Search Documents

China has made great progress in thick coal seam mining, commonly characterized by longwall top-coal caving mining and single-pass longwall mining with a large cutting height. At present, the maximum mining thickness of longwall top-coal caving reaches 20 m while that of single-pass longwall mining approaches 8.8 m. The top-coal caving–related technologies have significantly improved the mining efficiency of thick coal seams and have also made a great contribution to the centralized underground mining of coal. Thus, the number of underground coal mines is greatly reduced in China. However, due to the increase of the mining height and the changes in mining operations, the overburden movement caused by the mining of thick coal seams is more intense, and the influence scope is larger, which brings a series of new problems on ground control of longwall faces. In order to enhance ground control and improve the mining efficiency of thick coal seams

Jul 28, 2020

By G. Bulut

The recovery of copper and cobalt from ancient copper slags from the Küre region of Turkey was investigated. A fayalitic-type of ancient copper slag containing 1.24% Cu, 0.53% Co and 53.16% Fe were subjected to an experimental study. Two different routes were followed to recover the metal values. The first route was roasting the slag with pyrite followed by leaching. The second route was flotation of the slags, roasting of the flotation tailings with pyrite and leaching. The second route was found to be suitable for the treatment of the copper slag studied. In the flotation step, a copper concentrate containing approximately 11% Cu was produced with a 77% recovery while 93% of the cobalt stayed in the tailings. In the roasting experiments, the effects of roasting time, pyrite: slag ratio and roasting temperature on the dissolution efficiencies of Cu and Co were investigated, and the optimum conditions were determined. In the tests, 87% of the cobalt dissolution was observed after one hour of roasting at 500°C with a pyrite: slag ratio of 3:1. The copper dissolution in the tests was 31%. Based on the results of this study, a process flowsheet is proposed for the evaluation of these slags.

Jan 1, 2007

IN 1906, soon after his arrival in New Zealand, a brief article was prepared by the writer on "The Salient Features of the Economic Geology of New Zealand," for the Journal of Economic Geology. In November, 1907, a somewhat similar paper, entitled "The Mineral Wealth of New Zealand," was read at the Royal Colonial Institute in London. The present contribution to the Transactions...

Jan 1, 1909

By M. Tangstad, B. Monsen, H. Midtgaard, R. Ishak, M. Syvertsen, I. Solheim

Charcoal is an interesting reducing agent because it is produced from growing wood which is renewable and does not contribute to global warming, provided that there is a balance between the felling of timber and growth of trees. In the biocarbon project the possibilities for using charcoal is investigated as well as other biological based and renewable reductants for ferroalloy production. The background for the project is that the Norwegian ferroalloy producers wish to contribute to reduction of CO2- emissions. This paper focuses on the use of charcoal instead of coke for the production of manganese alloys, and the consequences of doing so. Results from practical SiMn smelting experiments on a pilot scale have previously been reported, where only 12-14 % Si in the metal was obtained when charcoal was used. Recently we have attained satisfactory 18 %Si also for charcoal, but good results are indeed dependant on good furnace performance. There is no tradition for using charcoal for manganese production in Norway. A change from using mainly coke to the use of some charcoal will demand new routines for furnace operation, raw material and off-gas handling. Hence, characteristic properties of charcoal, which may cause change of furnace operation, have been measured and are compared to coke. The following results are presented: ?Thermal abrasion strength together with CO2- reactivity; important parameters for the performance of the upper part of the furnace. ?Coke-bed resistance; it will increase with the use of charcoal (a review of new results). ?Slag reactivity; a relevant method for testing slag reactivity of industrial reductants is of interest. The suggested method can serve for comparing slag reactivities towards graphite.

