Search Documents

By Michael H. Inglis

The Technology Application Center, in conjunction with the U.S. Bureau of Mines Liaison Program, is studying the use of Landsat data for the monitoring of coal surface mine reclamation activities. Landsat may provide sufficient information to reduce the number of on-site inspections now required. The focus of the project has been the Navajo Coal Mine located in north- western New Mexico and operated by Utah International, Inc. On October 15, 1977, a field team recorded spectral measurements at the mine during the time of Landsat's overpass and a corresponding aerial photographic flight. Training sets were selected from the ground and aircraft data representing vegetated, graded, ungraded and natural environments. A supervised classification of the data was performed by the Stanford University Remote Sensing Laboratory then correlated to aerial photos and mine maps. The results, to date, have been very encouraging.

Jan 1, 1979

By J. F. Brune

"Re-occurring face ignitions in U.S. coal mines are concerning and require a closer look at air quality monitoring systems and practices employed in these mines. The explosion disaster at the Upper Big Branch mine in West Virginia in 2010 caused 29 fatal injuries and was largely caused by inadequate water sprays and inadequate ventilation monitoring. In this comparison, the author compares ventilation system monitoring in Australian, German and U.S. underground coal mines and makes recommendations for improvements and best practices. Mines in Germany and Australia are adhering to more stringent requirements for monitoring air quality and quantity and for monitoring water spray systems on cutters to prevent frictional ignitions. Air quality should to be monitored for sufficient oxygen, toxic gases, explosibility and for fire gases indicating a potential fire. Ventilation monitors must also confirm that sufficient quantities of air are available. Fully automated, continuously recording atmospheric monitoring and alarm systems are established practices in Germany and Australia and should be mandated for U.S. mines as well, in addition to the current, regular spot inspections of the ventilation system by certified mine examiners. BACKGROUND: METHANE EXPLOSIONS, FACE IGNITIONS AND NEED FOR AIR QUALITY MONITORING Accumulations of methane in face areas of underground coal mines frequently lead to ignitions that can cause burns, traumatic injuries and, in the case of the 2010 Upper Big Branch disaster, cause major explosions with multiple fatalities. Table 1 shows the number of reported face ignitions in U.S. coal mines between 2010 and 2014, based on statistical data published by MSHA (MSHA 2010 – 2014). Although there appears to be a downward trend in such ignition incidents over time, ignitions continue to occur with some regularity; and each ignition may cause a potentially catastrophic mine explosion.Per regulation, all U.S. coal mining machinery, continuous miners and longwall equipment, is outfitted with continuously monitoring methane sensors wired to cut power to the equipment as the methane level exceeds 1%. Face ignitions keep occurring because these sensors are usually not positioned in sufficiently close proximity to the coal cutting drums or to the freshly exposed coal face where the methane is most likely released. Therefore, methane may accumulate in explosive concentrations near the coal face and the cutting drums long before the gas concentration reaches the 1% level near the monitor and creates an alarm."

Jan 1, 2016

By Sandeep Kumar Jeripotula, Govinda Raj Mandela, Aruna Manglapady

The main aim of this work is to evaluate whole-body vibration (WBV) of dozer operators based on three sitting postures (i.e., with 15° lean forward inclination posture, vertically erect posture with no inclination, and with 15° lean backward inclination posture) in Indian surface coal mines. A seat pad tri-axial accelerometer was used to collect WBV data from six dozer operators for three different sitting postures. Results showed that except for Dozer-1, 2, 4, and 5 operators during lean forward sitting posture and Dozer-4 operator during vertical erected posture, no other dozer operators have exceeded an exposure limit value (ELV) of 1.15 m/s2 in any of the considered sitting postures. Similarly, the vibration dose value (VDV) based on exposure action value (EAV) of 9.1 m/s1.75 has surpassed for all the dozers. But no dozer operator has exceeded an exposure limit value of 21 m/s1.75. The outcome of the study infers that based on “above health guidance caution zone (HGCZ)” for daily vibration exposure, i.e., A(8) measurements, for the operator sitting in lean backward postures the vibration amplification was reduced by 32.89% less compared with lean forward posture and 16.23% less when compared with vertically erected posture. Similarly, based on VDV(8), the exposure to vibration for the lean backward posture was reduced by 33.34% when compared with lean forward posture and 17.11% less when compared with vertically erected posture. Based on the above observation, it is concluded that lean back inclination with a trunk flexion of 15° is a favorable sitting posture, as it exposes the dozer operators to minimum vibration.

