Search Documents

By V. Vakiloroaya

The paper aims at developing a hybrid solar-assisted air conditioner system for performance enhancement and energy efficiency improvement. To increase sub-cooling of the refrigerant at partial loads, we propose a new discharge bypass line together with an inline solenoid valve, installed after the compressor to regulate the mass flow rate of the refrigerant vapour passing through a hot water storage tank. For control design, a lumped parameter model is first developed to describe the dynamics of the system in an explicit form of input-output relationship. The system has been fully-instrumented to examine its performance under different operation conditions. The system model is then validated by extensive experimental tests. The predictions from the models exhibit a good coincidence with experimental results, judging by an RMS error less than 15%. Based on the obtained dynamic model, a linear quadratic regulator (LQR) is applied to optimize a cost function of the output errors and control efforts. The key challenge is to regulate the refrigerant temperature entering the condenser by controlling the valve opening. The design approach is then tested in a transient simulation tool to predict the system performance in transient conditions. The experimental results obtained from implementation with PLC demonstrate that the proposed system delivers higher system efficiency owing to the higher refrigeration effect in the direct expansion evaporator. Thus, the novel development is promising for improvement of energy efficiency, enhancement of the system performance while fulfilling the cooling demand. Consequently, between 25 and 43% of monthly electricity can be saved on average.

Aug 1, 2013

By Frank Milliken

IN September 1937, the Ohio Copper Co. inaugurated the treatment of its copper-bearing mill tailings at Lark, Utah. These tailings had been accumulated during the regular operation of the Ohio Copper mine and mill over the period 1007 to 1019. Gravity concentration had been employed except for a comparatively short period in 1919, when flotation was used. The ore milled during that period assayed about I per cent Cu. The chief copper mineral, chalcocite, was dissemi-nated in a shattered quartzite, mainly along fracture or cleavage planes. The quartzite gangue was extremely hard and grinding to liberation resulted in excessive sliming of the "sooty" chalcocite, with consequent high tailings losses. Recovery on the seven million tons treated was prob-ably less than 6o per cent of the total copper content. As early as 1918, attempts had been made to sample the dump. In 1928, a com-plete sampling program was undertaken. The sampling consisted of seventy-four 5-in. post auger holes drilled to the full depth of the dump at regular intervals of 250 ft. Each 10-ft. portion thereof com-prised a sample for analysis. Each sample was screened, rolled, divided into three parts, dried and assayed. The reject was retained for testing purposes. From the depth of the auger holes a contour map of the dump was plotted, Fig. 1, which gives percentages of tonnage and copper content.

Jan 1, 1940

By Hugo L. Johnson, Robert Wallace

THE Midvale plant of the United States Smelting Refining and Mining Company consists of a flotation mill for concentrating sulphide ores of lead and zinc by differential flotation to produce three separate concentrates, one of lead, one of zinc, and one of iron pyrite; and a lead smelter for smelting ores and concentrates to produce base lead bullion, The plant, including its shops, laboratories, office, railroad yards which serve both mill and smelter, and areas reserved for tailing ponds and slag dumps, covers 646 acres on the right bank of the Jordan River at Midvale, Utah. It is twelve miles south of Salt Lake City and sixteen miles east of the West Mountain mining district at Bingham Canyon from which is drawn a large part of its ore supply. Custom ores are treated as well as the product of Company mines.

Jan 1, 1948

By R. J. Craig

Introduction All mining operations produce rock dust. Inhalation of rock dust, particularly if it has a high silica content, causes silicosis. Silicosis is, therefore, recognized as a hazard of the mining industry and has been made compensable throughout most of Canada. Most of the dust in any mining operation is caused by rock drilling and blasting operations and the movement and transportation of broken rock. Dust from blasting cannot be eliminated, but it can be controlled by means of increased ventilation, the use of water sprays, and the control of blasting hours. Dust from ore movement can be reduced by keeping the broken rock in a moist condition at all times. The dust from the rock drilling operation has been found to be the most difficult to control. Concentrations of dust caused by rock drills in stopes can usually be reduced to the safe minimum of 300 particles per cubic centimeter (p.p.c.c.) by diluting the air with increased ventilation. In development headings, where the machines are more confined, this is not always practicable. Therefore, the dust must be eliminated at its source. This paper deals with the reduction of dust from Leyner machines by adopting improved designs.

