Search Documents

By D. F. Malan, J. A. L. Napier

This paper describes some important aspects associated with historical underground measurements in South African gold and coal mines. Deformation measurements were used to confirm the use of elastic theory to simulate the rock mass behaviour in the Witwatersrand gold mines in the 1960s. Although a prominent time-dependent component of stope closure was measured as early as the 1930s, it was ignored owing to the benefit of adopting elastic theory. Neglecting the time-dependent response of the rock for many decades resulted in important aspects such as the effect of mining rate, the effect of advance per blast, and the need for enhanced design criteria not being explored. Recent work is only now starting to address this gap in knowledge. In-situ measurements of large coal specimens in the 1960s and 1970s indicated that a linear formula may possibly be a better approximation of coal pillar strengths. This alternative formulation was never adopted, however, as the power law strength formula was already deeply entrenched in the industry at that stage. In spite of these apparent failures to continuously generate and adopt new knowledge, a key lesson learnt is that major advances in rock mechanics will not be possible without careful monitoring of the rock mass behaviour in experimental sites. Areas requiring further research, such as pillar strength formulae for the Bushveld Complex and enhanced design criteria for the gold mines, can only be developed using extensive undergroundmonitoring programmes.

May 1, 2021

By S. V. Ulianov, A. Y. Senchenko, E. M. Kurchevskaya

"A process sample of old copper-containing tailings (-2.0+0 mm) from an iron-ore plant was tested in TOMS institute in order to develop a process for copper concentrate production. The study of tailings material composition indicated that -0.2+0 mm fraction was efficient and contained 97.26% of copper. Copper is predominantly concentrated in chalcopyrite which is present both in free form and in intergrowth with ore and rock-forming minerals. Study of chalcopyrite using an optical microscope and Qemscan SEM determined that the most grains surface was covered with oxide films. Additionally, a lot of grains had micropores on their surfaces that indicated a partial mineral leaching. The oxide films did not make it possible to float copper minerals from head material. It was recommended to apply an attrition operation to restore chalcopyrite floatability. In order to increase selectivity a regrinding stage for a primary copper concentrate was introduced to obtain P80 26 um. Taking these recommendations into account a flotation flowsheet was developed to process the old Cu-containing tailings. The flowsheet allowed us to obtain a concentrate with 23.5% Cu content at 71.5% recovery.INTRODUCTIONStudy of material composition is an important prerequisite for development of a minerals processing technology. Mineralogical study contributes to search for an efficient technology to recover valuables and for prospective methods of minerals processing.The use of such up-to-date analysis methods and equipment as Qemscan and Mineral-C7 allows one to determine minerals size, liberation degree, and mineral associations. Mineralogical data can reveal reasons for hard processing of minerals prior to development of the process.The advanced process mineralogical methods used to study Cu-bearing pond tailings indicated several factors that influenced development of the process. The first one is a barren size fraction which is to be removed from the process in order to considerably reduce the costs connected with grinding. The second is the presence of films on chalcopyrite surface; in this context, a preliminary attrition of the material was recommended. The third factor is finely disseminated Cu minerals in sulphide and in the rock, which predetermined selection of particle size for flotation. All these data led to significant decrease in time required to develop the process technology. The developed process flowsheet based on the obtained mineralogical data is present in Figure 1."

