Search Documents

By Márcio Nascimento Cunha

O aço inoxidável ferrítico 409 é um aço suscetível a grande quantidade de inclusões. Determinar a origem das inclusões não é uma tarefa fácil e o conhecimento dos processos que fazem parte das etapas de produção do aço aliados a um bom método de caracterização são pontos importantes na identificação da origem das inclusões e solução de problemas de qualidade. A proposta deste é trabalho caracterizar inclusões no aço AISI 409 em todas as etapas de produção na Aciaria utilizando técnicas de microscopia e análise química. Amostras do aço líquido e escória foram retiradas em cada etapa de produção. Análises de composição química do aço e escória foram realizadas através de espectrometria de energia dispersiva de raios X (EDS). As inclusões no aço foram examinadas através de um microscópio óptico com analisador de imagem, quantificadas e caracterizadas em termos de composição química no MEV-EDS. Os resultados mostraram que a composição química das inclusões modifica de acordo com o tratamento em cada etapa de processo e a condição de limpidez da corrida é afetada após adições de Ti no Forno Panela e no distribuidor do lingotamento contínuo.

Aug 16, 2017

By J. Nell

Heavy mineral deposits often contain relatively high levels of radioactive elements (thorium and uranium in particular).It is difficult to obtain clean separation of ilmenite and monazite (the main impurity mineral containing radioactive elements), and physical intergrowths of the two minerals are, in fact, not uncommon. As a result, ilmenite concentrates obtained from such deposits often contain high levels of thorium and uranium. Because of the large negative free energies of formation of ThO2and U3O8boththorium and uranium report to the slag during smelting and if an ilmenite concentrate contaminated with monazite is used to make high titania slag, the concentrations of these elements in the slag end up about 40% higher than in the ilmenite feed. Previous work, patented by RGC Mineral Sands Limited, and subsequently confirmed by Mintek, showed that radioactivity may be reduced by roasting an ilmenite concentrate with borax at 1000°C to 1100°C and leaching it with hydrochloric acid1. It is evident that the cost of an ilmenite roast/leach process will be high and there may be economic benefits in removing the radioactive elements from the slag instead (the volume of slag to be treated is smaller than the volume of ilmenite feed). To remove radioactive elements from the slag it is necessary to know how these elements occur in the slag. Inother words, the distribution of uranium and thorium between the various oxide, silicate and metallic phases in high titania slag must be determined. Once the deportment of thorium and uranium between the various phases ha sbeen determined, an appropriate process for slag purification can be developed. Test samples High-titania slag was prepared in a pilot-scale DC furnace from ilmenite concentrates with different levels of uranium and thorium. Subsequently, ten slag samples representing a range of compositions were selected for bulk chemical analysis, scanning electron microscopy and micro-analysis. The samples were crushed to a maximum particle size of 1 mm and from each sample a 20-kg batch was riffled out for analysis. Bulk chemical composition Chemical compositions of the samples selected for test work are given in Table I. TiO2, Al2O3, SiO2, MgO, MnO, FeO and V2O5were analysed by ICP-OES, Na2O, CaO andCr2O3by atomic absorption spectroscopy and U and Th by XRF (the XRF detection limit for U and Th was around 4 ppm). The ?B? series has a higher silica content than the others as a result of small silica additions that were made during smelting. All samples have elevated alumina levels as a result of furnace refractory contamination during smelting. As expected, there is an inverse relationship between the concentrations of TiO2and FeO in the samples (Figure 1).The TiO2and FeO levels are similar to the levels found in industrial slags2. Extreme conditions of reduction under which reduction of more ?refractory? oxides (e.g., chromia, magnesia, silica, alumina and even urania and thoria) might take place were not explored in the study. Note that BB1and BBB1 contain more than 7% combined silica and alumina (SiO2as a flux addition during smelting, and Al2O3from refractory contamination) and they do not fall on the general trend defined by the other samples. The U and Th concentrations of sample E2 is noteworthy. In the preparation of slag E2, monazite concentrate was added to the ilmenite to increase the concentrations of radioactive elements in the slag. This was done primarily to facilitate the detection of Th and U during the phase chemical characterization of the slag. Radioactivity measurements Gamma ray emissions from the samples were measured [ ]

