Search Documents

By g. Caproni

The main constituent of the feed to the "Sulphide Section" (31 t/h), in the F. Sartori Plant (6000 tid) of the Miniere di Mon)eponi(Sardinia), is the ore of the Campo Pisano -Funtanaperda Mine (1 ? Difficulties have always been experienced in the treatment of this ore, owing to the extramely fine Pyrite-Sphalerite intergrowth and to the high Pyrite and soluble salts contents. The first mentioned difficulty was overcome with a rather complex flowsheet (see fig.1A and lB)(2); the others with a reagent combination that required a pH of 11 in a pulp loaded with soluble salts. This meant high consumption of alkalizer, and also of the other reagents; furthermore the alkalizer had to be mainly NaOH with only minor amounts of lime, because the latter tended to depress not only the pyrite but also the middlings, which were supposed to float. With dialchylditiophosphate alone as a collector, a lower pH could have been used, but a certain amount of amylxanthate was indispensable to promote flotation of the middlings. On the other hand, a bulk-flotation of sphalerite and pyrite at low pH could not be very advantageous on account of the high pyrite content in the feed(3).

Jan 1, 1971

By D. D. Tannant

An experimental and numerical study was conducted on the geomechanical behaviour of oil sands during penetration tests in which a steel wedge with an apex angle of either 20 degrees or 30 degrees was forced into compacted oil sands. The boundary conditions simulated in the laboratory tests are similar to shovel penetration into oil sands. The objective of the laboratory tests was to measure the force required to push a steel wedge into compacted oil sands. A wedge penetration test differs from conventional triaxial tests in that much more shear is generated. The laboratory data was needed to improve calibration of micro-mechanical input parameters for a two-dimensional discrete element model of oil sands constructed with Particle Flow Code (PFC). Initial model calibration was performed with triaxial test data and then a PFC model of the wedge penetration test was constructed. The measured force-displacement behaviour of the steel wedge was compared with PFC modelling results. It was found that different combinations of PFC particle and bond parameters could equally well replicate the laboratory triaxial compression data for bitumen-rich oil sands. When the wedge model was run, it was found that the resulting force required to penetrate the wedge into the oil sands was about four to six times higher than that measured. This clearly indicates that further research is required to improve the predictive capability of PFC models of oil sands.

Jan 1, 2002

By B. S. Terry

Experiments have been conducted to assess the feasibility of capturing bearing emissions arsenic with CaO during the roasting of enargite (Cu3AsS4). Enargite/CaO mixtures have been heat treated in air, nitrogen or oxygen for various times and the products of reaction analysed by X-ray diffraction and cleaned analysis. The results show that substantial capture of arsenic can be achieved via the formation of calcium arsenates and/or calcium arsenides. In addition significant capture of sulphur is achieved by the formation of calcium sulphate andlor sulphide. Complete conversion to copper sulphide with total removal of arsenic can be achieved within 30 minutes at 700°C. Further heat treatment in air or oxygen leads to the formation of copper oxide and copper oxysulphate. Without optimisation of reaction conditions, it has proved possible to achieve retention of in excess of 85% of the arsenic content of enargite in the form of calcium arsenates.

Jan 1, 1994

By Carlos A. Barrena Chávez

El presente trabajo señala una variación en la preparación del Under Cut como método de Explotación Sub Level Stopping 3 en la mina Iván -en tanto es usado como subnivel para el reconocimiento, perforación radial y ventana de extracción durante el proceso productivo. El desarrollo de este método contempla una rampa principal de acceso, desde donde se realiza el trabajo de preparación de la cámara para su posterior explotación.De otro lado, se resalta la importancia del estudio geomecánico para el dimensionamiento de la cámara y la secuencia de explotación en el planeamiento de minado.

Sep 12, 2005

By A. Zhecheva

A commercial titanium alloy Ti-6Al-2Sn-4Zr-2Mo has been gas nitrided in this work, in pure nitrogen atmosphere in order to improve its surface properties. The nitriding was performed at two different temperatures, 950 and 1050°C, and for different periods of time. The influence of the initial surface roughness on the diffusion process and on the surface properties of this material was studied. The influence of the processing parameters of gas nitriding on the surface roughness, phase modifications and the microstructure of the nitrided layers has been analyzed using atomic force microscopy (AFM), X-ray diffraction and optical microscopy. Microhardness profiles were obtained on cross-sections of the samples after gas nitriding applying a Knoop indenter.