Jan 1, 2016

By Robert F. Goss

OCAW appreciates the opportunity given to us by the sponsors of this Conference to present our position and policies on the issue of radiation hazards in mining. Our principal concern is the health impact that the mining of uranium has on our members. OCAW represents 1,500 underground uranium miners and more than 10,000 underground miners with 3,000 in the Rocky Mountain region. The U.S. Public Health Service has determined through mortality studies that the number one cause of death among uranium miners is lung cancer. It was also determined that exposure to radon daughters and mine dust correlates with the lung cancer experience of uranium miners. Data from the U.S. Mine Safety and Health Administration has also shown that not only uranium underground miners, but all underground miners, are exposed to radon daughters -- especially underground miners in the Rocky Mountain region. It is our position that any OCAW underground miner is at potential lung cancer risk. The dosages of radon daughters that our miners are exposed to are very many times the background levels of radon exposures in the communities where they live. We are also aware that cigarette smoking accelerates the onset of lung cancer; however, it has to be clear that the available scientific evidence shows that alpha radiation does initiate lung cancer and that cigarette smoke, as a recognized co-carcinogen, promotes cancer already initiated by radiation. It is true that cigarette smoke increases the risk of cancer significantly for miners exposed to radon, but nonsmoking miners have experienced lung cancer rates twice as high as the comparable members of the U.S. population. OCAW's position is that the occupational regulatory agencies should concentrate on the exposures that can be controlled; that is, occupational exposures rather than life-style exposures. Our Union has maintained a consistent posture in relation to carcinogens in the workplace -- that is, exposure to cancer-causing agents should be limited to the [lowest feasible level]. OCAW has interpreted lowest feasible level as the lower limit of detection of the collection and analytical method used to detect the carcinogen. Our posture is based on the available scientific information on carcinogenesis. We have asked the scientific community, many times, to provide us with safe levels of exposure to carcinogenic substances, including radon daughters. The answer has been: "We cannot determine levels of exposure low enough to assure that no cancer will occur." In short, there is not a "safe threshold" for any carcinogen. This statement does not come from one of the few so-called "pro-labor scientists," it comes from the National Cancer Institute and the National Institute for Occupational Safety and Health. I don't need to be a scientific sage, then, to conclude that the lowest level of exposure corresponds to the lowest risk of developing cancer. That is, then, our policy on exposure to carcinogens. It seems there has been an attempt to ignore the fact that lung cancer in uranium miners is the principal cause of death. Uranium miners are no exception from workers exposed to carcinogens. Our policy applies to them. Uranium miners should be exposed to the lowest feasible level of radon daughters and any decrease in the permissible exposure level is a decrease in their lung cancer risk. Accordingly, OCAW has petitioned the Department of Labor for a new permissible exposure limit to radon daughters in uranium mining, which lowers the current exposure standard from 4 Working Level Months (WLM) per year to 0.7 Working Level Months per year. We made our demand to the Department of Labor on April 20, 1980. We are still awaiting action from the Federal Government on our petition. OCAW is also very concerned with other important health impacts of uranium mining. We are concerned with a rate of disabling accidents and fatalities which is twice as high as the same rate in other underground mines, excluding coal. We are also concerned with the rate of respiratory disease fatalities among uranium miners which is almost four times the rate among a comparable U.S. population. We have expressed those concerns when the U.S. Senate proposed a Federal Compensation Act for uranium miners. That proposal, by Senator Dominici of New Mexico, found a quiet death in two Congressional sessions. In conclusion, our position on lung cancer induced by radon daughters is the same position we have taken with all other industrial carcinogens: The lower the exposure, the lower the risk. OCAW is demanding a drastic decrease of the permissible exposure limits. OCAW will never accept that a segment of our membership which mines uranium should take the lion's share of the risk while the uranium mining companies take all the benefits.

Jan 1, 1981

By J. D. Miller, C. L. Lin

In general, x-ray computed tomographic (CT) techniques are able to provide 3D images of the internal structure of opaque materials in a nondestructive manner. The unique cone beam geometry allows acquisition of all 2D projections with only one rotation of the sample thus providing for fast data acquisition and better x-ray utilization, as a complete 2-D detector array receives the cone-shaped flux of rays. Thus, an isotropic 3D volume can be reconstructed without the mechanical translation and the stacking of sequential slices as is the case for more conventional CT scanners. In this regard, a state-of-the-art, custom designed xray microtomography facility to provide very detailed 3D spatial analysis of multiphase particles has been installed and is in operation at the University of Utah. The reconstructed 3D tomographic volume allows for an adjustable spatial resolution from 5 to 20 microns for sample dimensions from 10 to 40 mm in diameter, respectively. Utilization of this custom designed cone-beam x-ray microtomography system is discussed. Applications described include: coal washability analysis for the design and operation of coal preparation plants, liberation analysis for evaluation of grinding practice and separation efficiency, mineral exposure analysis for prediction of the ultimate recovery from heap leaching operations, and analysis of the pore structure network of packed particle beds for simulation of flow through such porous structures as encountered in filtration and heap leaching.

