Search Documents

By A. J. Petrina

"At Craigmont Mines Limited, Merritt, B.C., tests were begun in March, 1965 to evaluate the use of shotcrete as a method of ground support m development headings; previously, ail drifts had. required support, which was accomplished mainly by timber and occasionally by the use of rockbolts. The tests demonstrated conclusively the effectiveness of shotcrete for supporting Craigmont's ground. Gradually, the use of timber for ground support was virtually eliminated in favour of shotcrete. This paper describes the equipment used, the operation of the equipment, pertinent cast data and opera ting details. Also discussed are other uses developed for the shot-creting equipment, the use of reinforcing bar rockbolts, and a method used at Craigmont for lining long vertical ore passes with steel plate and concrete as part of the raising cycle."

Jan 1, 1968

By O A. Cottrill, G A. Oldfield, S B. Nowell

Host-rock û wallrock major and trace element geochemistry associated with epithermal gold mineralisation in the Hauraki Goldfield of New Zealand is poorly documented, even though rock geochemistry is a recognised tool in exploration. Such responses assist in recognition of the regional scale imprint of fossil hydrothermal activity, and indicate targets for detailed evaluation within these alteration zones.   Recent investigation of gold deposits in the Waihi (Gladstone), Golden Cross (Empire), Thames (Waiotahi) and Coromandel (Tokatea) areas indicate enrichments of Au, As and Sb in the andesitic wallrocks hosting mineralisation. Of the other elements examined, Si, K and Rb are enriched, and Na, Ca, and Sr are depleted at all deposits. These trends are best developed in the vicinity of veining. In deposits with clay alteration dominating (Waiotahi and Tokatea) there is also depletion of Mg, Mn, Zn and Cu. Ba and Cr are variably enriched or depleted within different styles of alteration. Base-metal enrichment in the wallrocks is not a feature of Hauraki deposits.

Jan 1, 1990

By Gualberto Salas

Dado que la voladura es una de las operaciones unitarias de mayor extracción del mineral -en tanto logra una adecuada fragmentación de la roca con un costo reducido, es necesario lograr una interrelación entre los resultados de la voladura y el de las operaciones unitarias como herramientas que evalúan y optimizan los diseños de los disparos. En ese sentido, el presente trabajo describe las técnicas para el diseño de las mallas de perforación, los programas para la simulación de la voladura y también para medir los resultados, que permitirán realizar los ajustes necesarios para mejorar los resultados de fragmentación y reducir el costo de operación de minado.

Sep 13, 2001

By M. S. Klima, P. T. Luckie

Proper analysis of washabiity data can lead to the development of a maximum yield coal preparation plant flow sheet. Simulations, as simple as spreadsheet mass and water balancing, are important in examining yield maximization and middlings liberation. Key to such attribute tracking flow sheet simulations is the distribution model, expressing the probability of a species reporting to the product stream. There are many such models in the literature. This paper examines a functional form that can represent or fit most of the proposed distribution functions.

Feb 24, 1997

By A. McLean, M. Iwase, K. Wakimoto, K. Katogi

For many decades control strategies have been based upon samples taken from liquid steel, molten slag and gas phase as well as from solid products. Because of recent developments in the areas of dynamic control models, artificial intelligence and expert systems, there is an increasing incentive to develop diagnostic sensors, which permit in-situ rapid determinations of concentrations of various elements in molten steel. In this paper, an overview is given on recent developments in the areas of sensors for use in ferroalloy and steel production. Particular emphasis will be given on (i) innovative application of sensors for on-line determinations of dissolved elements, Si, P, N, H and Cr in molten iron and ferroalloys, (ii) evaluation of inclusions in liquid metal and (iii) rapid determinations of slag compositions.

