Search Documents

By Craig R. Barrett

The influence of the stress dependence of the dislocation density on the overall stress dependence of The steady-state creep rate is discussed. Experimental measurements of dislocation densities and creep rates jor an Fe-3.1 pct Si alloy tested over a wide range of stress are presented which indicate a close correlation between the two quantities. EXPRESSING the stress dependence of high-temperature steady-state creep rates has been the subject of numerous investigations over the past decade. From these investigations have emerged a few general equations which fit most of the available data reasonably well. Garofalo 1 has proposed that for a wide range of stress and temperature the creep rate, i, can be expressed by a relationship of the form: where A, ß, and n are temperature-dependent and is the applied stress. Eq. [I] gives a stress dependence of a at low stresses and exp(nßo) at high stresses, both consistent with experimental observation where n = 5. A number of other investigatorshave proposed a similar expression where: where m and w are in general functions of temperature. Theoretical justification for Eqs. 111 and [2J comes from two different approaches, theories based on dislocation glide3-5 and theories based on the balance between work-hardening and recovery.' Dislocation glide theories predict where p is the mobile dislocation density and V is the activation volume. In order for Eq. [3] to predict a on stress dependence at low stresses with n = 5, it is necessary for p to be a strong function of stress, about proportional to u3 or u4.436 Recovery models of creep start with the general expression:' where r is the recovery rate and h is the work-hardening rate, and then employ a detailed model to determine the stress dependencies of r and h. As example, weertman2 has described a model based on pile-up hardening which results in an expression similar to Eq. [2] with m = 2 and p = 2.5. A recent, seemingly more general approach suggested by McLean is to use Friedels dislocation network growth expression to calculate the stress dependence of r. This model predicts r = p 3,2 and, as h is taken to be a relatively weak function of stress, the stress dependence of i should be about proportional to p3, 2. Once again, it is required that p be a strong function of stress to yield i This recovery model is by no means complete as the stress dependence of network growth is calculated in the absence of an applied stress meaning that r should probably be a stronger function of stress than given by p3, 2 and also some recent work by Mitra and McLean8 suggests that the stress dependence of h may be as large as Because of the importance of the stress dependence of p in determining the overall stress dependence of the strain rate it seems reasonable to examine this relationship in some detail. Measurements made on dislocation densities present during high-temperature steady-state creep generally obey the following relationship a =o0 + aGVWp [5] where uo is usually called a friction stress, a is a numerical constant about equal to unity, G is the shear modulus, and b is the Burgers vector. Depending on the magnitude of uo, data obeying Eq. [5] can give rise to a range of stress dependencies of p. For example, if we assume that the expression where 6 is some constant, adequately represents the stress dependence of p over a range of o, then from Although Eq. [6] obviously breaks down when u 5uo for uo 6 can vary over a wide range of values. In particular, if u > a, > 0 then 6 will be greater than 2. As an example the data of Ishida and McLean are plotted in Fig. 1 showing excellent agreement with dynes per sq cm) and also showing good agreement with a p cc u3 dependence when plotted on a log-log basis. As oo increases 6 tends to increase and correspondingly the stress dependence of the predicted creep rate should also increase,* as-

