Search Documents

By C B. Smith, G L. Boxer, S W. Moss, A L. Jaques, V Lorenz, M J. Rayner

The Ernest Henry Iron Oxide Copper Gold deposit is hosted in a large dilation between two moderately dipping shear zones found in the footwall and hanging wall of the deposit. These shears are controlled by a large diorite intrusion to the north-east and south-west of the deposit, formed ~1660 Ma. A shear zone dubbed the ‘Interlens’ uncovered through underground workings truncates the main orebody into two lenses, and is hypothesized to have formed in conjunction with the Hanging Wall Shear Zone and Footwall Shear Zone. All three shears dip moderately to the SSE (50–140) from open cut exposures through to the current mining horizon approximately 800 m below the surface. Routine geological work and a capital drilling campaign has identified a significant flexure in these sub parallel ore bounding shears with increasing depth. A shift in shear orientation in the Interlens over approximately 100 m vertically from ~50° to the SSE to a steep, easterly trend (~85° to the east) is observed in both drill core and exposures in the underground workings. It is hypothesized the diorite intrusive to the south-west of the deposit controls the shear zone geometries at depth. The geometry of the Interlens mirrors the surface expression of the Proterozoic package of the orebounding shears to the south-west of the deposit, suggesting the surface geometries of the shear zones are consistent with depth. Additional drilling to explore the validity of this hypothesis is planned for the near future to better understand the structural controls on the Ernest Henry mineralisation with increasing depth.

Mar 22, 2022

By Ronald B. DeDiemar

This paper will present the intrinsic factors of a cone crusher that affect performance, develop and define an ideal feed gradation for a cone crusher and, finally, bring out an important new development in computer design of crushing chambers and show an ability to predict crusher performance without trial-and-error methods.

Jan 1, 1979

By T N. Little

This review paper presents an integrated and practical insight to blasting geology and its importance. This approach involves developing blasting objective up front and implementing geology specific blast designs. The author refers to this approach as ‘starting at both ends’. There are many human-imposed controls on blasting operations, such as: safety, security, legislative, company standards, heritage, and environmental constraints. Thus it is possible for some operators to lose sight of the controls imposed by nature. This paper demonstrates how site geology controls or influences many aspects of the rock breaking processes and how a focus on this aspect has potential to add considerable value to mining operations. It is obvious that mining companies concentrate their efforts on economic/ore geology (good rock geology). However it is the author’s experience that they also concentrate on engineering geology (bad rock geology) only when forced to do so by the ground conditions, but seem to run out of puff before they apply blasting geology (big rock geology). This paper contains five main sections. In the first section, the impact of geological controls on blasthole drilling is briefly discussed in terms of drill selection, penetration rates, bit wear, blasthole stability, blasthole deviation, and health precautions. In the second section the geological controls on aspects of geometric design are reviewed. These include: hazardous minerals, valuable minerals, selection of the blasting techniques, geological structures, blasting direction, and blasting geometry. Section three overlaps with the geometric design section and deals with aspects related to explosives. Topics addressed include selecting the explosive type based on geology, distribution of explosive charge in space and time, explosive performance, and the rock response to explosive loading. In the fourth section, examples are given of the operational complexity needed to implement a blast to cater for difficult bench geologies, environment constraints, past mining (voids) and need for a high degree of quality control. Section five demonstrates geological controls on blast results. Blasting results include the muck pile characteristics, downstream handling and processing, damage to the remaining rock, and blasting emissions.

Nov 8, 2011

By Walisson Silva Gomes

A injeção de carvão pulverizado pelas ventaneiras dos altos-fornos é um dos meios de redução de custos de produção do ferro gusa. Esta injeção deve ser de forma efetiva para evitar possíveis desperdícios de combustível. Esse trabalho teve como objetivo desenvolver uma metodologia de quantificação do teor de carbono na lama e no pó de coletor, gerados na limpeza de gás do alto-forno para auxiliar a avaliação da eficiência de queima do carvão injetado pelas ventaneiras e sua correlação com as variáveis de processo. Nenhuma norma especifica a quantificação de carbono na lama e no pó de coletor. Foram utilizadas duas técnicas de quantificação de carbono em carvão e coque utilizados na Companhia Siderúrgica Nacional, a Análise Imediata, baseadas na norma ASTM D 5142-09, e a Análise Elementar. Um estudo mais detalhado para investigar as possíveis interferências nesses métodos de análise, devido a diferença de resultados entre eles, foi utilizado Difração de Raio-X, associado ao método de Rietveld, e Analise Termogravimétrica de Calorimetria Exploratória Diferencial (TG-DSC). A partir dessas análises foi possível definir o melhor método para quantificação de carbono no pó de coletor e lama de alto-forno.