Jan 1, 2004

By D Barclay, S Mercer, S Wright

Mine water management is often an afterthought in mine planning processes and can introduce significant risks to projects when studied as a stand alone component at a later stage in the mine design. Incorporation of a mine dewatering and pore pressure dissipation strategy in the early stages of mine planning is imperative in order to minimise constraints on the production schedule, to match designed pit slopes and maximise project value for an open cut mine option such as Olympic Dam. A risk-based mine planning approach was adopted during the project selection phase study whereby water management was introduced into mine planning, scheduling and the development of an operational strategy. Hydrological and hydrogeological studies and outputs were successfully integrated into the various iterations of the mine planning cycle during early selection phase to manage the potential water management risks associated with pit slope depressurisation and access to dry working conditions during rapid advancement of mining phases.An extensive network of vibrating wire piezometer sets and long-term depressurisation testing characterised aquifer conditions and demonstrated that hydraulic connectivity exists within the geological profile due to the presence of structures and resource drill holes which enhance vertical connectivity. This connectivity, along with underdrainage from mining activities contributes up to 100 m of depressurisation in low permeability units.A pit dewatering strategy incorporates the mine planning schedules and accounts for operational constraints as to the location and development of the dewatering wells, storages and pipelines. Numerical modelling generated a range of likely pit inflows and dewatering requirements with the average initial dewatering discharge likely to be 150 L/s and reduce quickly to 50 L/s after five years, depending on the premine schedule.Coupled hydrogeological and geotechnical assessments were also carried out as part of the mine planning cycle and indicate that successful dewatering will go a long way to reduce the pore pressures within key geotechnical units during the rapid mining phase where around 300 m of cover sequence is stripped in five years. However, the residual storage in the primary aquifer and the residual pore pressure in underlying low permeability units will need to be dissipated (in-pit horizontal holes) as the pit floor advances. Pit slope design angles are sensitive to depressurisation and dewatering and up to 70 per cent depressurisation of key geotechnical rock units are required. Whilst an accelerated program of aquifer dewatering supported by lithostatic unloading should drive rapid depressurisation in the lower permeability units, intervention is anticipated in key geotechnical units such as the Tregolana Shale and volcaniclastics. The extent of induced drainage will ultimately depend in part upon the mining rate and geotechnical stability requirements. Practical operability testing addressed the potential for operational constraints to mine depressurisation activities such as congestion and mining schedule development within the pit and identified that depressurisation drilling can be achieved even with reduced access availability. Mine operations and planning groups established design criteria and considered the likely inoperable periods following rainfall events of seven to 14 days to manage the base surge and minimise impact on production. In-pit surface water management options to minimise operational disruptions during and after significant rainfall events were estimated used a stochastic approach.

Jan 1, 2009

By A. Roberts

This paper reviews progress in equipment design and in the techniques applied to mine lighting in Great Britain. The incidence of the disease miner's nystagmus, which was a major source of concern only a few years ago, has now diminished, largely owing to improvements in standards of lighting in mines. The reorganisation of the coal mining industry, involving increasing mech-anisation, together with new safety legislation, has brought about the widespread use of mains electric lighting underground. An account is given of some of the results of research to determine the lighting conditions needed for compliance with the compulsory legal requirement of "sufficient and suitable" general lighting at specific localities in British mines. Some details are given of the techniques applied and the results of recent research in the problem of glare from miners' cap lamps. Of the various factors in the working environment of the miner, it is true to say that lighting is seldom given attention comparable with that devoted to other factors, such as dust, heat and humidity, or atmospheric gas content. No doubt one reason for this lies in the ability of the human eye to adapt itself to low brightness levels. Be that as it may, the fact is that at the turn of the 20th century the miner's working light improved little throughout the centuries during which mining technology has developed. Indeed, in coal mines which encounter a methane explosion hazard, flame safety lamps, with a luminous intensity less than one candle power, were virtually the sole means of lighting during almost the whole of the 19th century. The 20th century has witnessed a substantial improvement in lighting techniques underground in coal and metalliferous mining. In Great Britain the general pattern has been one of standards periodically raised by the implementation of Statutory Regulations imposed under successive hlines Acts, but it is fair to add that the more progressive mining companies usually anticipated the Statutory Regulations, which when they have been put into effect have served to turn into general practice what was already being done at the better mines. In earlier years, official requirements were limited to the specification of approved lamp designs, with stipulated minimum values of luminous intensity and light output, but more recently the necessity of satisfactory maintenance of standards during service has been recognized, and the current regulations not only require that a maintenance organisation should exist, but also specify a maximum permissible depreciation below initial approval standards.'