Jan 1, 2007

By J. F. J. Thomas

"AbstractBoth the quantity and quality of waters available as raw materials are important to Canadian industry and to the national economy. The huge demands of many Canadian industries is illustrated by tabulated figures, based on the 1950 Canadian production of certain products, and on United States figures for the gallons of water required to produce a unit quantity of each product. It is suggested from comparison with American survey results and figures that Canadian industrial water consumption is 1 to 11/2 billion Imperial gallons per day. Since present information on Canadian usage is meagre and it is not certain that American survey results can be directly applied to Canadian industry, this estimate must await confirmation in future studies.The hydrologic cycle and the principal factors affecting the quantity and quality of water, namely, climate and season, topography, geology, vegetation, and human activities, are discussed and the principal salts dissolved in water which affect industrial use are enumerated.The present survey studies by the Mines Branch on water quality are outlined. Besides chemical analyses of municipal water supplies within a watershed, periodic sampling and analyses of major surface waters for a one-year period is being carried out. The importance of studies on seasonal variation in quality is stressed by comparing the dissolved salts in various river waters with river flow. Figures showing such relationships in the Rideau river and Ottawa river at Ottawa, the Columbia river at Trail, B.C., and the Battle river at Unwin, Sask., are presented. Different rivers show different quality changes with changing flow, and possibly only after long-term studies can the relationships be predicted.Quality studies on water may be as important as studies on many other raw materials. The quantity of the raw material, water, is not inexhaustible nor is the quality indestructible, and more realization of its importance, followed by conservation and intelligent use, is desirable."

Jan 1, 1952

By Ganesh P. Mohanty, James J. Wert

THE brittleness of the intermetallics usually render their deformation studies at ordinary temperatures using conventional techniques inadequate. On the other hand, although X-ray line broadening measurements is not a complementary technique, it provides a means for gaining limited but useful information on the cold worked state of these materials. In the present instance, a study of the effects of cold work in the lead telluride intermetallic compound was carried out by analyzing the diffraction profiles of the deformed and the corresponding annealed samples. An ingot of PbTe was prepared by induction melting high-purity lead and tellurium in a quartz crucible under an atmosphere of argon. After homo-genization, the ingot was ground to -325 mesh at room temperature, and using a polished die the cold- worked powder was pressed into the form of flat faced briquets for diffraction measurements. A spectrometer with 0.125 deg per min scanning velocity, CuKa radiation, pulse height analyzer, and a proportional counter were employed in the X-ray measurements, and the powder peaks were collected from the sample in fully cold-worked state and after it had been annealed to relieve the effects of cold work completely. For reliable estimates of the peak extremities, small angular ranges where the tails merged into the background were point counted. Fourier inversions of the experimental peaks were carried out in an IBM 705 computer using the procedures introduced by stokes.' Both the cosine and sine components of the Fourier series were used to take into account any peak assymetry arising

Jan 1, 1963

By Edney da Silva Dias, Leticia Fuchs, Walter Coan, Rodrigo Deperon, Eduardo Kuhl, Fernanda Jansen, Micael Leandro

O objetivo deste trabalho é apresentar um projeto desenvolvido para maximizar a taxa de ocupação dos veículos que carregam na ArcelorMittal Vega, por meio da utilização de programação linear combinada com métodos de automação de processos robóticos (RPA - Robotic Process Automation), de modo a atender todas as premissas do modelo de expedição de cargas, tais como: restrições de clientes, capacidade máxima por tipo de veículo e distribuição de volumes para as transportadoras de acordo com as metas acordadas. O uso de ferramentas de otimização e automação, integradas ao ERP (Sistema Integrado de Gestão Empresarial), utilizado pela empresa, permite realizar o processo de programação de transportes em massa, obedecendo multicritérios. A ausência de ferramentas que auxiliem neste processo, impacta diretamente na produtividade, na capacidade intelectual dos recursos alocados, na taxa de ocupação dos veículos, na capacidade de expedição da fábrica e no nível de serviço ao cliente. Visando aumentar a eficiência nos processos, melhorar a taxa de ocupação da capacidade dos veículos e consequentemente a capacidade de expedição, foi implementada a solução para aperfeiçoar o processo de programação de cargas e agregar valor ao negócio quanto a entrega ao cliente final.