Aug 17, 2017

By De-Qiu Fan, H. Y. Sohn, Y. Mohassab, M. Elzohiery

A novel flash ironmaking process is under development at the University of Utah. A computational fluid dynamics (CFD) approach, coupled with experimental results, was developed for the analysis of the kinetics of reduction of hematite concentrate b yH + CO mixtures at 1150–1350 °C in a droptube reactor.

Mar 1, 2017

By John Hanna

The Mineral Resources Institute (MRI) has developed a unique process for selective fatty acid flotation of phosphate minerals from siliceous ores. The process takes advantage of preferential adsorption and high reactivity of fatty acid collectors towards apatite over silica surfaces under slightly acidic conditions of pH 5-6.5. The process was successful in upgrading various phosphate samples from Florida and North Carolina containing 7.7-15.3% P205 and 62.3- 77.2% Insol to concentrates assaying 28.1-33.1 % P205 and 4.1-9.9% Insol with high P2O5 recovery of 81.8-92.2%. Depending on the type of silica impurities present one or more cleaning steps, with or without sodium silicate, would be required to improve the grade of the rougher phosphate concentrate.

Jan 1, 1992

By I. Sedat Buyuksagis, Jamal Rostami, Ali Naeimipour

"Improving the safety of underground openings and optimizing ground support systems requires reliable ground characterization. This includes understanding the joints, discontinuities, and rock strength. Joint information can be obtained from borehole cameras, but measuring in-situ rock strength is very difficult. Use of borehole probes can be an ideal and efficient way to meet this requirement. This paper discusses the development of the Rock Strength Borehole Probe (RSBP) and presents the preliminary laboratory/field test. This device can be an accurate, flexible, quick, non-disruptive, and cost-effective alternative to estimate the rock strength inside boreholes in underground mines and tunnels. In addition, the scratch testing procedure in the laboratory by means of a newly developed miniature linear cutting machine is explained. Based on the results of these tests, two equations are developed to estimate the uniaxial compressive strength (UCS) and Brazilian tensile strength (BTS) of the sedimentary/metamorphic rocks. These equations, are based on testing 27 different sedimentary, igneous, and metamorphic rocks by full-scale scratch tests, including the cutting tests by a miniature disc. The results show a good correlation between the normal force and the compressive strength of sedimentary rock if the depth of the scratch is known. No significant correlation was observed for igneous rocks, due to the impacts of grain size.INTRODUCTIONEstimated rock mass properties are essential input for geomechanical studies and stability analysis for any structure constructed in or with rock. The availability of geological information is the crucial component of rock mass classification. One of the important parameters in evaluating rock mass properties is the intact rock strength. This parameter is usually measured by testing the core samples, obtained from exploration boreholes. These samples are subsequently tested in geomechanics laboratories. The test results offer limited information about the rock at the few boring locations despite all the efforts and costs. In addition, these results may not necessarily be representative of the behavior of the rock in the field as the test cannot provide the insitu condition of the ground."

Jan 1, 2016

By Bruno Wartchow Laidens

Massas de reparo à quente de sede de válvula e de plugue em panela de aço são utilizadas a fim de se aumentar a vida útil dessas peças, as quais necessitam longo tempo para a troca. Isto propicia um ganho considerável na campanha da panela. O objetivo do presente trabalho foi a caracterização técnica das massas refratárias, bem como a seleção da massa mais adequada para utilização na panela de aço na Usina Rio-grandense. Uma massa magnesiana e duas aluminosas (concretos) foram analisadas por meio de diversas técnicas, como análise de imagens (lupa eletrônica e MEV), distribuição granulométrica, porosidade, composição química, análise mineralógica, resistência à compressão e teste de tração de aderência entre o substrato e a massa. Os resultados demonstraram que a massa de reparo magnesiana com resina de cura à quente apresentou os melhores resultados de adesão junto às sedes, além de apresentar uma significativa resistência à compressão.