Jan 1, 1961

By Xiang Yu

Hong Kong has a dense distribution of utility services laid under its road network. Utility undertakers frequently demand road openings to install new services and/or maintain existing ones. Road openings can cause troubles to the road network and negatively impact the public interest. Highways Department is responsible for managing road openings in Hong Kong under the Land (Miscellaneous Provisions) Ordinance. Highways Department has spent a lot of efforts to computerize excavation permit processing and utility management. The computerized system has gone through several generations and the current one is called the excavation permit management system (XPMS). On the one hand, the XPMS handles various excavation permit processing functions including permit application/approval/refusal/issuance/extension/termination, fees/costs, permit conditions, and permit period assessment; on the other hand, the XPMS accounts for some important utility management issues such as spatial check, coordination of multiple openings, traffic management, audit inspection, and defect liability. This paper discusses how the application, coordination, and other administrations of an excavation permit are eased by using the XPMS in Hong Kong. Background information such as the governing legal and regulatory framework, and Highways Department?s administrative structure is introduced. The system architecture and advantages of the XPMS are presented. The work procedures and various functions of the XPMS are studied in detail.

Aug 1, 2013

By J. E. Davidsen, M. Honstad

"A well-maintained tap-hole channel is important in order to achieve good and stable furnace operation over time. A worn or short tap-hole channel can lead to more violent flow, significantly increasing the fume emissions during tapping and leading to more metal being mixed with and lost to the slag. Over time, a worn tapping channel might cause side channels and damage to the lining around the tap-hole area. This can result in a burn-through which is a considerable safety risk and will cause significant production losses. At Eramet Norway Porsgrunn, tap-hole maintenance has been done regularly with electrode paste for over three decades with good results. This article summarizes some of the experiences obtained from this practice on a 33 MW SiMn furnace, as well as a change to a coal tar pitch-free binder. IntroductionA well-maintained tap-hole channel is important in order to achieve good and stable furnace operation over time. Metal and slag are regularly tapped from the furnace and may cause a lot of wear on the tapping channel, increasing the risk of lining damage and ultimately leading to a burn-through. On furnace 10 at Eramet Norway Porsgrunn, the tap-hole area is the part of the lining that has been by far the most prone to burn-through since the startup of the furnace.Experience shows that almost all lining problems have started with burn-through in the tap-hole area or in close proximity to the tap-hole. During tap-hole repairs, side channels with metal and slag have also been observed emanating from the main tapping channel. In addition, a shorter tapping channel will cause more violent flow. This can lead to more metal droplets being entrained in the slag, and increase the risk of the furnace not being closed properly at the end of the tap.As a burn-through is a considerable safety risk, and also causes significant production losses, systematic work has been performed over the years to maintain the tapping channel in order to prevent burn-through."

Jun 1, 2019

By R. J. C. MacDonald

"The first recorded discovery of placer gold in Canada was on the Chaudiere River in Quebec's eastern townships in 1832 and the first major production came from placer deposits in British Columbia in 1858 (Verity 1974). Placer deposits were the major source of gold until the late 1890's, although lode deposits were found in Nova Scotia in 1862. In 1896 the Klondike Gold Rush commenced with the discovery of gold by Henderson and Carmack in the Yukon. The peak was reached in 1900 when over one million ounces of gold valued at approximately $22.3 million were recovered. With the exhaustion of the easily accessible deposits, more capital intensive operations were necessary such as those initiated in 1906 by the Yukon Gold Corporation. This giant dredging operation continued to produce until 1966. Today only a few small operations remain.The development of Canadian lode gold mining began in earnest around 1900 when the railroads were opening up the interior and western part of the country. At this time many discoveries occurred, particularly where mineral outcroppings were near surface. Tremendous impetus for exploration and the reopening of former producers followed the elimination of the gold standard by Great Britain around 1931, and more importantly the United States in 1933, with subsequent stabilization of the price of gold at $35 per ounce in 1934. Prior to this the price of gold was basically unchanged since 1717, approximately, $20 per ounce (Verity, 1974; Green, 1973).The depression of the 1930s adversely affected most industries, however for the gold producers it was a very profitable time. Prices of materials and equipment declined and labour was cheap and plentiful. Interest in gold mining was further stimulated in 1936 when a three year tax exemption was declared for all new metal mines. In 1938 a decline in the value of the Canadian dollar relative to the U.S. dollar benefitted the industry. The second world war provided yet again further incentive for gold production and in 1941 Canadian gold production reached a high of approximately 5.4 million ounces. This figure was not surpassed until 1991 when approximately 5.6 million ounces were produced (Natural Resources Canada, 1996 )."