Jan 1, 1968

By Peng Qian, Xiao Li, Guoyan Fu, Peiwei Han, Yongliang Wang, Shufeng Ye

"Arsenic removal from high arsenic gold concentrate is conducive to increase the mineral value and realize the mineral comprehensive utilization. This study investigated the alkaline pressure oxidation leaching (APOL) of an arsenical gold concentrate in lower temperature to separate the arsenic into filtrate. The effects of temperature, NaOH concentration, solid-liquid ratio, reaction pressure and stirring speed on the leaching efficiency were investigated, and the characteristics of the gold concentrate and leaching residues were evaluated using XRD and SEM analysis methods. The obtained results showed that by using lower temperature (<60?) it is possible to avoid the production of elemental sulfur during the leaching process, which is benefit for the oxidation of arsenopyrite; When the reaction was carried out under appropriate conditions, more than 98% of the arsenic will be extracted into the filtrate as the form of arsenate or thioarsenate. INTRODUCTION In recent years, there has been considerable interest in the recovery of gold from refractory arsenical gold ore. The arsenic in this kind of ore usually exists as the form of arsenopyrite, and the gold surrounded by arsenopyrite exists as the form of fine particles, which will give many difficulties to metallurgical work. When the content of arsenic in the gold ore is more than 0.5%, it will seriously penalize the smelting efficiency (Ruiz et al., 2014). So pretreatment of the refractory gold ore is necessary to obtain the largest economic value and environmental benefits (Balaz et al., 2000). The oxidation pretreatment processes mainly include roasting oxidation, pressure oxidation, chemical treatment and biological treatment (Ann et al., 1992; Kou and Chen, 2012; Tongamp et al., 2010; Fernandez et al., 1995; Lin and Zheng, 1996). Among them, the roasting oxidation and pressure oxidation are the more ordinary processes in industry. The roasting oxidation process is the mature and adaptable technology, but the production of waste gas containing sulfur and arsenic will pollute the environment. The pressure oxidation method possesses certain metallurgical and environmental advantages, and can efficiently decompose the mineral. According to the different solution media, the pretreatment can be divided into alkaline and acidic pressure leaching pretreatments (Papangelakis and Demopoulos, 1990; Hiskey and Sanchez, 1995). The acidic pressure oxidation method has been used in most smelting plants for high arsenic gold ore pretreatment, while the alkaline pressure oxidation is still not widely applied. Compared with the acidic pressure oxidation, the alkaline pressure oxidation can be realized under lower temperatures."

Jan 1, 2018

By Circadian Technologies

Alertness levels naturally fluctuate during the day and night Basic functions ??digestion, body temperature ? follow predictable 24-hour patterns Adjustment to night work creates health challenges for shiftworkers Performance decreases during overnight and post-lunch dip hours Fatigue supercedes training & experience Fatigue is a major cause of human error

Jan 1, 2010

By I. W. L. Finlay, H. R. Ogden, R. Jaffee, D. J. Maykuth

Aluminum has been found to be soluble in a titanium to about 26 pct, and to raise the temperature range of transformation from a to 8. Two intermediate phoses exist in the system, a new face-centered tetragonal phase, designated as 7, which occurs between 34 and 46 pct Al, and TiAI Metallographic and X-ray diffraction data were used to determine the diagram. ALUMINUM is one of the useful alloying additions for titanium-base alloys. It is an important constituent in two commercial alloys released in 1950, one containing 4 pct A1 and 4 pct Mn, and the other containing 3 pct A1 and 5 pct Cr as the metallic alloy content. It is probable that, in the future, other titanium alloys containing aluminum will be released. In the course of alloy development work, some of the features of the constitution of titanium-rich Ti-A1 alloys have been developed. These are described in the present paper. The only available information on the Ti-A1 system concerns the aluminum-rich end of the diagram. In summarizing the early work, Hansen&apos; indicated that there is little solubility of titanium in aluminum, and that a two-phase region exists up to the intermediate compound, TiA1a (37.2 wt pct Ti), which has a congruent melting point at 1355°C. Fink&apos; has reported that a peritectic reaction occurs at 665°C between the melt and TiA1³ to form the terminal solid solution of titanium in aluminum. The solubility of titanium in aluminum has been established at 0.24 pct at 510°C and is estimated to be between 1 and 1.5 pct at the peritectic temperature. No information has been published on the diagram above TiAl,, other than a statement- hat aluminum raises the a to ß transformation temperature of titanium. Materials and Preparation of Alloys Iodide-type titanium and high-purity aluminum were used in this investigation. Typical analyses of these materials are given in Table 1. Alloys were prepared by arc melting on a water-cooled copper hearth, using the techniques described previously for contamination-free melting.&apos; Weight losses during melting were very low, ranging from 0 to 0.02 g in a 10 to 15 g charge, indicating that little or no loss of aluminum occurred during melting. This permitted the use of nominal compositions for these alloys. Alloy ingots containing from 0 to 7.5 pct A1 were rolled in air at 850°C to 0.040 in. sheet. Alloys containing from 7.5 to 16 pct A1 could only be rolled about 25 pct reduction at temperatures up to and including 1200°C. Alloys containing above 16 pct A1