Oct 1, 2019

By M. J. Shulman

The exploration geologist is frequently confronted with the problem of allocating his resources, i.e., exploration effort, among various areas. Although geologic, financial and logistic considerations influence the allocations, no objective criterion is usually given which determines the optimal allocation. Maximizing the gain in information, subject to the constraint of a limited exploration budget, is used as the objective criterion to allocate reconnaissance effort. The information function, I(x), quantifies the expected gain in information, where x is the scale of exploration. To calculate the information function the following data are necessary: 1. The probability that an area contains a target must be estimated. 2. For each scale of exploration, four probabilities must be estimated: the probability that an anomaly is produced by the target; the probability that an anomaly is not produced by the target; the probability that an anomaly is produced by a barren area (false signal); and the probability that an anomaly is not produced by a barren area. Alternatively, the barren area can be replaced by other targets. To illustrate the allocation model, the optimal number of line kilometers/line spacing per area is determined for an aeromagnetic survey for iron in Egypt.

Jan 1, 1985

By C. T. Liu, J. Gurland

The deformation behavior in tension of spheroidized carbon steels was studied at room temperature as a function of carbon content, 0.065 to 1.46 wt Pct, and carbide particle size, 0.88 to 2.77 p. It was found that the Hall-Petch strength-grain size relation is directly applicable to the yield and flow stresses of the two lower-carbon steels , 0.065 and 0.30 pct C. The strength data for the medium- and high-carbon steels, 0.55 to 1.46 pct C, also satisfied the Hall-Petch relation, provided that these data are based upon the particle spacing. Beyond 4 pct strain, the flow stress data of all the steels studied could be represented by the same Hall-Petch relation with dinerent spacings for grain boundary and particle strengthening. The behavior of the higher-carbon steels was consistent with the postulated formation of a dislocation cell network during processing and initial deformation (up to 4 pct strain). The cell size was assumed to be equal to the planar particle spacing. The true stress at the ultimate tensile strength was also found to be a function of the particle spacing. At a given temperature and strain rate, the yield and flow stresses of carbon steels depend on the type and dimensions of the microstructure. Starting with the work of Gensamer et al. in 1942,' experimental studies on pearlitic and spheroidized carbon steels revealed that the strength of steels is a function of two main parameters: the ferrite grain size2'3 and the carbide particle spacing;1'4'5 on this basis, two different strengthening mechanisms have been developed to apply to steels of low and high carbon contents, respectively. In polycrystalline iron and mild steels the grain boundaries are regarded as the major structural barriers to slip. The relation between strength and grain size is generally represented by the Hall-Petch equation which is based on a linear proportionality between strength and the inverse square root of the average grain size.2'3y677 However, Gensamer et al.' and Roberts et related the yield strength of medium -and high-carbon steels to the carbide particle spacing alone, and they found a linear relation between the logarithm of the mean free path in the ferrite and the yield strength in both spheroidized and pearlitic steels. By means of the electron microscope, Turkalo and LOW' extended the study to finer structures; they concluded that the logarithmic relation is not valid for the entire range of microstructures unless grain boundaries are also included in the measurement of the mean free path. For the specific case of spheroidized steels, Ansell and aenel' found that the yield strength data,4'5 when plotted as a function of mean free path, fit the Hall-Petch equation; however, T'ysong found that the same data fit the 0rowanl0 relation if a planar inter-particle spacing is used. Recently Kossowsky and ~rown" studied the strength of prestrained spheroidized steels, 0.48 and 0.95 pct C, and concluded that the strength due to the carbide dispersions varies linearly with the reciprocal of the square root of