Search Documents

By H. E. Gross

A plausrsle method of drilling beyond the continental shelves is set forth with limitations of the method. The continental shelves comprise the water-covered portions of land masses out to 600 ft. of water, or roo fathoms. The problems and possibilities of drilling beyond this depth are discussed in this paper. Introduction Much attention is being given the problem of developing petroleum beneath the open sea. Geophysical surveys have been made 26 miles offshore1 from the continental United States, and onco offshore ownership is established it is likely that there will be drilling for oil on the continental shelves. More than two years ago the author presented the means for drilling in deep water.2 at the fall meeting of the Petroleum Division of the AIME at Los Angeles. His concepts then were based on the use of rigid foundations suitable for drilling in water up to 600 ft. deep. The present paper suggests a method for drilling in deeper water. Possibilities and Problems of Drilling beyond the continental shelves It being conceded that because restricted deep-water portions of the hydrosphere might contain oil in commercial quantities, and that at any rate it is pertinent to know more of the nature of the lithosphere beneath the hydrosphere, the possibilities and problems of drilling beyond the continental shelves should be set forth. Drilling in open water would offer few if any advantages over drilling on land. These are: 1. The ocean transportation is available to deep-water drilling sites, and extensive pipe lines and roads are unnecessary. 2. Refinery facilities and markets perhaps are established on the near-by shore where adjacent fields on land are nearing depletion. 3. There is freedom from jungle pests and tropical diseases. 4. Competitive drilling is less likely. 5. Extensive areas attractive for development arc not yet under lease or concession. Disadvantages are great and numerous: 1. Storm hazards from wind and wave. 2. Expensive foundations, either rigid or floating. 3. Shutdown times because of weather. 4. Marine Regulations of Federal Bureaus in addition to customary regulations on land. 5. Frequent difficulty in moving men and materials to and from drilling platforms. 6. Extra precautions required in open sea. For drilling in water more than 500 or 600 ft. deep, rigid foundations2 become too costly, and floating foundations must be used, and they must meet the following requirements:

Jan 1, 1947

By H. E. Gross

A plausrsle method of drilling beyond the continental shelves is set forth with limitations of the method. The continental shelves comprise the water-covered portions of land masses out to 600 ft. of water, or roo fathoms. The problems and possibilities of drilling beyond this depth are discussed in this paper. Introduction Much attention is being given the problem of developing petroleum beneath the open sea. Geophysical surveys have been made 26 miles offshore1 from the continental United States, and onco offshore ownership is established it is likely that there will be drilling for oil on the continental shelves. More than two years ago the author presented the means for drilling in deep water.2 at the fall meeting of the Petroleum Division of the AIME at Los Angeles. His concepts then were based on the use of rigid foundations suitable for drilling in water up to 600 ft. deep. The present paper suggests a method for drilling in deeper water. Possibilities and Problems of Drilling beyond the continental shelves It being conceded that because restricted deep-water portions of the hydrosphere might contain oil in commercial quantities, and that at any rate it is pertinent to know more of the nature of the lithosphere beneath the hydrosphere, the possibilities and problems of drilling beyond the continental shelves should be set forth. Drilling in open water would offer few if any advantages over drilling on land. These are: 1. The ocean transportation is available to deep-water drilling sites, and extensive pipe lines and roads are unnecessary. 2. Refinery facilities and markets perhaps are established on the near-by shore where adjacent fields on land are nearing depletion. 3. There is freedom from jungle pests and tropical diseases. 4. Competitive drilling is less likely. 5. Extensive areas attractive for development arc not yet under lease or concession. Disadvantages are great and numerous: 1. Storm hazards from wind and wave. 2. Expensive foundations, either rigid or floating. 3. Shutdown times because of weather. 4. Marine Regulations of Federal Bureaus in addition to customary regulations on land. 5. Frequent difficulty in moving men and materials to and from drilling platforms. 6. Extra precautions required in open sea. For drilling in water more than 500 or 600 ft. deep, rigid foundations2 become too costly, and floating foundations must be used, and they must meet the following requirements:

