobago's petroleum product financing program (see Trinidad and Tobago). There were no crude oil discoveries in these areas during 1980, although some geophysical testing around the British Virgin Islands and Antigua war underway. In March 1980, the Government of Antigua sold a 75% interest in the 16,000-barrel- per-day West Indies Oil Co. refinery to the Swiss Intermaritime Bank and Intermaritime Management Services for $6 million. The new refinery company is called the National Petroleum Co. Shutdown since 1976, it was originally planned for the refinery to reopen in 1980, but refurbishing has proved to be more extensive than anticipated. The reopening is now expected in 1981.

Jan 1, 1982