Jan 1, 1947

By C. E. Wicks, J. E. Tress, F. E. Block

The Bureau of Mines investigated the effects of gamma radiation on materials and chemical reactions to obtain information that could be of value in modern metallurgical practices . Various combinations of metals and their ores and compounds were irradiated in attempts to effect reactions that might be applicable in the extraction and separation of metal values from minerals and The types of reactions studied included complexing of salts , decomposition of hydrated salts , metal chlorination reactions , leaching of ores and minerals , halogen exchange , and various reducing reactions . All irradiations were performed at the Materials Testing Reactor Gamma Facility of the U.S. Atomic Energy Commission at Idaho Falls , Idaho . Spent fuel elements were utilized as the source of the gamma radiation . Some irradiation - induced changes , ranging from mere color change to participation in chemical reactions , were noted . The greatest value of these investigations , however , was the experience acquired , which should be valuable in future explorations of similar nature .

Jan 1, 1964

By Mostafa Benzaazoua, Mariam El Adnani, My Ahmed Boumehdi, Rachid Hakkou, Salah Ouhamdouch, Abdelmalek Goumih

This study focuses on the environmental characterization and assessment of long-term neutral mine drainage (CND) potential from waste rock piles at the abandoned Erdouz mine in Morocco. The study involved metallographic analysis, static tests, and column tests. Results indicate that the waste rock is not an acid mine drainage generator but produces CND, mainly with sulfates exceeding Moroccan standards. The waste rock is relatively stable and could be reused after pretreatment.

Jan 25, 2022

By Johannes Münzer

Regeneradores são elementos importantes em uma usina siderúrgica. Eles são os responsáveis pelo aquecimento do ar de sopro aplicado no alto-forno a partir do aproveitamento da energia contida nos gases do processo de produção de ferro gusa. Dessa forma, os regeneradores estão diretamente associados ao processo siderúrgico. Durante do seu ciclo de trabalho, o qual se denomina campanha, problemas podem ocorrer devido a variações operacionais indesejadas, falhas de projeto, entre outros fatores. Num ambiente onde o tempo cessante de um equipamento gera enormes custos, a solução é desenvolver soluções customizadas que minimizem essa interrupção. Cada uma das partes do regenerador tem funções únicas e consequentemente soluções únicas, que visam o reparo no estado da arte com menor custo.

Aug 17, 2017

By Guilherme Vieira Braga Lemos

Uma superliga a base de Níquel, popularmente conhecida como Inconel 625®, foi estudada no presente trabalho. A Soldagem por Fricção e Mistura Mecânica (SFMM) aplicada a liga 625 foi realizada com velocidades de rotação da ferramenta entre 1200 a 200 rpm e velocidade de soldagem entre 1 e 1,5mm/s. O aporte térmico foi calculado como função dos parâmetros de soldagem empregados. Adicionalmente, análises metalográficas e de microdureza foram realizadas na seção transversal das juntas soldadas. A aplicação da soldagem no estado sólido foi efetiva e resultou em maiores valores de microdureza todas as juntas soldadas. Por outro lado, um aumento na velocidade de rotação causou um aumento do aporte térmico.

Aug 17, 2017

Exploration for uranium in Australia commenced only during the 1940s, but in this short period has been very successful as one third of the world's low cost uranium reserves have been discovered in Australia. Total uranium exploration expenditure in Australia up to the end of 1983 was $A(1983) 554 million; this discovered 20 potentially economic deposits and official reserves of 560 000 tonnes of uranium oxide at an average cost of $1 per kg of U 0 . An exponential 8 eserves indicates distribution of uranium r that there could be 54 undiscovered uranium deposits in Australia, each with reserves of 20 000 tonnes U308 or more, in addition to smaller deposits. Using a constant uranium price of $A(1983) 79 per kg, no deposit is economic at a grade below 0.12 per cent U 08 or with reserves of less than 3 000 tonnes. Selecting deposits with reserves of 5 000 tonnes U 0g or more as prime exploration targets, only 39 per cent of discoveries will yield a real internal rate of return (IRR) of 10 per cent or more. After committing a minimum exploration budget of $10 million to this search, an explorer has one chance between 7 and 12 of discovering a deposit that will repay the exploration investment.