the mean free path between carbide particles and dislocation networks. Such networks were first observed by Turkalo." The conclusion common to all these studies is that the available slip distance in the ferrite is the most important variable in determining strendh. Previous work on carbon steels is restricted to limited composition and strain ranges. The mechanism which governs the flow properties is not clearly understood, and, in particular, little is known about the composition dependence of the transition between grain boundary strengthening and particle hardening. The purpose of the present work is to investigate the strengthening mechanism in spheroidized steels over a wide range of carbon content, 0.065 to 1.46 wt pct, and plastic strain, yielding to necking. The spheroidized structure was chosen because of its relative simplicity and the relative ease of control and measurement of the structural parameters. The experimental work is limited to tensile testing at room temperature at constant extension rate. The effects of the carbide particles on the fracture behavior of spheroidized steels are discussed elsewhere.13 EXPERIMENTAL PROCEDURE Eight different grades of vacuum-cast carbon steels were supplied in the form of forged and rolled plate by the Applied Research Laboratory of the U.S. Steel Corp. The compositions furnished with these steels are given in Table I; the carbon content ranges from 0.065 to 1.46 wt pct, or from 1.0 to 22.3 vol pct of carbide. The steel plates were cut transversely into rods a little larger than the test specimens, 1 in. gage length, i in. diam. The rods were austenitized in air (enriched with CO by a consumable carbon-rich muffle) at 50° C above theA, orA., temperature for 2 hr and then quenched in oil with vigorous stirring. The as-quenched rods were tempered in two stages in order to obtain the desired distributions and sizes of carbide particles. The rods were first tempered at 460° C for 10 hr and then at 700" C for periods ranging from 4 hr to 3 days, in vacuum. After final machining, all specimens were vacuum-annealed again at 650°C for 1 hr in order to relieve residual stresses. The tension tests were carried out in two steps. The initial part of the load-strain curve, up to about 2 pct strain, was determined on a Riehle testing machine with an extensometer of small strain range, 4 pct strain, in order to obtain the yield and initial flow piopertiesi As soon as the first part of the test was finished, the specimen was placed in an Instron testing machine equipped with a strain gage extensometer with a maximum strain range of 50 pct. The load-strain curve to fracture was

Jan 1, 1969

By Jamal Rostami, Asok Ray, Samer S. Saab Jr., Wenpeng Liu

Ground instability, such as roof or rib failures, is one of the most serious and frequent safety hazards that occur in underground mining, tunneling, and underground construction. The ground-related parameters and features of interest, in assessing roof or rib failures, are location, frequency, and orientation of the joints, voids, as well as rock-strength. These parameters are the main components of rock mass characterization that offers effective strategies for ground support, which, in turn, allow one to mitigate the risks related to ground instability. The main objective of this study is to determine the location of joints and classify rock-strengths by analyzing the drilling data recorded from an instrumented roof bolter while drilling for rock bolt installation during the operational cycle. For this purpose, computer programs based on updated pattern recognition algorithms were developed for joint-detection and classification of rock types to offer an estimated strength. This paper briefly introduces ongoing research on joint detection, especially for joints with an aperture less than 0.125in (3.175mm), by employing an instrumented roof bolter in controlled environments. To improve the capability and precision of joint detection programs in detecting the joints from the drilling data and reducing the number of false alarms, many laboratory tests with various simulated joints and rock-strengths were carried out at a J.H. Fletcher & Co. facility. This paper reviews testing procedures, data analysis, updated algorithms used for joint detection, and discusses the latest round of testing in samples with simulated joints at various angles along the borehole.