Jan 1, 1998

By John C. Lyons

"The Wabana iron ore deposits occur as flat-dipping beds of oolitic hematite and chamosite, of Lower Ordovician age, which outcrop for 3 miles along the northwest coast of Bell Island, Conception Bay, Newfound-land, about 16 miles from St. John's.The deposits occur in three zones, Upper, Middle, and Lower beds, separated respectively by 30 feet and 215 feet of shale and sandstone. They are primary sediments laid down in a shallow tidal basin by the precipitating action of a marine environment on iron-rich fresh waters flowing into the basin.The ore-bearing zones, while of wide areal extent, are not uniform beds of hematite that can be mined wholesale. The action of waves and currents during sedimentation; the delta pattern, velocity, and transporting power of streams flowing into the basin; the contours and oscillations of the sea bottom on which the sediments were laid have all been fundamental in the emplacement of richer and thicker mineable sections, and of lean zones so intercalated with shale as to be unmineable.The preservation of the deposits is due to their location in the Conception Bay syncline and to a considerable upthrust of the country east of the bay in post-Ordovician time.The hematite deposits were first recognized as such in 1892, and soon after were acquired by the Nova Scotia Steel and Coal Co. They are now being mined by Dominion Wabana Iron Ore, Limfred, a wholly owned subsidiary of the Dominion Steel and Coal Corporation, Limited. Production started in 1895, and up to the end of 1955 totaled 58,588,516 long tons of hematite ore, having an average dry analysis of about 51 5 per cent iron, 11 8 per cent silica, 0·9 per cent phosphorus, and l ·5 per cent moisture. About 40 per cent of the total tonnage mined has come from surface stripping and on-shore mines. These areas have now been almost completely depleted, and operations are confined to submarine mines extending for two miles off shore under the waters of Conception Bay. Three sub-marine slopes are currently in operation, Nos. 3 and 4 working in the Lower Bed and No. 6 in the Middle Bed. A general picture of the workings is shown in isometric projection in Figure 1. Submarine mining has been entirely by the room-and-pillar method, with an extraction of 60 per cent. The deepest workings, at a vertical depth of 1,850 feet below sea-level, have a rock cover of about 1,500 feet. No mining is done in areas where the rock cover is less than 200 feet. To date mining has explored six square miles of a potential area that may exceed 50 square miles."

Jan 1, 1949

By L. Arnberg, E. Ott

The microstructure of ferrosilicon is important since it controls the disintegration of the material during crushing and thus the generation of fines. Therefore a study of the microstructure formation during solidification of pure FeSi(75wt%Si) and FeSi(75wt%Si) containing 1.2wt%Al and 0.2wt%Ca has been initiated. The material has been cast into rods of 8mm diameter, which have been remolten by induction heating and directionally solidified in a Bridgman apparatus. This allows the temperature gradient and the growth rate to be controlled independently. The temperature history during solidification has been recorded by a thermocouple in the melt. Growth rates have been varied between 5 and 400µms-1 and temperature gradients between 3 and 14°Kmm-1. The microstructures show a large dependence on the solidification conditions. The crack formation in the alloys has been studied and found to be strongly related to the microstructure.

Jan 1, 2004

By Van Dusen M

The involvement of concerned parties in all aspects of the Lihir Project from an early stage has promoted good relations between all groups. Activities involving landowners, the Lihir community, the New Ireland Provincial Government (NIPG) and the prospective developer include the Lihir Liaison Committee, Lihir Working Group, Environmental Planning Committee, Provincial Mining Task Force and the Lihir Mining Area Landowners Association (LMALA). With modifications, the Lihir Liaison model may be of use in promoting good relationships among parties in other mineral developments.