Jan 1, 1947

By James Paone

This report shows the feasibility of predicting drillability, analytically, by using regression analysis techniques. The approach is new in diamond-drilling research. Further, the study shows that this technique may be of value to drill manufacturers and others in mathematically delineating performance characteristics of new drills in specific rock types. Another application might be the prediction of penetration speeds in extraterrestrial material based on the physical properties of the materials as samples become available. Prediction equations for penetration rates are presented for 9 rocks drilled in the laboratory and for 20 rocks drilled under field conditions. The prediction equations are based on drill operating parameters and on characteristics of the rock penetrated. No single physical property appeared consistently in the best predictor equations, and all the physical properties were found to be highly correlated with each other.

Jan 1, 1966

By W. D. Mcmillan

The Dempsey tract in Washington County, Mo., had a small production of lead-zinc ore from shallow workings. Old dumps from early-day lead mining contain about 25,000 tons of ore averaging about 3 percent combined zinc and lead. Because of the urgent war requirements for lead and zinc, the Dempsey property was examined by Otto Ruhl, formerly an engineer of the Bureau of Mines in August 1942 and selected for further investigation by churn drilling twenty holes totaling 1,309 feet were bored in the fall of 1943. The results of the work are presented in this paper.

Jan 1, 1948

By C. D. Broadbent

Open pit blasting can be a low cost routine or a high cost bottleneck depending on geology, environment and the operator's ability to master site conditions. Because blasting is a repetitive operation, there should be ample opportunity to optimize the process; but ordinarily this optimization is rarely achieved and then only if conditions remain consistent and predictable. Often, however, and particularly with porphyry coppers, hidden differences in rock characteristics nullify the operator's best efforts. At a porphyry copper deposit being mined by Kennecott Copper Corporation, there are all of the following rock types: oxidized and fresh porphyry, altered and silicified limestone, explosion breccia, rhyolite, sandstone, shale and several others. The units can cover large areas or be limited to a few tens of feet in maximum dimension. They are rarely visible on the bench surface and often do not show up in the bench slope. Even though the blastability of these rocks varies substantially, a generally-uniform blasting pattern was formerly used with disappointing results. Secondary blasting was often required and high bottoms occurred frequently; overblasting wasted drilling time, and explosives caused excessive throw. Several possible methods for improving the blast design were considered and a geophysical method was chosen for testing. There had been reports in the journals that seismic methods were being used in Europe as aids for blasting design. A literature search turned up work by Haxby 1/ on use of a refraction seismograph for measuring pit bench rock strength. Using his work as a springboard, equipment was purchased and a program was planned and carried out for developing, evaluating and implementing the seismic method for routine mine use. Following are discussions of the development program and results.

Jan 1, 1974

By J. J. Harrington

Manufacture and mixing of flotation reagents at the mill site provides an economic and convenient method of maintaining a continuous and fresh supply of reagents for concentrator operations. Kennecott Copper Corporation has designed and built a Reagent Mixing Facility which incorporates new ideas in construction and fail-safe operation at its Nevada Mines Division concentrator. Highly sophisticated automation and instrumentation techniques are combined with safety procedures and equipment that meet and exceed all Federal and State safety requirements. Installation of the facility has minimized hazardous working conditions for the operator, isolated reagent preparation from production personnel and equipment, and reduced the time required for reagent preparation from three shifts to one shift per day.