Jan 1, 2017

By John P. Dunford

Ground support continues to be the most important safety consideration in underground mining. The Bureau of Mines has developed a yielding steel post with a capacity of 45 tons and b c1osure allowance of 24 inches in a 6 to 7 foot seam height. The post mechanism in a three piece unit consisting of a top and bottom leg made from standard steel pipe and a separate foot bracket. It develops its load carrying ability when the lower pipe, with an attached interference ring, is forced into the larger top leg. The walls of the top leg are deformed radially and along the axis. Yield continues until the unit bottoms out. Other advantages of the post is that due to its simplicity it can be made at the mine shop level and its cost should be about one-hundred dollars. Prototype units were tested in the laboratory. Based on these results, modifications were made that would make the post perform better as a mine support. Two field tests were conducted. The first test used the units as supplemental support for the wood crib rows in a longwall tailgate. The second and larger field teat had 84 posts placed on salvaged track rails. They were installed on two foot centers in the middle of the entry. Overall the supports functioned well during use in the headgate entry, but problems with the quality of some of the pipe caused localized failures. However, these problems can be attributed to one manufacturer of pipe and through tighter specifications can be eliminated. The use of the posts with the rails is showing additional benefits as a ground support system. By providing continuous support between the posts a beam is created that has much more load bearing. The additional support can reduce floor heave and in some cases eliminate the need for the rib side crib line.

Jan 1, 1986

By H. O. Hofman

(Canal Zone Meeting, November, 1910.) I. INTRODUCTION. IN a previous paper,1 The Behavior of Calcium Sulphate at Elevated Temperatures with Some Fluxes, we published the results of our investigation, into the behavior of calcium sul-phate in air; that, is, under oxidizing conditions. The results as a whole hold good for a neutral atmosphere, or one which has no chemical effect upon calcium sulphate. The present paper deals with the behavior of calcium sulphate under reducing conditions, the reducing-agents employed being carbon monoxide and carbon, and the changes the calcium sulphide formed undergoes when it is subjected to an oxidizing-roast. Technical literature deals very sparingly with the subject. The information furnished by the recent leading chemical manuals is general. Thus Dammer,2 Moissan,3 and Abbegg,4 quote Berthier as having reduced, in 1823, calcium sulphate with carbon, and Stammer as having done the same in 1851 with carbon monoxide; Gmelin Kraut 5 add Leplay and Laurent (1848) as third investigators. Metallurgical authorities confine their statements to the known fact of reduction by carbon. II. PREPARATION OF RAW MATERIALS. 1. Calcium Sulphate.-This salt was prepared in the same manner as described in our previous paper,6 and was found to be chemically pure. * Professor of Metallurgy, Massachusetts Institute of Technology. + Metallurgical Instructor, Imperial Technological Institute. 1 Trans, xxxix., 628 to 653 (1909). 2 Handbuch der anorganischen. Chemie, vol. ii., part 2, p. 309 (1894). 3 Traité de Chimic Minérale, 1904, vol. iii., p. 543. 4 Handbuch der anorganischen Chemie, vol. ii., part ii., p. 116 (1905). 5 Handbuch der anorganischen Chemie, vol. ii., part 2, p. 233 (1909). 6 Trans., xxxix., 630 (1909).

Nov 1, 1910

By K. B. Rojiani

Surface mining activities disturb large tracts of land resulting in the potential for greatly increased downstream sediment loads. The Surface Mining Control and Reclamation Act of 1977 places increased emphasis on the protection of the environment from the adverse effects of surface mining operations. Surface mining activities must be planned to minimize disturbance to the hydrologic balance, erosion and sediment contributions to receiving streams. Sediment ponds must provide a sediment storage volume equal to the accumulated sediment volume from the drainage area as determined by the Universal Soil Loss Equation (USLE) or other empirical methods established by the regulatory authority. It has thus become extremely important for the mining industry to secure more accurate estimates of potential erosion losses and sediment yield. Accurate estimates of sediment yield are required for the planning, design and successful operation of sediment control systems such as detention ponds and other alternative control structures and for evaluating the effectiveness of land management practices. The principal soil loss prediction procedure available for use is the LISLE. The USLE procedure is inadequate for use in predicting soil loss from surface mine regions for a number of reasons. These include: 1. The USLE was developed to estimate average average annual loss from agricultural soils. It cannot predict accurately soil loss for specific storm events. In surface mine regions a major portion of the soil loss occurs during the initial six months to one year of active mining. Accurate estimates of soil loss over short periods are thus required for the design of control structures. 2. The slope length and gradient factors used in the USLE were obtained from data or cropland having slopes ranging