Jan 1, 1984

By Maísa Villela Freire

Refratários MgO-C encontram-se entre os mais adequados para o uso na linha de escória de panelas para aço líquido. Seu comportamento, nesta aplicação, depende de fatores termodinâmicos e cinéticos. Métodos de cálculo termodinâmico para avaliar o potencial de degradação de refratários MgO-C por escórias e pela atmosfera são revistos brevemente. Tais métodos envolvem, em geral, premissas importantes sobre a quantidade de materiais envolvidos. Para avaliar um método mais simples, foram escolhidos dois tijolos MgO-C e duas escórias típicas do processo da CSN. Estes tijolos e escórias foram caraterizados, neste trabalho. O método apresentado consiste na realização de cálculos de equilíbrio em que a principal variável é a fração de escória em uma mistura hipotética com o refratário. Para a composição do refratário foram empregadas (a) composição média e (b) composição da matriz do tijolo. Os resultados indicam que é possível realizar previsões iniciais quanto à reatividade do refratário e determinada escória de forma simples. Os cálculos, evidentemente, não substituem testes cinéticos e testes em escala industrial, em vista da complexidade dos sistemas em questão.

Aug 17, 2017

By R. Venugopal, V. K. Saxena, S. K. Tripathy

"This study was carried out to understand the impact of variation in material morphology on the efficacy of microwave pretreatment. Three different types of mineral matter – coal, iron ore and manganese ore – were treated with microwaves at different energy levels, from 180 to 900 W, for different time durations of one to five minutes. The treated samples were subjected to microscopic, milling and liberation studies. Coal is a porous and amorphous material with low dielectric constant, and grinding of the microwave-pretreated coal samples resulted in an 18.18 percent reduction in the 80 percent of passing particle size, or d80, and a 17.1 percent increase in carbon recovery. The microwave-pretreated soft and friable manganese ore samples showed a 47.82 percent reduction in d80 during grinding and higher manganese recovery of 42.46 percent during liberation analysis. The microwave pretreatment and milling of hard and banded iron ore reduced the d80 by 20.83 percent, but no improvement was observed in mineral liberation. Coal showed better results during treatment at lower energy levels of 180 W for one to three minutes, whereas the minerals needed higher energy of 900 W for five minutes. Particle size analysis indicated rapid size reduction up to an energy input of 25 Wh. This effect diminished with increased energy input.IntroductionComminution is an important unit operation in mineral processing plants for the purposes of size reduction and mineral liberation. But most comminution technologies are energy inefficient and only a small amount of energy is consumed in real size reduction, with the rest wasted. High-grade mineral resources have been exploited on a large scale for the last century, and the upgrading of low-grade resources is now required to fulfill the needs of industry. Pretreatment methodologies for comminution will play a crucial role in the upgrading of low-grade mineral resources. Researchers have studied various pretreatment methods to develop an energy-efficient and techno-economically viable solution to improve mineral liberation and product fineness with minimum energy consumption. Most of these studies were focused on the use of chemical additives, thermal, ultrasonic and microwave treatment, and electric disintegration (Klimpel and Austin, 1982; Norgate and Weller, 1994; Gaete-Garreton, Vargas-Hermandez and Velasquez-Lambert, 2000; Wilson et al., 2006; Kumar et al., 2010; Wang, Shi and Manlapig, 2011; Singh et al., 2012)."

Jan 1, 2017

By Paulo Sérgio Moreira

O tamanho de grão austenítico prévio é determinante na área de tratamentos térmicos dos aços, pois este parâmetro influencia sua microestrutura e propriedades. Para que o tamanho de grão possa ser medido, é necessário que antes se aplique métodos de contraste para sua revelação. A literatura relata, entre métodos desenvolvidos, dificuldades em se conseguir bons resultados em função deles serem susceptíveis a variações de composição química e histórico de processamento dos aços. Neste contexto, esse trabalho propôs métodos para a revelação dos contornos de grãos austeníticos prévios dos aços ABNT4340 e ABNT1030. Foram utilizadas duas técnicas: ataque químico e ataque térmico. Para a técnica de ataque químico, utilizou-se um reativo a base de ácido pícrico. Já na técnica de ataque térmico, as amostras foram austenitizadas de forma a promover uma oxidação controlada. Os resultados obtidos mostram o sucesso das técnicas, com destaque para o ataque térmico que se mostrou mais efetivo para o objetivo proposto. Foi possível mostrar que no ataque químico, o ajuste da concentração de HCl em função da composição química do aço é o ponto de maior importância, ao passo que no ataque térmico, a segregação química e a temperabilidade dos aços são relevantes para o sucesso da técnica.