Jan 1, 2004

By P Knights

This paper examines the process and specialised skills required to extract insight from data routinely collected by mine operations, maintenance, engineering and environmental departments. Typical insights include: enhanced understanding of root causes; recommendations for next best actions; and simulation of likely scenarios. The skills required for advanced analytics are not currently the domain of mining engineers. The professions required by tomorrow’s mines are likely to be diverse and multi-disciplinary, and will include control engineers, software engineers, mathematicians and statisticians. A case study is presented that correlates mobile equipment production delays with rainfall events across three mines on the east coast of Australia. One mine is shown to have significantly more rain related downtime than the other mines, providing compelling evidence to improve productive performance.

Nov 22, 2011

By A. S. Malicsi, R. J. Lipp, I. Iwasaki

A loch-grade copper-nickel deposit, with an estimated 4.6 Gt (5 billion st) and average analyses of 0.6% copper, 0.2% nickel, occurs in northeastern Minnesota. In addition to copper, nickel, cobalt, and precious metals, the Duluth gabbro contains magnetite, ilmenite, olivine, plagioclase, and biotite. It u estimated that flotation tailings that would be produced by a concentrator of optimal size to sustain a smelter would amount to 20 Mt/a (22 million stpy). The flotation tailings, having already been ground, warrant a closer examination for recovery and use of potential byproducts. Residual sulfide minerals and fibrous minerals may also be isolated and treated separately for useful purposes or for disposal in an environmentally acceptable manner. Two flowsheets were developed; one involving preconcentration by low- and high-intensity magnetic separation and another involving preconcentration by gravity concentration. Concentration methods for recovering and purifying individual byproduct minerals were investigated. From their chemical, physical, and mineralogical characteristics, the potential areas of application and marketabilities of each product fraction were surveyed.

Jan 1, 1985

By W. H. Herschel, E. W. Dean

"IntroductoryThe common practice of the petroleum industry is to measure viscosity by the use of instruments of the efflux or capillary tube type. The Saybolt universal viscosimeter has been tentatively adopted as a standard by the American Society for Testing Materials and is used extensively in the United States.Several instruments of foreign origin are also more or less familiar, such as the Redwood, the Engier, and the Baroey.Effina-type viscosimeters are well adapted to the ordinary needs of petroleum testing laberatories as they are simple and rugged in construction and away to manipulate, even in the hands of operators lacking scientific training. They have, however, certain limitations and for certain spacial types of work there are notable advantages incident to the use of the so-called torsion types of type of viacosimeter. The most satisfactory type of torsion viscosimeter now available in the market some to be that of MacMchael, which has been discussed in detail in a recent paper (Herschel, W. H., The MacMichael Torsional Viscosimeter. Jour. of Int. and Eng. Chem., vol. 12, 1920, pp. 282-286). The present paper indicates conditions under which this viscosimeter may be used to advantage in the petroleum laboratory, and outlines simple methods of operation and calibration."

Jan 1, 1921

By R. M. S. Häggblad

The article deals with stabilisation and regeneration of Ce02 and Ce02/Zr02 based Pt water gas shift catalysts, subject to high initial deactivation. The reaction gas species effect on the catalyst deactivation was investigated by H2-TPR. Activity measurements enabled the effect of different promoters, some added to the Ce02 based catalysts and some to the Ce02/Zr02 based Pt catalysts, to be investigated. The catalysts were also characterised by BET and CO-TPR. Deactivated catalysts activity was restored by using various regeneration methods. Of the two selected carriers the Ce02/Zr02 based Pt catalyst showed the highest resilience to deactivation. For the two different carriers, Ce02 and Ce02/Zr02, Wand Re were the best promoters when the catalyst was subject to deactivation. Experiments with Hr TPR indicate a fast initial change in the platinum oxides concentration and composition. The CO-TPR was used to make conclusions about the various regeneration effects of water and oxygen on the catalyst. Finally it is suggested that not one deactivation mechanism is possible and which mechanism that dominates is dependant on the catalyst and the reaction gas composition.

Jan 1, 2005

By Richard Chojnacki

The western united States is not usually noted for the production of fluorspar; however, many significant fluorspar districts do occur in the Rocky Mountain region and constitute a resource of sizable dimension and major potential. This is particularly true within the area of the West served by the rail lines of the Union Pacific Railroad (see Figure 1). Fluorspar deposits near the Union Pacific have produced over 1.3 million tons of finished fluorspar products from 2.3 million tons of ore. Approximately 80% of this production was of acid-grade and 20% of metallurgical-grade fluorspar. Production of ceramic-grade was negligible. Through the years substantial production has come from eight mining districts. Five of these have produced metallurgical-grade and three acid-grade. The best-known fluorspar producing area in the West is the Jamestown Mining District. It was one of the first producers of fluorspar in the western United States and is estimated to have produced over 500,000 tons of finished fluorspar from over a million tons of ore. The district encompasses approximately 36 square miles in central Boulder County, Colorado, about 9 miles northwest of the City of Boulder. Although small shipments were made from the district as early as 1873 or 1874, significant sustained production was not achieved until 1940 when the General Chemical Company, now a division of the Allied Chemical company, acquired the Alice, Burlington, Chancellor,