Jan 1, 2003

By R Jia, J T. Waldram

"The Caijiaying lead zinc mine is located in China, north-west of Beijing, in Hebei Province. The region experiences severe winters, below -35°C, and warm summers, up to 30°C. The mine and concentrator commenced operations in the second half of 2005 with a conventional tailings disposal system consisting of a tailings dam with peripheral ring main discharge and central water recovery. A second similar dam sharing one common wall was added later. In view of the extreme winter conditions tailings lines and ring mains plus spigots, together with return water lines, require insulation and electrical trace heating. The volume of process water trapped as ice in the tailings dam ponds each winter is significant. This seasonal variation presents a major difficulty in the management of process water availability. Although Caijiaying is an underground mine there was no backfill plant at the start of operations. As plant throughput increased more quickly than originally anticipated, tailings storage capacity became a prime concern. The construction of a backfill plant in 2007 reduced the pressure on surface tailings storage area requirements, but as suitable land on which to construct further tailings storage was both expensive and difficult to acquire, a more efficient use of the available area was required. Dry tailings storage, where flotation tailings are filtered to provide an immediate return of process water plus ‘dry’ tailings filter cake for stacking, provided an answer to both the land area required, and the water management difficulties. The paper details the reasoning behind the change and the benefits obtained at Caijiaying by moving from ‘wet’ tailings storage to ‘dry’ tailings storage.Citation:Waldram, J T and Jia, R, 2016. Caijiaying Dry Tailings Storage, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 379–382 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By M A. Noppé

"Investors and other stakeholders assessing the risk, opportunity and relative value associated with a resource project need to appreciate the project in its correct context. Errors, omissions, biased reporting or conflicting information in project reporting may lead to a misinterpretation of technical and financial results, resulting in biased estimates or assumptions on project value.This paper provides a simple ‘Resource Project Framework’ for presenting a project’s status that may be readily benchmarked against other similar projects and to illustrate the stages required to advance the project outcomes to higher levels of certainty. The framework draws on definitions and guidelines readily available in various resource industry reporting codes and public company reporting requirements.The framework assesses three key areas for placing a resource project in its correct relative context, namely:the project development stagethe confidence in the Exploration Results, Mineral Resources and/or Ore Reservesthe level of accuracy, precision and confidence in the technical and economic studies supporting the reported results or options for the project.The application of the Resource Project Framework is illustrated using two project examples, one from publicly reported company project releases and the other for two development projects.CITATION:Noppé, M A, 2016. A framework for presenting and benchmarking resource projects, in Proceedings Project Evaluation 2016, pp 260–274 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By J Eberhard, C Paton, J Bennett, C Baillie, A Melland, J F. Clewett, T Newsome

A central aim of rehabilitation is to ensure that disturbed land is returned to a post-mine condition that is safe, stable and self-sustaining. This paper describes initial results from a grazing trial at the New Acland open-cut coal mine in southern Queensland (-27.27 lat, 151.72 long) that aims to assess the sustainability and viability of cattle production from rehabilitated mined land compared to production from surrounding unmined lands (Newsome 2014). The grazing trial was established in 2013 by the Acland Pastoral Company, a subsidiary of New Hope Coal, on lands previously used for dairying, beef and crops before open cut coal mining of the Walloon coal measures began in 2002. The area has a mean annual rainfall of 640 mm. Local soils, typically dermosols and vertosols derived from sandstones or overlying basalt flows, are suited to grazing but are marginal for cropping.CITATION:Clewett, J F, Newsome, T, Paton, C, Bennett, J, Melland, A, Eberhard, J and Baillie, C, 2018. Sustainable production from rehabilitated coal mine pastures in southern Queensland’s Brigalow Region – Acland grazing trial results, in Proceedings Life-of-Mine 2018, pp 35–37 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By W. J. Maraman, D. R. Harbur, J. W. Anderson