Jan 1, 1976

By J P. Sykes, C Gemell, A Trench

The perceived and actual impact of government mineral policy upon the government share from gold mining revenues is assessed for ten key countries in which the gold sector is of relevance in advancing economic growth. Five African and five South American jurisdictions are considered, namely Burkina Faso, Ghana, Mali, South Africa and Tanzania from Africa; and Brazil, Chile, Colombia, Guyana and Peru in South America.Both the headline corporate income tax rate and royalty level are identified as poor indicators for the total government share. In addition, significant differences between industry perception and actual government tax levels are identified by this study. The quantitative financial analysis shows that there is no clear relationship between individual taxation rates, taken in isolation, and the overall average effective tax rate (AETR) paid by the project over its life. Neither companies nor governments should use individual taxation rates, or industry perceptions, in isolation to assess the overall competitiveness or equity of a country’s minerals taxation regime – such analysis can be very misleading.In this study, the perceived impact is determined from the well-established Fraser Institute survey published each year, and in 2014 compared 122 minerals jurisdictions globally. The actual impact is determined from quantitative modelling of the financial performance of a hypothetical gold mining project in each country. The technical parameters of the project are held constant; instead the differing mineral policies in each jurisdiction are applied to determine the resultant impact upon the relative share of the economic rents delivered to both private and public sectors. In the quantitative analysis, the total government share varies from 36.3 per cent in South Africa to 66.5 per cent in Ghana.CITATION:Gemell, C, Sykes, J P and Trench, A, 2016. Is perception reality? Evaluating the fiscal attractiveness of international jurisdictions for gold mining investment, in Proceedings International Mine Management Conference, pp 227-238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By W. C. Chang

Phases and magnetic evolutions of melt spun Nd9.5(Fe1-xCox)85.5B5 (x=0, 0.05, 0.1 and 0.15), (Nd1-yLay)9.5Fe85.5B5 (y=0, 0.0.5, 0.1; and 0.15) and (Nd0.95La0.05)9.5(Fe1-zCrz)81.5B9 (z=0, 0.033, 0.067 and 0.1) nanocomposites: have been investigated. It was found that a. dilute Co substitution for Fe, x=0:05-0:15, in Nd9.5(Fe1-xCox) 85.5B5 improved not only Curie temperature but also the remanence and maximum energy product. Partial substitution of La for Nd in(Nd1-yLay)9.5Fe85.5B5 may suppress the grain growth of the materials during thermal treatment. Exchange coupling between the Nd2Fe14B and a-Fe was found: to increase with increasing La content. A dilute La-substitution, y=O. 10, has proven to decrease the optimum wheel speed required for preparing melt spun ribbons with better magnetic properties; Furthermore; a slight substitution of La for Nd in (Nd0.95La0.05)9.5(Fe1-xCrx)81.5B9 nanocomposite reduced the crystallization temperature of the over-quenched ribbons and led to the formation of a multiple phases mixture. Nevertheless, a dilute Cr addition increases the Tg of (Nd0.95La0.05)9.5(Fe1zCrz)81.5B9 and also suppresses the formation of the undesired (Nd,La)2Fe23B3 and Fe3B phases: Cr was found to play an important role in grain smoothening or magnetic separation which consequently increased the Hc of Cr-containing materials.

Jan 1, 1997

By C. F. Tolman

In February 1913, Prof. L. C. Graton and Dr. Joseph Murdochl presented to the American Institute of Mining Engineers a notable contribution to economic geology under the title The Sulphide Ores of Copper. The value of the work was recognized by mine operators, and Mr. Graton was assisted in his plan to extend his investigations, by the organization of a commission to undertake a "secondary enrichment investigation." In this work he secured the cooperation of the Geophysical Laboratory of the Carnegie Institution of Washington. The report2 on the chemical phascs of the investigation has just been published. Incidental to investigations3 carried on in our laboratory of Economic

Jan 1, 1916

By Raymond L. Carpenter

The thermal conductivity, electrical resistivity, and Seebeck coefficient for nine compounds, based on the formula for enargite Cu3AsS3, were measured in a search for efficient materials to be used in thermoelectric generators or refrigerators. Results indicate that one of these compounds, Cu3SbSe4, has thermoelectric properties approaching those of bismuth telluride. An investigation of the effect of adding small quantities of tellurium to Cu3SbSe4 and Cu3SbS4 in order to improve their properties also was made. A figure of merit of 2.1 x 10-4 °C-1 was obtained for Cu3SbSe4 + 0.1 percent tellurium.