By Yong J. Kim, J. M. Park

"Solid/melt interface shape during continuous casting process has a strong influence on the resulting microstructure of the ingot. The interface shape is primarily governed by the heat flow condition between the molten metal and mold (or container). The roll of the microstructural transition resulting from various solid/melt interface shapes is discussed using the Sn-22.6wt%Pb alloy. Three different types of mold such as cold mold, resistantly heated mold, and electromagnetically heated mold were used to generate those interfaces having different curvatures. Experimental measurements of complete temperature profile along the axis and surface of the ingot during downward continuous casting are presented to determine the solid/melt interface geometry. The results provide an explanation of the ingot property with emphasis on microstructure.IntroductionA large scale of continuous casting process of alloys often has a rather deep V channel type of solid/melt interface resulting from a limited heat flow condition. As a result, the deep V type solid/melt interface shape entraps defects such as pores and inclusions and also creates canter segregation. In order to reduce the defects concentration, electromagnetic stirring(EMS) mechanism has been applied to the melt in the channel[l]. Speith and Bungeroth introduced first experimental EMS device to the continuous caster in 1952.[2] Today, with wide ranges of benefit, a large variety of such technique is available. Electromagnetic field on the melt can be divided into three aspects. First, eddy current is induced on the metal surface by alternating magnetic field with high frequency, which results in heating the metal. Second, electromagnetic body force which is generated by the magnetic field and the eddy current reduces the melt pressure on mold or support the melt not to contact with the mold[3,4,5]. This force is used for electromagnetic casting process(EMC). Finally, it causes stirring in the melt. Many research efforts have been done on the EMC process to improve surface quality of slab[6] and control meniscus shape where three phases such as melt, solidified metal, and mold powder coexist[7,8]. However, the eddy current heating effect on the surface of the ingot was less considered. It is worth noting that induced eddy current on the surface of slab melts the solidified shell and thus changes the heat flow condition between the mold and melt. Mold heating effect was first proposed by A. Ohno[9] and its processing conditions were identified in details[ 10, 11]. The so-called Ohno process is based on the fact that by keeping the mold temperature slightly above the melting temperature of the liquid, no grain can be nucleated on the mold wall[12]."

Jan 1, 1998

By J. -Y. Jia, G. -B. Qiu, C. -G. Bai, D. -F. Chen

Due to the great importance of the smelting process, it is essential to establish a calculation model on the viscosity of the slag system containing titania. In this paper, the calculation models of mass action concentrations and viscosity for the CaO-SiO2-TiO2slag system have been established according to the coexistence theory of the slag structure, as well as the referenced viscosities ofCaO-SiO2-TiO2at different temperatures and TiO2compositions. With the two models, corresponding calculated programs are made by means of programming language Matlab5.3, and the curves of viscosity of the TiO2concentration (?TiO2/%) at 1400°C, (R=0.9~1.0) are plotted. The results show that mass action concentrations of TiO2increases with increasing percentage ofTiO2, while the viscosity of CaO-SiO2-TiO2system is decreased. The results show that the models are in good agreement with the experimental and referenced data. They also shows that the models are reasonable for the CaO-SiO2-TiO2slag system. Keywords: coexistence theory; CaO-SiO2-TiO2slag system; viscosity ; calculation models.

