Search Documents

By Reynold Q. Shotts

A study was made of the coal resources of an area in Jackson County, Ala., forming a part of the Flat Rock, Henegar, and Stevenson quadrangles. The area studied is a portion of the Plateau coalfield on Sand Mountain and is near the Tennessee Valley Authority's Widows Creek steamplant. Since no detailed geological study of this area had been published, some reconnaissance work was done. The coalbeds and adjacent strata such as sandstones, conglomeratic sandstones, and conglomerates were studied. Available drill logs, together with the areal geology, provided sufficient information to permit correlation of the coalbeds and an estimation of coal reserves. For all categories of reserves, computed on a regional basis, a total of 72,920,000 tons of coal more than 14 inches thick is estimated for the areas studied in Stevenson, Flat Rock, and Henegar quadrangles. Of this tonnage, 40,001,000 tons is estimated to have less than 60 feet of overburden. The total measured coal reserves for the above three quadrangles are 16,359,000 tons, with 12,411,000 tons under less than 60 feet of cover.

Jan 1, 1966

By Nabil F. Ismael

The axial capacity of step tapered bored piles in sand was examined by field tests at one site in Kuwait. Two straight piles, and two step tapered piles were load tested in compression to failure. All four piles were 3 m deep. The straight piles were 0.2 m in diameter. The step tapered piles had a diameter of 0.3 m for the upper segment which extended up to 40% of the pile length changing to 0.2 m diameter for the lower section. The soil profile consists of medium to dense sand with minor cementation and no groundwater was encountered. Both the ultimate bearing capacity and the settlement at working loads were examined. The axial capacity of the step tapered piles was greater, and the settlement at working loads was less, compared with the straight shaft piles. The increase in capacity is mainly attributed to the added side friction along the larger diameter top segment of the shaft.

Jan 1, 2008

By R. G. Gürtunca

The future of the United States (US) mining industry will be affected greatly by recent coal mining disasters. These have resulted in new legislation which will have an impact on mining economic costs as well safety and health of miners. This paper discusses the changes that new legislation and regulations are making to the industry and current research that is producing technologies to make mining safer and will likely impact the future of mining.

Jan 1, 2009

By G. I. Gritsko

In this paper we consider the elements of a distributed information geomechanic monitoring system which is used in computerized mine planning and mining operations control. The automated system is a technical means of geomechanic monitoring, as a complex system of regulated observations, estimation and prediction of geomechanic state of rock mass and workings during underground mining of coal deposits. Geomechanic monitoring at coal mines and the automated system execute data collection, analysis and calculations of geomechanic situation in the panel during planning, development and carrying-out of mining operations for ensuring geotechnical stability of underground mining.

Jan 1, 1996

By A. J. MacRae

Metallurgical furnaces are made up of complex multi-component systems that must function either together or in parallel for safe, and reliable operation. Thermal expansion of single material components experience induced stresses during heating and cooling, which can lead to cracking or failure. Multi component elements and systems can experience significant thermally induced stresses during both steady state and transient temperature conditions. Examples pertaining to temperature effects on refractory, copper cooling blocks, furnace shells, and complete systems will be discussed. The purpose of the paper is to highlight how stresses and strains are developed due to differential thermal expansion.

Jan 1, 2015

By Irwan S. Halim

For tunnels in horizontally bedded rock, geologic factors affect the selection and design of the initial supports, including the rock propensity toward parting along bedding and the resulting high potential for rock slabbing during excavation. To evaluate this ground behavior, numerical analyses and results with Mohr-Coulomb, Hoek-Brown, and Ubiquitous Joint constitutive models were used, using the Upper Rouge CSO tunnel in Detroit, Michigan as an example. The different rock models and other geologic considerations are shown to impact the selection of the tunnel initial support and design. This paper emphasizes the appropriate selection of an analytical model based on the site specific geology to achieve an optimum initial support design.