Jan 1, 1963

By C. M. Anson

Introduction The prosperity of any country today is dependent upon the efficiency and growth of its primary steel industry. The ?march of the United States of America to its present commanding position in world affairs parallels the growth of its steel industry. The remarkable growth of that industry was possible only because bountiful providence endowed that country with adequate supplies of the raw materials necessary for steel making -coal and iron ore. If we accept this hypothesis, and surely we must, then to what extent can we envisage the future of our own country? This symposium deals with the most important of the raw materials required for steel making -iron ore. If we are blessed with a bountiful supply of iron ore, then surely a glorious future awaits only our taking advantage of that blessing. It is becoming increasingly evident that Canada has immense iron ore deposits. It is my privilege to make you acquainted with one of these, one that can only be classified as among the more important ore reserves in the world. I refer to the Wabana ore deposits in Newfoundland. Location These deposits lie under the floor? of Conception bay, off the east coast of Newfoundland. They consist of a series of beds which outcropped for a distance of about three miles on the northeastern shore of Bell Island, dipping at approximately 8° toward the northwest. This three-mile outcrop is the only key to the occurrence.

Jan 1, 1951

By D. Harrington

Insofar as prevention of mine explosions is concerned, it is apparent that the coal-mining industry has profited but little from experiences during the past 15 years. The fact that explosions can be prevented if well-known preventive measures are adopted and conscientiously carried out appears to warrant the conclusion that many coal-mining people are indifferent to the hazards that may result in explosions. Although the principal burden of preventing explosions is upon the management, and much of the evident carelessness in failing to place in effect and to enforce suitable precautions, is assessable directly against management, the worker also has a very definite responsibility, and numerous explosions have resulted because of his failure to carry out his part in accepted principles of safety. The record of fatalities from mine explosions during the past 5 fiscal years has been anything but encouraging or about which coal-mining people can take pride; more men were killed by explosions (673) than were killed from the same cause during the preceding eight years combined (577). During each of the fiscal years 1942 and 1943, 152 fatalities resulted from explosions, compared to 163 during the fiscal year 1941, 206 in 1940, and only 16 in 1939.

Jan 1, 1944

By R. Alford

In the modern world of demolition safety is paramount and unnecessary or unquantifiable risks are not accepted (FasterCapital, 2024) and all risks must be kept As Low As Reasonably Practicable (ALARP) (BSI, 2017). This principle has led to a huge reduction in deaths in the last 50 years and the statistics continue to improve although this is starting to plateau (Beal, 2007). Under normal circumstances, this is now simply part of the normal way work is done and systems are in place to ensure both safety and economic profits are assured. What happens when the environment is less controlled and risks are unknown, such as after a natural disaster, war, an accident or a stand-up from a failed demolition attempt? A dangerous structure cannot responsibly be left alone with a fence around it so some action must be taken, but how can this be done safely and responsibly? An incident in Didcot, England in which half of a power station’s boiler house being prepared for an explosive demolition collapsed suddenly, killing four men in 2016 provides a useful case study of how technology, creativity and planning can be used to conduct complex demolition fully remotely to avoid any further risk to life.

Jan 21, 2025

By Regina Rocha, Miguel Humpire

One of the challenges within unitary mining operations is blasting, which has a significant downstream impact on the following processes, which is why mining companies ensure the results of the blasting process through joint work with explosives specialists’ companies.