Jan 1, 1952

By R. Y. Wan

Acid ferric sulfate solution has been used for heap and dump leaching of low-grade chalcopyrite ores and is being considered as a possible lixiviant for the hydrometallurgical processing of copper sulfide concentrates. For many years, researchers have attempted to explain the leaching behavior of chalcopyrite, since the reaction rate kinetics are extremely slow and seem to be significantly influenced by the nature of the reaction product. A summary of conclusions drawn from reported literature on chalcopyrite leaching is found in the paper by Munoz, Miller, and Wadsworth(1) and more recently by Dutrizac.(2) Lowe(3) and Jones and Peters (4) attributed rate control to a surface reaction. Linge,(5) Dutrizac,(6) Bauer,(7) and researchers at the University of Utah(1,8) reported that the reaction rate is limited by transport in the chalcopyrite lattice or through the elemental sulfur reaction product layer. Munoz et al.(1) presented a model, derived from the Wagner theory of oxidation, which is based on the formation of a protective sulfur layer with rate control by electron transport through the insulating sulfur layer. By utilizing Wagner&apos;s parabolic oxidation relationships, (9) the following equation was obtained: [ ] where a is the fraction of CuFeS2 reacted at time t, pB is the molar density of CuFeS2, do is the initial diameter of the particle, e is the electronic charge, s is the total electrical conductivity of the sulfur layer, and ?G is the Gibbs free energy for the reaction:

Jan 1, 1984

By William C. Cassun

The important role of pit slope design in the overall economics of open-pit mining ventures has long been recognized and well documented.1 2 Any economic analysis of a pit slope design must reflect the trade-off between the benefits and the increased risk of slope failure inherent in steeper slope angles. The conventional practice in pit slope design is based on the factor of safety analysis.&apos; The approach uses average values to arrive at a deterministic solution to slope stability. Past analyses based on this approach generally have had several drawbacks: 1. The risk from slope failure could not be quantified. 2. Only relatively simple pit wall geometries were considered. 3. The analyses were performed solely for the benefits of steeper slopes, seldom discussing the potential costs of slope failures. 4. Analyses were seldom considered in a year-by-year mine planning context. Recognizing that average values do not reflect the uncertainty in geomechanical parameters, a probabilistic philosophy to slope design has evolved. 4,5 However, this approach had not been fully developed to include complex slope geometries and mine planning consideration. In order to develop an integrated, pit slope design procedure, a research project was initiated at the University of Arizona during 1973 in conjunction with the Canada Center for Mineral and Energy Teleology. This research resulted in the development of a probabilistic design procedure. The remainder of this paper gives an overview of the probabilistic design procedure and a discussion of the requirements for the benefit-cost analysis of a pit slope design. Finally, the results of a case study undertaken at an operating mine are given.