Jan 1, 1983

By Eckley B. Coxe

I wish to call the attention of the Institute to a peculiar variety of anthracite which occurs in the Buck Mountain vein at our collieries at Drifton, and in the same and other veins in different localities in the anthracite coal-fields. It is known among the workmen as iron-gray or cast-iron. It has a dull, greasy appearance, as if a piece of ordinary anthracite had been rubbed with a dirty and greasy rag and allowed to dry. It was formerly considered a very impure coal containing a high percentage of ash, and was picked out of the coal and thrown away. But the following analysis of it and of its ash, made by Mr. J. Blodget Britton, of Philadelphia, shows that such is not the case, the percentage of ash not being much higher than that of the ordinary anthracites as they are prepared for market. ANALYSIS OF COAL. Water,.........4.36 Fixed carbon, by difference,.. 84.90 Volatile combustible matter,. . 3 48 Ash,..........7.26 100.00 The carbon proved to some extent to be of the nature of graphite, and slowly combustible. ANALYSIS OF ASH. Silica,.........25.66 Sulphur,........ .17 Alumina,........27.03 Phosphoric acid,.......21 Ferric oxide,.......42.83 Alkali, undetermined matter and Lime,.........1.56 loss,.........60 Magnesia,........1.83 Manganous oxide,......11 100.00 We recently collected a quantity of the substance and made a fire with it, in an ordinary stove, which was kept up several days. We found that it burned with intense heat, and apparently as freely as our other coal does. Mr. Britton is probably right in his view, that the difference in appearance is not due to impurities in the coal, but to the fact that the carbon is in a more or less graphitic form, as many of the standard coals are no purer. I bring this before the Institute as I know that a large quantity of this valuable fuel is thrown away every year, on account of its supposed impurities.

Jan 1, 1879

By Daniel K. Lindberg, Fiseha Tesfaye

To reduce the use of fossil fuels and increase self-sufficiency in energy, nowadays, there is an increasing interest to produce heat, power and transportation fuels from renewable resources. Solid biomass is one of the most important renewable energy sources for meeting this target. However, fouling, slagging, and corrosion threaten long-term operation availability and costs of biomass power plants. Slags accumulated on the surfaces of superheaters, which decrease thermal efficiency, often constitute a considerable percentage of complex inorganic phases. However, thermodynamic properties of the complex inorganic phases and their combined effect, which will help to deal with the slag related problems during high-temperature biomass combustion processes, are not well known. In the present paper, thermodynamic properties of K-, Ca-, and Na-based inorganic phases and their mixtures under different gas conditions are both critically reviewed and experimentally studied. The obtained results are presented and discussed.

Mar 1, 2017

By Lina Maria Varón Cardona

A utilização de briquetes de misturas de carvão fóssil e biomassa em substituição ao coque como agente redutor pode contribuir para a diminuição das emissões de CO2 à atmosfera no processo de fabricação de ferro através da substituição de parte do carvão fóssil por carvão vegetal. O objetivo deste artigo é identificar quais são as principais variáveis que influenciam a produção de briquetes de alta qualidade a partir de misturas de carvão fóssil e carvão vegetal. Os briquetes foram fabricados em matriz cilíndrica, compactados em prensa hidráulica e tratados termicamente em forno vertical aquecido com resistência elétrica sob atmosfera de nitrogênio. Foi investigada a influência da composição da mistura, da taxa de aquecimento e do tamanho de partícula do carvão fóssil. Os briquetes com composição na faixa de 10% a 15% de carvão vegetal moído e peneirado em partículas menores que 325 mesh apresentaram maior resistência à compressão. Foi observado que o efeito do envelhecimento do carvão influencia na qualidade do briquete, pois diminui sua resistência à compressão; as dimensões finais dos briquetes após tratamento térmico diminuíram quando a velocidade de aquecimento é menor; ao se aplicar maior velocidade de aquecimento os briquetes apresentam inchamento.