Jan 1, 2008

Possibilities and Working of the Specific Agglomeration of Fibrous Materials and Residues Plant based fibrous materials are becoming of increasing interest in a multitude of industrial applications. Main advantages are the specific lower energy demand and virtually closed CO2 cycle, excellent mechanical properties based on low density as well as a high level of recyclables. In contrast, processing and handling of such materials is associated with a number of challenges. These challenges are mainly related to specific morphological characteristics in correlation to fibre length and structure (branching and splices). Specific problems in further processing steps including transport, dosage or storage for natural fibre compounding, result from form-locking bonds leading to burling, clusters or plaits. Technologies of fibre processing are well known, but other than textile based technologies they generally result in intermediate goods which do not allow direct industrial application. The investigation to be presented is based on results of recent research activities and shows two possible technical solutions of innovative fibre agglomeration procedures. These methods allow the conversion of middle to long fibres into a form, which eases further processing and dosage significantly and therefore allows free flowing too. The procedures are based on the working principles of rolling and winding technology. Within the work, both of the patented methods and their respected lab-scaled devices will be described. Further, results will be shown for an up-scaled rolling agglomeration unit applying the developed principle and consisting of multiple process zones. Possible variations of the resulting product characteristics and the impact of different process parameters will be discussed based on the trials with natural fibre (hemp and flax) agglomeration. As a main outcome of the research, product qualities can be supplied according to the requirements of the specific application in correlation to agglomerate strength, porosity or form. In conclusion, recent developments for specific methods of characterization will be depicted.

Sep 13, 2010

By M. Rice, M. Stanley, J. Marlow

Arizona construction aggregate industry remains in the crosshairs of public debate, caught between the need for aggregate-based building materials and alternative, high-value land-uses. To better manage lands and improve land-use decisions, the Arizona State Land Department has need for a system to assess potential aggregate resources on State Trust lands, and assign dollar values accordingly. Thereafter aggregate values can be compared to residential, commercial, agricultural, recreational, and habitat values -- in a determination of highest and best land-use.

Jan 1, 2002

By Russell E. Griffin

The current state-of-the-art of fire and smoke detection technology is reviewed from the standpoint of suitability for use in underground metal and nonmetal mines. Detection modes, fire signatures, and environmental considerations are included. Preliminary results of long-term in-mine tests are presented.

Jan 1, 1979

By D. G. C. Robertson

The thermodynamics and kinetics of the reactions involved in fuming zinc from oxide slags using coal or coke were first studied in 1955 and have been the subject of many investigations since that time. The key reaction is ZnO(in slag) + CO = Zn(g) + CO2 This paper will review the some of the recent work, and will add new insights obtained in experiments carried out by the authors. In the first series of experiments it was shown that the reaction does not occur at an appreciable rate, as is expected from thennodynamic considerations. In the second series of experiments it was shown that zinc does not fume from the slag at a significant rate unless a reductant has been added. This again is in accord with thermodynamic considerations, but is in contradiction to some of the experimental results reported in the literature. A third series of experiments was carried out with excess coke being present, so that the rate of supply of reductant was not in any way controlling the rate. The kinetics of zinc oxide reaction were then found to be independent of the zinc oxide concentration, but increased with increasing basicity, and temperature. The presence of high concentrations of FeO in the slag also improves the kinetics. At low zinc oxide coneentrations iron oxide reduction occurred in parallel with zinc oxide reduction. We propose that (under the conditions of this work) the kinetics were controlled by a chemical step, namely the rate of desorption of an adsorbed CO2 species. This is the same mechanism as reported by Belton and co-workers for the kinetics of the reduction of FeO. This explains why the reduction of metal oxides in slags by hydrogen is often faster than by CO.