Jan 1, 1977

By Joseph L. Walker

INTRODUCTION In looking over the diversity of the papers that are being presented during this meeting on The Industrial Practice of Fine Coal Processing one cannot help but be impressed with the progress the industry has made in beneficiating fine raw coals, and in the number of innovations that are under study to increase recovery and to improve the quality of the finest size particles produced at a preparation plant. Those who are not in our industry, who look at the technical program, might be confused, when they see that the papers include such topics as cleaning to zero and heavy media cyclone cleaning 28M x 100M; application and performance of fine coal jigs, tables, hydrocyclones, spirals, and flotation; filtration, dewatering and thermal drying; and ancilliary aspects such as fines handling, instrumentation and process control plus screening and liberation. This is an observation and not a criticism of the diversity of papers being presented. The program fits within the parameters of fine coal preparation as the term "coal preparation" is defined, but perhaps not as the term "fine coal" is defined. Admittedly these definitions are sometimes loose. However, each should be made more definitive if a meaningful fine coal preparation overview is to be possible. COAL PREPARATION DEFINED In the opinion of the writer, the term "coal preparation" should be defined as including all work activities that are performed on all components of a run-of-mine coal from the time it leaves a surface reserve or an underground portal, until all components are either ready for shipment or are stowed on, or in the earth in an environmentally acceptable manner. This definition excludes the work that is performed to improve coal quality or handleability inside the mine or pit. This work is commonly called "face" or "pit" preparation. FINE COAL DEFINED The term "fine coal" means different things to different people. In the past, anthracite finer than No. 3 Buckwheat (3/16 in.) was considered fines which often were discarded from the breaker as an unsalable by product; and bituminous coals finer that about 1/4 in. (slack) were either discarded or sold at cost to prevent an accumulation of "no bills" which referred to a product having no immediate sale. Although a standard definition of "fine coal" is yet to be accepted by the industry, a designation of coals by particle-size range has evolved through the wide use of three-circuit flowsheets, wherein the optimum size range by washer type determines the size fractions: a coarse-coal circuit for the plus 3/8 in., a -11- coal circuit for the 3/8 in. x 28 Mesh, and a fine-coal circuit for the remaining 28 Mesh x 0. Logically, the term "fine coal" should refer to some resultant size fraction or some top size by zero. This definition should include a 28 Mesh x 0 feed to a flotation cell but should exclude a 28 x 100 Mesh size fraction fed to a heavy media cyclone. Failure to include the resultant sizes in the definition precludes accounting of the full range of particle sizes present in the feed to the plant. Since the 28 Mesh x 0 fraction is treated in the final circuit of the three discreet washing circuits, now almost always used in U.S. commercial applications, and since it contains all of its resultant sizes, in the writer&apos;s opinion, it should be designated "fine coal". FINE COAL CLEANING Cleaning coal fines, which in the past was at best marginally profitable, is now an essential part of coal preparation strategy for a number of reasons : 1. Raw coals now cost more to produce and

Jan 1, 1988

By X. Xu

This paper presents the research on comprehensive recovery of copper, gold, silver and iron from tailings from high-intensity magnetic separation in Tonglushan Mine. By comparison of experimental results of three flowsheets?regrinding of tailings-conventional sulphidizing flotation, water heating enhanced sulphidizing flotation and acid leaching-sulphidizing precipitation flotation, it is concluded that regrinding of tailings-conventional sulphidizing flotation flowsheet has the best economical and technical performance and practicability. Regrinding and using the mixture of sodium hydroxamate and sodium xanthate are two of the notable technical characteristics of this best flowsheet. The system for comprehensive recovery of tailings has been put into production. It not only can recover the valuable minerals from tailings in Tonglushan Mine, but also can reduce the environmental pollution, resulting great economic and social benefit.