A device for rapidly quenching liquid metals into thin platelets has been developed at the Los Alamos Scientific Laboratory. This rapid quenching equipment is built around the technique of catching a molten drop of metal between a rapidly closing plate and a stationary plate. The design and operation of this unit are described. The closing speed of the smasher plate at impact is 12.6 ft per sec. The quenching rate for this device is controlled by the interface resistance between the plates and the platelet, and is dependent upon the heat content and density of the material being quenched. The initial quenching rate down to the freezing point of the platelet material is lo5º to 106ºC per sec. After an isothermal delay, which is poportional to the heat of fusion of the platelet material, the final cooling rate down to the temperature of the smaslier plates is l04ºto 105cº per sec. RAPID heating of metals by capacitor discharge and other methods has provided the metallurgist with a useful tool for probing into the kinetics of phase changes and the many nonequilibrium phenomena which occur during rapid temperature changes. Equally interesting studies can also be made on metals and alloys which are rapidly cooled from the liquid state.' Studies in this field have been limited, however, because the rates at which metals could be cooled were many orders of magnitude slower than the rates possible for heating. In recent years many new laboratory methods have been developed to rapidly cool metals from the liquid state to ambient temperature and below.2"4 All of these methods involve spreading a liquid drop of metal into a thin foil in a very short time. The methods developed have varied from ejecting a drop of molten metal at the inside surface of a rotating cylinder or stationary curved plate to catching a falling drop of molten metal between rapidly closing plates. The equipment which has been developed at the Los Alamos Scientific Laboratory for rapidly cooling molten materials uses the latter of these two approaches. The basic design, operation, and initial results of this rapid quenching device are given in this report. APPARATUS The drop smasher, which is now being used to obtain rapidly cooled metal foils, is shown in Fig. 1. Basically the device consists of a smasher plate which is driven by a solenoid into a stationary plate. The solenoid is activated by a drop passing through the photoelectric cell and is powered by discharging an adjustable 350-v capacitor bank with a 66-amp peak current into it. This power supply is designed so that the solenoid is powered for 2 m-sec after plate closure to minimize the rebound effect. There is an adjustable time-delay mechanism between the photoelectric cell and the solenoid. Both smasher plates have changeable inserts so that a variety of materials can be used to smash the molten drop. The shaft of the moving plate is guided in an adjustable housing which has ball-bearing walls. The cabinet shown to the left of the drop smasher in Fig. 1 contains the power supply and receiver for the photoelectric cell, the time delay mechanism, and the capacitor bank. The drop smasher can be placed inside a vacuum chamber, for use with radioactive materials, with the upper plate forming the lid, as shown in Fig. 2. On top of the vacuum lid is an induction coil, powered by an Ajax induction generator, which is used to melt drops from the end of the rod extending through the vacuum seal on top the quartz tube. OPERATION The drop smasher shown in Fig. 2 is operated in the following manner. The smasher plates are separated and the unit is lowered into the vacuum chamber using a pressurized cylinder. The induction coil, quartz tube, and lid with sliding vacuum seal are then assembled on top the vacuum chamber. A rod of the material for rapid quenching studies is connected to the rod extending through the sliding vacuum seal. The vacuum chamber is then evacuated and the desired atmosphere established. The photoelectric cell is turned on, and the capacitor bank is charged and armed. Power is supplied to the induction coil, and the rod of material for rapid quenching studies is lowered into the induction field. A molten drop forms on the end of the rod, drops off, falls through the light beam of the photoelectric cell, and is then caught between the smasher plates. .

Jan 1, 1970

By EDWARHD HALSE

Discussion of the Paper of Dr. H. M. Chance, presented at the Lake Superior Meeting, September, 1904. EDWARD HALSE, Puerto Berrio, Colombia, So. Amer. (communication to the Secretary*) : The Taviche mining-district is generally known as a Taviches," being named from the two villages called respectively San Pedro Taviche and San Jeronimo Taviche. It is so called by José G. Aguilera, in his paper on the Geographical and Geological Distribution of the Mineral Deposits of Mexico;' and in published reports by the late N. W. Rudston Read ;2 and by Juan de Dios Villarello.3 The region is a large one, measuring about 24 miles long and 7 miles wide. Dr. Chance, in his interesting paper, tells us very little about the nature of the ores, and, with regard to the geology of the district, contents himself with observing that ? the country, as a rule, consists of eruptive rocks; and no evidences of sedimentary strata appear near the mines.? The latter part of the above statement is hardly correct. The formation is mainly eruptive, being hornblende-audesite of Tertiary age, which is limited on the east by the calcareous (Cretaceous) formation, and on the west by the Huronian rocks of Ocotlan. Limestone is seen close to the Santa Càtarina mine, at the northern end of the region. In the surface-working known as La Cueva, a little northeast of San Pedro, limestone forms the eastern wall of the deposit which consists of spots (moscas) of pyrargyrite in white opaque or transparent quartz. Ill one place the ore is associated with stibnite, and the quartz frequently exhibts a