Jan 1, 2003

By K. H. Hofer

La mecánica de rocas se basa en el descubrimiento de las leyes que siguen las perturbaciones del estado natural de la corteza terrestre provocadas por la actividad minera. En ese sentido, el presente texto señala la importancia de este proceso en la ciencia de la minería -en tanto revisa el comportamiento de la resistencia de la roca, determina el estado de las tensiones primarias de la corteza terrestre y analiza la repartición secundaria de tensiones provocadas por la formación de huecos y sus consecuencias sobre la roca en el espacio y tiempo.

Nov 1, 1971

By W. Lin, H. Endo, M. Kwasniewski, A. Kamei, M. Takahashi

Uniaxial tension tests were conducted on specimens of eleven granitic rocks which came from eastern Japan, and included a granite, four granodiorites, four tonalites and two gabbros. The axial and transversal deformability of these rocks was determined based on strain measurements using wire strain gauges. The experimental test results revealed that deformational properties of the rocks investigated varied depending on their petrographic features. However, the axial strain and the lateral strain characteristics showed a similar trend for all the rocks, i.e. the stress-strain curves were non-linear throughout the whole stress range from the initial point of loading to the point of ultimate failure. Moreover, the tangent Young's modulus and the ratio of the lateral strain to the axial strain decreased monotonously with the increasing of the axial stress. Still, the deformational properties were different for individual rocks in a quantitative sense. In particular, the difference in the lateral strains among different rocks was more distinct than that in the axial strains. For example, the Poisson's ratio at a stress level equal to 50% of the ultimate strength of a granodiorite was very low, close to zero. Furthermore, the Poisson's ratio of a tonalite was lower than that of a granodiorite, and assumed a negative value. This effect occurred because the lateral strain became positive as it changed from contraction at the initial stage of loading to extension at higher stress levels. There is no ready explanation for this phenomenon; it is believed, however, that it occurs due to microcracks pre-existing in rock materials and/or weak bonds between the adjacent mineral grains. Les essais de traction directe ont été conduits sur les échantillons de onze roches granitiques provenant de la région Est du Japon: un granit, quatre granodiorites, quatre tonalites et deux gabbros. Déformabilité axiale et transversale de ces roches s’était déterminée en utilisant des jauges extensométriques à fil. Les résultats obtenus à partir des essais montrent que la déformabilité des roches examinées varie selon leurs propriétés pétrographiques. Cependant, à partir des essais, une tendance semblable était observée dans les paramètres de la déformation axiale et la déformation latérale de toutes les roches; c'est-à-dire chaque courbe de contrainte-déformation était non-linéaire dans tout l'intervalle de contraintes à partir de l’état initial jusqu’à l’état d’une rupture finale au cours du chargement. De plus, le module tangent de Young et le rapport de la déformation latérale sur la déformation axiale a diminué de manière monotone avec l'augmentation de la contrainte axiale. Cependant, les différences quantitatives de propriétés de déformation sous traction étaient observées entre des roches individuelles. Particulièrement, la différence de déformations latérales était plus notable que celle-là de déformations axiales entre des roches différentes. Par exemple, le coéfficient de Poisson à un niveau de contrainte égal à 50 % de la résistance d'un granodiorite était très bas, près du zéro. En outre, le coéfficient de Poisson de la tonalite était inférieur que celui du granodiorite et a assumé une valeur négative. Cet effet est apporté parce que la déformation latérale est devenue positive en passant de la contraction dans l'étape de chargement initiale à l'extension sous les contraines plus hautes. Il n'y a aucune explication prête de ce phénomène; on prétend, cependant, qu'il est induit par des microfissures préexistantes dans des matériaux rocheux et/ou des joints faibles entre les grains minéraux adjacents. Einaxiale Zugversuche wurden auf Probestuecke von elf frischen, in Ostjapan vorkommenden, granitartigen Gesteinen durchgefuehrt, welche einen Granit, vier Granodiorite, vier Tonalite und zwei Gabbros umfassten. Die axiale und transversale Verformbarkeit von diesen Gesteinen wurde durch Verformungsmessungen mit Drahtdehnungsmessstreifen geklaert. Die experimentellen Versuchsergebnisse offenbarten, dass Verformbarkeitseigenschaften des untersuchten Gesteins in Abhaengigkeit von ihren petrographischen Eigenschaften variierten. Jedoch zeigten die axialen und die lateralen Spannungsdehnungslinien eine aehnliche Tendenz bei allen Gesteinen, d.h. die Verformungskurven waren nicht linear im ganzen Bereich vom Ausgangspunkt des Belastens bis zum Punkt des entgueltigen Bruchs. Ausserdem verringerten sich das tangentiale Elastizitaetsmodul und das Verhaeltnis der lateralen Verformung zur axialen Verformung monoton mit der Erhoehung der axialen Spannung. Dennoch waren die Verformbarkeitseigenschaften der einzelnen Gesteine in der quantitativen Wahrnehmung unterschiedlich. Insbesondere war der Unterschied bezueglich der lateralen Verformungen zwischen verschiedenen Gesteinen eindeutiger, als der in den axialen Verformungen. Z.B. war die Querkontraktionszahl auf einem Spannungsniveau, das 50% der Zugfestigkeit eines Granodiorits entspricht, sehr niedrig und nah an Null. Ausserdem war die Querkontraktionszahl eines Tonalits negativ und deshalb niedriger als die eines Granodiorits. Dieser Effekt trat auf, weil die laterale Verformung, als sie sich von der Kontraktion am Ausgangsstadium des Belastens bis hin zur Ausdehnung auf den hoeheren Spannungsniveaus aenderte, positiv wurde. Es gibt keine fertige Erklaerung fuer dieses Phaenomen; es wird jedoch angenommen, dass es wegen der Mikrorisse auftritt, die vorher im Gesteinsmaterial und/oder in den schwachen Bindungen zwischen den angrenzenden Mineralkoernern existieren.