Jan 1, 2007

By John R. Hoskins

The Bureau of Mines conducted an investigation to more exactly define the influence of some end conditions on the laboratory-determined uniaxial compressive strength of rock samples. Limestone, marble, sandstone, and granite were used to provide a range of specimen modulus of elasticity from 2.7 X 106 psi to 10 x 106 psi. Four variables were studied: Nonparallelism and surface texture of specimen ends were the specimen variables investigated; the end platen size and the adjustable or spherical head friction were the machine variables studied. It was concluded that the loading ends of small laboratory models and samples should be prepared with surface irregularities that do not vary from a plane surface by more than 0.001 inch. It was also concluded that nonparallelism of the specimen ends should not exceed 8 minutes for a rigid head load or 15 minutes for an adjusting head load. The measured compressive strength of specimens prepared with these tolerances will be statistically the same with any diameter or thickness of platen and any degree of head friction if initial alinement of the specimen is assured.

Jan 1, 1968

By Janet A. Flinn, David G. Fileccia

Machine guidance and control systems have become more pervasive in the mining industry in recent years but not always from mining-experienced providers. Dozers, motor graders, scrapers, excavators, shovels, draglines, drills and haul trucks are just a few examples of the types of heavy machinery now equipped with global positioning system (GPS)-aided guidance systems. While equipment manufacturers are offering their own software, many only supply solutions for the machines they produce. The proliferation of GPS equipment manufacturers entering the machine guidance and control arena has resulted in a multitude of makes and models of GPS receivers. Some of these companies also produce their own guidance software. But they usually just specialize in a narrow range of heavy machinery. So customers are forced to use multiple systems and face new challenges in implementation, training, reporting and inter-system communication.

Jan 1, 2006

By Kevin Connor

During 1986, the Government continued with efforts to ease the country's almost total reliance on coffee exports for trade revenues by allocating 45% of the Government's budget to commerce and industrial projects. The collapse in coffee prices in 1985 continued to exacerbate the country's growing trade deficit, weakened currency, and dwindling reserves of foreign exchange in 1986. Amoco Burundi Petroleum Corp., a subsidiary of Amoco International Oil Co., continued with plans to drill at least two exploration wells in Lake Tanganyika in 1987. Both offshore and onshore drilling exploration was planned by Amoco Burundi. Any oil or gas finds were expected to have substantial impact on the Burundian economy, as a major portion of the country's trade deficit was directly attributable to petroleum and gas imports.

Jan 1, 1988

By L. J. Heaslip, J. M. Toguri, T. R. Meadowcroft, R. L. Addinall

"""Pilot Plant Operations"" is a final-year core course given to the Metallurgy and Materials Science students at the University of Toronto. This course involves a laboratory study of an industrial project at an industrial site. Details of this program are discussed and reviewed after eight years of experience. IntroductionEducators in the field of Metallurgy and Materials Science have long agreed that ""hands-on"" experience is an important component in the education of metallurgical engineers. This philosophy is reflected in the undergraduate curricula of most metallurgical schools. The major problems encountered with laboratory-associated courses are the requirements for equipment, space and funds for both purchase and maintenance of equipment. For example, consider an exercise in crushing and grinding treatment in a mineral processing laboratory. Such operations require the handling of tons of material and often equipment of large size. The problems of storage of ore, methods of handling and maintenance of equipment are a few of the concerns facing the department. Considering that metallurgical departments at universities are, in general, relatively small, the support to purchase and maintain largescale equipment becomes an annual budgetary concern. In reality, universities today are not geared to operate mini-pilot plant equipment, either in terms of space or personnel.For the above reasons, in 1972an undergraduate core course called ""Pilot Plant Operations"" was introduced to the fourth year curriculum in Metallurgy and Materials Science at the University of Toronto. This course consists of I to 2 full weeks (8 hrs per day) of pilot plant laboratory study at an industrial site on a project of mutual interest with the industrial organization whose facility is being used. The first 5 years of the program were carried out at the pilot plant facility at the Ontario Research Foundation; Stelco's Research Centre in Burlington, Ontario, was used for the last 3 years. The nature of the projects undertaken during the 8-year period is shown in Table 1."

Jan 1, 1980

Effects of DA as a Grinding Aid on Selective Grinding of Low-Grade Bauxite Effects of DA (a copolymer of acrylic acid and acrylamide) as a grinding aid on selective grinding of low-grade bauxite were investigated in this study. The addition of DA into the grinding system enhanced the selectivity of grinding and increased the A/S ratio in the coarse fraction of ground product, leading to improved throughput of grinding mills and alumina recovery. The results showed that DA decreased the viscosity of slurry significantly and hence improved grinding efficiency due to low viscosity at a high slurry concentration. Both the hydrogen bond formation and chemical adsorption existed between DA and the surface of bauxite particles. The adsorption of DA on the surface of bauxite could decrease stress needed for crack initiation and extending during grinding, prevent new-born crack surfaces from rejoining, and promote the expansion of the cracks.