Sep 1, 1905

By G. S. Hume

Production of petroleum and natural .gas increased in Canada in 1940 over the previous year. Alberta produced more than 97 per cent of the total Canadian production of 8,718,053 bbl. of oil, an increase for this province of nearly 12 per cent, whereas in Ontario and New Brunswick, where the production is relatively small, there was a slight decline. In Alberta the main producing field is Turner Valley, on the eastern edge of the foothills southwest of Calgary, and development continued in this field in 1940 with the completion of 36 wells, all of which obtained production. In the Red Coulce field, close to the International Boundary, near Coutts, no new wells were drilled and the seven producing wells showed a decline of 900 bbl. below the previous year. Also, in the Wainwright field of east central Alberta, four wells, yielding heavy crude oil, produced 4000 bbl. less oil than in 1939, owing possibly rather to discontinuous operation than to actual decline in potential yield. This decline was more than offset by production from a new field 40 miles northeast of Wainwright, at Borradaile, producing oil of 14" to I 5° A.P.1. There was a small increase in production during 1940 from the Del Bonita field, in southern Alberta, where the production is from two wells. The outstanding development of the year was the completion of Standard Oil Princess No. 2 well in the Steveville area, on the Plains 100 miles east of Calgary. This well was completed late in December with an initial flow1 of 520 bbl. of 26.3" A.P,I. oil, and 12,750 M cu. ft. of gas from the upper part of the Mississippian limestone. It has opened up a new field and given a further proof of the potentialities of the Southern Plains. The production of petroleum in Canada is shown in Table I. Since most of the yield comes from Alberta, the production is shown from the various fields in Table 2. The sale value of the petroleum produced in Canada in 1940 exceeded 11.1 million dollars, which is still somewhat less than the value of the natural gas production, shown in Table 3. Table i.—Production of Petroleum in Canada" Barrels Province 1939 1940 New Brunswick........ 20,101 21,161 Ontario............... 206,196 186,471 Alberta............... 7,595,000 8,493,237 Northwest Territories. . 17,013 8,493,23717.184 Total............... 7,838,310 8,718,053 Value............... $10,353,351 $11.113,000 0 Bureau of Statistics, Ottawa. Turner Valley, Alberta Turner Valley continues to be by far the largest producing field in Canada (details are given in Table 4), The limits of the Pr in- field are now Known. On the east the oil area is bounded by the gas cap, which in turn is cut off on its east side by a major overthrust fault; on the west, ii is defined by edge water at a level of 4roc

Jan 1, 1941

By G. S. Hume

Production of petroleum and natural .gas increased in Canada in 1940 over the previous year. Alberta produced more than 97 per cent of the total Canadian production of 8,718,053 bbl. of oil, an increase for this province of nearly 12 per cent, whereas in Ontario and New Brunswick, where the production is relatively small, there was a slight decline. In Alberta the main producing field is Turner Valley, on the eastern edge of the foothills southwest of Calgary, and development continued in this field in 1940 with the completion of 36 wells, all of which obtained production. In the Red Coulce field, close to the International Boundary, near Coutts, no new wells were drilled and the seven producing wells showed a decline of 900 bbl. below the previous year. Also, in the Wainwright field of east central Alberta, four wells, yielding heavy crude oil, produced 4000 bbl. less oil than in 1939, owing possibly rather to discontinuous operation than to actual decline in potential yield. This decline was more than offset by production from a new field 40 miles northeast of Wainwright, at Borradaile, producing oil of 14" to I 5° A.P.1. There was a small increase in production during 1940 from the Del Bonita field, in southern Alberta, where the production is from two wells. The outstanding development of the year was the completion of Standard Oil Princess No. 2 well in the Steveville area, on the Plains 100 miles east of Calgary. This well was completed late in December with an initial flow1 of 520 bbl. of 26.3" A.P,I. oil, and 12,750 M cu. ft. of gas from the upper part of the Mississippian limestone. It has opened up a new field and given a further proof of the potentialities of the Southern Plains. The production of petroleum in Canada is shown in Table I. Since most of the yield comes from Alberta, the production is shown from the various fields in Table 2. The sale value of the petroleum produced in Canada in 1940 exceeded 11.1 million dollars, which is still somewhat less than the value of the natural gas production, shown in Table 3. Table i.—Production of Petroleum in Canada" Barrels Province 1939 1940 New Brunswick........ 20,101 21,161 Ontario............... 206,196 186,471 Alberta............... 7,595,000 8,493,237 Northwest Territories. . 17,013 8,493,23717.184 Total............... 7,838,310 8,718,053 Value............... $10,353,351 $11.113,000 0 Bureau of Statistics, Ottawa. Turner Valley, Alberta Turner Valley continues to be by far the largest producing field in Canada (details are given in Table 4), The limits of the Pr in- field are now Known. On the east the oil area is bounded by the gas cap, which in turn is cut off on its east side by a major overthrust fault; on the west, ii is defined by edge water at a level of 4roc