Jan 1, 2004

By A. C. Elliott, A. J. Lafreniere

THE Hamilton Works of The Steel Company of Canada is a fully integrated steel plant with an annual capacity of three million tons. Located on the south shore of -Hamilton bay, it is in the centre of Hamilton's industrial belt. The heavy concentration of industrial activities found in this area, accompanied metallurgical well-known sources of pollution which are normal to urban areas is creating a pollution problem which concerns both industry and the general public. The Steel Company of Canada has recognized this problem and, accordingly, has adopted the policy of integrating suitable pollution control devices into its new installations. Much effort is also being expended to control the emissions of air contaminants from the existing equipment. At the Hamilton Works, there are two main sources of metallurgical dust emissions to the atmosphere -the Open Hearth furnaces and the Sinter Plant. Of these two, the Open Hearth furnaces are, undoubtedly, the largest single source of

Jan 1, 1962

By J. H. Daniel, S. Krzemien

Partners In Economic Reform, Inc., established a Polish-American Mine Center in Katowice, Poland, in 1996 to improve working conditions in the minerals industry. The program was based on the experience of mining companies, government, and labor in the United States, and was executed by a Coordinating Committee headed by the Center Director and Polish leaders from industry, State, labor, and academia. The cooperation among all parties has enabled safety and health issues to become part of industry restructuring with impressive initial reductions in coal mine fatalities. Existing work practices and attitudes of labor and management were assessed in coal mines throughout the country. Promotion, Rules, and Job and Task Analysis were identified as the areas requiring the most improvement, and are part of a post-graduate Safety Management program. Demonstration projects included measuring dust levels, using safety glasses, and promoting hazard awareness. Improved labor-management relations increased cooperation allowing for effective transfer of technology. Results can also be applied to improve the working environment of the manufacturing sector also undergoing restructuring.

Jan 1, 2001

By Dave Bulled

"This paper describes the design of an SABC grinding circuit using CEET technology applied to grindability data produced from testing 100 samples and distributed across the blocks of a mine plan using a geostatistical approach. The data distribution required the identification of the location of the sample points and a geological plan of the 130 million ton Ruby Creek orebody together with a mine plan of about 11000 blocks to be mined during the proposed 18 year life of the mine. The mill design was then made with consideration for the estimated hardness of each block in terms of both SAG and Ball milling with allowance for annual periods when the ore is harder to grind. Operating specifications were selected to achieve an optimum of capital and operating costs through use of the CEET program. The geostatistics assigned the statistical error that arises from having a limited amount of sample testing data to the hardness estimate of each block of ore in the mine plan. The final design could then include a quantification of risk and determination of safety factors based on the accuracy of block hardness estimates and CEET model fitting.INTRODUCTIONThe traditional approach to plant design involves the extensive testing of a single large composite sample or a small number of composite samples that are reputed to represent the ore body. It is accepted that the tests used can accurately measure in the laboratory the grindability of the sample by a process representing that to be used in the plant. The size of equipment required to achieve a specified throughput and product size is then calculated from one of a variety of models that have been developed by metallurgists over years of trial and error. Since these tests and models are tried and tested, they are accepted as reasonably precise; however during the operation of the resulting plant the design is sometimes found to be inadequate. It is then suspected that the flaw in the design process lies in the samples not being sufficiently representative of the ore body, since using only a single or small number of composite samples does not recognize the variability of the hardness of the ore, nor does it allow for the lack of precision in the hardness value used in the design.This paper outlines a design procedure suited to an orebody that is described by a geostatistical analysis of a reasonably large number of small samples of drill core. The analysis required the identification of the location of the sample points and a geological plan of the orebody, together with a mine plan of the blocks to be mined during the proposed life of the mine. The mill design was then made using the estimated hardness of each individual block with an allowance for annual fluctuations in the grindability of the ore. The geostatistical analysis assigned a statistical error to the hardness estimates of blocks and of each production year such that the final design included risk estimates and safety factors based on the possible errors that arise from having a limited amount of sample data (Kosick et al. 2002)."