Jan 1, 1991

The United States Bureau of Mines is establishing a computerized mineral inventory system to help the Federal Government appraise its mineral position and prepare programs insuring against critical shortages of materials. This system, called the Minerals Availability System (MAS), is a component of the Bureau's minerals intelligence function designed to conduct and maintain an inventory of minerals important to the Nation. The MAS defines the physical and commercial availability of the mineral resources. Known resources are evaluated and classified by deposit for entry into a computer storage and retrieval system. An integral concern of these evaluations is the cost of mining and beneficiating the ore contained in specific deposits. To meet this concern, a cost handbook was developed as an aid to preparing feasibility-type estimates for capital and operating costs of mining and primary beneficiation of various types of mineral occurrences. Cost data, obtained from U.S. and Canadian companies, were used as the basis of this handbook. The handbook presents cost curves and equations for each component of the mining and beneficiation process. Factors for each cost component are also given, thereby allowing the updating of cost for time, geographic location, labor rates, and mining and milling conditions. Included in the latter conditions are items such as the length of haul, need for rock bolts, and a rock work index for ores and rocks of various hardnesses. 1.2. USE OF THE HANDBOOK Using the handbook a feasibility-type estimate falling within 25% of expected actual cost is obtainable by summarizing cost components. This handbook should not be used to determine the cost of any single component of a mining or beneficiation system, as any single component may not fall within the 257 limit. It must be understood that anyone who uses the handbook must have a comprehensive knowledge of mining and processing technology and cost estimating procedures. The handbook was intended to be used internally by the Minerals Availability System. Because

Jan 1, 2012

By Fujio Ishii

The deoxidation of liquid nickel and nickel binary alloys with silicon has been determined at temperatures between 1500°C and 1650°C using quartz crucibles in order to investigate the deoxidation of nickel based alloys. The equilibrium constant of the deoxidation reaction in liquid nickel and the effects of the different alloying elements such as chromium, molybdenum, tungsten, iron, cobalt and coppcr on the activity coefficient of oxygen in liquid nickel have been established.

Jan 1, 1993

By S. E. Phillipson

Underground mine mapping is a critical component of understanding the controls on ground instability. Many relatively localized examples of ground failure are associated with geologic features, such as faults, joints, compaction zones, or sedimentological transition zones. In contrast, long-running, directional roof falls are associated with regionally directed horizontal stress fields, which are induced by tectonic plate interactions in the earth?s crust. When stress-related features are distinguished from geological features, underground mapping can be an effective method for inferring the direction of horizontal stress at individual mines. Comparisons with data compiled in the World Stress Map confirm that underground mapping can be a valid method for determining the orientation of maximum principal horizontal stress at a variety of scales, ranging from individual mines to an entire mining district or coal basin. Comparisons are presented between the maximum horizontal stress directions inferred by MSHA?s Roof Control Division through underground mapping and the azimuths of maximum horizontal stress in the World Stress Map database for North America?s Pennsylvanian-aged Appalachian, Illinois, Black Warrior, and Arkoma Basin coal fields. The comparison indicates that azimuths are similar for both data sets, even where variations in the direction of horizontal stress are present. It is interpreted that inconsistencies in direction are attributable to near-surface affects such as deeply incised stream valleys, or to fault zones that represent heterogeneities in the crust.

Jan 1, 2009

By Don Welch

Pressures for change ?Land use constraints ?Project financing ?Local communities ?Environmental issues ?Sustainability requirements ?Stricter regulatory procedures ?Technical excellence ?Reduce risk ?Impacts of failure & non-compliance

May 1, 2010

By Herbert Clark Hoover, Lou Henry Hoover

SINCE the Sixth Book has described the iron tools, the vessels and the machines used in mink, this Book will describe the methods of assaying1 ores; because it is desirable to first test them in order that the material mined may be advantageously smelted, or that the dross may be purged away and the metal made pure. Although writers have mentioned such tests, yet none of them have set down the directions for performing them, wherefore it is no wonder that those who come later have written nothing on the subject. By tests of this kind miners can determine with certainty whether ores contain any metal in them or not ; or if it has already been indicated that the ore contains one or more metals, the tests show whether it is much or little ; the miners also ascertain by such tests the method by which the metal can be separated from that part of the ore devoid of it ; and further, by these tests, they determine that part in which there is much metal from that part in which there is little. Unless these tests have been carefully applied before the metals are melted out, the ore cannot be smelted without great loss to the owners, for the parts which do not easily melt in the fire carry the metals off with them or consume them. In the last case, they pass off with the fumes ; in the other case they are mixed with the slag and furnace accretions, and in such event the owners lose the labour which they have spent in preparing the furnaces and the crucibles, and further, it is necessary for them to incur fresh expenditure for fluxes and other things. Metals, when they have been melted out, are usually assayed in order that we may ascertain what pro- portion of silver is in a centumpondium of copper or lead, or what quantity of gold is in one libra of silver ; and, on the other hand, what proportion of copper or lead is contained in a centumpondium of silver, or what quantity of silver is contained in one libra of gold. And from this we can calculate whether it will be worth while to separate the precious metals from the base metals, or not. Further, a test of this kind shows whether coins are good or are debased ; and readily detects silver, if the coiners have mixed more than is lawful with the gold ; or copper, if the coiners have alloyed with the gold or silver more of it than is allowable. I will explain all these methods with the utmost care that I can.