Jan 1, 1941

By AIME AIME

Annual net production of crude oil from the Anglo-Iranian, Oil Company's fields in Iran for the years 1940 through 1945 amounted to: YEAR TOTAL PRODUCTION (Long Tons) 1940 8,626,639 1941 6,605,320 1942 9,399,231 1943 9,705,769 1944 13,274,243 1945 16,835,000 (preliminary figure) All developed fields were on almost continuous production throughout the war, though their operation naturally was hampered by war conditions, which affected particularly supplies of equipment.

Jan 1, 1946

By Edward W. Parsons

The explosive-anchored rockbolt was field tested in six mines where rock conditions varied from incompetent shale or mudstone through fairly soft sand-stone to firm sandy shales. The purpose of the testing was to document, under a wide variety of conditions and in comparison to other rockbolt anchors, the quality of the anchorage produced by the explosive-anchored bolt. In addition, the length, strength, and design of the explosive charge necessary to produce positive anchorage up to the yield strength of the weakest component of the bolt were determined. A l4-inch length beaded explosive charge was found to be suitable, in general, in relatively weak strata, and the length can be reduced in more competent strata. Of the 127 explosive?-anchored bolts tested, 118 bolts produced an evaluated anchorage in excess of 17,000 pounds. Only 4 of 43 expansion-shell bolts and 4 of 14 wedge bolts produced anchorage this good. In preliminary tests, properly coupled explosive-anchored bolts did not ignite an explosive gas mixture. Some minor phases included in the investigation were as follows: (1) effect of explosive-anchored rockbolt on surrounding rock; (2) effect of time on anchored bolts based on torque tests; (3) effect of submersion in water on rockbolt anchorage; (4) pull tests to higher loads; and (5) ignition tests.

Jan 1, 1965

By Barrick Pierina, John Frostiak, Igor Gonzales, Kenneth G. Thomas, Ken Manning

"1.0 SummaryThe Pierina deposit was acquired in August 1996 when Barrick Gold Corporation purchased Arequipa Resources, a junior mining company with extensive land positions in Peru. At the time of acquisition, Arequipa had developed two exploration tunnels and drilled 9 exploration holes on the property. Metallurgical tests, conducted on samples taken from the tunnels and the exploration holes indicated that the ore was amenable to heap leaching. Barrick’s exploration team recognised from the outset, the potential of the mineralisation and convinced Barrick’s senior management that this was indeed a world class deposit that should be pursued. On November 25, 1998, the first dore was poured at Pierina, 27 months from the time of acquisition. During that period Barrick completed its exploration programme, prepared a development plan including capital and operating costs, production profiles and cash flow forecasts, and a schedule to develop a mine and construct a leach pad and gold recovery plant, including all supporting infrastructure. All permits and environmental approvals were obtained and all necessary land was acquired. The project was completed on schedule and under budget. This was the first greenfield mine development for Barrick outside of North America.This paper details, mainly, the research and development, engineering, construction and commissioning of the metallurgical process facilities.2.0 The Develonment ProgrammeImmediately after the acquisition, Barrick began the process of gathering information required to prepare a project development plan. Kilborn Engineering was retained to assemble all of the information collected and collated into a development plan document. This document was completed by June 16,1997. The objective was to bring the mine into production as quickly as possible with critical activities identified as follows:"