Jan 1, 2003

By Z. Henderson, J. Saylor, L. R. Mendoza

"Diesel particulate Matter (DPM) is a byproduct of fuel combustion in diesel engines. It is classified as a carcinogen, with associated respiratory and cardiovascular health effects. The composition, size, and concentration of DPM is dependent on factors such as engine type, loading and fuel composition. Though a number of DPM abatement and control strategies currently exist, particularly in underground mining environments, occupational exposures remain a serious health concern. As a novel abatement approach, DPM scavenging by fine water or “fog” droplets has been proposed and a laboratory set-up has been built to test the efficacy on engine exhaust. Here, we describe a series of tests that varied engine load, system flow rate and fog drop number density. While none of these factors had overwhelming effects on the results within the ranges tested, the improvement in DPM mass removal attributed to the fog treatment was about 45% on average in comparison to no treatment. INTRODUCTION Diesel engines have seen widespread use for well over a century due to their relatively high thermal efficiency and fuel economy1. More recently, however, adverse health risks of diesel exhaust have become increasingly clear. Many of these risks are associated with the physical and chemical properties of exhaust components1–3. The term diesel particulate matter (DPM) is used to refer to the solid components of diesel exhaust, which are a mixture of elemental and organic carbon (EC and OC) and minor constituents including sulfates and metal ash3. The OC fraction of DPM results from unburned fuel and lube oil, whereas EC or soot is formed during the combustion of locally rich regions within the fuel. DPM is classified as a carcinogen6,7 and epidemiological studies have demonstrated a positive correlation between long-term exposure to DPM and other combustion-related fine particulate and increased cardiovascular and pulmonary diseases8,9. Diesel engines operate in relative fuel rich/oxygen lean conditions and are characterized by relatively high emissions of particulate as compared to spark-ignition engines2,3,10. Typically, these emissions range from 107 – 109 particles/cc and cover two primary size ranges: the nuclei mode where particles have diameters less than about <50 nm, and the accumulation mode where diameters are from about 50-10,000 nm. Most OC resides in the nuclei mode as semi-volatile compounds, while most EC is in the accumulation mode3. The physical and chemical properties of DPM vary with the type of engine, fuel (e.g., petro- vs. bio-diesel) and operating conditions such as loading (i.e., a function of torque and rotational speed)2,3,9,11,12. Loading is a particularly important factor with respect to DPM toxicity9,13,14, and on the effectiveness of after-treatment technologies2,3,15. Engine load alone can affect the EC/OC ratio, and the size distribution and number density of DPM. For diesel engines, the load is roughly proportional to the equivalence ratio3, defined as the actual fuel/air ratio over the stoichiometric fuel/air ratio for complete combustion. Light loads generally favor the formation of OC and small particles. As load is increased the volatiles are oxidized leading to larger soot particles (i.e., EC), but lower total number density of DPM. With further loading, the formation of soot offsets the decrease in volatiles, resulting in increased DPM mean size and number density3."