Jan 1, 1950

By I. O. Ojala

Detailed knowledge of velocity-depth trends is essential for constructing well-to seismic ties, determining background velocity and generating synthetic seismic traces for interpreting seismic amplitudes in terms of porosity, lithology and pore fluid type. The acoustic properties of shales are of particular importance in the exploration setting as shales constitute more than 80% of sediments and rocks in siliclastic environments. Seismic and sonic log data may be used for estimating overpressure in shales in order to maintain borehole stability during drilling. In addition, velocities in shales can be used for predicting its mechanical properties and hence, borehole collapse. Despite of the apparent importance of understanding shale acoustics, sonic logs in shales are frequently unavailable or unreliable especially for older wells. Hence, it is essential to compute pseudo-velocity logs from other available information. This can be accomplished by using empirical relationships or rock physics transforms. In this study we have compared the predictive power of resistivity (Faust 1951, Hubert 2008) and porosity based models (Wyllie 1956, Holt & Fjær 2003) for computing synthetic P-wave velocity logs using wireline log data from mudstone intervals at three North Sea wells. The wells 6507/2-1, 6507/2-2 and 6507/2-1 are located at the Haltenbanken area at the Norwegian Sea. The wells targeted hydrocarbon potential at the upper Cretaceous and lower Tertiary sandstone sequences. The sandstone beds are overlain by thick Tertiary and Cretaceous sequences of mudstones. Since our primary goal is to model acoustic velocities in shale, we used wireline data from the Nordland (NL), Rogaland (RL) and Hordaland (HL) groups that are mainly composed of mudstone. The mudstone beds were identified from the well log data by using natural gamma log, sonic and resistivity data as well as information from the Norwegian Petroleum Directorate website. The volume of shale was estimated from the natural gamma log and the data points with values higher than 0.65 were discarded. Similarly, the data points with shale volume less than 40 % were discarded. Furthermore, exceptionally high resistivity values amounting to more than 6 Ohm m were not included in the analysis. Porosities were determined from the density log assuming 2.7 and 1.05 g/cm3 for matrix and fluid densities, respectively. The depth that was used for calculating Vp from Faust (1953) was the depth below mudline in order to the compare of well data from wells that have been drilled at different depths (Hubert 2008).

May 1, 2009

By Stanley G. Hutton, Robert Brubaker

"It has long been recognized that mining workers subjected to high levels of hand-transmitted vibration may suffer from vibration-related complaints. Prolonged exposure to whole-body vibration may also result in adverse effects. In this study, the effects of vibration on mining workers are examined. Previous work documenting the occurrence of vibration-related disease is reviewed. From this work, it is apparent that operators of hand-held pneumatic rock drills are exposed to a significant risk of developing vibration disease. Vibration levels recorded on the rock drills now in use are presented and shown to exceed levels recommended by a proposed ISO standard.IntroductionThe possible harmful effects of exposure to excessive vibration levels have long been recognized, particularly among operators of hand-held tools. Numerous cases have been reported of a vasospastic disorder commonly known as vibration white finger disease (VWFD), which was a term coined by the Industrial Injuries Advisory Council in Scotland in 1970(1 ), Those suffering with the disorder have frequent vasospastic attacks in which the fingers, hand and, in advanced cases, the lower arm turn white and numb, usually after a cold stimulus. Advanced stages of VWFD have been reported in which the skin becomes ulcerated and gangrenousm. The incidence of the disease has been particularly serious in the forest industry due to the extensive use of chain saws. However, in recent years, the introduction of antivibration saws has resulted in a significant reduction in the occurrence of the disease.In a recent report for the Canadian Department of Supply and Services - Energy, Mines and Resources, Hutton & Brubaker considered the effects of vibration on workers in the mining industry. In this report, the physiological and medical effects of vibration were considered, relevant vibration standards were discussed, previous vibration measurements were documented and field measurements carried out. In the present paper, the results recorded in this study will be summarized, together with results that have been previously published relating to vibration levels existing in the mining industry."

Jan 1, 1982