Sep 13, 2010

By E. J. Sun

The ADS system was developed to reduce accidents related to haul trucks operating under low visibility conditions in surface mining and construction sites, which is based on the GPS, mesh-wireless networks, and the Google-Earth 3D graphic engine as the graphic interface and mine-mapping server. This system has the capability to pin-point and track vehicles in real time using a 3D interface, which is based on user-based AutoCAD mine maps using the Google-Earth graphics interface. All equipped vehicles are shown in a 3D mine map stored in a local server through a wireless network. When low visibility conditions are present, the system indicates available exit/escape routes for driver safety. The research results indicate that the ADS system potentially increases reliability and reduces uncertainty in open pit mining operations by customizing the local 3D digital mining map, constructing the truck 3D models, tracking vehicles in real time using a 3D interface and indicating available escape routes for driver safety.

Oct 1, 2009

The compilation of the sampling nomogram is an essential tool in the optimization of a sampling protocol and allows the operator to track the change in relative variance of the sampling error (the Fundamental sampling error) during steps of comminution and mass reduction in the process of recovery of the aliquot for analysis. The data required for the compilation of the nomogram are centred on the sampling constant K and the exponent, alpha (a) of the nominal fragment size. Five methods for establishing K have been identified, but two of them, the duplicate sampling analysis method and the heterogeneity test method purport to provide such constant. The step by step procedure for each of these two methods was examined using broken ores from three mines, Mponeng mine, Kloof mine, and Lily mine. Two of these mines (Mponeng and Kloof) are typical Witwatersrand-type gold mines, and the third is an Archaean-type shear related gold deposit situated in the Barberton Greenstone belt. The results suggest that the factor K derived using the heterogeneity test is very accurate, but applies only to a single size fraction in the spectrum of comminuted materials. The calculation of gold grain sizes using this method appear to be too small and do not conform with the results from detailed mineralogical studies. The factors K and alpha derived using the duplicate series analysis are appropriate for use across a wide spectrum of comminution sizes and also provide realistic gold grain sizes, comparable with the equivalent circular diameter of gold grains identified in mineralogical studies of the ores.

Jan 1, 2010

By J. D. Bateman

Introduction The lifting of restrictions on the development of radioactive mineral deposits by private individuals has re-opened the search for uranium in Canada to a large body of professionally trained prospectors. The entry of private capital and experienced prospecting techniques into the search for radioactive minerals has been enormously stimulated by the atomic developments of the past several years; and we can now look forward to the discovery of new productive sources of uranium. The rate of new discoveries will, how ?ever, depend on the effectiveness of the methods used. The large number of new pitchblende occurrences reported within the past several months is largely a measure of the energy with which the portable Geiger-Müller counter has been applied in the field. The counter is simply a 'radio' receiver tuned to one of the products of spontaneous atomic disintegration that is characteristic of all radioactive materials. Its effective use depends largely on how it is applied under the various geological and topographical conditions that ma y be encountered, and also on an understanding of its limitations. Extensive geological information relating to the occurrence of radioactive minerals in Canada has been accumulated during the past several years, and it is now possible to define in a general way many of the geological formations in which pitchblende and related minerals are likely to occur. Furthermore, prospecting can be localized in those parts of the favourable formations that offer the greater promise of containing commercial deposits. In this selection, the Geiger counter is the most useful tool available to the prospector for the actual detection of radioactive materials. As an example, an area of two square miles in the Northwest Territories, within which about a dozen pitchblende occurrences had been found over a several year period by conventional prospecting methods, yielded more than forty-five additional discoveries by application of the Geiger counter. Yet earlier attempts at prospecting this area with the counter had failed, due largely to faulty instruments and lack of experience in field application. The limitations of the counter are very considerable; but, when they are recognized, there is no more useful tool for the discovery of radioactive ores. It was not until 1944 that a practicable portable counter was developed, and then only by co-operation in the field by geologists and physicists. Officers of the Geological Survey of Canada working with physicists of the National Research Council brought about the development of the modern counter.