Jan 1, 2007

By Ricardo Burdisso, Rahul Kadam, Kyle Schwartz, Marty Johnson

Occupational exposure to hand transmitted vibration (HTV) arises from the hand held powered tools extensively used in the mining and construction industry such as rock drills, chipping hammers, chain saws etc. Regular exposure to HTV is the major cause of a range of permanent injuries to human hands and arms which are commonly referred to as hand-arm vibration syndrome (HAVS). In addition to this, the percussive tools generate overall sound power levels in excess of 110dBA in most cases. Such a high sound power level greatly exceeds the maximum permissible exposure limit (PEL) of organizations such as National Institute for Occupational Safety and Health (NIOSH) and the Occupational Safety and Health Administration (OSHA). Long term occupational exposure to this noise has been diagnosed as the main reason for permanent hearing loss in the operators. It is therefore important to develop an understanding of the mechanisms which lead to these high vibration and sound levels and in order to do this a detailed computational model of a pneumatic chipping hammer has been made. This paper presents a nonlinear computational model of a pneumatic chipping hammer. In order to better understand the dynamics of the chipping hammer, the hammer was subdivided into components that are shown in figure 1 (a) (based on a chipping hammer manufactured by Atlas-Copco). The hammer mainly consisted of a center body, a moving piston and a chisel. Compressed air is used to drive the piston inside of a cylinder and on the downward stroke this piston impacts the chisel to create the hammer effect. The machine has one pneumatic valve and this valve regulates the air supply either to the upper chamber or to the lower chamber. The valve changes according to the relative pressures in the two chambers and the supply pressure. There are also twelve different exhaust ports at two positions along the cylinder labeled upper ports and lower ports. As the piston moves the ports can be closed or open (allowing exhaust). Fundamentally, the computational model was made up of two different sub-models, a fluid model and a structural dynamic model as shown in Figure 3 (a) and (b) respectively. The first sub-model takes into consideration the fluid dynamics of the machine since the hammer is driven by compressed air. Equations for the mass flow rate though bleed orifices (assuming an isentropic process) 1 is used to determine the mass flow into and out of the upper and lower chambers. From this the pressures in the two chambers and consequently the forcing on the piston can be calculated. The second sub-model deals with modeling the structural [ ]

Jan 6, 2006

By M. C. Fuerstenau, R. B. Bhappu

The response of beryl to sulfonate flotation was examined. The dependence of flotation recovery on sulfonate concentration, pH, and the absence or presence of various ions is also demonstrated. The response of quartz and feldspar to sulfonate flotation at various values of pH is given to. show the conditions necessary for selective separation. Finally, beryl was successfully concentrated from a natural ore using a technique devised from experimental observations on systems of pure minerals. With the possible exception of quartz, the flotation characteristics of silicate minerals are rather poorly understood. This is due in part to the com- plexity of the mineral systems themselves and in part to an insufficient amount of flotation data. The complexity of the systems arises from the wide range of chemical composition that the silicate minerals can assume. This is reflected in the variability of such physical properties as hardness and cleavage. Although the chemical composition of silicate minerals can vary considerably, a general grouping can be accomplished conveniently on the basis of the assemblage of SiO4 tetrahedra in all the silicates. That is, it has been shown that six basic groups can be obtained, depending on the arrangement of oxygen sharing between adjacent silicon atoms (or substituted aluminum). When all four oxygen atoms are shared, a framework structure such as quartz or feldspar is obtained. When three oxygens are shared, infinite sheets are obtained as in the micas and clays. When two oxygen atoms of the tetrahedra are shared, infinite chains are obtained, such as those in

Jan 1, 1963

By F. B. Plummer

THE physical properties of oil-producing sands, such as grain size, porosity, and permeability, are becoming more and more important in petroleum production engineering as oil fields are being repressured and rejuvenated. A number of excellent papers have been published recently on all three of these properties. Faucher, Lewis and Barnes1 give a com-plete survey of the work done through 1932 and contribute also much information on sands that they themselves have examined. Muskat and Botset,2 Wykoff, Botset, Muskat and Reed,3 Hurst,4 and Muskat5 have contributed a great deal to the theory and actual measurement of flow of liquids and gases through porous media. Muskat and Botset have measured the permeabilities of different sands with gases and liquids. They find that the radial is always slightly under the linear permeability. However, in most of the previous experiments small samples of the sand were used, and the method of production of fluid or gas through the sands has not been very close to actual oil-field conditions. In addition, so far as the authors are aware, no measurements of linear and radial permeabilities have been made simultaneously under exactly the same conditions. The multiple permeability apparatus described here is a part of the equipment being acquired by this laboratory for thorough investigation of the physical properties of producing sands. It possesses certain advantages for comparative studies of liquid flow. Additional data and descriptions of other instruments will follow in papers to be written later on. The essential features of the permeability apparatus are as follows:

Jan 1, 1934

By Fred Delabbio

There are presently several issues that the mining industry is facing, such as underground air quality, deep mining and green house gas emissions, which could be addressed by the application of alternate energies. Several aspects must be considered by the industry in any drive to introduce new technologies within the context of a producing underground mine. This article presents several operational and support aspects that will evaluate the relevance of alternate energies, with emphasis on hydrogen power systems: operational drivers, commercial supply of technology, site supply system requirements, health and safety, capital and operating costs, mine production, corporate philosophy, and role of government. It is concluded that introduction of alternate energy technology requires a step-wise progression: Applicability to the industry, proof of concept testing, development of generic infrastructure, power systems and regulations, whole system studies and detailed studies of cost and risk versus benefits. The current initiative to apply fuel cells is at the proof of concept stage, entering the generic infrastructure stage.

May 1, 2007

By H. M. Smith

Data from the Bureau of Mines routine method for the analysis of crude petroleum are used to characterize crude oils. Some data are used directly while other data are used to calculate the aromatic) naphthene) and paraffin contents of the distillation fractions and the correlation index of the paraffin-naphthene portion of the fractions. The calculated properties show significant differences in composition between crude oils. The methods of calculation and interpretation of data are explained and illustrated.

Jan 1, 1966

Mining ventures are essentially risky businesses. Explorers and project developers (plus their investors and financiers) attempt to minimise the risks involved or at least manage them. Core considerations are the obvious technical and commercial risks, but the socio-political system and regulatory environment in which the project will operate can be more important. Successful mineral investments in a country depend upon obtaining realistic and reliable technical results in a country that provides certainty, to gain and maintain investor confidence in a project. Brief commentary is provided on the usefulness of professional accreditation and ethics plus other specific reporting codes (eg JORC/VALMIN Codes) in reducing risks by reinforcing high technical competence and reputable individual professional behaviour (particularly in the context of currently perceived high corruption levels in so many countries). These various risk components are reviewed, especially in a global context, to showcase New ZealandÆs current position. Successful projects are those which provide investors with credible and reliable optimal results in less volatile environments because investors/lenders hate uncertainty and surprises even more.

Jan 1, 2005

By Raymond J. Castelli

The paper provides a general overview of the numerous types of earth retaining systems currently available, and organizes these various systems by several classification methods. These classifications can be used as a guide in identifying the appropriate type wall or walls for any specific project application. As a further aid in sorting through the numerous wall alternatives for a specific design or construction project application, the paper suggests a systematic approach for wall selection, and presents helpful charts summarizing the general advantages and disadvantages, and typical limitations for the currently available wall systems.

Jan 1, 2003

By K Firmin

The Mt Tom Price orebody of Hamersley Iron Pty Limited consists of a folded hematite - shale sequence capped by a layer of goethite. Consequently, variations in iron content occur within the ore body, and as the overall grade is below that required to make specification products, selective mining must be carried out. A necessary preliminary to quality control of products based on selective mining is the production of advance data on the tonnages and grades of material to be expected in future mining areas. Bench plans showing zones of different grades and types of material anticipated are prepared from structural geological information. The grades of materials on a bench are essentially governed by the positions and attitudes of the shale bands. Quality control is exercised by blending different grades and types of material in primary crusher feed. Iron grade is the prime grade consideration although sometimes the level of phosphorus content must be considered. Pre-production grades are determined from assay of samples taken from blast hole cuttings. As shales are more friable than hematite, product fines are always lower in iron grade than the lump product. The realisation of contract specification grade is more difficult with fines than with lump, so maintaining the correct fines grade becomes a prime factor in quality control. Control of fines grade is presently effected by aiming for an appropriate feed grade to the primary stockpile. Studies to estimate fines grade directly by qualitatively taking into account material types are in progress. Quality control measures are checked by monitoring the crushing and screening plant output, and taking appropriate compensatory actions in the mine when required. Minor fluctuations in quality of fines can be blended out on stockpiles. The quality control measures described ensure constant quality products, and a good recovery of high grade material from the deposit.