Jan 1, 2000

By Frederick Laist

I AM APPRECIATIVE of the honor you have done me in electing me to membership in your Society. I value the contacts with men of imagination and ideals which this implies. I am grateful for the recognition of such small contributions as I may have made, or helped to make, to the vast fund of scientific and engineering knowledge. We like to think, as we grow older, that our lives have not been purely parasitical, and that through our efforts some forward step, however small, has been taken toward improving conditions under which we live and do our work. In these days of industrial depression, we hear much criticism of our "machine age." Modern engineering, mass production, the complexity of our lives, all come in for some share of blame. The farmer is said to have been spoiled by the tractor and the gang plow, the factory worker has become a slave of the assembly conveyor, the scientific worker is no longer free but has sacrificed much of his individuality to the research organization of which he is a part. We wonder whether our work as engineers has been worth while and whether our striving after more efficient ways of doing things has been a curse to mankind rather than the boon we thought we were conferring.

Jan 1, 1932

By Zhou Jun

Water-quenched samples were taken from a commercial flash furnace at three levels along its reaction shaft during operation at high feed rate. The samples were subjected to a series of analysis and observation. Such processes of the feed in reaction shaft as oxidation, desulfurization, melting, slag and matte formation and etc., variations of particle size along axial and radical direction of the shaft are investigated. The following smelting mechanism in reaction shaft named as “Multi-particle and multi-phase fusion model” is proposed: (1) Fragmentation and collision of concentrate particles take place simultaneously in reaction shaft with particle size growing up. Collision produces large-size “unit melt” which falls into the reaction layer in the settler bath. (2) In the settler reaction layer below the shaft, weak bath smelting reactions take place among the shaft products, producing final matte and slag which separate into two layers. (3) The processes in the shaft are all progressive along the whole height of the shaft. The predominant reaction in the shaft is oxidation, not reduction.

By Jean-Pierre Côté, Alexandre Noiseux

"Hatch and ArcelorMittal Mines Canada have combined their expertise to develop a dynamic model of the latter’s Iron Ore Pellet Plant in Quebec, Canada. This model was used to predict the benefits of different expansion projects, as well as asses the best implementation sequence.Two modelling tools were used: a discrete-event simulation software used to develop the dynamic model of the Pellet Plant and an in-house process simulator. The latter was based on operational data and known behavior of the process, and was calibrated with historical data gathered under different operating conditions.The results of the process simulator were used as input values for the dynamic model, which included all of the operation steps of the pelletizing process, from concentrate beneficiation to baking of the pellets. The model has been validated by assessing its capacity to represent adequately the operation of the plant during a 20-month operating period. It was able to reproduce the plant capacity within a precision of 1.2%.Simulated “what-if” scenarios allowed quantifying the production increase associated with the addition of new equipment such as ball mills or balling discs, implemented individually or in combination. Results revealed a potential 10% increase in the annual plant production by adding additional equipment in the two most limiting sectors of the plant, grinding and agglomeration. The simulation results made it possible to quantify the synergistic effect of two projects on plant throughput; the model showed that the combination of two projects resulted in a greater production increase than the sum of the same projects evaluated individually.Now that it has proven reliable, the simulation tool can readily be used by ArcelorMittal Mines Canada process engineers to perform simulations for equipment optimization, and to evaluate the impact of various operating parameters such as equipment availability and tonnage, product mix or concentrate quality. This work showed that a reliable model can be developed based on known parameters in combination with the proper integration of the process knowledge."

Jan 1, 2010

By R A. M Maddever, P Jeanneau, V Flahaut

Over the entire life cycle of a mine, from early resource evaluation to the blasting of benches, the collection of geochemical data is crucial for the site operator, who must routinely and intensively drill and sample the orebody. This produces huge numbers of physical samples, in turn requiring significant cost and time for their preparation and assay. Moreover, despite best efforts, the sample recovery process is prone to error, which limits the quality of data.The pulsed neutron gamma technique has been used for decades in various industries, in particular oil logging, for its ability to provide direct identification and quantification of elemental concentrations. However, its implementation in logging tools for the mining sector is relatively recent. Built around the latest in technology for optimal spectrometric measurement, a commercial tool referred to as FastGrade™ 100 has been available for a few years and used with increasing success in the mining environment, specifically the iron ore industry, resulting in a reduction in the amount of collected samples. Relying on the physics of neutrons and gamma photons, both of which are particles that penetrate the surrounding bedrock through several tens of centimetres, such spectroscopy tools measure in real-time the composition of a much larger volume than the delimited volume of the drilled material traditionally used for geochemical mapping. Better statistics and reliability of the estimated composition increase the ability to properly and quickly measure drilled holes and allow the substituting of all or part of the sampling and assaying efforts by geochemical log data. Our paper focuses on this technology, known as pulsed fast and thermal neutron analysis (PFTNA). It reviews the main drivers for the design of such a logging tool and discusses how the fundamental characteristics of the technology, in terms of neutrons and gamma interactions, translate into interpretation of the analytical output.CITATION:Jeanneau, P, Flahaut, V and Maddever, R A M, 2017. Iron ore benefits from neutron pulsed geochemical tools, in Proceedings Iron Ore 2017, pp 387–396 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