Jan 1, 1949

By P. E. J. Pitfield, S. D. G. Campbell

The regional structure of shear and deformation zones in the belt, which is recognisable in plan view on Landsat TM images, is interpreted in terms of a conjugate-shear model. Gold mineralisation is related to this framework at a variety of scales. The principal recurrent structural geometries hosting deposits at mines such as Motapa, Durban, Charliesona, Cecil, Sunace, Turk group, Queens district, How, Peter Pat, Matabele Sheba, Goodenough, Old Nic and Bushtick are associated with shear zones and folds and include conjugate systems (shears, shear intersections, kink sets), side-step systems (en echelon segmentation, duplexes, monoclinal inflections, antiform-synform couplets) and interactions of the two. Linear sections of shear zones are generally poorly mineralised. The same geometries are identifiable on all scales from local to regional, so sections of regional structural lineaments or areas within mines should be prioritised for further investigation or development on the basis of the gold-bearing geometries observed to be dominant locally

Apr 1, 1996

By D A. Edmunds

The most important development that has been taking place recently relating to mining operations in New Zealand would generally be regarded as being the Resource Management Law Reform. This has been widely publicised by the Government as a comprehensive review of the laws governing New Zealand's natural and physical resources. Submissions have been sought and a free phone provided to encourage public participation. Recently a Discussion Paper has been prepared by the Core Group coordinating the review to explain progress on Phase One (Ministry for the Environment, Directions for Change: A Discussion Paper, Wellington 1988). It outlines Government decisions already taken which impinge on the Review and describes the possible models for resource management laws. However, it is possible that some fundamental practical issues of significance to the mining industry will not be addressed and may be lost sight of in the much wider issues which are to be covered. The purpose of our paper is to address one of these issues namely, the interrelationship between any new resource management legislation and the Conservation Act 1987 (as recently amended) in the context of Ministerial consents. The importance of this issue can be seen from the fact that as at 7 June 1988 there were 279 mining licence applications and 223 prospecting licence applications waiting to be determined by the Minister of Conservation. Since April 1987 only 19 mining and 13 prospecting licences have been consented to. In addition a major proportion of New Zealand's mineral resources are contained with land administered by the Department.

Jan 1, 1988

By C A. Locke

Geophysical signatures of the Taranaki and Tongariro volcanoes reflect similarities in their age, composition and hydrothermal histories, but also reflect differences in host rock settings and edifice evolution. The Taranaki volcanoes have strong positive gravity anomalies showing that their edifices largely consist of dense andesite which reflects substantial lava production or dyke injection during construction and that large sub-edifice dyke/stock complexes occur. In contrast, the Tongariro volcanoes have strong negative gravity anomalies indicating low density edifices of volcaniclastic material; no sub-edifice intrusions can be identified, probably because of the lack of density contrast with host basement rocks. Strong positive magnetic anomalies over the younger cones can mainly be attributed to near-surface andesite lavas or dykes whereas subdued magnetic effects are associated with hydrothermally altered zones within both edifices and sub-edifice intrusions.  

Jan 1, 1995

By S. T. Camagu, J. Dutta Majumdar, S. L. Pityana

Laser surface alloying was used to develop copper and molybdenum aluminides by injecting premixed copper and molybdenum powder particles into a laser-generated melt pool on an aluminium substrate. Different laser processing parameters were used to produce the composite thin layers on the substrate material. The microstructure and phase constituents of the composite layer were studied by means of scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and X-ray diffraction (XRD) techniques. Experimental results show that the matrix structure of the metal matrix composite layer consists of ?-CuAl2and MoAl5. Surface hardness was increased by a factor of 3.