Jan 1, 2014

By G Harbort, K Quan

Traditional engineering practice for concentrator design uses a mixture of risk minimisation options and capital minimisation approaches. Often this is based on the preferences and experiences of the engineers involved.A geometallurgical approach involves identifying primary lithology, alteration, and mineral dispersion patterns within a deposit to allow representative samples for test programs. This provides a method to infer from laboratory test results meaningful production data for larger amounts of the ore body. Geometallurgical models can be integrated into the resource block model and subsequent mine plan and can assist in predicting when difficulties in the processing route might be expected, allow adjustment of the design to compensate for these or provide an early warning system so that production forecasts can be more adequately developed. Simulation modelling is the process of creating a computer model of a real system based on mathematical logic. In simulated time, the model explores the randomness and chronological sequencing of events observed on real systems. The objective is to mimic the real system with sufficient accuracy to make predictions of real behaviour under experimental conditions. Amec Foster Wheeler often use the ‘discrete-event’ simulation modelling technique. This method is well suited for inclusion of the statistical variation of effects in unit operation, mechanical availability, throughput and operating strategy (based on historical operating data for equipment downtime), operating schedules and equipment capacity. The net result of the simulation model is an analysis that can quantify risks in terms of system performance and capital and operating costs.CITATION:Harbort, G and Quan, K, 2017. Concentrator design – standard engineering practice versus geometallurgy and simulation, in Proceedings MetPlant 2017, pp 195–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

From time to time the Bureau of Mines has interpreted and applied certain provisions of the Federal Coal Mine Safety Act and Federal Mine Safety Codes, primarily for the guidance of Federal Coal Mine Inspectors. Although interpretations of the Act have appeared in the Federal Register, the Code interpretations and practical applications have not been published. In response to many requests from representatives of the coal-mining industry, the Bureau is publishing this information to promote better understanding of those provisions that may be misinterpreted or misapplied. INTERPRETATIONS AND APPLICATIONS Two Federal Mine Safety Codes are discussed in this report, namely the Federal Mine Safety Code for Bituminous-Coal and Lignite Mines of the United States, Part 1, and the Federal Mine Safety Code, Anthracite Mines of the United States, Part 1. In this circular the word Codes refers to both directives; Code* refers to the code for bituminous-coal and lignite mines; Code? refers to the one for anthracite mines. Act* refers only to bituminous-coal and lignite mines.

Jan 1, 1963

By Tristan Worsey, Jhon Silva

The paper discusses a limestone quarry case study that looks at change in fragmentation due to using different charge sequences when using the regular rhythmic timing method.

Feb 1, 2020

By Clarence Hall, Charles E. Monroe

Squibs, Fuse, and Detonators It has been made clear in the discussion of combustion and explosion and the description of various explosives that they can be caused to explode by various means. All of them can, under some circumstances, be made to explode by fire. Some of them can be caused to undergo a detonating explosion by setting off a detonator in contact with them. In blasting use is made of both these means for setting off explosives, the means used being determined by circumstances.

Jan 1, 2010

By Yongheng Jiang, Wentong Wang, Haoming Luo, Chuanju Liu, Qianjun Zhang, Sha Guo

Rock burst has always been a major problem in deep underground engineering with high stress, and rock burst strength evaluation has become an important research topic. To effectively predict the rock burst hazard in underground rock mass engineering, a cloud model (CM) rock burst intensity evaluation method based on the CRITIC method and order relation analysis method (G1) was proposed in this paper. First, a rock’s uniaxial compressive strength σc, tangential stress σθ, uniaxial tensile strength σt, ratio of uniaxial compressive strength to tensile strength σc/σt (brittleness coefficient), ratio of tangential stress to uniaxial compressive strength σθ/σc (stress coefficient), elastic deformation energy index Wet, and depth of cover H were selected as evaluation indices of rock burst intensity. Ninety-five groups of rock burst measured data at home and abroad were selected, and the objective weight and subjective weight of each index were calculated by using the CRITIC method and G1 method, respectively. The comprehensive weight was determined according to the combined weighting method of game theory, and the sensitivity of each evaluation index was analyzed. By utilizing a forward cloud generator, the membership degrees of different rock burst grades were calculated, and then the rock burst intensity grades of the samples were evaluated and compared with the evaluation results of the CRITIC-CM method and G1-CM method and the actual grades. Finally, the rock burst classification ability of the model was analyzed. To better verify the accuracy and reliability of this model, the rock burst case of the W39 line in the Chengchao Iron Mine was analyzed by using this model. The research results show that the rock burst evaluation results based on CRITIC-G1-CM are basically consistent with the actual rock burst grade, and the rock burst intensity grade evaluation model has good practicability and reliability.