Jan 1, 2017

Mine drainage and mine reclamation are topics of major interest to the mining industry, federal and local governments, and the general public. This publication and its companion three volumes are the proceedings of a conference held in Pittsburgh, Pennsylvania, April 24-29, 1994. There were twelve sessions (69 papers) that dealt with mine drainage, including modeling, geochemistry, prediction, treatment, control strategies, characterization, hydrology, and case studies. These sessions comprise volumes 1 and 2. The six sessions (34 papers) that dealt with reclamation and revegetation of disturbed lands are included in volume 3. Volume 4 includes the six sessions (34 papers) that dealt with such topical issues as fires at abandoned mine sites, subsidence, hydrology, mine wastes, and policy. Poster session presentations are represented by 49 papers and 92 abstracts that have been placed in the back of volumes 2, 3, and 4, consistent with the subject of that volume.

Jan 1, 1994

By T. L. Johnston

MUCH has been said and written about deep mine shafts and deep drill holes as man in his search for mineral wealth digs deeper into the earth&apos;s crust. Each year some new extra depth is heralded as a record, but with unlimited possibilities of going still deeper. In contrast to "digging deep," "mining high" is limited by the height of the mountains (Mt. Everest being the maximum with its 29,000-ft. elevation) and also by the extent of human endurance. An ex- ample of what might be called near- stratosphere mining in what is probably the highest mine worked by compressed air in the world is seen in a recent project in the Andes mountains of southwestern Bolivia.

Jan 1, 1939

By Charlie Adcock, Rob Farnfield, Andy Wetherelt

The ISEE Blasters Handbook gives guidance on the level of air overpressure likely to cause occasional window breakage (151dB) and general window breakage (171dB). A long-term safe level of 140dB is also suggested. This guidance is widely used by demolition and other contractors to assess damage zones in the region of explosive applications employing unconfined charges. Other reference material gives more detailed guidance relating to window area, aspect ratio and glass thickness. Despite the guidance given in these references, complaints by members of the public regarding window breakage continue to be received by explosives engineers from air overpressure levels well below the longterm safe limit. Such complaints are not limited to the use of unconfined charges but can even be generated from the highly confined use of explosives in quarry blasting. This paper describes a series of experiments with explosive charges fired in unconfined conditions close to various window configurations. The aim of the work was to test the existing guidance levels and to extend the knowledge base in this area. Topics covered include the role of differential pressure across windows in the walls of an enclosed space such as a room.