Aug 17, 2017

By Dwayne D. Tannant

The Adra tunnel near Naramata BC experienced a fire in 2010 that burned timber sets within the tunnel and caused severe spalling of rock from the roof and tunnel walls. The nature of the damage is documented and efforts completed to rehabilitate and open a portion of this tunnel to the public are described. The use of shortcrete and rock bolts is a technically and economically superior support system to timber sets as well as being far more fire resistant.

Jun 1, 2012

By Rina Kim

The addition of lead to a gold leaching reactor can effectively accelerate or retard the gold cyanidation reaction. This study explored the effect of lead on the gold dissolution kinetics using cyclic voltammetry (CV) experiments. It was illustrated that the gold leaching kinetics in the cyanide solution enhanced with the addition of lead salt in the low overpotential region (–0.35 V vs. Ag/AgCl). The similar behavior was observed in the presence of ore containing 0.25% galena. In contrast, the gold oxidation kinetics retarded at –0.35 V (vs. Ag/AgCl) in the presence of silicate and lead-bearing mineral under certain conditions. Likewise, the lead addition was not functional for the high sulfur ore. This was attributed to the oxidation of the sulfides to the elemental sulfur, which subsequently formed a passivating layer on the gold surface. The results were evidently affirmed by the electrochemical tests and X-ray photoelectron spectroscopy (XPS) analysis.

By Carlos Alberto Alves Nunes Filho

Este trabalho tem o objetivo de traçar o panorama atual das exportações de minério de ferro e a logística integrada desde a jazida, extração, empilhamento e transporte para uma área de armazenagem próxima ao Terminal Portuário do Pecém para posterior embarque no navio e entrega ao cliente final. Optou-se por uma pesquisa exploratória descritiva para identificar as dificuldades na logística que dificultam o escoamento do minério pelo Terminal. Utilizando dados coletados de empresas que atuam na região e que utilizam o Porto do Pecém como saída de sua produção, demonstrando também os estudos de custos e de produção, tipos de modais mais utilizados os navios e suas especificações que fazem o transporte do minério a granel, os equipamentos pertinentes a operação portuária de embarque, bem como os tipos de minério existentes e os que são encontrados nas áreas de mineração no Estado do Ceará e as suas características. O Terminal Portuário do Pecém possui uma estrutura de acostagem preparada para esse tipo de operação proporcionando facilidades aos exportadores.

Aug 17, 2017

By Peter Voulgaris, Allan Haines, Diane Walker, Ian de Bruyn

The Oyu Tolgoi porphyry gold and copper project is located in the south Gobi region of Mongolia. The Ivanhoe Mines project has the potential to become a long-life copper and gold producer that could rank among the largest in the world. There are five deposits which cover a strike length in excess of 6.5 km, from south to north they are named South Oyu, Southwest Oyu, Central Oyu, Hugo South and Hugo North. The first three, collectively known as the Southern Oyu deposits, are planned to be mined by open pits, whilst extraction of the deeper Hugo deposits is planned using block caving techniques. The pits will have diameters of approximately 1000m and a maximum depth of 550m. The geological environment consists of a sequence of porphyritic augite basalt, dacitic tuffs and sedimentary rocks that have been intruded by several generations of porphyritic quartz monzodiorite and numerous post mineralization dykes. Several major faults cut through the southern deposits juxtaposing the relative position of the stratigraphy. The geotechnical investigation for the Oyu Tolgoi Open Pits was conducted in three distinct phases of increasing complexity: scoping study; advanced scoping study and feasibility study. Each phase consisted of data collection, interpretation and analysis designed to progressively develop 3D geotechnical domaining for the empirical, structural and numerical evaluations. The development of the geotechnical design parameters for these green fields open pits posed many technical challenges, brought about by the conditions associated with a lithologically and structurally complex environment. The design work focused on the optimization of the pit geometry to conform to equipment selection and blasting characteristics. Limiting bench stack heights were derived from the influence of major structures. The overall slope angles in each pit sector were developed around the requirement for haulage ramps and geotechnical berms. This paper describes each of these aspects and the methodology used to address the integration of the geotechnical characteristics with the mining environment.