Feb 6, 2023

By J. C. Edwards

The Bureau of Mines developed a mathematical model for analysis of the impact of scrubber bed length, porosity, and gas flow rate on the absorption of C02 in a breathing apparatus. The model accounts for the decrease in available absorbent through chemical conversion. The pre-dicted efflux of C02 from a canister containing LiOR compared favorably with measured values reported elsewhere. It was determined from a com-putational study that the time for breakthrough of C02 at a prescribed level is nearly directly proportional to bed length and inversely pro-portional to gas flow and porosity.

Jan 1, 1987

By F. M. Jenkins

Improvements in miners? safety and health, as reflected by injury and illness statistics, have reached a plateau and even been reversed. Research into miners' OSH is a necessary adjunct to regulatory enforcement. Under the National Occupational Research Agenda (NORA) mining experts have come together to draft a national agenda for this research. The Mining Sector Council, one of ten NORA Sector Councils, has produced a draft national research agenda to guide all mining research entities: academia, government, and industry. The agenda has seven major objectives, each of which has a sequence of sub-objectives: Reduce the likelihood of disasters in mines; Improve mine disaster response; Improve the health of miners; Improve atmospheric control (ventilation) in mines; Improve health and safety through behavioral research; Improve mine design, systems operations, and management performance to enhance mine health and safety; Apply ergonomics, human factor engineering, to increase health and safety. Long-term maintenance of the Mining Research Agenda requires input from the public, both here and abroad, monitoring of the impact of research results using OSH data, and partners who will translate the research to practice.

Jan 1, 2012

By E. Onal

Mining operators are faced with complex information delivered by technology-centric rather than user-centric systems. The ability to achieve high situation awareness (SA) in the face of this data overload is a key challenge for effective decision making and information exploitation. Incidents that result in loss of revenue and even life, and compromise safety that are attributed to human error are often the result of system designs that overload human cognitive capabilities. This paper focuses on defining SA as it relates to mining operations and presents methods for improving SA through a scientific approach for electric shovel operator user interface development.

Aug 1, 2013

By J. Armanet

THREE MINING colleges are maintained in France; the École Nationale Supérieure des Mines, of Paris; École Nationale Supérieure des Mines, of Saint Etienne; and the École Supérieure de la Metallurgie et des Mines at Nancy. Besides graduates of these schools, a few graduates of the École Centrale des Arts et MIanufactures and of the École Polytechnique are employed as ]nine managers or engineers; however, most of the latter have taken a graduate course at one of the mining schools.

Jan 1, 1939

By Jacqueline H. Jansky

The Bureau of Mines conducted a study to determine the relation-ship between geologic features and linears. Cleats, kettlebottoms, and roof rolls were mapped and superimposed on the linear plots for a coal mine in West Virginia. No clear relationships were evident. This may be due, in part, to the mining practice of leaving head coal, which obscures geologic features that may exist in the roof. Future studies should concentrate on mines where roof is extensively exposed.

Jan 1, 1982

By Charles H. Parr

A testing program was conducted to determine the suitability and reliability of adhesives and polycarbonate lenses for extended use in luminaires in mine environments. Polycarbonates were exposed, for periods up to 36 months, to four environments including ultraviolet light, humidity, intermittent water spray, and heat of either 180°F or 407 in various combinations. Rod impact tests on the exposed lens material indicated, that polycarbonate functions well under all 180°F environments and could be used with confidence for periods exceeding the test period, for as long as ten years, with a suit) able safety factor employed in design. The specimens exposed at 240°F showed decreased toughness after 24 months' exposure. Extrapolation of these data was deemed to be risky. A 462-day compatibility test between polycarbonate and six hydraulic fluids was run on stressed PC beams. One fluid caused beam breakage in less than one day, while three caused breakage at intermediate times. Two fluids exhibited essentially no effect on the PC when compared to a control. Epoxy and silicone adhesives were tested as lens adhesives and sealants. Three epoxy combinations tested showed low and erratic failure stresses. A room-temperature-cure silicone adhesive functioned extremely well for time periods up to 36 months and temperatures u2 to 240°F.

Jan 1, 1985