Jan 1, 1971

By Narendra N. Khatri, Michael Deutscher, Jozef F. Zurawski

Five sewer connections were required to divert Combined Sewer Overflow (CSO)from existing outfalls to an old underutilized large diameter brick sewer (the Easterly Interceptor). The connections were part of an on-going CSO control program by the Northeast Ohio Regional Sewer District (NEORSD) in the City of Cleveland, Ohio. Each connection was made by pipejacking and hand-mining a fiberglass-reinforced polymer (FRP) pipe through soft glaciolacustrine clays and silts. Jet grouting was utilized to stabilize the soils and fill the voids surrounding the interceptor prior to making the underground connection. Reinforced concrete liners were constructed inside the aging brick sewer to provide structural stability during ground improvements and connection work. The project also involved micro tunneling two approximately400 foot lengths of FRP pipe through soft ground using a slurry pressure balanced machine.

Jan 1, 2005

Coal Preparation Research at Turkish Coal Enterprises (TKI)

Sep 13, 2010

By Luis Armando Espitia

AISI 410 martensitic stainless steel specimens were low temperature plasma nitrided at 400°C in a mixture of 75%N2:25%H2, during 20 h. Active screen technic was used to avoid any edge effect The nitrided case is composed of expanded martensite (a’N) and e-Fe3N iron nitride, whilst chromium nitride precipitation was avoided. Surface hardness reached 1275 HV0.01. The transverse microhardness profile shows a gentle hardness gradient with a NHT nitrided case depth of 28 µm. Nanoindentation tests were carried out in order to assess the hardness (H), the Young modulus (E), the H/E and H3/E2 ratios and the elastic recovery (We) of both nitrided and non-nitrided specimens. The cavitation erosion mass losses were measured as a function of exposure time. The results showed a decrease of 27 times of the mass loss compared to the non-nitride specimens. Wear rate decreased from 2.56 mg/h for the non-nitrided condition to 0.085 mg/h after nitriding. The increment in the elastic recovery and the higher hardness values are responsible for the greater cavitation erosion resistance exhibited by the expanded martensite. Such results showed that low temperature plasma nitriding and the formation of expanded martensite are effective to increase cavitation erosion resistance of AISI 410 stainless steel.

Jul 31, 2018

By A. L. Sweetser

Experience has shown how difficult it is to obtain information regarding laboratory-tests in connection with the chlorina-tion-process for the extraction of gold from its ores, and I therefore present the following method, somewhat in detail, for the benefit of those who may desire to pursue research work in this field. The ore chosen was a partly-decomposed porphyry, extremely siliceous and comparatively soft, and of an average value per ton of from $25 to $26 in gold and $0.68 in silver. The chemical analysis gave: Fe,O,, 3.35; FeS, 1.5; MnO,, 0.75; ZuCO,, 4; A1,0,, 3.20; H,O, 0.7 ; SiO, and insol., 83.50 per cent. The ore, first crushed to pass a 5-mesh screen, was coned and quartered until a 45-lb. sample was obtained. Samples for assay and analysis, taken from this lot by means of riffles, were crushed to pass a 100-mesh screen. The original sample was divided into 10-lb. lots, of which one was crushed to pass a 10-mesh screen; another through a 12-; the third through a 20-, and the last through a 30-mesh screen. Because of the production of an excessive quantity of fine material it was deemed inexpedient to crush finer than 30-mesh size—a decision the wisdom of which is proved by the data in Table I., showing the increasing ratio of slimes, in proportion as the ore is crushed finer. In order to determine the percentage of fines in the sizes of mesh selected, a weighed sample of ore was taken from each mesh, and a sample from the 10-mesh lot was passed successively through 20-, 40- and 100-mesh screens, and the percentage remaining on each screen determined. This process was repeated with the 12-, 20- and 30-mesh lots, with the results given in Table I.

Jan 1, 1908