Sep 1, 2023

By Peter Jackson

The dewatering of the large construction pits required for major infrastructure projects often has a significant impact on the environment. This is particularly so in urban areas and where groundwater resources are of interest. These environmental impacts are inter alia, groundwater lowering and the consequent effects such as settlement and deterioration of timber foundations, together with the impact of the dewatering on the groundwater quality. In order to minimise the environmental impact of the dewatering, the quantity of water to be abstracted and the amount of groundwater lowering in the surrounding area must be minimised. This paper describes the measures that have been taken on the Copenhagen metro project to achieve the objective of minimal environmental impact whilst still carrying out a major dewatering scheme.

Jan 1, 2000

By Jafar Safarian, Leiv Kolbeinsen, Stian Seim, Hossein Salehi

The present work aims to investigate the link between the oxidation and reduction of a weathered ilmenite concentrate in terms of phase transitions, microstructural changes, and element distribution. An ilmenite concentrate sample was pelletized and fired at 1000 °C in air, and as a result, the pellets were oxidized. The oxidized pellets were reduced by hydrogen gas at 1000 °C, which yielded almost complete metallization of the iron content of the pellets. The ore and the pellets were characterized in each step by XRD and SEM techniques, and distribution of elements and phases were investigated. Ilmenite, pseudorutile, and rutile were the main phases detected in the ilmenite concentrate sample, and depending on the weathering degree of the particles, different fractions of the phases were identified in their microstructure. It was found that irregular rutile grains dispersed in a pseudobrookite matrix is the morphology of the oxidized ilmenite phase. However, increasing microcracks and porosities were the only microstructural changes in the pseudorutile phase after oxidation in air. Studying the specific types of the ore particles and their oxidized and reduced forms indicated that the phase distribution in the ilmenite ore particles dictates the phase distribution in the oxidized and reduced ones. Results show that the morphology of the reduced particles includes a titanium (III) oxide matrix in which reduced iron globules are dispersed.

Feb 8, 2021

By James J. Scott

Research and development has been carried out on the patented Dynamic Rock Anchor, tradenamed DYNA-ROK and DYNA-ROK PLUS Anchors, which are manufactured and marketed by Ingersoll-Rand Company. This paper will present the results of field testing of this revolutionary new concept in ground control. Geologic conditions will be described where the plastic sleeve of the DYWA-ROK anchor alone is sufficient to provide anchorage and also, where in softer ground conditions, the DYWA-ROK PLUS is applied. The rationale for making the decision as to the type of fixture to be employed, the length of plastic tube to be used and the quantity of resin are explained. Pull test data will be shown from eight different coal seams in the Eastern United States where the product has been installed.

Jan 1, 1990

ABSTRACT Inco’s Iron Ore Recovery Plant was operated by Inco from 1955 to 1980 near Sudbury, Ontario. As exposures to specific nickel substances have been associated with adverse respiratory endpoints it is important to understand processes giving rise to such substances. This manuscript discusses the process and equipment, the propensity for aerosol formation, and operational procedures used by Inco in roasting a pyrrhotite concentrate, reducing the nickel in the formed oxide, leaching the nickel in ammoniacal solution, purifying the resulting solution, making green or black NiO, and producing iron oxide pellets. Industrial hygiene measurements are also reported.