Jan 1, 2015

By Jr. Jacobson

Thermal reactions of l-methylpyrrole, l-butylpyrrole, and l-isopropyl-pyrrole were investigated by a flow method in the temperature range of 4500 to 5750 C. Those of I-butylpyrrole and l-isopropylpyrrole were also investigated in the 3400 to 4000 C range in a static system. The I-substituted pyrroles isomerize by an irreversible reaction to 2-substituted pyrroles. A reversible isomerization reaction shifted the alkyl group from the 2-to the 3-position on the pyrrole ring. All of the isomerization reactions are homogeneous, unimolecular, nonchain, first-order reactions having similar mechanisms and transition states. There is decomposition and cleavage of the longer alkyl side chain when it is in either the 2-or 3-position giving, as products, pyrrole, 2-and 3-methylpyrrole, 2-and 3-ethylpyrrole, pyridines, and hydrocarbons. The decomposition reactions appear to be by free-radical mechanisms. Pyridine homologs are formed by the expansion of the alkylpyrrole: butylpyrrole produces pyridine, and isopropylpyrrole produces 3-methylpyridine. Approximate Arrhenius equations are given for the formation of the decomposition products.

Jan 1, 1966

By H. Winkelmann

The author, who himself has worked inn the field with various types of torsion balances, expresses in the article his experience with the recently marketed Haff-Torsion-Balance. The advantages of practical work with Haff?s s torsion balance as compared with other types are mentioned. In spite of low weight and corresponding small dimensions (Model M = 23.5 kg., Model Al = 11.5 kg.) the sensitiveness is not less than that in the largest instruments. It is at 1.10-9, which is proved by calculations. A comparison with the corresponding values of other types of torsion balances (Eötvös, Askania, Gepege) is given. The mechanical features of the instrument are briefly described, and the balance is illustrated by a, cross section of it. -- W. Ayvazoglou. DETERMINATION OF THE ELEMENTS OF THE MAGNETIC AND GRAVITATIONAL FIELDS INDUCED BY AN INFINITELY LONG HOMOGENEOUS CYLINDER By G. A. Gamburzeff Gerlands Beiträge zur Geophysik, Band 19, Heft 2/3 Leipzig, 1928, pp. 210-230. The present work is a. contribution to the quastion of the reason for the magnetic and gravitational anomalies in the government of Kursk (Russia).

Jan 1, 1929

The Gippsland Basin, southeastern Australia, has an Upper Cainozoic history of episodic change of hydrology and the related environment, reflected in the geomorphology and surficial deposits of the onshore basin and the hydrodynamically controlled accumulations of petroleum of the offshore basin. Succeeding this episodic pattern, man through a number of activities, has had a sudden and major impact on the hydrology and the related environment. Activities include those directly affecting the groundwater system, such as extraction of fossil fuels with the consequent threat of land subsidence; irrigation and clearing of vegetation and the consequent effect of salinisation; change of land use and installation of septic tanks with resulting nitrate pollution; damming of streams and the consequent reduction in the frequency of floods with degradation of the biological Environment; de-snagging streams and construction of cutoffs with increased stream erosion, modifying wetlands including drainage, with the consequent degradation of their ecosystems; and increase in phosphate and nitrate inputs to the coastal lakes with the risk of their eutrophication.

Jan 1, 1992

By A. S. Usrnani

Due to both turbulence and the highly variable geometry of castings, a realistic numerical simulation of the metal flow is prohibitvely expensive with current technology. However, when the chief purpose is to achieve realistic thermal fields a precise How simulation is not necessarily required. In this paper we assume a laminar flow regime and obtain the flow field by solving the incompressible Navier-Stokes Equations using a velocity-pressure segregated semi-implicit finite element method. The free metal surface is predicted by advecting a pseudo-concentration function via the computed How field. This involves an explicit finite element solution of a pure advection equation. The thermal field is calculated by solving the convective-diffusive energy equation by an explicit finite element method using the computed flow field and the location of the free surface. All the advection terms are discretized using a Taylor-Galerkin method. The interface between the metal and mould is modelled using special interface elements. The model is demonstrated by solving practical example problems. The results show that a sharp thermal front is maintained during the course of filling without excessive diffusion. The heat diffusion in the mould can be controlled by varying the metal mould heat transfer coefficient.

Jan 1, 1994