Aug 1, 2018

By Dan Nilsson

The Luossavaara "Research Mine" is the First large, offensive effort in mining research conducted by the Swedish state. Over a 5-year period, 1981-1985, the Swedish Mining Research Foundation works in the "Research Mine" on the development of mining systems and equipment. The purpose is to bolster the competitive strength of the Swedish mining and mining equipment industry. The previosly abandoned Luossavaara mine in Kiruna, in northern Sweden, has been reopened especially For the project. Ore is mined and sold during the course of the research project. The income from the sales covers a large portion of the costs for teh research.

Jan 1, 1985

By T. P. Lim, A. J. Vivyurka, N. K. Davé

Chemical and radioisotope stratification studies were carried out in an abandoned uranium tailings pile at Elliot Lake, Ontario, Canada. The tailings, with an average thickness of 7 m over an area of 16 hectares, were deposited approximately 20 years ago on a layer of black peaty material which overlays deposits of permeable glaciofluvial sands. Geohydro-chemical investigations of this tailings area have been ongoing since 1978. The radioisotope profile study was conducted on three adjacent sites. Solid core samples, collected with a split spoon sampler at various depths, were analyzed for various chemical and radioisotope constituents. The results indicated by 2 distinct zones of stratification; an upper zone, where the constituents were uniformly distributed, and a lower zone, near the peat-tailing interface, which showed increasing concentration with depth. Within the peat layer, the concentration decreased rapidly with no significant levels of contaminant penetration below the peat layers observed, though the samples were limited. The pH profile showed that the top 5 m of the tailings have been oxidized, the average soil pH in this zone was 3.4 compared to 5 .8 underneath it. The groundwater hydrology of the system was observed to be complex showing downward and lateral flow in the dry season and lateral and upward flow during the spring and periods of heavy rainfall. The results are discussed in terms of a model based on the combined segregation and settling process of the tailings fine fraction, and the geohydro-chemical interaction of the solid and liquid phases.

Jan 1, 1981

By T. E. Sedysheva

The study of Co-rich manganese crusts has reached the level which allows to start prospecting works in the observable future, and furthermore, probably, exploitation of ore deposits. In this connection, among other goals, the necessity to analyze a distribution of ore bed parameters in details is quite urgent. Foremost, these are crust thicknesses in connection with landforms and elements of submarine mountains relief. This report is based on representative sampling made in course of research cruises run by SSC Yuzhmorgeologiya over guyots of the Magellan Seamounts. Crustal covers could overlie seafloor surfaces which are confined to a various landforms and elements of relief under the condition, that they are free of sediments. These are planed parts of a summit surfaces, edges, spurs, rectilinear parts of slopes, intermountain saddles and volcanic edifices. It is known, that crustal thicknesses are different at a various forms of relief [1]. We processed statistically the data around crustal thicknesses, which were sampled by dredging and submersible drilling (Tables 1, 2).

Jan 1, 2010

By E Cunha, D Roldao, TáTamantini, J F. C L Costa, T Webber, C Monteiro

The main problem of geostatistical simulations is to reproduce the real characteristics of the mineral deposit when there are few conditioning data. In this case, the geological interpretation, based on structures, geophysics and geological maps, plays the major role in terms of resource evaluation.The paper investigates the use of principal component analysis (PCA) to help classify multiple geostatistical categorical simulations considering the similarity among them and the interpreted model, herein referred as training image (TI).An iron deposit with four lithological facies, in a specific horizontal plane, was used as case study for two-dimensional (2D) simulations. Sequential indicator simulations (SIS) was used to obtain ten equally probable 2D images, which were generated and compared against the interpreted model (TI).In this study, 11 random variables are comprised by the vector of ten SIS realisations plus the training image (TI). The similarity between the TI and each SIS realisation is measured using the angle between the TI and SIS vectors projected in the new coordinate systems (PCA factors). It is possible to order the SIS realisations from the highest to the lowest PCA factor taking into account the TI similarity.The visual analysis of the images shows coherence in the PCA results as a method to measure similarity. This methodology can be used as a post-processing tool to rank simulation results and to select the ones which better represent the prior known geology or to compare the quality of different methods of simulation.