Jan 1, 2006

By J. W. Walkiewicz

The Bureau of Mines investigated alloys containing lanthanum (La), praseodymium (Pr), neodymium (Nd), cobalt (Co), copper (Cu), iron (Fe), and magnesium (4g) as possible components of a permanent magnet mate¬rial utilizing a cerium-free synthetic mischmetal (M) as a substitute for scarce samarium (Sm) metal. Magnets containing M-Co-Cu-Mg and M-Co-Cu-Fe-Mg were fabricated by powder metallurgy techniques and evaluated. A synthetic mischmetal (M20) containing 20 pct La, 60 Pr, and 20 Nd yielded the best overall magnetic properties. The M20-Co-Cu-Mg alloys had energy products as high as 13.2 MGOe, remanences as high as 7.89 kG, normal coercivities as high as 6.26 kOe, and intrinsic coercivities as high as 13.4 kOe. The best value of intrinsic coercivity, 22.9 kOe, was obtained with an M-Co-Cu-Mg magnet in which the synthetic misch¬metal contained 30 pct La, 50 Pr, and 20 Nd. These values compare favorably with those of the Sm-Co magnets fabricated and measured at the Bureau&apos;s Reno Research Center, which had energy product of 15.1 MGOe, remanence of 7.8 kG, normal coercivity of 7.5 kOe, and intrinsic coercivity of 27.4 kOe. Iron substitution for part of the cobalt resulted in a decrease of magnetic properties, although several percent iron can be added before a drastic loss of magnetic properties occurs.

Jan 1, 1983

By J. Kern, T. F. Torries

Identifying high value areas of unmined coal when large quantities of coal are available relative to annual markets is difficult because of the uncertainty of when the coal is to be mined. A GIS based methodology developed to value reserve coal in a producing coal region for the purpose of ad valorem taxation also identifies high value areas for mining investment. The methodology is unique in that it accounts for most mining, environmental, and market factors to determine when specific properties are to be mined. The methodology and data base are useful for directing regional exploration and acquisition activities toward most favorable areas.

Jan 1, 1999

By E. F. Schnitzer, S. R. Mamoyac, P. J. Wampler

During 1996 and 1997, Oregon experienced flooding on a scale not seen in many years. Some gravel pits located near rivers experienced erosion and, in several cases, breaches between the gravel pit and the river. Initial evaluation of several sites that experienced breaches indicates that impacts to the river system are complex and vary significantly from site to site. The impacts to the adjacent river system may be viewed as both positive and negative. Several floodplain-mining sites in Oregon located in areas of historic river flow have reverted to active riverbed. In many cases, state and federal fisheries biologists and university researchers see the resulting increase in channel complexity and habitat as favorable. The Oregon Department of Geology and Mineral Industries – Mined Land Reclamation Program (DOGAMI-MLR) is performing additional studies of the impacts to the off-channel areas that resulted from the 1996 floods. More data is needed to make sound floodplain decisions regarding mining.

Jan 1, 1999

By A. J. Williams, T. N. Croft, M. Cross

"The computational modelling of extrusion and forging processes is now well established. In this work a novel approach is described which utilises finite volume methods on unstructured meshes. This technique can be used to solve simultaneously for fluid flow, heat transfer and non-linear solid mechanics and their interactions. The approach involves the solution of free surface non-Newtonian fluid flow equations in an Eulerian context to track the behaviour of the workpiece and its extrusion/forging, and the solution of the solid mechanics equations in the Lagrangian context to predict the deformation/stress behaviour of the die. Some preliminary examples of this approach will be discussed.IntroductionThe computational modelling of extrusion and forging processes is now well established. Within the last 20 years the finite element method has become the most commonly used technique to simulate metal forming processes [1]-[4]. The Lagrangian and Eulerian type of formulation have been the two major approaches to this problem.Lagrangian methods are efficient and suitable for handling non-linear problems in which small strains prevail, boundary conditions do not change with the course of deformation, and where mesh distortion is not a critical factor in the analysis. Unfortunately, the above points are essential to any accurate metal forming analysis. The problems of mesh distortion and element entanglement pose a serious drawback on the use of such methods. Some automatic remeshing techniques have been developed for Lagrangian finite element analyses of metal forming problems [5]-[7]. However, these methods are not robust and efficient enough to remedy the mesh distortion problems in general. An alternative is to update the mesh manually but this is not always possible, and even when it is feasible it involves major interaction by the user. In addition, remeshing is usually applied to the whole domain which is not necessary and increases CPU time. The complexities associated with remeshing also affect the ability to parallelise the code."

Jan 1, 2001