Aug 17, 2017

By B. S. Prosser, K. G. Wallace, A. Akansobe

"This paper describes a ventilation project at the Wassa gold mine in Ghana. Golden Star (Wassa) (GSWL), a subsidiary of Golden Star Resources, owns and operates the mine. Golden Star holds a 90% interest in GSWL, while the Ghanaian Government holds the remaining 10% ownership, earning a 5% royalty on the gross revenue of GSWL’s gold production. Construction of the underground mine began in mid-2015 and pre-commercial production started in June 2016. Commercial production from the underground mine was achieved in January 2017. This paper describes the ventilation studies performed to support the initial development and production at the mine. The initial ventilation design included four, parallel surface exhaust fans. Future designs will include booster fans, new primary fans, and additional connections to surface. The paper describes the long-term ventilation planning goals and expectations as the mine achieves a production of 4,000 tpd with truck haulage to surface.INTRODUCTIONThe Wassa Gold Mine is located in the southern portion of the Ashanti Greenstone Gold Belt in Ghana, northwest of Tarkwa as shown in Figure 1. The mine has been in production as an open pit since 1998, with some minor disruptions, but the surface minable reserves have become exhausted and the mine started a transition to an underground operation in 2015. The underground mine was initially developed with twin decline accesses extending from the base of the open pit to the mining areas. The mining method selected was sub-level open stoping with cemented rock backfill. The original production level for the mine was 2,500 tpd with ore and waste transported by trucks hauling in the ramps to surface. In 2017 the production goal was set to increase to approximately 4,000 tpd. This resulted in an increase in the truck haulage fleet in addition to a significant increase in ventilation requirements. This paper describes the ventilation upgrades at the mine as it transitioned from a surface to an underground operation and the adjustments the ventilation system needed to make in order to accommodate a significant increase in production"

Jan 1, 2019

By Gustavo Henrique Bolognesi Donato

A utilização de materiais cerâmicos em componentes que operam em elevadas temperaturas (p. ex.: trocadores de calor cerâmicos que operam acima de 800°C) é vantajosa do ponto de vista térmico, mas não é trivial em termos estruturais, uma vez que estes materiais são frágeis e portanto, suscetíveis à fratura catastrófica. Considerando a necessidade de materiais resistentes a elevadas temperaturas e que garantam a integridade de aplicações como tais trocadores de calor, este trabalho investiga as propriedades mecânicas da alumina a (Al2O3) como função da temperatura na faixa de 23°C a 850°C. Para tal, cem ensaios de flexão em 4 pontos e ensaios adicionais selecionados em 3 pontos foram realizados em amostras de seção transversal retangular de ~ 45 mm2 produzidas por gelcasting, técnica esta que tem grande potencial para moldar peças de geometria complexa. Os ensaios foram conduzidos empregando um dispositivo fabricado em Inconel (superliga de Níquel-Cromo) especialmente desenvolvido para esta finalidade e contendo articulações objetivando autocompensação de desalinhamentos. Os resultados experimentais puderam ser muito bem descritos usando a estatística biparamétrica de Weibull e demonstram o efeito da temperatura na redução da resistência à flexão. Adicionalmente, o dispositivo proposto facilitou e dinamizou a realização dos ensaios, além de garantir pequena dispersão das propriedades mecânicas obtidas, especialmente se considerado o micromecanismo frágil de fraturamento desta classe de materiais.

Aug 8, 2018

By Michael Alber

Coal mining by the longwall method typically causes seismic events. This paper describes the research on mining induced seismicity around two specific longwalls at 1100m depth under several old longwalls. A local network featuring 21 geophones has been installed, underground core drilling and an extensive rock testing program were executed. A rock mechanical model featuring a multi-layer strata was created for use with numerical analyses. Seismic events were localized and three different event types are described. Focal analyses yielded distinct modes of failure. Those types are explained by different failure mechanisms, namely fault activation, remnant pillar punching and beam failure. The use of rock mass classification, rock mass strength criteria and in situ stresses together with 2D and 3D numerical analyses allows evaluating the findings from seismology approaches. Conclusions are drawn that the orientation of longwall with respect to the major horizontal stress orientation plays an important role in mine induced seismicity.