Jan 1, 2006

By A D. Campbell, G R. Power

The increasing availability of marker data in sublevel caving operations is changing the way draw can be managed to achieve positive recovery outcomes in these mines. This paper describes how marker data has been incorporated into flow simulations to help calibrate full mine ore recovery simulations for the forecasting and optimisation of recovery.Some flow modelling techniques do not use marker data, relying instead on the outcomes of physical and numerical experiments to guide assumptions about an idealised recovery flow shape. Other mines have access to marker trial data, but find it difficult to specifically link this marker trial information to their recovery models. This can make it difficult to create a link between the marker trial information and recovery forecasting and limits the potential value of the marker trials at the mine.In the simulations shown here, the marker rings are fully incorporated into the flow model, and can be tracked in the model. The model is compared against the real underground marker recovery information to give the user an indication of how accurately the flow settings in the model are reflecting the conditions in the experimental marker rings. An example of use of this system at an operational mine is included.CITATION:Power, G R and Campbell, A D, 2016. Modelling of real-time marker data to improve operational recovery in sublevel caving mines, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 105–110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

The Golden Cross mine is situated in a sensitive environmental setting on the North Island of New Zealand, about 150 kilometres south-east of Auckland and about 8 kilometres NW of Waihi. The mine is situated in dipping topography, with volcanic ashes making up soils, fault zones running through the area, and rainfall of about 3 m per year on average. Water management is the most demanding environmental challenge on site, and a comprehensive programme has been put in place to address tailings deposition, long term tailings storage, and water treatment during and after operations.   The tailings impoundment is built with an underdrainage system that collects groundwaters and waters that seep through the impoundment. The embankment and impoundment are both built to withstand the Maximum Credible Earthquake and the Probable Maximum Flood. Tailings are treated to remove cyanide and to decrease metal solubility to reduce long term risk to water quality after mining. A state-of-the-art water treatment plant is utilised to treat water from the underdrainage system and water decanted from the top of the tailings pond and stormwaters to remove residual cyanide and metals to extremely high standards with a great deal of reliability and at reasonable cost. Closure of the facility addresses long term post mining water quality issues, and rehabilitation of the area with wildlife habitat as a priority.

Jan 1, 1995

By Lindaura de Souza Cândido d'Avila

O presente trabalho é parte de um estudo mais abrangente que busca o desenvolvimento da mistura de diferentes tipos de minérios de ferro para a maximização da produtividade na sinterização. Essa etapa do estudo teve o intuito de avaliar as diferentes características do minério de ferro itabirítico e sua influência na produtividade da sinterização em escala piloto. Inicialmente foi realizada a caracterização dos minérios de ferro hematítico e itabirítico oriundos do Quadrilátero Ferrífero. Em seguida, foram testadas em escala piloto misturas de minério de ferro com proporções variadas de minério hematítico e itabirítico. A partir dos resultados de produtividade e de qualidade do sínter obtido foi possível avaliar o efeito do minério itabirítico na mistura de sinterização. Tais resultados indicam diferentes desempenhos desses parâmetros na unidade piloto de sinterização.

Aug 16, 2017

By Ligia Mara Gonzaga

A separação magnética ocupa uma posição importante na concentração de minérios de ferro e há grande interesse em avaliar a sua aplicabilidade na etapa de projeto.Isso pode ser realizado por meio de uma caracterização adequada do minério e do uso de ensaios em bancada. O presente trabalho aplicou uma metodologia baseada na caracterização para avaliação do potencial de aplicação da separação magnética de baixa intensidade no WDRE, bem como o separador magnético de alto gradiente (HGMS) Rapid para dois minérios de ferro itabiríticos. Estudos detalhados de caracterização granulométrica, química e mineralógica das amostras, britadas abaixo de 1,18 mm, foram realizados. As análises demonstraram as diferentes composições mineralógicas dos minérios, sobretudo no tocante aos teores de magnetita e hematita. A fim de caracterizar a distribuição dos componentes magnéticos das diferentes amostras preparadas foi realizado o seu fracionamento utilizando o separador magnético Isodinâmico Frantz, que permitiu estabelecer os intervalos de intensidade de corrente preferencial de ocorrência das principais fases presentes nas amostras, sendoos resultados aplicados com sucesso na previsão da separação magnética.

Aug 16, 2017