DCF Valuations are very important to individuals and companies involved in the mining industry. Such valuations are critical to investment decisions in relation to new and existing projects. In particular they provide fundamental information to shareholders in the event of a capital raising or takeover and to financiers supporting mining companies and projects. Also, DCF Valuations are often used to support asset carrying values in the financial statements of mining companies. This paper presents a Chartered Accountant's (CA's) perspective on the main issues to be considered in preparing, analysing and relying upon DCF methods in mineral valuations and provides some practical examples relating to key issues. The paper makes the important point that DCF methods involve making assumptions about future events and circumstances that inherently contain uncertainty which results in a valuation prepared on a DCF basis providing a range of values that are not perfect or accurate. In order that DCF valuations provide meaningful information the underlying methodology used and assumptions made must be consistent, sound and well supported. Credibility of those involved in preparing mineral valuations is vital and this paper supports the adoption of sound practices by all concerned.

Jan 1, 1994

By Yuexin Han, Mu. Yufan, Yanjun Li, Peng Gao, Yongsheng Sun

"The objective of this study was to evaluate the effect of reduction temperature, reduction time and binary basicity on the size of metallic iron particles in coal-based reduction products of an oolitic iron ore. The particle size distribution behavior (i.e., cumulative passing percentage and mean size of metallic iron particles) during reduction was investigated in detail. Results showed that the particle size distribution of metallic iron particles was strongly influenced by reduction temperature, reduction time and binary basicity. The cumulative passing percentage and mean size significantly increased with reduction temperature and time in the entire range of the experiments. All curves of cumulative passing percentage versus particle size under different conditions demonstrated a similar trend (continuous increase). The size distribution parameters and mean size slightly increased with increasing binary basicity and significantly decreased when the binary basicity exceeded 1.0. The size of metallic iron particles could be controlled by adjusting the reduction conditions during coal-based reduction.IntroductionThe increasing demand for iron ore coupled with diminishing high-grade iron ore reserves has resulted in the urgent need for innovative technologies in order to use refractory iron ores. Oolitic iron ore is a typical refractory iron ore with tremendous abundance globally. Based on published literature, oolitic iron ore reserves are approximately 140 million tons in Europe, 10 billion tons in China and 66 million tons in Pakistan (Kazmi and Abbas, 2001; Wu et al., 2011; Yu and Qi, 2011; Sun et al., 2013a). Therefore, the efficient exploration and use of oolitic iron ore resources can play a significant role in easing the mineral resource crisis in the iron and steel industry. However, oolitic iron ore cannot be effectively upgraded by traditional beneficiation methods due to its mineralogical characteristics (e.g., low grade of iron, poor liberation of iron minerals and high phosphorus content) (Li et al., 2011b; Sun et al., 2013b).Researchers recently proposed coal-based reduction followed by magnetic separation to recover iron from refractory iron ores (especially oolitic iron ore) and a certain degree of breakthrough was achieved in both theory and practice. In this technology, iron minerals in the ore are directly reduced by coal to metallic iron, which grows into particles of different sizes. After comminution and liberation, metallic iron is concentrated by magnetic separation (Srivastava and Kawatra, 2009; Sun et al., 2013a; Li et al., 2011b; Sun et al., 2013b; Li et al., 2011c; Gao et al., 2013). Sun et al. and Gao et al. used this technology to examine the recovery of iron from oolitic and Bayan Obo iron ores, respectively (Sun et al., 2013a; Li et al., 2011b; Li et al., 2011c). Metallic iron powder with more than 90% iron content was obtained as the final product, which could be used directly in steel production."

Jan 1, 2015