Jan 1, 1971

By D. Harrington

Near the close of the nineteenth century electricity was introduced underground, and the mining industry automatically was confronted with another potential source of fatalities and injuries to mine workers. Electricity has become an increasingly vital factor in the production of goal, particularly in recent years, because of the greatly extended mechanization that has taken place underground. The enlarged use of electrical equipment for cutting, loading, and hauling coal unquestionably increased the potentiality of shock and explosion hazards underground. Electricity may be used in coal mines with minimum danger if electric equipment and power-carrying wires are chosen properly and installed and kept protected by proper safeguards; on the other hand, if vigilance is relaxed in the slightest degree accidents may result. Electrical accidents are caused chiefly by direct contact with electrical equipment or power-carrying wires, by ignition of explosive gas or dust, and by fires of electrical origin. Electricity now ranks fourth as a cause of coal-mine fatalities, not including deaths from explosions or fires of electrical origin.

Jan 1, 1936

By James Paone

Drillability of rocks by mechanical means is closely related to the physical properties of the respective rocks, Various approaches by previous investigators on rock drillability are presented, as well as recent techniques studied by the Bureau of Mines. The studies show drillability concepts based on (1) theoretical drilling equations derived from laboratory drilling experiments extended to field drilling results and on (2) a statistical method where multiple regression analysis is used to develop a prediction equation for drillability.

Jan 1, 1966

By Irene Bendanillo, Canon Cheung, Justin Lianides, Derek Penrice

The SLAC National Accelerator Laboratory’s two-mile-long particle accelerator generates the world’s brightest X-rays from its Linac Coherent Light Source (LCLS) freeelectron laser. This facility has driven groundbreaking discoveries in medicine and industry. The LCLS-II-HE project will provide a significant increase in laser energy, allowing cutting-edge research in fields including biology and environmental science. A key project component is the Low Emittance Injector Tunnel (LEIT), a 240-foot-long tunnel to be built alongside the existing accelerator and connected to it via a 30-footlong Transfer Tunnel. This paper discusses site and scientific constraints that led to the selection of the LEIT configuration: tunnels to be constructed using the sequential excavation method in mixed-face conditions comprising native rock and placed backfill, and critical design considerations including protection of overlying and adjacent historic structures and structural accommodation of near-fault seismic loading.

Jun 13, 2023

By Yoginder P. Chugh

Most mines are large producing 0-25 mmt annually. The coal is mine.) at depths ranging from .0-150 m 120-500 ft mining at 300 m .(,1000 ft) depth is anticipated in the future. Single and multiple seams ranging from 3-12 m 10-40 ft) in thickness are mined. Most overburden is unconsolidated and consists of sands, and sandy or silty clays. The stripping ratio (volume of overburden to volume of coal mined) varies from 3-L. The overburden and coal is mined in benches 8-12 m -(24-40ft) high; the high-wall angle is about 45 degrees. Bucket wheel and bucket chain excavators are commonly utilized for overburden and coal removal, Some of the large overburden stripping machines nave capacities. Ranging from 4400-10,000 bank cu ( 6000-14,000 BC) per hour. The overburden from the upper benches is transported around the pit using the trains and belt conveyors. It is deposited in the spoils using large stacker-conveyor systems capable of handling 2550-7300 cu m/hour (7500-10,000 cu yds/hour). The overburden from the bottom two or three benches is transported across the pit using the conveyor bridges which are computer controlled. Conveyor bridges capable of handling overburden up to 60 m (200 ft) high are currently in use; a 60 a (20e ft) high conveyor bridge has a capacity of 85 x 10 cu ( 118 x 10 cu yd) annually. The coal is loaded in the trains directly and shipped to power plants or coke oven plants.

Jan 1, 1980

By F. K. McKean

Introduction The present paper may be considered as a sequel to a paper, A Process for Cleaning Molybdenite .Concentrate, which was presented by the author at the annual meeting of the Institute last year. In that paper, a description was given of the laboratory work leading up to the adoption of a new process for treating complex molybdenite ores of the Molybdenite Corporation of Canada. A bare outline of mill performance with the new flow-sheet was included. With this writing, the purpose is to describe the highly interesting work of translating laboratory experience into mill practice, to show what changes were required in design to put the scheme on an operational basis, and to point out the gratifying improvements in mill products which resulted from the new procedure. The process has been placed in operation at the La Corne mine of the Molybdenite Corporation of Canada. This mine was operated during the war by Wartime Metals Corporation, and, earlier, by the Molybdenite Reduction Company, which installed a small plant. The property is situated on the highway from Amos to Val d'Or, Quebec. The claims held by the Company are at the boundary between La Corne and Vassan townships.