Jan 1, 2013

By Jeremy Cawley, Jeff Murphy, Horry Parker, Brock Gaspar, Jake Keegan

The Lower Olentangy Tunnel project includes 47,000 cubic yards of planned ground improvement for earth pressure balance machine (EPBM) tunneling (5.2 km) and microtunneling (335 m) in glacial soils. Jet grouting started in late 2021 and will continue through 2023 to complete operations at 5 shafts, 14 safe havens, 5 watermain ground improvement zones, and a river crossing. Typical jet grout columns are installed at depths between 15–24 meters. Discrete soil-cement blocks range from 267–8,900 cubic yards in volume. This paper discusses the methodology, testing, and technical considerations associated with jet grouting operations in glacial overburden across an urban environment.

Jun 13, 2023

By Chengyi Ding, Xuewei Lv, Changyang Ji, Rende Zhang, Xiangwei Zheng

The fraction of liquid phase in sintered ore can be the most important factor to determine the sinter quality and yield in sintering process. The generation ability of liquid phase for mixture of iron ore powders is determined by basicity, roasting time, roasting temperature and chemical composition of iron ores. Five different iron ores were selected in this study and the dried powders of iron ore and CaO reagent (<200 mesh) were homogeneously mixed together at their required proportions, then 15g of the mixture was pressed under a pressure of 20MPa to make a cylindrical sample with a diameter of 20mm. The sintering temperature in this study was kept at 1280℃, the gas phase is air, the holding time was varied with its three levels of 5min,10min and 15min. After that, the sample was cooled under room temperature in the air, and the cooled sample was analyzed by using zeiss optical microscope. The mineral phase compositions were quantitatively determined with an open source image processing software, Image J whicn can calculate the fraction of liquid phase. Besides, the study on how to estimate the sintering behavior of the raw materials in different conditions by the theoretical calculation is of vital importance, and the development of this will greatly improve the sintering production. Factsage will be used to calculate the liquid phases formulation during the sintering. Comparing the experimental results and the theoretical calculation shows that the mass of liquid phase increases with increasing basicity during the sintering, besides, the mass of calcium ferrite increases with increasing basicity. The generation ability of liquid phase of iron ores can be predicted through the experiment verification.

Jan 1, 2015

By Reece Kurre, Gabriel Walton

"Roof bolting has long been used in underground mines across the world to provide ground support. Modern roof bolts are cheap and easy to install with the use of specialized machines as a part of the production cycle. Lhoist North America’s Crab Orchard Mine is an underground room and pillar limestone mine that uses mechanically anchored roof bolts for ground support. The mine currently employs two different roof bolting patterns: a standard 5 × 5 foot pattern, and a 2.5 × 2.5 foot pattern for use in areas with particularly hazardous roof conditions. The purpose of this study is to evaluate the relative effectiveness of each bolting pattern.A series of numerical models were created using RocScience’s RS2. The models were based on a symmetrical section of the mine at its deepest point, and were modeled using Generalized Hoek-Brown failure criterion along with a discrete fracture network. A series of sensitivity analyses were performed on the models by varying parameters such as joint friction angle, crack persistence, joint randomization, and tensile strength of the limestone. Based on the results of the original models and sensitivity analyses, it appears that the standard bolting pattern provides sufficient roof support capacity under almost all the expected conditions at the mine, since factors of safety below the design value of 1.5 were only found for individual bolts in a few of the worst test cases considered. These results can help improve the Mine’s productivity and reduce operating costs without compromising safety.INTRODUCTION AND CASE STUDY DESCRIPTIONLhoist North America’s Crab Orchard Mine is an underground limestone mine located in Crab Orchard, Tennessee. The mine is located under an 800-foot-high mountain, and outcrops on three sides. The mine is accessed through three separate portals and has two main levels, along with a partially developed third level. Extraction is accomplished by the room and pillar method using 50 × 50 feet pillars and 50 × 50 feet rooms. The mining height is limited to 50 feet to keep the pillar width to height ratio around 1.0. Each heading is excavated in a two-stage process that consists of a 30-foot-tall top heading and a 20-foot-tall bench. A distance of at least 30 feet is maintained between the two levels at all times (Crab Orchard Mine Technical Staff, 2017)."

Jan 1, 2019