Jan 1, 2008

By Cary Hirner, David Stacey, William A. Rochford

Design considerations and construction techniques were implemented to address groundwater infiltration from a confined aquifer during the excavation and lining of the Cady Marsh Flood Relief Tunnel. This 3-m finished diameter, 2-km long tunnel was successfully completed cost-effectively in an urban setting near East Chicago, Indiana. The soft ground was mined using a conventional tunnel boring machine with hydraulically actuated flood doors and supported with steel ribs and timber lagging. The tunnel was lined with cast-in-place concrete. Dewatering was implemented in settlement prone, boulder-laden ground in residential neighborhoods during construction to depressurize and partially dewater the aquifer at the tunnel horizon. This paper describes the design decisions and construction methods utilized to mitigate and limit infiltration into the tunnel during construction and operation, as well as manage ground settlement.

Jan 1, 2007

By Felipe Gianiselle

A liga de alumínio AA 7108 é uma liga endurecível por precipitação do sistema Al-Zn-Mg. Componentes da liga 7108 obtidos por extrusão têm sido crescentemente utilizados na fabricação de veículos de transporte terrestre. No presente trabalho foram estudadas as modificações microestruturais que ocorrem durante o tratamento térmico industrial de homogeneização, que precede a extrusão a quente desta liga. Foram utilizadas várias técnicas complementares de caracterização microestrutural, tais como microscopia óptica de luz polarizada, microscopia eletrônica de varredura eletrônica (MEV), espectroscopia de raios X por dispersão de energia (EDS), e medidas de dureza e de condutividade elétrica. Durante a homogeneização ocorreu dissolução parcial de compostos intermetálicos contendo Al, Fe, Zn, Mg e Si, enquanto as partículas de Al3(Zr,Ti) permaneceram inalteradas.

Oct 30, 2017

By Sandin E. Phillipson

"On April 5, 2010 a massive dust-fueled explosion at a longwall mine in southern West Virginia claimed the lives of 29 miners. The mine had experienced large gas inrushes from the floor on two known previous occasions, and natural gas was found emanating from floor fractures behind the longwall shields after the explosion, indicating a likely fuel source for the initial ignition. In succeeding months, another longwall mine operating in the same seam 15 miles away encountered smaller inflows of natural gas that halted production from two different longwall faces. Production was halted at a third longwall mine, 30 miles south of the first, in May 2011, when explosive levels of methane were detected inby the longwall face on the headgate. The same mine was evacuated on March 20, 2014 when a series of floor gas feeders were encountered on the longwall face. A literature review indicated that there has been little documentation or description of these events, and that their size and frequency are unknown. The most significant floor gas inrushes in the United States are believed to have been associated with longwall mining in the Pocahontas No. 3 Seam of western Virginia, in which an estimated 5.8 x 107 ft3 of natural gas was expended from a floor feeder on the longwall face over a two-week period (Aul, pers. comm.).A variety of mechanisms and circumstances are associated with methane emanations from underground mines. Hyman (1987) defined an outburst as a violent, simultaneous release of gas and comminuted rock material into a working face or the interior of a borehole, and indicated that certain soft or fractured coals have a propensity for outburst based on gas desorption rates. In this mechanism, reservoirs of autogenic gas hosted in pockets of soft, crushed coal surrounded by harder coal are released suddenly as confining stress is removed by mining. Hyman (1987) also suggested that highly stressed, relatively gassy coal that is penetrated by mining-induced fractures could be outburst-prone. Clayton et al. (1993) and Ulery (2008) recognized the importance of faults as potential conduits for gas from adjacent strata into coal mines, and suggested that biogenic gas trapped in adjacent strata could migrate into mined coal seams due to a pressure differential. Ulery (2008) distinguished between an outburst and a blower, the latter defined as an event expending a large amount of gas over an extended time period, most often emanating from underlying strata, but without expulsion of coal or rock. Methane feeders are further defined as a subset of blowers that continually expend gas over a long period of time but at a lower rate. Many of the mechanisms discussed by Ulery (2008) relate to geologic features that can impound gas within the seam, releasing a voluminous amount when mining breaches the elastic dike, fault gouge, or other geologic structure that had restricted and compartmentalized coalbed methane migration. Thus, the events discussed in this paper can be described as blowers and feeders. However, detailed geological observations of the three longwall mines discussed in this paper appear to indicate a mechanism that is different from those described by Hyman (1987) or Ulery (2008), in that they did not involve coalbed-sourced gas, and the reservoirs were not hosted by coal seams."