Jan 1, 1947

Study on Oil Agglomeration Flotation for Deinking

Sep 13, 2010

By Walter Valery

Dado que el mercado de metales se hace cada vez más competitivo, se busca implementar nuevas tecnologías y metodologías más eficientes que aseguren la rentabilidad de la operación minera largo plazo. En ese sentido, el presente texto describe el procedimiento para iniciar e implementar el programa Metso Process Technology & Innovation (PTI) como parte de la metalurgia. Para ello, se describen los datos requeridos y la forma cómo deben ser evaluados e incorporados a los modelos GeoMetso. Así el programa surge como una alternativa costo-efectiva para ejecutar modelos geometalúrgicos de mayor precisión, de forma que se optimizen los resultados para las operaciones a lo largo del periodo de vida de la mina.

Mar 1, 2016

By Denis Racicot

"L'Abitibi québécois a produit essentiellement de l’or, du cuivre, du zinc et de I' argent, ainsi que de faibles quantités de nickel, de plomb, de molybdène, de bismuth, de lithium, de fer et d’amiante. Depuis l’ouverture de la mine Horne en 1927, cent-cinquante mines ont contribué à la production de 1 420 tonnes d’or de 4,1 millions de tonnes de cuivre et de 4,7 millions de tonnes de zinc. Les productions minières annuelles ont été d'importance variable: des records de production ont été établis en 1955 pour I' or avec 35 tonnes et, vers 1965, pour le cuivre, le zinc et la quantile globale de minerai extrait avec respectivement 130,000, 275 000 et 13 millions de tonnes. Deux dépressions généralisées ont eu lieu, l’une vers 1946 et l'autre, a lafin des années soixante-dix. Des ralentissements de la production ont été observes pour le cuivre en 1953 et le zinc en 1959. Depuis le debut des années quatre-vingt. I' or et, de façon plus irreguliere, le zinc sont en progression, landis que le cuivre, malgre une hausse en 1983. pour suit son dec/in.La teneur de récupération des mines d’or est demeurée régulière et n’a subi qu’une faible diminution au cours des quarante dernières années. Célie du cuivre a diminué d'environ 50% dans la même période, landis que celle du zinc a subi d’import antes variations, aussi bien positives que négatives. Près des trois quarts des mines d'or ont une durée de vie inférieure à 12 ans et la distribution des tonnages de minerai extrait montre un maximum pour la classe de 100 000 à 1 million de tonnes. Du cote des mines de métaux de base, la durée de vie est plus étalée et les volumes de minerai ont une occurrence maximale dans la classe de 1 à 10 millions de tonnes.Concernant la distribution géographique de la production minière dans l'Abitibi québécois, le camp minier de Rouyn-Noranda vient en tête pour l’extraction de minerai et la production d’or et de cuivre. L’est sui vi par le camp de Val d'Or pour le minerai et l’or, landis que le camp de Chapais-Chibougamau occupe la deuxième place pour le cuivre avec une production équivalence a 60% de celle de Rouyn-Noranda. Le camp de Cadillac-Malartic suit de tres pres celui de Val d'Or pour ce qui est de I' or. Finalement, dans le casdu zinc, le camp minier de Joutel-Matagami domine largement avec une production qui a connu un développement accélère depuis 1963. Une analyse pré liminaire de ces données indique qu' i/ subsiste unpotentiel encore élevé de production d'or, décuivre et de zinc dans I' Abitibi québécois. ABSTRACTThe Quebec portion of the Abitibi belt has essentially produced gold, copper, zinc and silver, as well as some small quantities of nickel, lead, molybdenum, bismuth, lithium, iron and asbestos. Since the opening of the Horne mine in 1927, one hundred and fifty mines have produced 1420 tons of gold, 4,1 millions tons of copper and4,7 millions tons of zinc. Annual mine production has fluctuated: production records were established in 1955 for gold with 35 tons, and around 1965 for all extracted ore copper and zinc with respectively 13 millions, 130 000 and 275 000 tons. Two main recessions have occurred, the first around 1946 and the second during the late seventies. Cut backs in copper and zinc production occurred in 1953 and1959. Since the beginning of the eighties, gold production and to a lesser extent zinc production have been in progression. Except for a small jump in 1983, copper production is still declining.The average recuperation grade of gold mines has been quite steady and has only slightly diminished in the past forty years. The average copper recuperation grade was halved during the same time interval. For zinc there have been important ups and downs. At least three quarters of gold mines have an average lifespan of 12 years the tonnage distribution shows a peak in the 100 000 to 1 million tons class. Base metals mines show a more widespread life expectancy and have a tonnage peak in the 1 to 10 millions tons range"