Sep 26, 2011

By Krishnendu Mandal

"For a multi-story building project in Kolkata, a pile load testing program was conducted to minimize pile performance uncertainty resulting from variable subsurface conditions and to verify the pile load vs. settlement response. The program consisted of performing five (5) instrumented load tests on augured cast-in-place (ACIP) pre-production test piles. Vibrating-wire strain gages and extensometers were installed in the test piles at strategic locations to enable measurements of the load vs. deformation behavior of the test piles. This paper presents a description of site subsurface conditions, test pile installation, instrumentation setup for a maintained load test (MLT), static compression pile load test results, and pile instrumentation result interpretation. Average mobilized unit shaft resistance values are calculated.2.0 INTRODUCTIONThe project site is located in Kolkata, near river Ganges, and the proposed development plans consist of constructing six (6)25-story (G+25) towers; see Fig. 1 and Fig. 2 below for approximate site location and proposed development layout, respectively. The buildings were designed to be supported on ACIP piles. A field load test program was implemented to verify sub-surface conditions and pile design. The test program consisted of installing Five (5) instrumented test piles numbered LP1A and B through LP6A and B, and performing static compression load tests on these piles. The piles were instrumented with vibrating-wire strain gauges and extensometers, so that the pile shaft resistance distribution along pile length and the pile toe resistance could be interpreted using direct instrumentation measurements."

Jan 1, 2015

By D Rattray, D Macfarlane, I Robb, N Halpin, G T. Dale

Mining faces many environmental, social and regulatory liabilities of which water management is just one. Others include site rehabilitation, carbon emissions, biodiversity offsets, strategic cropping land, subsidence, and noise and dust generation. Management of these liabilities is commonly seen as a cost of doing business and each is often independently addressed, bypassing the opportunity to reduce costs through integrated approaches. Furthermore, approaches to dealing with these liabilities tend to be constrained by a prevailing culture of engineered solutions and lack of appreciation of risk associated with alternative and hybrid alternative-engineered solutions. Suboptimal outcomes can also be reinforced by rigid regulatory constraints. While the cost of addressing operational liabilities may be a small proportion of overall mine management costs, failure to do so effectively may influence social licence to operate and, as recently demonstrated by the decision of the NSW Land and Environment Court to block expansion of the Warkworth Mine near Singleton, absolute licence to operate.Integration of environmental, social and regulatory liabilities with value-creating and risk-reduction opportunities such as beneficial water use, carbon bio-sequestration, habitat connectivity, keyline farming, improved grazing design and management systems, windbreaks and visual screens, presents opportunities to reduce risk and create value. This potential may achieve overall improved outcomes in both economic and non-economic mine performance criteria.Two case studies in beneficial use of waste water from the mining and coal seam gas (CSG) sectors (which operate under different legislation) will be used to illustrate the potential to address mine development, operational and closure liabilities by understanding opportunities to reduce risk and create value through a holistic water management framework. The technical requirements and alternative approaches to beneficial use of mine water are addressed, along with the direct economic benefits for mine operational costs and opportunities to positively engage communities and build resilience into social licence to operate. Regulatory barriers to achieving improved outcomes will be discussed.CITATION:Dale, G T, Robb, I, Halpin, N, Macfarlane, D and Rattray, D, 2013. Opportunities for integrated mine management to minimise risk and create value, in Proceedings Water in Mining 2013 , pp 227-234 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013