Jan 1, 2016

By N Currey, G Corder, G Becker

"The SUSOP« Framework is a new technique that helps incorporate sustainable development principles and objectives into the design and operation of businesses. Developed through the Co-operative Research Centre for Sustainable Resource Processing, it brings a design methodology to sustainability, similar to what hazard and risk techniques such as HAZOP did for safety.Metallica Minerals Limited (æMetallicaÆ) adopted the SUSOP« framework to help identify opportunities and risks that could directly improve or affect its flagship SCONI (nickel-cobalt and scandium) project. This project has the potential to become the worldÆs largest producer of scandium oxide (æscandiaÆ) which is used in solid oxide fuel cells and strengthens aluminium alloys. Located northwest of Townsville in Queensland, the plant site will be located within the previously mined and partially rehabilitated Greenvale Nickel Mine. By applying the SUSOP« framework through a series of multi-disciplinary workshops and offline analysis, Metallica was able to identify numerous sustainability opportunities and risks. Opportunities were clustered together to form concepts to develop a more holistic understanding of the projectÆs overall potential contribution to sustainable development as well as determine where key risks could be mitigated. Four key concepts were identified: Waste and Water Workforce Community and Enterprise Development Energy and Greenhouse Gases (GHG). Metallica was able to include a range of initiatives that could deliver enhanced environmental, social and community outcomes into their mine development plan. These included measures to reduce reliance on water, reduce the volume of waste, provide local opportunities for training and skilled employment and create support for local enterprise development. These measures also resulted in a significant reduction in the capital estimate of the project.This paper provides an overview of the SUSOP« framework, details its application to the SCONI project and discusses the outcomes that will help establish the projectÆs strong sustainable development credentials and improved business outcomes.CITATION:Corder, G, Currey, N and Becker, G, 2013. Sustainability, made easy - A business improvement case study, in Proceedings MetPlant 2013, pp 259-271 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

By J. M. Bray, R. R. H. Cohen, P. Kiousis, S. R. Al-Abed

"INTRODUCTION Conventional tailing storage and management practices typically utilize engineered facilities, such as ring dikes and valley impoundments. To reduce the environmental costs associated with disposing of mine wastes in tailing storage facilities (TSFs), several beneficial re-use strategies have been developed over the years. For example, thickened tailings have been used for paste backfill. It is common for tails to comprise up to 60% of the material’s total weight and it has been estimated that TSF volumes can be reduced by 60% when using this strategy, (Benzaazoua, et al. 2004). Other beneficial re-use strategies have produced unpaved temporary access roads, hot and cold asphalt, chip seals, self-compacting concrete, and golf course sand traps. This project sampled mine tailings from two different TSFs in Colorado and produced structural concrete that could potentially be used for commercial foundations, sidewalks, and paved roads. The tailings were substituted for the fine aggregates typically found in conventional concrete. The two main objectives of this study were to investigate the structural integrity of the produced concrete samples and the leaching of heavy metals from the resulting concrete. The ratio of tailings to fine aggregate (T/FA) was carefully studied to find if there was a correlation between the substitution rate and the structural integrity. The potential maximum substitution rate was also investigated for the produced concrete specimens. The potential of leaching mining impacted water (MIW) was evaluated by comparing the leachability of the raw mine tailings to the encapsulated tailings by using standard shake extraction prediction tests. MATERIAL AND METHODS Materials The four components that make up the concrete mix design for this project are: cement, coarse aggregate (gravel), fine aggregate (sand and mine tailings), and water. The type I/II ordinary Portland cement (OPC), gravel, and sand came from local cement and concrete companies in Denver, Colorado. Mine tailings were collected from two different TSFs in the Rocky Mountain Region, where Pride of the West TSF in Silverton, CO will be denoted as Site A. The primary metals of interest at the mill site are gold, silver, lead, copper, and zinc. The location of Site B will not be mentioned in this report due to confidentiality agreements with the mining company"