Jan 1, 1990

By Y. C. Kim, I. S. Roditis, P. K. Medhi

P. Mousset-Jones I found the article most interesting and timely. I consider it imperative that mine case studies like this one are undertaken and published so that the practicing mining engineer and geologist can obtain a better idea of what is the preferred estimation and grade control technique to use, given the site-specific geology, grade distribution, etc. Mining companies, with operating gold mines, need to be encouraged to either initiate such a study in-house or support a research project by financing a graduate student at a local university. The latter method is preferable since it not only provides research support but also an excellent training opportunity for young mining engineers and geologists. Ideally, what is needed is exploration drill-hole, blasthole, and mine production data that can then be used to assess the efficiency of different estimation and grade control methods by comparing the results obtained using the drill/blasthole data with the actual production data. It is hoped that more mining companies will realize that the rewards from this kind of research greatly outweigh the sometimes perceived problem with releasing data to a university. I noticed that the authors used the blasthole data to represent the actual values, the validity of which relies heavily on the two key assumptions with regards to blasthole assays and in-pit ore-waste selection procedures. Could the authors comment in more detail on these assumptions and what criteria they used to check the validity of the assumptions? Since the article was published, have the authors had the opportunity to compare their estimates with the actual production data? It would be interesting to compare other estimation methods with OK and IK. For example, how well did the polygonal method used at the mine compare with the results given in the paper? I would like to mention that B.L. Kwa completed a similar study (Kwa and Mousset-Jones, 1986) using exploration drill-hole, blasthole, and production data from the Alligator Ridge mine in Nevada. The study compared a variety of estimation methods, including IK, and the final results are shown in Fig. 1. The IK method exhibits the smallest difference between estimated and production results and is closely followed by the indicator moving window (Ind MW) method. Reference Kwa, B.L., and Mousset-Jones, P., 1986, "Indicator Kriging Applied to a Gold Deposit in Nevada," Proceedings, Symposium on Ore Reserve Estimation Methods, Models, and Reality, CIMM Annual Meeting, Montreal, Quebec, Canada, May, pp. 185194. Reply by Y.C. Kim We do concur with Professor Mousset-Jones with respect to the merit of such case studies performed at a local university. In answer to his request for comment on the validity of the two key assumptions made in our paper, we can only say that these are reasonable assumptions that are very difficult to validate. The assumption of blasthole assays being accurate can be partially validated by a careful analysis of the nugget component of blasthole variograms. The assumption that the in-pit ore-waste selection procedure in use was an effective one can only be validated through comparison between the mine estimates of ounces of gold versus the actual recovered ounces of gold at the mill. Neither one of these two assumptions has been validated to date due to several reasons. For example, the mine went through a change in management since the study. Similarly, no compelling reasons have been presented to perform detailed variogram analysis of the blasthole data. We do, however, believe that the obtained results (i.e., indicator kriging performs better than OK in a highly skewed deposit) will remain the same in relative terms, regardless of how valid these two assumptions may be. The most recent comparative study by D. S. Lindsey of the Montana College of Mineral Science and Technology also shows a similar ranking between ordinary kriging versus probability kriging, which is an extended version of indicator kriging. Reference Lindsey, D.S., 1987, "A Comparative Study: Probability Kriging vs. Ordinary Kriging at the Golden Sunlight Mine," MS Thesis, Department of Mining Engineering, Montana College of Mineral Science and Technology, Butte, MT, May, 81 pp.

Jan 3, 1988

By Donovan J. Benton

Photogrammetric methods are advancing rapidly and show considerable promise as a ground control research tool. The ability to quickly capture three-dimensional geometry, especially changes in geometry, in underground and laboratory settings is a significant advance from point distance measurements. Photogrammetry is being applied in both of these settings as part of the NIOSH ground control research. This paper describes these applications and the equipment and software being employed. It also describes tests conducted to quantify the accuracy of these systems. Accuracy varied with system specifics and procedures. A factory-calibrated camera produced results within 1/32 of an inch, plus 0.04%. A user-calibrated camera was found to be less accurate, at 1/20 of an inch, plus 0.24%. These calibrations demonstrate that photo grammetry can produce research quality measurements in laboratory and mine settings.

Jan 1, 2014