Jan 1, 2016

By J. Torma-Krajewski, C. Hipes

Although many mining companies apply ergonomic principles, it is usually done either informally and/or reactively. An example of an informal approach is replacing worn equipment (such as seats) with models that have ergonomic features. Another example is modifying a task to eliminate safety hazards. Such approaches reduce risk-factor exposures that can lead to musculoskeletal disorders (MSDs). A reactive approach is followed when modifying a task/ equipment after an MSD occurs. However, neither of these approaches involves a systematic method of proactively applying ergonomic principles to actually prevent injuries or illnesses. This paper discusses how Vulcan Materials Company applied ergonomic principles and implemented interventions to reduce risk-factor exposures.

By M. Shabbir

A study was made to determine the optimum conditions for precipitation of uranium from mill solutions using hydrogen peroxide. Precipitation tests were made on both synthetic and actual mill solutions. Parameters studied included amount of hydrogen peroxide, initial pH, reaction pH, time, and temperature. Also investigated was the effect of varied amounts of vanadium, molybdenum, and sulfate in the test solution on uranium precipitation and product quality. The optimum conditions for complete precipitation and high product quality were (1) the use of 150 percent of the stoichiometric requirement of hydrogen peroxide, (2) initial pH of 1.0, (3) reaction pH between 3.4 and 5.0, (4) 4 hours reaction time, and (5) ambient reaction temperature. The excess hydrogen peroxide requirement is partially dependent on the amount of impurities present in the feed solution. The hydrogen peroxide process appeared applicable to treatment of the several mill eluate and strip solutions tested. The experimental studies also indicated that the hydrogen peroxide technique gives substantially better product quality than that produced by ammonia precipitation.

Jan 1, 1974

By Jonathan Taylor, Irwan Halim, Frederick (Rick) Vincent

The new underground facilities for the LINAC Coherent Light Source project at the Stanford Linear Accelerator Center in Menlo Park, CA, are constructed in very weak sedimentary rock interspersed with uncemented zones. In addition to several 21-footwide (excavated) tunnels, the NATM excavations include a large, 49-foot wide (excavated) cavern, an unprecedented size in this geology. The critical design issues include characterization of the weak rock, some shallow rock cover areas, and very stringent criteria for final invert slab movements within the tunnel. The design also incorporated severe seismic criteria, since the site is in close proximity to the San Andreas Fault.

Jan 1, 2007

By Nabil F. Ismael, Khalid Farraj

"The axial load transfer along large diameter bored piles in very dense silty sand was examined by field tests. Two instrumented piles 1.2 m diameter and with embedded length of 18 m and 25 m were load tested in axial compression to failure in connection with the construction of a big tower building in Kuwait City, Kuwait. Instrumentation included vibrating wire strain gages at various levels, displacement transducers and extensometers. The purpose being to measure the axial load distribution, skin friction, and base resistance at various load levels. In addition the settlement of the piles and the elastic compression were monitored. The ultimate pile capacity, side friction, and base resistance were determined and correlated with the Standard Penetration Resistance values as determined from the boreholes. Most of the load was transferred as side friction and the pile settlements at the maximum loads ranged from 1.6% to 2.2% of the pile diameter.INTRODUCTIONLarge diameter bored piles are used with increasing frequency for heavy structures in Kuwait and the Gulf region in calcareous sand. The behavior of short piles ranging in depth from 8 m to 15 m was examined by field test (Ismael 2012). However, larger diameter and deeper piles are being used more frequently, including the project described in this paper which included piles with 1.2 m diameter and 18 m to 25 m depth. The design of these piles requires knowledge of the skin friction and point resistance in these soils. While field tests on driven piles are available (Ismael 1989, Ismael 1999), field test data on long large diameter piles installed through very dense sands or silty sands are very limited at present. The results of two load tests carried out recently on instrumented bored piles at one site in downtown Kuwait City have become available. In these tests the failure load was extrapolated from the test results. It is important to examine and analyze the test results for the benefit of the geotechnical research and design engineers."

Jan 1, 2017